Search USGS⌕ Search

USGS · wri731

Geohydrology of the Cross-Florida Barge Canal area, with special reference to the Ocala vicinity

Abstract

The Cross-Florida Barge Canal route commences at Palatka on the St. Johns River, about 75 miles upstream from the Atlantic Ocean, and extends 110 miles southwestward across Peninsular Florida into deep water in the Gulf of Mexico near Yankeetown. The canal will be equipped with five locks, each 600 feet long and 84 feet wide, and the channel will be a minimum of 12 feet deep and 150 feet wide. From near Ocala northeastward, the canal channel will replace much of the natural channel of the Oklawaha River, and will be excavated into beds of the so-called shallow sand aquifer of Miocene age and younger, which overlies limestone of the Floridan aquifer. Westward from Ocala, most of the canal will be excavated below the potentiometric surface into limestone and dolomite of the Floridan aquifer. Water levels of Rodman, Eureka, and Inglis Pools will be controlled by dams and spillways with the limited exchange of water between the pools and the aquifers. The water levels in the Summit Pools will fluctuate with the natural changes in the ground-water level of the Floridan aquifer, although the stage of the pool will be controlled partly by the stage held in the Eureka Pool. A dynamic inflow-outflow relationship will exist between the Summit Pool and the Floridan aquifer. The Floridan aquifer in the canal area is 1,000 to 1,200 feet thick and consists of limestone and dolomite of middle Eocene Miocene age, including from older to younger, the Lake City, Avon Park, and Ocala limestones plus permeable sandy, dolomitic limestone in the lower part of the Hawthorn Formation. It is possible that most of the flow to the two major springs in the area occurs in the upper 100 feet or so of the aquifer in the Ocala Limestone. The aquifer is underlain by the Oldsmar limestone of early Eocene age and is overlain by sand, clayey sand, clay and shell beds of Miocene through Holocene age, in thickness from a few feet to 300 feet. The permeable beds overlying the Floridan aquifer constitute the shallow aquifer, while the poorly permeable ones act as confining beds where the Floridan aquifer is under artesian conditions. A north-south line drawn separating the head of Silver Springs on the west from the Oklawaha River on the east marks the approximate western limit of a continuous blanket of materials of Miocene-Pliocene(?) age covering the rocks of the Floridan aquifer. East of the line, much of the aquifer is under artesian conditions, particularly in the Oklawaha River valley, although in some areas east of the valley, direct recharge through thick permeable Miocene-Pliocene(?) sands occurs. West of the line, only scattered remnants of a once continuous Miocene-Pliocene(?) cover remain. Lack of the cover is a result of erosion on the crest and flank of the Ocala Uplift, a broad northwest-southeast trending anticlinal upwarp, the axis of which is crossed by the canal route in the Dunnellon area. Over most of this area the Floridan aquifer is unconfined and receives direct recharge through a cover of a few tens of feet of sand and clayey sand of Quaternary age. Tensional stresses during the structural evolution of the Ocala Uplift produced an intersecting system of fractures and normal faults in rocks of the Floridan aquifer. The fractures and faults are important controls for orientation of solution channels and, therefore, for development of ground-water circulation patterns. When the system surface streams, which once drained the Barge Canal area, eroded the poorly permeable Miocene-Pliocene(?) cover from the flanks of the Ocala Uplift, surface runoff was reduced and precipitation began to directly infiltrate the underlying limestones. Now only principal streams remain, such as the Oklawaha and Withlacoochee Rivers and a few short tributaries, while one of the most highly developed subsurface drainage systems in the world has evolved in cavernous limestone of the Floridan aquifer. Two of the larger freshwater springs in the world now discharge from the Floridan aquifer in the canal area. Silver Springs near Ocala discharges an average 531 mgd (million gallons per day) down the 4-mile long Silver River, which flows on poorly permeable beds to the Oklawaha River. Rainbow Springs near Dunnellon discharges on average 468 mgd from numerous orifices in the bed of the 5-mile-long Rainbow River, which flows into the Withlacoochee River. The heads of the springs have migrated to their present positions partly because of a tendency of ground-water levels to decline as permeability in the aquifer is increased due to removal of limestone by solution, and because of mechanical erosion of the limestone in the vicinity of the spring heads. Also, points of principal spring discharges have shifted in the past due to changes in ground-water levels in response to changes in sea level. The subsurface drainage system is continuing to evolve today, as evidenced in part by frequent occurrence of new sinkholes and by the presence of significant amounts of calcium bicarbonate in the spring waters. Rodman Pool, at the east end of the canal, is separated from the Floridan aquifer by poorly permeable materials. The pool's operating water level will be only a few feet above the potentiometric surface at the downstream end, and at or slightly below the potentiometric surface at the upstream end. Little exchange of water between the Rodman Pool and the Floridan aquifer is expected. Eureka Pool, just upstream from Rodman Pool, will also be separated from the Floridan aquifer by poorly permeable beds. However, the stage of the pool will be about 15 feet higher than the natural potentiometric surface at the pool's downstream end, and some seepage into the Floridan aquifer is anticipated through faults and leaky parts of the poorly permeable beds, with a consequent rise in ground-water