Geology topics

Groundwater & aquifers

Find USGS groundwater and aquifer publications. Search an aquifer name or place, compare source-supplied dates and open reports for hydrogeology, recharge and water-level studies.

Follow this topic with RSS

476 records · Page 10Linked to original sources

USGS1998

Water resources of Mellette and Todd counties, South Dakota

Mellette and Todd Counties are located in south-central South Dakota and have a combined area of 2,694 square miles. The White River and its tributaries, which include the Little White River, drain Mellette County and about one-half of Todd County. Tributaries to the Niobrara River, which include the Keya Paha River, drain the other one-half of Todd County. The average discharge of the Little White River is about 56 cubic feet per second as the river enters Todd County and is about 131 cubic feet per second as it discharges to the White River in northern Mellette County. The average discharge of the Keya Paha River just outside Todd County is about 39 cubic feet per second. The average annual runoff for Mellette and Todd Counties ranges from 0.94 to 2.36 inches based on records from nine streamflow-gaging stations in and near the counties. The average annual runoff is 1.62 inches, which compares with the average annual precipitation of about 19 inches. In Todd County, shallow wells completed in the alluvial, Ogallala, Arikaree, and White River aquifers generally can supply water that has low concentrations of dissolved solids, is fresh, and is soft to moderately hard. Ground water from shallow aquifers is limited in Mellette County; therefore, deep wells, often greater than 1,000 feet, are sometimes installed. The Pierre Shale often is used to supply rural domestic and stock wells in Mellette County even though well yields are low and the water has high dissolved solids, is moderately saline, and is very hard. Alluvial aquifers are present in both counties and store an estimated 1.6 million acre-feet of water. The water quality of the alluvial aquifers is dependent on the underlying deposits, and generally the water has low concentrations of dissolved solids, is fresh, and is soft to moderately hard where underlain by the Ogallala and Arikaree Formations; has moderate concentrations of dissolved solids, is slightly saline, and is hard where underlain by the White River Group; and has high concentrations of dissolved solids, is saline, and is very hard where underlain by the Pierre Shale. Also, yields often are lower where the alluvial aquifers are underlain by the Pierre Shale. The Ogallala aquifer is present in only Todd County, and the Arikaree aquifer is present throughout most of Todd County and southwestern and south-central Mellette County. The Ogallala aquifer contains an estimated 17 million acre-feet of water in storage, and the Arikaree aquifer contains an estimated 50 million acre-feet of water in storage. Both aquifers generally are suitable for irrigation, and yields from these aquifers are sometimes greater than 1,000 gallons per minute. Nitrate concentrations in 13 out of 92 water samples collected from the Ogallala aquifer exceeded the Primary Drinking Water Maximum Contaminant Level (MCL) of 10 milligrams per liter. In 11 out of 46 samples collected from the Arikaree aquifer, arsenic concentrations exceeded the MCL of 50 micrograms per liter. The White River aquifer, where present, is usually the shallowest source of ground water in Mellette County. The White River aquifer also is used in northern Todd County where the Ogallala and Arikaree aquifers are not present. The White River aquifer contains an estimated 50 million acre-feet of water in storage. Reported yields from the aquifer range from 1 to 30 gallons per minute, which generally is insufficient to support irrigation in most areas. However, yields are sufficient for livestock-watering and rural-domestic purposes. In both counties, the Pierre Shale is the shallowest bedrock aquifer and is exposed at the land surface throughout most of Mellette County. This aquifer is used primarily in Mellette County. Although the aquifer contains an estimated maximum of 1.5 million acre-feet of water in storage, it is not a viable source of ground water because the aquifer is relatively impermeable, yields are low, and water usually can be obtained from shallower sources, especially in Todd County. Reported yields from the Pierre Shale aquifer range from 1 to 8 gallons per minute. Because few test holes and wells penetrate below the Pierre Shale, little is known about the extent of the deeper bedrock aquifers. All wells completed in the Dakota Sandstone, Inyan Kara, and Minnelusa and Madison aquifers in the counties are used for stock-watering purposes. High concentrations of dissolved solids and hard water are characteristic of the water quality in the bedrock aquifers. Depths to the top of the deeper bedrock aquifers range from 1,270 feet to greater than 2,000 feet below land surface.

South Dakota↗

USGS1995

The distribution of bromide in water in the Floridan aquifer system, Duval County, northeastern Florida

Although Duval County, Florida, has ample ground-water resources for public supply, the potential exists for a problem with excessive disinfectant by-products. These disinfectant by-products result from the treatment of raw water containing low concentrations of bromide and naturally occurring organic compounds. Because of this potential problem, the relation of bromide concentrations to aquifer tapped, well location and depth, and chemical characteristics of water in the Floridan aquifer system underlying Duval County were studied to determine if these relations could be applied to delineate water with low-bromide concentrations for future supplies. In 1992, water samples from 106 wells that tap the Floridan aquifer system were analyzed for bromide and major dissolved constituents. A comparison of bromide concentrations from the 1992 sampling with data from earlier studies (1979-80) indicates that higher bromide concentrations were detected during the earlier studies. The difference between the old and new data is probably because of a change in analytical methodology in the analysis of samples. Bromide concentrations exceeded the detection limit (0.10 milligrams per liter) in water from 28 of the 106 wells (26 percent) sampled in 1992. The maximum concentration was 0.56 milligrams per liter. There were no relations between bromide and major dissolved constituents, well depth, or aquifer tapped that would be useful for determining bromide concentrations. Areal patterns of bromide occurrence are not clearly defined, but areas with relatively high bromide concentrations tend to be located in a triangular area near the community of Sunbeam, Florida, and along the St. Johns River throughout Duval County.

Florida↗

USGS1993

Geochemistry of and radioactivity in ground water of the Highland Rim and Central Basin aquifer systems, Hickman and Maury counties, Tennessee