levels in areas adjacent to the lower end of the pool. Possibilities for particulate contamination of the aquifer will tend to be minimized because of the filtering capacity of the materials through which water must pass to reach the aquifer, although the natural filter will not preclude movement into the aquifer of contaminants which might become dissolved in the pool waters. No significant interchange of water between the pool and the aquifer is expected at the upstream end of the Eureka Pool. Present construction plans indicate an operating stage for Eureka Pool which will range between 38 and 40 feet above mean sea level, although it is possible to dredge the pool deep enough to permit a range in stage of 36 to 40 feet. A backwater effect extending up Silver River from the Eureka Pool is expected to regulate the stage at the head of Silver Springs between 39 and 44 feet above mean sea level if the pool ranges between 36 and 40 feet. If Eureka Pool ranges only between 38 and 40 feet, the range of stage at the head of the springs should be about 41 to 44 feet above mean sea level. From Inglis Lock west, the canal will have direct connection with the Gulf, and canal stage will fluctuate with the Gulf tide. Since the canal stage will be slightly lower than the adjacent ground-water levels along much of the reach, there will be some ground-water inflow to the canal. No significant changes in the existing ground-water regime are expected in the vicinity of Inglis Pool, the first step up in the canal east of the Gulf. Existing ground-water and surface-water levels in the area will not change appreciable, and the natural stage and flow of Rainbow Springs, which will flow by way of Rainbow River into Inglis Pool, should not be affected by canal operations. A possible adverse effect of the canal on the Inglis Pool area could result if sea water is locked up from the Gulf through Inglis Lock. However, the high step of 25 feet at the lock, flushing action of continuous flow from Inglis Pool to the lower reaches of the Withlacoochee River, and use of possible preventive locking procedures should minimize the problem. The potential for adverse effects on the ground-water regime is greatest in the area of the Summit Pool. Through most of the length of the pool, the canal channel will be excavated into limestone of the Floridan aquifer to depths of 12 to 27 feet below the potentiometric surface. Changes that will take place in the ground-water flow system in the Silver Springs drainage area, once the canal is completed, were estimated by flow-net analysis. Variation in aquifer transmissivity was determined by calculating transmissivity in 25 different flow cells surrounding Silver Springs. Transmissivity in the 25 cells averages about 15,600,000 gpd/ft [2,090,000 ft2/day (feet squared)], but transmissivity in the six cells through which the Summit Pool passes ranges from 9,000,000 to 44,000,000 gpd/ft (1,210,000 to 5,900,000 ft2/day). Transmissivity was used to compute static stage of the Summit Pool under given ground-water level conditions. Had the canal existed in May 1968 and had the stage of Eureka Pool been held at 36 feet at the time, the static stage in Summit Pool would have been about 42.1 feet above mean sea level. Thus, a conceptual model of the changes in the potentiometric surface wrought by the finished canal was drawn, and zones of ground-water inflow and outflow were delineated. Most outflow from the Summit Pool to the aquifer should be limited to one 4-mile-long zone along the north side of the pool, about 5 miles south of Silver Springs. It is estimated that a water volume equivalent to about 8 percent of the daily flow of Silver Springs will enter the Summit Pool each day from the southern one-third of the Silver Springs drainage area. A like amount will reenter the aquifer at the main zone of outflow and move toward Silver Springs at an estimated average velocity of about 200 feet per day, if something close to the natural static stage of the pool is maintained by return pumpage of the lockage losses. At a velocity of 200 feet per day, water from the Summit Pool would discharge at Silver Springs about 140 days later. However, any estimate of velocity in the highly cavernous limestone aquifer in the area should be used with caution, because difficult to measure changes in porosity and thickness of major zones of flow may cause large variations in velocity. If all lockage losses are returned to the Summit Pool by pumping from Eureka Pool, no net loss from the Silver Springs drainage area, except for some evaporation from the water surface in the canal and possible leakage around locks, will result from canal operations. The zone of outflow from the Summit Pool to the aquifer will be in a natural potentiometric trough, and the zone of inflow will be in a potentiometric ridge area. The equilibrium water level in the pool will tend to be about 1 foot higher than the altitude of the lowest level in the pre-canal potentiometric trough, and about 2 feet lower than the highest level on the pre-canal potentiometric ridge. West of the Silver Springs drainage area just east of Dunnellon Lock, in the area of a local potentiometric high, the water level in the Summit Pool is expected to be about 15 feet below the natural potentiometric surface. In most areas 2 to 3 miles away from the Summit Pool, effects of the canal on the natural potentiometric surface should be slight. The stage of the Summit Pool, judging from the 36-year record for ground-water level changes and the anticipated indirect effect of the controlled stage in Eureka Pool, should have a maximum of about 10.5 feet with a maximum water level of about 51.5 feet above mean sea level and a minimum of about 41.0 feet above mean sea level. Of particular importance in the Summit Pool is an implementation of well planned construction and operational procedures designed to minimize risks of ground-water contamination.