A reconnaissance of the geochemistry of and radioactivity in ground water from the Highland Rim and Central Basin aquifer systems in Hickman and Maury Counties, Tennessee, was conducted in 1989. Water in both aquifer systems typically is of the calcium or calcium magnesium bicarbonate type, but concentrations of calcium, magnesium, sodium, potassium, chloride, and sulfate are greater in water of the Central Basin system; differences in the concentrations are statistically significant. Dissolution of calcite, magnesium-calcite, dolomite, and gypsum are the primary geochemical processes controlling ground-water chemistry in both aquifer systems. Saturation-state calculations using the computer code WATEQF indicated that ground water from the Central Basin system is more saturated with respect to calcite, dolomite, and gypsum than water from the Highland Rim system. Geochemical environments within each aquifer system are somewhat different with respect to dissolution of magnesium-bearing minerals. Water samples from the Highland Rim system had a fairly constant calcium to magnesium molar ratio, implying congruent dissolution of magnesium-bearing minerals, whereas water samples from the Central Basin system had highly variable ratios, implying either incongruent dissolution or heterogeneity in soluble constituents of the aquifer matrix. Concentrations of radionuclides in water were low and not greatly different between aquifer systems. Median gross alpha activities were 0.54 picocuries per liter in water from each system; median gross beta activities were 1.1 and 2.3 picocuries per liter in water from the Highland Rim and Central Basin systems, respectively. Radon-222 concentrations were 559 and 422 picocuries per liter, respectively. Concentrations of gross alpha and radium in all samples were substantially less than Tennessee’s maximum permissible levels for community water-supply systems. The data indicated no relations between concentrations of dissolved radionuclides (uranium, radium-226, radium-228, radon-222, gross alpha, and gross beta) and any key indicators of water chemistry, except in water from the Highland Rim system, in which radon-222 was moderately related to pH and weakly related to dissolved magnesium. The only relation among radiochemical constituents indicated by the data was between radium-226 and gross alpha activity; this relation was indicated for water from both aquifer systems.

Tennessee↗

USGS2025

Simulated hydrologic responses to proposed wastewater-returnflow scenarios in Falmouth, Massachusetts

The Cape Cod aquifer is the sole source of drinking water for communities on Cape Cod, Massachusetts, including the Town of Falmouth, where the aquifer is currently threatened by contamination from septic-system-derived nitrogen. To address this problem, the Town is proposing to sewer areas of Falmouth, treat the wastewater at the Town’s Main Wastewater Treatment Facility (a nitrogen removing/tertiary treatment facility), and discharge the treated wastewater to an ocean outfall pipe in Nantucket Sound. The U.S. Geological Survey, in cooperation with the Town of Falmouth, updated a three-dimensional steady-state groundwater flow model to represent current (defined as 2019–23) average hydrologic conditions and to simulate the long-term average freshwater hydrologic response to two wastewater-return-flow scenarios. Scenario 1 involves the sewering of all properties south of Route 28 in Falmouth, which approximates the Town’s possible sewer expansion over the next 20–30 years. Scenario 2 involves sewering of all properties in Falmouth to demonstrate the maximum potential effect of sewering on the aquifer. Overall, the simulated hydrologic response of water-table altitudes and streamflow in both scenarios was relatively small compared to fluctuations from natural recharge. In scenario 1, the water-table altitude decreased by about 0.1 feet south of Route 28, where the conversion to municipal sewers removed wastewater-return flow from onsite septic systems. The water-table altitude decreased by about 0.1–0.2 feet over a larger area in Falmouth under town-wide sewering in scenario 2. The greatest decrease in water-table altitude in both scenarios occurred near the Main Wastewater Treatment Facility, with a decrease of about 1.1 feet in scenario 1 and about 1.3 feet in scenario 2. Simulated decreases in streamflow also were estimated for six selected streams in Falmouth and Mashpee. In both scenarios, the largest simulated decreases in streamflow were at the Coonamessett River, which is the closest stream to the Main Wastewater Treatment Facility. In scenario 1, the average annual decrease in flow at the Coonamessett River was 0.1 cubic feet per second, a 1.1 percent decrease from current (2019–23) conditions. In scenario 2, streamflow at the Coonamessett River decreased by 0.6 cubic feet per second, a 5.4 percent decrease from current (2019–23) conditions.

Massachusetts↗

USGS1986

Potential for leakage among principal aquifers in the Memphis area, Tennessee

The principal aquifers in the Memphis area consist primarily of sand or sand and gravel, and the confining beds consist of clay, silt, sand, and lignite. The Jackson Formation and upper part of the Claiborne Group serve as the confining bed separating the water table aquifers from the Memphis Sand; the Flour Island Formation separates the Memphis Sand from the Fort Pillow Sand. Differences in total hydraulic head among the principal aquifers in the Memphis urban area result in vertical hydraulic gradients which create a potential for inter-aquifer exchange of water. Throughout this area, the gradient is downward from the water table aquifers to the Memphis Sand. In the central part of the Memphis urban area, the vertical hydraulic gradient is upward from the Fort Pillow Sand to the Memphis Sand, and in the eastern and western parts, it is downward from the Memphis Sand to the Fort Pillow Sand. The vertical distribution of carbon-14 data for water from the fluvial deposits, Memphis Sand, and Fort Pillow Sand shows an increase in the relative age of the water with depth. The areal distribution of carbon-14 data for water from the upper part of the Memphis Sand indicates that relatively recent water has been brought into the major cone of depression in the potentiometric surface of the Memphis Sand, either by horizontal movement or from downward vertical leakage. The normal, near-surface geothermal gradient in the Memphis area was determined to be 0.6 C/100 ft. Deviations from the normal geothermal gradient, in areas affected by intense pumping from the Memphis Sand, indicate that downward vertical leakage occurs from the water table aquifers through the Jackson-upper Claiborne confining bed to the Memphis Sand. The velocity of downward vertical leakage of water from the Memphis Sand through the Flour Island confining bed to the Fort Pillow Sand was determined to be 0.0066 ft/day by analysis of borehole temperature data from an observation well in the northeastern part of the Memphis area. From this velocity and the head difference between the Memphis Sand and the Fort Pillow Sand at this locality, the hydraulic conductivity of the Flour Island confining bed was determined to be 0.00114 ft/day. (Lantz-PTT)

Tennessee↗

USGS1998

Transmissivity and water quality of water-producing zones in the intermediate aquifer system, Sarasota County, Florida

The intermediate aquifer system is an important water source in Sarasota County, Florida, because the quality of water in it is usually better than that in the underlying Upper Floridan aquifer. The intermediate aquifer system consists of a group of up to three water-producing zones separated by less-permeable units that restrict the vertical movement of ground water between zones. The diverse lithology, that makes up the intermediate aquifer system, reflects the variety of depositional environments that occurred during the late Oligocene and Miocene epochs. Slight changes in the depositional environment resulted in aquifer heterogeneity, creating both localized connection between water-producing zones and abrupt culmination of water-producing zones that are not well documented. Aquifer heterogeneity results in vertical and areal variability in hydraulic and water-quality properties. The uppermost water-producing zone is designated producing zone 1 but is not extensively used because of its limited production capability and limited areal extent. The second water-producing zone is designated producing zone 2, and most of the domestic- and irrigation-supply wells in the area are open to this zone. Additionally, producing zone 2 is utilized for public supply in southern coastal areas of Sarasota County. Producing zone 3 is the lowermost and most productive water-producing zone in the intermediate aquifer system. Public-supply well fields serving the cities of Sarasota and Venice, as well as the Plantation and Mabry Carlton Reserve well fields, utilize producing zone 3. Heads within the intermediate aquifer system generally increase with aquifer depth. However, localized head-gradient reversals occur in the study area, coinciding with sites of intense ground-water withdrawals. Heads in producing zones 1, 2, and 3 range from 1 to 23, 0.2 to 34, and 7 to 42 feet above sea level, respectively. Generally, an upward head gradient exists between producing zones 3 and 2. However, an upward head gradient between producing zones 2 and 1 does not consistently occur throughout Sarasota County, probably the result of greater ground-water withdrawals from producing zone 2 than from producing zone 1. The transmissivity of the intermediate aquifer system is spatially variable. Specific-capacity data from selected wells penetrating producing zones 2 and 3, were used to estimate transmissivity. Estimated transmissivity values for producing zones 2 and 3 range from about 100 to 26,000 feet squared per day and from about 1,300 to 6,200 feet squared per day, respectively. Because the capacity of specific water-producing zones is highly variable from site to site, estimating the performance of a specific water-producing zone as a water resource is difficult. Water samples collected during the study were analyzed for major-ion concentrations. Generally, bicarbonate type water from rock interaction occurs in northern Sarasota County; enriched calcium-magnesium-sulfate type water from deeper aquifers occurs in central Sarasota County; and sodium-chloride type water from saltwater mixing occurs in southern Sarasota County. In some areas of northern Sarasota County, the major-ion concentrations in water are lower in producing zone 2 than in producing zone 1. Major-ion concentrations in water are higher in producing zone 3 throughout the study area. A major objective of the study was to evaluate hydraulic and water-quality data to determine distinctions that could be used to characterize a particular producing zone. However, data indicate that both hydraulic and water-quality properties are highly variable within and between zones, and are more related to the degree of connection between and areal extent of water-producing zones than to aquifer depth and distance from the coast.

Florida↗

USGS1997

Chemical evolution and estimated flow velocity of water in the Trinity Aquifer, south-central Texas

Three permeable zones with varying lithology and water chemistry compose the Trinity aquifer, a principal source of water in the 5,500- square-mile study area in south-central Texas. The upper permeable zone locally yields small quantities of water to wells and was not included in this study. The middle permeable zone primarily is composed of limestone with minor amounts of dolostone. Terrigenous sand and marine limestone, with minor amounts of dolostone, are the principal lithologic units in the lower permeable zone. Dissolved solids concentrations range from 329 to 1,820 milligrams per liter in water samples from the middle permeable zone and from 518 to 3,030 milligrams per liter in water samples from the lower permeable zone. Principal hydrochemical facies in the middle permeable zone are calcium magnesium bicarbonate and calcium magnesium sulfate. Hydrochemical facies in ground-water samples from the lower permeable zone vary. Tritium concentrations as large as 5.3 tritium units in the southeastern part of the study area are indicative of relatively recent recharge. Results of a geochemical mass balance simulation along a flowpath in the middle permeable zone indicate a mass transfer of 4.25 millimoles per liter of dolomite dissolved, 5.74 millimoles per liter of gypsum dissolved, 0.46 millimole per liter of sodium chloride dissolved, 8.07 millimoles per liter of calcite precipitated, and 0.67 millimole per liter of calcium-for-sodium cation exchange between solid and aqueous phases. These results support dedolomitization as a principal chemical process in the middle permeable zone of the Trinity aquifer. Results of a simulation along a flowpath in the lower permeable zone indicate a mass transfer of 0.41 millimole per liter of dolomite dissolved, 0.001 millimole per liter of gypsum dissolved, 9.58 millimoles per liter of sodium chloride dissolved, 1.09 millimoles per liter of calcite precipitated, and 1.11 millimoles per liter of sodium-forcalcium cation exchange between solid and aqueous phases. Lower permeable zone processes indicate sodium chloride dissolution, dedolomitization, and cation exchange. Ground-water-flow velocities determined from adjusted carbon-14 ages, calculated using NETPATH, for selected flowpaths in the middle and lower permeable zones were about 1.7 feet per year and less than about 4.4 feet per year, respectively.

Texas↗

USGS2025

Factors affecting the distribution of water-bearing fractures in the bedrock aquifers of West Virginia

Bedrock aquifers cover 23,601 square miles within the State of West Virginia and comprise 97.4 percent of the surficial area within the State; the remaining 2.6 percent (621 square miles) consists of alluvial sand-and-gravel and glacial outwash aquifers bordering the State’s major rivers. While West Virginia’s alluvial aquifers have been studied extensively, bedrock aquifers have only been characterized for studies completed in a few areas in Jefferson, McDowell, and Monroe Counties. Bedrock aquifers are water supplies for public supply, agriculture, industry, and residential homeowner use. In this study, the U.S. Geological Survey, in cooperation with the West Virginia Department of Environmental Protection Division of Water and Waste Management, provides a statewide assessment of the occurrence and distribution of fractures within bedrock aquifers of the State and the various topographic, physiographic, and lithologic influences controlling the occurrence and distribution of bedrock fractures. The results of this study provide an increased understanding of the distribution of fractures in bedrock aquifers in West Virginia and help to verify trends that have been suspected for many years but were never well documented or verified by data. The results confirmed that the density of fractures and those that were determined to be water bearing decrease significantly with depth. A statistically significant difference in the density of fractures was observed at a depth of 215 feet for wells in the Appalachian Plateaus Physiographic Province’s and in the Valley and Ridge Physiographic Province’s aquifers; a higher density of fractures and water-bearing fractures were above a depth of 215 feet than below that depth. This is an important consideration when drilling wells for residential, commercial, industrial, or agricultural water supply. Abandoned underground coal mines are commonly believed to form large pools of water in the interconnected mine entries in abandoned room and pillar coal mines. Such pools of water can and do exist in abandoned underground coal mines, but many mines lack open entries and are held up by overburden strata and pillars that can collapse and form aquifers comprised of vast interconnected rubble zones (gob), especially in older mines. Data assessed for this study showed that shale-corrected values of effective porosity for limestone aquifers in West Virginia had a median value of 2 percent and an average value of 4 percent and generally are mineralized with low effective porosity. Argillaceous or sandy limestone has a median shale-corrected porosity of 4 percent and an average shale-corrected porosity of 5 percent. The median and average shale-corrected porosity of sandstone aquifers was estimated to be 14 percent, but the median shale-corrected porosity for argillaceous or calcareous sandstone was 5 percent and the average shale-corrected porosity for argillaceous or calcareous sandstone was 6 percent. Even though shale has a relatively high total sonic porosity compared to other lithologies, shale and siltstone had relatively low shale-corrected porosity, ranging from 0 to 2 percent. Well yields were previously documented to be highest in valley settings, lowest on hilltops, and intermediate on hillsides. Transmissivity data provided by this study confirm this general pattern within the Appalachian Plateaus Province; however, the Valley and Ridge Province does not follow this pattern. While still lowest on hilltop settings, the highest well yields were in hillside settings. The trend for the Valley and Ridge Province was likely skewed because of 9 high-yield wells specifically targeting deeper thin limestone units, such as the Tonoloway and Helderberg Limestones, at depths with transmissivity in excess of 2,000 feet squared per day in Mineral County, West Virginia, or targeting karst aquifers in Berkeley, Jefferson, or Greenbrier Counties, West Virginia. Finally, water-bearing fractures have been hypothesized to comprise a small number of all fractures within a typical bedrock well in West Virginia. Data collected for this study support this theory. A total of 3,403 fractures were identified during this study; 3,151 (92.6 percent) of those fractures are low-transmissive, and only 252 (7.4 percent) fractures are water-bearing. Even though a well may contain many fractures, less than 8 percent are considered water-bearing fractures.