Explore related subjects

90° N90° S · 180° W ← longitude → 180° E
Source-reported bounding extent: 26.9446464° to 30.8448798° latitude; -84.9454638° to -80.2970544309211° longitude. This indicates report coverage, not an exact sampling location. View area on OpenStreetMap.

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

Glen L. Faulkner. 1973. Geohydrology of the Cross-Florida Barge Canal area, with special reference to the Ocala vicinity. https://doi.org/10.3133/wri731

Cite the original work for its findings. Save a collection to share your selection of sources.

Discover connections

Connections use source metadata and explicit phrase matches, not verified experimental comparisons.

KEEP EXPLORING

Related USGS reports

Hydrogeology of the Tully Valley and characterization of mudboil activity, Onondaga County, New York

Mudboil activity in the Tully Valley, in central New York, is causing turbidity in nearby Onondaga Creek, where it has caused a bridge to collapse; it also has threatened or damaged other structures and has caused extensive land subsidence. Mudboil activity was intermittent from its first reported appearance in the 1890's until the 1970's, when the rates of mudboil discharge and land subsidence began to increase. Historically, the water discharged from mudboils was reported as fresh, but chemical analyses in the late 1970's indicated an increase in specific conductance and chloride concentration. Mudboil discharge is driven by artesian pressure in unconsolidated sediments that are confined by a 60-foot layer of silt and red clay. This process, once begun, has been self-propagating. Artesian pressures are about 20 feet above land surface over most of the valley floor but exceed 30 feet above land surface along Onondaga Creek where Rattlesnake Gulf and Rainbow Creek enter the Tully Valley. The source of artesian pressure is recharge from the Tully (Valley Heads) Moraine at the south end of the valley, and the alluvial fans of Rattlesnake Gulf and Rainbow Creek. The mudboils are found within a 300-foot-wide by 1,500-foot-long corridor along Onondaga Creek just upstream from the two alluvial fans, and in a 5-acre subsided area just west of that corridor. Remediation efforts have entailed (1) diversion of flow from the tributary that feeds the subsided area, (2) installation of depressurizing wells at several locations, and (3) construction of a dam and settling impoundment to detain mudboil sediment that would normally discharge to Onondaga Creek. These efforts have been partly successful, but further work is needed to slow the mudboil activity, which is expected to persist in both areas. Mudboil activity is normally greatest during the early spring and late fall, when artesian pressures increase in response to seasonal ground-water recharge. Suspended-sediment concentrations at the out-flow of the subsidence area ranged from 31,210 mg/L (milligrams per liter) in October 1991 to 17 mg/L after remediation efforts in the summer of 1993. Yearly average suspended-sediment loads to Onondaga Creek from the subsidence area for water years 1992, 1993, 1994, and 1995 were 29.8, 9.75, 1.41, and 1.80 tons per day, respectively. Sediment discharged from the mudboils initially was 30 to 60 percent clay and 80 to 100 percent silt-sized or smaller sediment, and the sand fraction never exceeded 20 percent. After the remediation projects, 50 to 80 percent was clay, and nearly all sediment was silt size or smaller. Analyses of water from upstream and downstream of the subsidence area, as well as from mudboil vents within that area, indicate that the source of water for some mudboils is a confined freshwater aquifer, whereas for others it is an underlying, brackish-water aquifer. Water from the freshwater aquifer has specific conductance values ranging from about 400 ( μS /cm (microsiemens per centimeter at 25° Celsius) to almost 900 ( μS /cm, dissolved chloride concentrations range from 37 to 430 mg/L, and dissolved-solids concentrations range from 215 to 463 mg/L. Specific conductance of water from the brackish-water aquifer ranges from 17,000 to 28,000 ( μS /cm, chloride concentrations range from 2,000 to 7,100 mg/L, and dissolved-solids concentrations range from 4,200 to 12,800 mg/L. The largest landslide in New York State in the last 75 years occurred at the foot of Bare Mountain, 1 mile downstream from the mudboil area, in April 1993 and was the fourth in a series of slides that have occurred at the base of this hill. Slope instability was reported as early as May 1990. After the slide, intermittent mudboil-like activity was observed at several springs within the backscarp of the slide; water from these springs ranged from fresh to brackish. The chemical similarity between water from some springs in the backscarp area and water in the lower (brackish) aquifer beneath the mudboil area may indicate a hydraulic connection between this aquifer and the surficial deposits. Hydrologic changes in the valley during the last 100 years have been attributed to salt-solution mining in the upstream (southern) end of the valley. The removal of nearly 150 feet of salt from four evaporite beds in the Syracuse Shale of the Salina Group has caused the collapse of bedrock and unconsolidated deposits in and near the brine field, 3 miles south of the mudboil area. These collapses have created a hydraulic connection among bedding plane aquifers in the bedrock and increased the hydraulic connection with unconsolidated aquifers. The ground-water flow system after brine field closure in 1988 may have reached a new semiequilibrium, but mudboil activity will likely continue because artesian pressures remain. Whether mudboils were present before salt solution-mining began is unknown.