West Virginia↗

USGS1976

Availability of ground water in the area surrounding the Trident submarine construction facility, Kitsap County, Washington

This report provides general information on the water resources--with emphasis on ground-water occurrence and availability--in that part of Kitsap County (referred to as Trident Impact Area) that would be most affected by the development of the Trident submarine-construction facility at Bangor. Ground water occurs principally in a lower, confined aquifer near and below sea level and an upper, unconfined aquifer above sea level; both aquifers are extensive beneath the study area and are composed of sand and gravel layers separated by poorly permeable silt, clay, and till layers. Locally throughout the area efficiently constructed wells tapping each of the two aquifers are capable of yielding 100 to 1,300 or more gallons per minute. The estimated 1970 water use in the study area averaged about 13 million gal/day (gallons per day); of this amount about 9 million gal/day came from surface-water sources--from a large reservoir outside the study area--and about 4 million gal/day came from ground water pumped from the two aquifers. Anticipated water use soon will be about 18 to 21 million gal/day; virtually all the additional quantity required (about 5 to 8 million gal/day) above present use must come from ground-water sources. Preliminary evaluation of the aquifers suggests that an additional 1.5 million gal/day can be developed from the upper aquifer and 7 million gal/day from the lower aquifer. Existing wells tapping the lower aquifer might yield additional water and increase the total yield in the area by 3.5 million gal/day, and new wells drilled in selected areas could produce an additional 3.5 million gal/day from this aquifer. However, additional, large-scale ground-water withdrawal from the lower aquifer could induce saltwater intrusion into wells situated in coastal areas. Recommended future studies include additional data collection, monitoring of chloride concentrations in water from large-yield coastal wells, confirmation of well yields and capacities, and test-well drilling and analysis.

Washington↗

USGS2026

Hydrologic investigation of water level fluctuations at Moreau Lake, Moreau Lake State Park, town of Moreau, New York

The causes of water level fluctuations at Moreau Lake, within Moreau Lake State Park in the town of Moreau, New York, were investigated from 2016 to 2021 after lake water levels dropped between 2015 and 2016, raising concerns about the loss of a shallow swimming area at the park beach. Annual variation in precipitation records from the area did not account for the lake water level decline. Two possible causes for the low lake water levels were investigated: the increase in groundwater withdrawals from new residential development since about 2000 and seasonal changes (nongrowing and growing seasons) in precipitation. Investigation of the potential effects of nearby groundwater withdrawals required the compilation and collection of well-log data, seismic surveys, and measurements of lake and groundwater levels, field chemical parameters, and water isotopes to define the hydrogeologic system and to estimate water use. The net result of this work was the determination that Moreau Lake is a “flow though” lake with no surface water outlet; groundwater enters the lake on the upgradient side and exits through the downgradient side, however, groundwater does not flow southward from the lake toward nearby groundwater withdrawals from the semiconfined aquifer, and thus groundwater withdrawals were unlikely to have an effect on lake water levels. Investigation of the historic precipitation records during nongrowing (November through April) and growing (May through October) indicated that (1) nongrowing season precipitation from 2011–12 to 2015–16 was more deficient than any similar period during the past 78 years and (2) since about 2000, nongrowing seasons have been drier overall and growing seasons have been considerably wetter. Initiation of lake water level monitoring in 2016 provided an opportunity to compare seasonal precipitation with seasonal lake water level changes. Nongrowing season lake water levels are very sensitive to precipitation, such that high precipitation (40 percent above the seasonal median) resulted in a 5-foot rise in lake water level. In contrast, the growing season lake water levels are sensitive to dry conditions; for example, deficient rainfall (about 6 percent below the seasonal median) resulted in a decline of lake water levels of about 3.5 feet. However, lake water levels are insensitive to high growing season rainfall inputs (about 10 to 47 percent above the seasonal median); lake water levels consistently declined about by 0.8 feet above this range of seasonal excessive precipitation.

New York↗

USGS1998

Ground-water flow in the surficial aquifer system and potential movement of contaminants from selected waste-disposal sites at Naval Station Mayport, Florida

Ground-water flow through the surficial aquifer system at Naval Station Mayport near Jacksonville, Florida, was simulated with a two-layer finite-difference model as part of an investigation conducted by the U.S. Geological Survey. The model was calibrated to 229 water-level measurements from 181 wells during three synoptic surveys (July 17, 1995; July 31, 1996; and October 24, 1996). A quantifiable understanding of ground-water flow through the surficial aquifer was needed to evaluate remedial-action alternatives under consideration by the Naval Station Mayport to control the possible movement of contaminants from sites on the station. Multi-well aquifer tests, single-well tests, and slug tests were conducted to estimate the hydraulic properties of the surficial aquifer system, which was divided into three geohydrologic unitsï¿½an S-zone and an I-zone separated by a marsh-muck confining unit. The recharge rate was estimated to range from 4 to 15 inches per year (95 percent confidence limits), based on a chloride-ratio method. Most of the simulations following model calibration were based on a recharge rate of 8 inches per year to unirrigated pervious areas. The advective displacement of saline pore water during the last 200 years was simulated using a particle-tracking routine, MODPATH, applied to calibrated steady-state and transient models of the Mayport peninsula. The surficial aquifer system at Naval Station Mayport has been modified greatly by natural and anthropogenic forces so that the freshwater flow system is expanding and saltwater is being flushed from the system. A new MODFLOW package (VAR1) was written to simulate the temporal variation of hydraulic properties caused by construction activities at Naval Station Mayport. The transiently simulated saltwater distribution after 200 years of displacement described the chloride distribution in the I-zone (determined from measurements made during 1993 and 1996) better than the steady-state simulation. The advective movement of contaminants from selected sites within the solid waste management units to discharge points was simulated using MODPATH. Most of the particles were discharged to the nearest surface-water feature after traveling less than 1,000 feet in the ground-water system. Most areas within 1,000 feet of a surface-water feature or storm sewer had traveltimes of less than 50 years, based on an effective porosity of 40 percent. Contributing areas, traveltimes, and pathlines were identified for 224 wells at Naval Station Mayport under steady-state and transient conditions by back-tracking a particle from the midpoint of the wetted screen of each well. Traveltimes to contributing areas that ranged between 15 and 50 years, estimated by the steady-state model, differed most from the transient traveltime estimates. Estimates of traveltimes and pathlines based on steady-state model results typically were 10 to 20 years more and about twice as long as corresponding estimates from the transient model. The models differed because the steady-state model simulated 1996 conditions when Naval Station Mayport had more impervious surfaces than at any earlier time. The expansion of the impervious surfaces increased the average distance between contributing areas and observation wells.

Florida↗

USGS2026

Geologic framework, hydrostratigraphy, and ichnology of the Blanco, Payton, and Rough Hollow 7.5-minute quadrangles, Blanco, Comal, Hays, and Kendall Counties, Texas

During 2023, the U.S. Geological Survey, in cooperation with the Edwards Aquifer Authority, revised an initial characterization completed during 2015–16 of the geologic framework, hydrostratigraphy, and ichnology of the Edwards and Trinity aquifers in the Blanco, Payton, and Rough Hollow 7.5-minute quadrangles in Blanco, Comal, Hays, and Kendall Counties, Texas. The purpose of this report is to present the updated geologic framework, hydrostratigraphy, and ichnology of the Trinity and Edwards Groups in those quadrangles. Rocks exposed in the study area are of the Lower Cretaceous Trinity Group and lower part of the Fort Terrett Formation of the Lower Cretaceous Edwards Group. The faulting and fracturing in the study area are part of the Balcones Fault Zone, an extensional system of faults active during the Paleocene to middle Eocene that generally trends southwest to northeast in south-central Texas. Hydrostratigraphically, the rocks exposed in the study area contain a section of the Edwards (Balcones Fault Zone) aquifer, upper zone of the Trinity aquifer, and middle zone of the Trinity aquifer. In the study area, the only hydrostratigraphic units of the Edwards (Balcones Fault Zone) aquifer remaining are (from top to bottom) VII and VIII, which cap several hills. The mapped hydrostratigraphic units of the upper zone of the Trinity aquifer are (from top to bottom) the cavernous, Camp Bullis, upper evaporite, fossiliferous, and lower evaporite. The mapped hydrostratigraphic units of the middle zone of the Trinity aquifer are (from top to bottom) the Bulverde, Little Blanco, Twin Sisters, Doeppenschmidt, Herff Falls (where present), Rust, Honey Creek, Hensell, and Cow Creek hydrostratigraphic units.

Texas↗

USGS1997

Integrity of production wells and confining unit at the Naval Weapons Industrial Reserve Plant, Dallas, Texas, 1995

Ground water in the shallow alluvial aquifer is contaminated at the Naval Weapons Industrial Reserve Plant, Dallas, Texas. Five production wells at the site are cased through the alluvial aquifer and underlying units and are screened in either the Paluxy or Twin Mountains aquifers. Three abandoned wells, originally completed in the Twin Mountains aquifer but filled with drilling mud in 1958, also penetrate the alluvial aquifer. The Paluxy and Twin Mountains aquifers are used for drinking-water supplies in and around the Dallas-Fort Worth metroplex. Trichloroethylene and its degradation products, dichloroethylene and vinyl chloride, and the metal chromium previously have been detected in the shallow alluvial aquifer. Current (1995) analyses of water-quality samples taken from the static water column of the five production wells and one of the abandoned wells indicate no trichloroethylene, dichloroethylene, or vinyl chloride in the water column of these wells. Chromium was detected in all samples, but concentrations were less than the practical quantitation limit, which is the regulatory action level for this site. The results of borehole geophysical log analysis indicate that two of the production wells could have vertically connected intervals where cement bonding in the well annulus is poor. The other production wells have overall good bonding. Temperature logs do not indicate flow behind casing except in the screened interval of one well. Geophysical logs show the Eagle Ford Shale ranges from 147 to 185 feet thick at the site. The Eagle Ford Shale has low permeability and a high plasticity index. These physical characteristics make the Eagle Ford Shale an excellent confining unit.

Texas↗

USGS2024

Simulated mean monthly groundwater-transported nitrogen loads in watersheds on the north shore of Long Island Sound, 1993–2022

Elevated nitrogen loads are pervasive in the Long Island Sound, an estuary that receives freshwater and nutrients from both surface-water and groundwater discharge. Surface-water nitrogen loads to the Long Island Sound are relatively well characterized, but less is known about groundwater-transported nitrogen loads. Prior work on the northern shore of Long Island Sound (Connecticut and areas of New York and Rhode Island) suggested that groundwater travel times are relatively short (median less than 2 years) and that decade-long nutrient legacies are not widespread. Because the travel times are short, groundwater flow and nutrient loads likely vary substantially between months. In the current study, the U.S. Geological Survey, in cooperation with the U.S. Environmental Protection Agency’s Long Island Sound Study and the Connecticut Department of Energy and Environmental Protection, developed a set of models to better characterize spatial and temporal patterns of groundwater-transported nitrogen loading from atmospheric deposition, septic systems, and fertilizers within the study area. The models provide an estimate, with uncertainty, of groundwater-transported nitrogen loads in the study area, filling a key gap in the nitrogen budget for Long Island Sound. The models also highlight the spatial and temporal variation in nitrogen loading throughout the study area. The modeling workflow involved four models. (1) A soil-water-balance model was developed by using the Soil-Water-Balance software to simulate groundwater recharge across the study area for water years 2005 through 2022. The simulated mean monthly recharge from the soil-water-balance model was used as input into a groundwater-flow model. (2) The groundwater-flow model was developed by using the MODFLOW 6 software and data for water years 1993 through 2022 and simulates average monthly hydrologic conditions. The groundwater-flow model was calibrated by using the Iterative Ensemble Smoother method within the PEST++ software. The Iterative Ensemble Smoother method generates an ensemble of sets of parameter values, with each set producing reasonable simulated hydrologic parameter values. (3) An ensemble of MODPATH particle-tracking simulations were run to generate particle flow paths and travel times, with each simulation using a different set of the flow model parameters. (4) A nitrogen load model uses the MODPATH simulation outputs to track nitrogen from the land surface through multiple attenuation zones until it discharges into fresh or saline surface water. As with the groundwater-flow model, the nitrogen model simulated average monthly groundwater-transported nitrogen loads for water years 1993 through 2022. One novel aspect of the nitrogen load model is that the nitrogen attenuation parameters were calibrated to observed nitrogen loads. Across the ensemble of simulated nitrogen loads, the median study-area-wide monthly simulated nitrogen loads from the aquifer to Long Island Sound throughout the year ranged from 900 to 18,600 kilograms of nitrogen per day, with a median load of 5,100 kilograms of nitrogen per day. The simulated loads were based on average monthly conditions for water years 1993 through 2022. Loads were highest during the winter and early spring and lowest during the late summer. However, simulated travel times for groundwater and nitrogen loads discharged to Long Island Sound during summer were longer than travel times for groundwater and loads discharged during the winter, indicating that, on average, groundwater discharged during summer traveled along different, and longer, flow paths, than groundwater discharged during winter. This indicates that summer loads would respond more slowly to changes in nitrogen inputs at the water table than winter loads. Over the entire study area, approximately 15 percent of the simulated load is from atmospheric deposition sources, 30 to 40 percent is from fertilizer, and 50 to 60 percent is from septic systems. The final analysis of the study involved simulating the change in groundwater-transported nitrogen load in response to upgrading septic systems or reducing fertilizing inputs to areas of turf grass. Both management interventions reduced the groundwater-transported nitrogen load, and reductions were greater in areas with greater loads from septic systems or turf-grass fertilizers. The delay between management actions and substantial reductions in groundwater-transported nitrogen loads varied seasonally; loads during the late summer months remained elevated longer than the winter loads.