New York↗

Evaluation of the Source and Transport of High Nitrate Concentrations in Ground Water, Warren Subbasin, California

Ground water historically has been the sole source of water supply for the Town of Yucca Valley in the Warren subbasin of the Morongo ground-water basin, California. An imbalance between ground-water recharge and pumpage caused ground-water levels in the subbasin to decline by as much as 300 feet from the late 1940s through 1994. In response, the local water district, Hi-Desert Water District, instituted an artificial recharge program in February 1995 using imported surface water to replenish the ground water. The artificial recharge program resulted in water-level recoveries of as much as 250 feet in the vicinity of the recharge ponds between February 1995 and December 2001; however, nitrate concentrations in some wells also increased from a background concentration of 10 milligrams per liter to more than the U.S. Environmental Protection Agency (USEPA) maximum contaminant level (MCL) of 44 milligrams per liter (10 milligrams per liter as nitrogen). The objectives of this study were to: (1) evaluate the sources of the high-nitrate concentrations that occurred after the start of the artificial-recharge program, (2) develop a ground-water flow and solute-transport model to better understand the source and transport of nitrates in the aquifer system, and (3) utilize the calibrated models to evaluate the possible effect of a proposed conjunctive-use project. These objectives were accomplished by collecting water-level and water-quality data for the subbasin and assessing changes that have occurred since artificial recharge began. Collected data were used to calibrate the ground-water flow and solute-transport models. Data collected for this study indicate that the areal extent of the water-bearing deposits is much smaller (about 5.5 square miles versus 19 square miles) than that of the subbasin. These water-bearing deposits are referred to in this report as the Warren ground-water basin. Faults separate the ground-water basin into five hydrogeologic units: the west, the midwest, the mideast, the east and the northeast hydrogeologic units. Water-quality analyses indicate that septage from septic tanks is the primary source of the high-nitrate concentrations measured in the Warren ground-water basin. Water-quality and stable-isotope data, collected after the start of the artificial recharge program, indicate that mixing occurs between imported water and native ground water, with the highest recorded nitrate concentrations in the midwest and the mideast hydrogeologic units. In general, the timing of the increase in measured nitrate concentrations in the midwest hydrogeologic unit is directly related to the distance of the monitoring well from a recharge site, indicating that the increase in nitrate concentrations is related to the artificial recharge program. Nitrate-to-chloride and nitrogen-isotope data indicate that septage is the source of the measured increase in nitrate concentrations in the midwest and the mideast hydrogeologic units. Samples from four wells in the Warren ground-water basin were analyzed for caffeine and selected human pharmaceutical products; these analyses suggest that septage is reaching the water table. There are two possible conceptual models that explain how high-nitrate septage reaches the water table: (1) the continued downward migration of septage through the unsaturated zone to the water table and (2) rising water levels, a result of the artificial recharge program, entraining septage in the unsaturated zone. The observations that nitrate concentrations increase in ground-water samples from wells soon after the start of the artificial recharge program in 1995 and that the largest increase in nitrate concentrations occur in the midwest and mideast hydrogeologic units where the largest increase in water levels occur indicate the validity of the second conceptual model (rising water levels). The potential nitrate concentration resulting from a water-level rise in the midwest and mideast hydrogeologic units was estimated using a simple mixing-cell model. The estimated value is within the range of concentrations measured in samples from wells, further indicating the validity of the second conceptual model. A ground-water flow model and a solute-transport model were developed for the Warren ground-water basin for the period 1956-2001. MODFLOW-96 was used for the ground-water flow model and MOC3D was used for the solute-transport model. The model cell size is about 500 feet by 500 feet and the models were discretized vertically into