Connecticut, Rhode Island↗

USGS1973

Geohydrology of the Cross-Florida Barge Canal area, with special reference to the Ocala vicinity

The Cross-Florida Barge Canal route commences at Palatka on the St. Johns River, about 75 miles upstream from the Atlantic Ocean, and extends 110 miles southwestward across Peninsular Florida into deep water in the Gulf of Mexico near Yankeetown. The canal will be equipped with five locks, each 600 feet long and 84 feet wide, and the channel will be a minimum of 12 feet deep and 150 feet wide. From near Ocala northeastward, the canal channel will replace much of the natural channel of the Oklawaha River, and will be excavated into beds of the so-called shallow sand aquifer of Miocene age and younger, which overlies limestone of the Floridan aquifer. Westward from Ocala, most of the canal will be excavated below the potentiometric surface into limestone and dolomite of the Floridan aquifer. Water levels of Rodman, Eureka, and Inglis Pools will be controlled by dams and spillways with the limited exchange of water between the pools and the aquifers. The water levels in the Summit Pools will fluctuate with the natural changes in the ground-water level of the Floridan aquifer, although the stage of the pool will be controlled partly by the stage held in the Eureka Pool. A dynamic inflow-outflow relationship will exist between the Summit Pool and the Floridan aquifer. The Floridan aquifer in the canal area is 1,000 to 1,200 feet thick and consists of limestone and dolomite of middle Eocene Miocene age, including from older to younger, the Lake City, Avon Park, and Ocala limestones plus permeable sandy, dolomitic limestone in the lower part of the Hawthorn Formation. It is possible that most of the flow to the two major springs in the area occurs in the upper 100 feet or so of the aquifer in the Ocala Limestone. The aquifer is underlain by the Oldsmar limestone of early Eocene age and is overlain by sand, clayey sand, clay and shell beds of Miocene through Holocene age, in thickness from a few feet to 300 feet. The permeable beds overlying the Floridan aquifer constitute the shallow aquifer, while the poorly permeable ones act as confining beds where the Floridan aquifer is under artesian conditions. A north-south line drawn separating the head of Silver Springs on the west from the Oklawaha River on the east marks the approximate western limit of a continuous blanket of materials of Miocene-Pliocene(?) age covering the rocks of the Floridan aquifer. East of the line, much of the aquifer is under artesian conditions, particularly in the Oklawaha River valley, although in some areas east of the valley, direct recharge through thick permeable Miocene-Pliocene(?) sands occurs. West of the line, only scattered remnants of a once continuous Miocene-Pliocene(?) cover remain. Lack of the cover is a result of erosion on the crest and flank of the Ocala Uplift, a broad northwest-southeast trending anticlinal upwarp, the axis of which is crossed by the canal route in the Dunnellon area. Over most of this area the Floridan aquifer is unconfined and receives direct recharge through a cover of a few tens of feet of sand and clayey sand of Quaternary age. Tensional stresses during the structural evolution of the Ocala Uplift produced an intersecting system of fractures and normal faults in rocks of the Floridan aquifer. The fractures and faults are important controls for orientation of solution channels and, therefore, for development of ground-water circulation patterns. When the system surface streams, which once drained the Barge Canal area, eroded the poorly permeable Miocene-Pliocene(?) cover from the flanks of the Ocala Uplift, surface runoff was reduced and precipitation began to directly infiltrate the underlying limestones. Now only principal streams remain, such as the Oklawaha and Withlacoochee Rivers and a few short tributaries, while one of the most highly developed subsurface drainage systems in the world has evolved in cavernous limestone of the Floridan aquifer. Two of the larger freshwater springs in the world now discharge from the Floridan aquifer in the canal area. Silver Springs near Ocala discharges an average 531 mgd (million gallons per day) down the 4-mile long Silver River, which flows on poorly permeable beds to the Oklawaha River. Rainbow Springs near Dunnellon discharges on average 468 mgd from numerous orifices in the bed of the 5-mile-long Rainbow River, which flows into the Withlacoochee River. The heads of the springs have migrated to their present positions partly because of a tendency of ground-water levels to decline as permeability in the aquifer is increased due to removal of limestone by solution, and because of mechanical erosion of the limestone in the vicinity of the spring heads. Also, points of principal spring discharges have shifted in the past due to changes in ground-water levels in response to changes in sea level. The subsurface drainage system is continuing to evolve today, as evidenced in part by frequent occurrence of new sinkholes and by the presence of significant amounts of calcium bicarbonate in the spring waters. Rodman Pool, at the east end of the canal, is separated from the Floridan aquifer by poorly permeable materials. The pool's operating water level will be only a few feet above the potentiometric surface at the downstream end, and at or slightly below the potentiometric surface at the upstream end. Little exchange of water between the Rodman Pool and the Floridan aquifer is expected. Eureka Pool, just upstream from Rodman Pool, will also be separated from the Floridan aquifer by poorly permeable beds. However, the stage of the pool will be about 15 feet higher than the natural potentiometric surface at the pool's downstream end, and some seepage into the Floridan aquifer is anticipated through faults and leaky parts of the poorly permeable beds, with a consequent rise in ground-water levels in areas adjacent to the lower end of the pool. Possibilities for particulate contamination of the aquifer will tend to be minimized because of the filtering capacity of the materials through which water must pass to reach the aquifer, although the natural filter will not preclude movement into the aquifer of contaminants which might become dissolved in the pool waters. No significant interchange of water between the pool and the aquifer is expected at the upstream end of the Eureka Pool. Present construction plans indicate an operating stage for Eureka Pool which will range between 38 and 40 feet above mean sea level, although it is possible to dredge the pool deep enough to permit a range in stage of 36 to 40 feet. A backwater effect extending up Silver River from the Eureka Pool is expected to regulate the stage at the head of Silver Springs between 39 and 44 feet above mean sea level if the pool ranges between 36 and 40 feet. If Eureka Pool ranges only between 38 and 40 feet, the range of stage at the head of the springs should be about 41 to 44 feet above mean sea level. From Inglis Lock west, the canal will have direct connection with the Gulf, and canal stage will fluctuate with the Gulf tide. Since the canal stage will be slightly lower than the adjacent ground-water levels along much of the reach, there will be some ground-water inflow to the canal. No significant changes in the existing ground-water regime are expected in the vicinity of Inglis Pool, the first step up in the canal east of the Gulf. Existing ground-water and surface-water levels in the area will not change appreciable, and the natural stage and flow of Rainbow Springs, which will flow by way of Rainbow River into Inglis Pool, should not be affected by canal operations. A possible adverse effect of the canal on the Inglis Pool area could result if sea water is locked up from the Gulf through Inglis Lock. However, the high step of 25 feet at the lock, flushing action of continuous flow from Inglis Pool to the lower reaches of the Withlacoochee River, and use of possible preventive locking procedures should minimize the problem. The potential for adverse effects on the ground-water regime is greatest in the area of the Summit Pool. Through most of the length of the pool, the canal channel will be excavated into limestone of the Floridan aquifer to depths of 12 to 27 feet below the potentiometric surface. Changes that will take place in the ground-water flow system in the Silver Springs drainage area, once the canal is completed, were estimated by flow-net analysis. Variation in aquifer transmissivity was determined by calculating transmissivity in 25 different flow cells surrounding Silver Springs. Transmissivity in the 25 cells averages about 15,600,000 gpd/ft [2,090,000 ft2/day (feet squared)], but transmissivity in the six cells through which the Summit Pool passes ranges from 9,000,000 to 44,000,000 gpd/ft (1,210,000 to 5,900,000 ft2/day). Transmissivity was used to compute static stage of the Summit Pool under given ground-water level conditions. Had the canal existed in May 1968 and had the stage of Eureka Pool been held at 36 feet at the time, the static stage in Summit Pool would have been about 42.1 feet above mean sea level. Thus, a conceptual model of the changes in the potentiometric surface wrought by the finished canal was drawn, and zones of ground-water inflow and outflow were delineated. Most outflow from the Summit Pool to the aquifer should be limited to one 4-mile-long zone along the north side of the pool, about 5 miles south of Silver Springs. It is estimated that a water volume equivalent to about 8 percent of the daily flow of Silver Springs will enter the Summit Pool each day from the southern one-third of the Silver Springs drainage area. A like amount will reenter the aquifer at the main zone of outflow and move toward Silver Springs at an estimated average velocity of about 200 feet per day, if something close to the natural static stage of the pool is maintained by return pumpage of the lockage losses. At a velocity of 200 feet per day, water from the Summit Pool would discharge at Silver Springs about 140 days later. However, any estimate of velocity in the highly cavernous limestone aquifer in the area should be used with caution, because difficult to measure changes in porosity and thickness of major zones of flow may cause large variations in velocity. If all lockage losses are returned to the Summit Pool by pumping from Eureka Pool, no net loss from the Silver Springs drainage area, except for some evaporation from the water surface in the canal and possible leakage around locks, will result from canal operations. The zone of outflow from the Summit Pool to the aquifer will be in a natural potentiometric trough, and the zone of inflow will be in a potentiometric ridge area. The equilibrium water level in the pool will tend to be about 1 foot higher than the altitude of the lowest level in the pre-canal potentiometric trough, and about 2 feet lower than the highest level on the pre-canal potentiometric ridge. West of the Silver Springs drainage area just east of Dunnellon Lock, in the area of a local potentiometric high, the water level in the Summit Pool is expected to be about 15 feet below the natural potentiometric surface. In most areas 2 to 3 miles away from the Summit Pool, effects of the canal on the natural potentiometric surface should be slight. The stage of the Summit Pool, judging from the 36-year record for ground-water level changes and the anticipated indirect effect of the controlled stage in Eureka Pool, should have a maximum of about 10.5 feet with a maximum water level of about 51.5 feet above mean sea level and a minimum of about 41.0 feet above mean sea level. Of particular importance in the Summit Pool is an implementation of well planned construction and operational procedures designed to minimize risks of ground-water contamination.

Florida↗

USGS2025

Land-based nutrient flux to a fringing reef: Insights from Ofu Island, American Samoa

Submarine groundwater discharge (SGD) is a critical driver of nutrient transport in coral reef ecosystems, shaping water quality, primary productivity, and overall reef health. This study quantifies SGD fluxes and associated nutrient dynamics in two reef flat pools within the Ofu Unit of the National Park of American Samoa: Papaloloa and Fatuana. A multi-method approach integrating unoccupied aerial system-based thermal infrared (UAS-TIR) surveys, radon-based SGD measurements, multichannel electrical resistivity tomography (ERT), and discrete water sampling was used to assess SGD rates and nutrient contributions. UAS-TIR imagery revealed cooler sea surface temperatures in both pools, indicative of SGD, with the higher fluxes observed in Papaloloa. Radon measurements revealed a strong inverse correlation between SGD rates and tidal stage, with a more immediate SGD response at Papaloloa due to its highly permeable calcareous sand and gravel substrate. In contrast, a 2–3-hour lag in SGD response at Fatuana suggests discharge from a more inland aquifer that has lower diffusivity. Nutrient concentrations correlated with temperature and salinity, confirming SGD as the dominant nutrient transport mechanism, whereas isotopic analyses indicated inputs from both groundwater and potential anthropogenic sources. Despite lower SGD flux at Fatuana, higher algal cover suggests additional factors influencing algal proliferation, including substrate availability and hydrodynamic conditions. Excess nutrient inputs from SGD may contribute to algal overgrowth, which threatens Ofu’s thermally tolerant corals by increasing competition for space and light. These findings underscore the complexity of SGD-mediated nutrient dynamics in reef environments and emphasize the need for integrated hydrological and ecological assessments to support effective reef conservation and management strategies.