three layers. The models were calibrated using a trial-and-error approach using water-level and nitrate-concentration data collected between 1956-2001. In order to better match the measured data, low fault hydraulic characteristic values were required, thereby compartmentalizing the ground-water basin. In addition, it was necessary to parameterize the specific yield distribution for the top model layer where unconfined ground-water conditions occur into three homogeneous zones. Separate sets of specific- yield values were needed to simulate the drawdown and subsequent water-level recovery. In addition, the calibrated natural recharge was about 83 acre-feet per year. The entrainment of unsaturated-zone septage was simulated as recharge having an associated nitrate concentration. The volume of recharge was a function of the measured water-level rise between 1994-98 and the moisture content of the unsaturated zone. The nitrate concentration of the recharge water was a weighted function of the assumed nitrate concentration in the infiltrating water associated with the overlying land use. The simulated hydraulic head and nitrate concentration results were in good agreement with the measured data indicating that the mechanism for the increase in nitrate concentrations was rising water levels entraining high-nitrate septage in the unsaturated-zone. The calibrated models were used to simulate the possible effects of a planned conjunctive-use project in the western part of the ground-water basin. The simulated project included the addition of a new recharge pond and a new extraction well. In addition, recharge at two existing recharge ponds was increased and three existing production wells were pumped, treated in a nitrate-removal facility, and used for water supply. The simulated hydraulic heads increased in the west, the mideast, and parts of the east hydrogeologic units; however, the simulated hydraulic heads decreased in the midwest and northeast hydrogeologic units. The simulated nitrate concentrations increased to above the MCL of 44 milligrams per liter (10 milligrams per liter as nitrogen) in parts of the west as a result of the increase in simulated hydraulic head. The simulated nitrate concentrations decreased in part of the midwest hydrogeologic unit as a result of the artificial recharge and pumping from the nitrate-removal wells. The simulated nitrate concentrations increased to above the MCL of 44 milligrams per liter in part of the mideast and parts of the east hydrogeologic units beneath commercial land-use areas.

California↗

Clear-water abutment and contraction scour in the Coastal Plain and Piedmont Provinces of South Carolina, 1996-99

The U.S. Geological Survey, in cooperation with the South Carolina Department of Transportation, collected observations of clear-water aburment and contraction scour at 146 bridges in the Coastal Plain and Piedmont of South Carolina. Scour depths ranged from 0 to 23.6 feet. Theoretical scour depths were computed at each bridge and compared with observed scour. This comparison showed that theoretical scour depths, in general, exceeded the observed scour depths and often were excessive. A comparison of field data with dimensionless relations for laboratory data showed that the range of dimensionless variables used in laboratory investigations was outside of the range for field data in South Carolina, suggesting laboratory relations may not be applicable to field conditions in South Carolina. Variables determined to be important in developing scour within laboratory studies were investigated to understand their influence within the South Carolina field data, and many of these variables appeared to be insignificant under field conditions found in South Carolina. The strongest explanatory variables were embankment length, geometric-contraction ratio, approach velocity, and soil cohesion. Envelope curves developed with the field data are useful tools for assessing reasonable ranges of scour depth in South Carolina. These tools are simple to apply and are an improvement over the current methods for predicting theoretical scour. Data from this study have been compiled into a database that includes photographs, figures, observed scour depths, theoretical scour depths, limited basin characteristics, limited soil data, and theoretical hydraulic data. The database can be used to compare studied sites with unstudied sites to assess the potential for scour at the unstudied sites. In addition, the database can be used to assess the performance of various theoretical methods for predicting clear-water abutment and contraction scour.

South Carolina↗