American Samoa, Ofu Island, Olosega Island↗

USGS2025

Salinas Valley integrated hydrologic and reservoir operations models, Monterey and San Luis Obispo Counties, California

The area surrounding the Salinas Valley groundwater basin in Monterey and San Luis Obispo Counties of California is a highly productive agricultural area, contributes significantly to the local economy, and provides a substantial portion of vegetables and other agricultural commodities to the Nation. This region of California provides about half of the Nation’s lettuce, celery, broccoli, and spinach each year. Thus, this agricultural area provides significant volumes of agricultural products not just for California but the entire United States. Changes in population and increased agricultural development, which includes a shift toward more water-intensive crops, and climate variability, have put increasing demand on both surface water and groundwater resources in the valley. This has resulted in water management challenges in the Salinas Valley that are predominantly related to distribution of water supply throughout the basin. Where and when the water is present in the surface and subsurface does not coincide with where and when the water is needed. To deal with the distribution issue, historically water has been used conjunctively in the valley. Conjunctive use is a water management strategy that coordinates surface water and groundwater use to maximize water availability. Groundwater is used throughout the Salinas Valley to meet water demands when surface water supplies are insufficient. Availability of surface water is constrained by climate. Precipitation and streamflow vary seasonally and year to year. Although there are two reservoirs in the Salinas Valley to capture and store water during wet periods, the only conveyance of reservoir water to coastal agricultural areas is the Salinas River. Increasing demand on groundwater and surface water resources throughout the Salinas Valley has resulted in undesirable effects of unsustainable water use, such as surface water depletion, groundwater level declines, storage depletion in the principal aquifers, and seawater intrusion. To address these escalating issues, local communities, water management agencies, and groundwater sustainability agencies are evaluating how to sustainably manage both their surface water and groundwater resources. To meet water demands and reduce undesirable effects of unsustainable water use, continued conjunctive management of surface water and groundwater would ideally incorporate strategies to deal with increases in demand and a variable climate. To evaluate the challenging water management issues in the Salinas Valley, the U.S. Geological Survey, Monterey County Water Resource Agency, and the Salinas Valley Basin Groundwater Sustainability Agency developed a comprehensive suite of models that represent the Salinas Valley Hydrogeologic system called the Salinas Valley System Model. The Salinas Valley Geologic Framework was developed to characterize the subsurface using various topographic and geologic data sources, including information on hydrogeologic units, their surfaces and extents, geologic structures, lithology, and elevations from borehole data and cross sections, as well as details on faults and existing models. The Salinas Valley Watershed Model simulates the entire Salinas River watershed. Monthly surface water inflows into the integrated hydrologic model domain were simulated using the Salinas Valley Watershed Model. The historical model uses historical climate data, water and land use data, and reservoir releases to simulate agricultural operations, including landscape water demands, diversions, and reclaimed wastewater. The operational model adds an embedded reservoir operations framework to the simulation of the historical model that allows specified operational rules to simulate reservoir releases and changes in reservoir storage. The operational model assumes current reservoir operations and constant land use, which differs from historical conditions. Thus, the operational model is a hypothetical baseline model that can be used by local water managers to evaluate and quantify potential benefits of water supply projects. Together, the geologic framework, watershed, historical, and operational models form a tool that can be used to simulate irrigated agriculture and associated reservoir operations of the integrated hydrologic system of the Salinas Valley.

EarthArXiv↗

USGS2024

Hydrologic investigations and a preliminary conceptual model of the groundwater system at North Penn Area 1 Superfund Site, Souderton, Montgomery County, Pennsylvania

The U.S. Geological Survey (USGS) conducted hydrogeologic investigations, reviewed existing data, and developed a preliminary conceptual model of the groundwater system as part of technical support of the U.S. Environmental Protection Agency (EPA) at the North Penn Area 1 Superfund Site (hereafter, the NP1 Site) located within the Borough of Souderton in Montgomery County, Pennsylvania. Field work and monitoring took place during 2012–18. The area is underlain by sedimentary formations that form a fractured-rock aquifer used for drinking water and industrial supply. The EPA placed the Site on the National Priorities List in 1989, identifying tetrachloroethylene (PCE) and trichloroethylene (TCE) as contaminants of concern. During 2012–18, the USGS conducted field activities that included drilling an 82-foot (ft)-deep monitoring well (MG 2220) in 2016, reconstructing a 208-ft-deep former industrial production well (MG 668 [Granite Knitting Mill]), and collecting borehole geophysical and video logs and water levels from those and five additional wells, which ranged in depth from about 50 to 200 ft below land surface. Continuous water levels were collected during 2014–17, and a synoptic set of water levels were measured in April 2018 in the seven wells. The borehole geophysical logs (caliper, acoustic televiewer, natural gamma, single-point resistance, vertical flow, and fluid temperature and resistivity) and borehole video logs in the seven wells were evaluated to assess potential for lithologic correlation and to identify and describe water-bearing features, which included both low- and high-angle fractures and other openings oriented along dipping bedding planes, joints, or possible faults. Borehole geophysical logs collected by USGS in 1992 in a 300-ft-deep former production well near the Site were also evaluated. Few to no distinctive features were identified on geophysical logs (natural gamma and single-point resistance) that could be used for correlation, thus limiting this approach to determining local geologic structure. Extensive fracturing in the upper 62 ft of monitoring well MG 2220 indicates that the well was likely drilled through a zone of faulting, and other evidence of faulting is present in the area near the Site. Assessment of continuous water levels showed hydraulic connections among some wells as indicated by rising or falling water levels in response to changes in pumping rates at nearby wells. A map of water levels measured in April 2018 indicates potential for groundwater flow generally toward the stream to the south and southwest of the Site, but the limited water-level data are insufficient to describe vertical groundwater gradients or lateral gradients in any detail. Review of 1999–2022 volatile organic compound (VOC) monitoring data collected by the Pennsylvania Department of Environmental Protection for five monitoring wells indicates that the highest groundwater concentrations of PCE and TCE were found in samples from extraction well MG 2201 (S-1) downgradient from, and nearest to, the previously identified Site contaminant source area, and these concentrations fluctuated through time. PCE concentrations were higher than TCE concentrations in samples from all five monitoring wells and were much higher than TCE concentrations in samples from extraction well MG 2201 (S-1). Temporally variable recharge is a possible factor affecting observed fluctuations in PCE concentrations in groundwater samples from well extraction MG 2201 (S-1), as indicated by a general inverse relation between PCE concentrations and water levels in a nearby long-term observation well. The PCE concentration of 1,830 micrograms per liter (μg/L) in a May 2018 water sample from monitoring well MG 2220 was more than four times the PCE concentration of 444 μg/L in a December 2017 sample from the nearby extraction well MG 2201 (S-1), which is open to fewer fractures. Low concentrations of VOCs were measured in surface water at two stream sites downgradient from wells with the highest groundwater VOC concentrations at the Site, indicating that discharge of contaminated groundwater to the stream is likely. Development of a conceptual model of the groundwater system was constrained by limited data. In areas with no pumping, groundwater-flow directions generally are thought to be controlled by topography and geologic structure (bedding orientation) and likely to the south and southwest of the Site, with local flow directions affected by orientations of fractures, joints, and local faults. Additional investigations that could help improve the conceptual model of the groundwater system and help delineate the extent of groundwater contamination and its transport are discussed.

Pennsylvania↗