Search USGS⌕ Search

Geology topics

John H. Williams

Publications and source records attributed to John H. Williams.

At least 37 records · Page 2Linked to original sources
USGS2019

Time-domain electromagnetic soundings for the delineation of saline groundwater in the Genesee River Valley, Western New York, 2016-2017

The U.S. Geological Survey, in cooperation with the New York State Department of Environmental Conservation, is investigating the distribution of saline groundwater in the Genesee River Valley near the former Retsof salt mine (fig. 1). As part of this study, paired time-domain electromagnetic (TEM) soundings and horizontal-to-vertical spectral ratio (HVSR) seismic soundings were made at 39 locations during the fall of 2016 to determine the presence of saline groundwater and depth to the bedrock surface, respectively. All measurement sites were west of Geneseo, New York, on the Genesee River valley floor north and south of the sinkhole area that developed as a result of the roof collapse and flooding of the Retsof mine in 1994 (fig. 1). An integrated analysis of the TEM and HVSR soundings with borehole logs, coupled with groundwater-sample data from previous investigations, allowed the delineation of zones of high electrical conductivity associated with saline water in the lower part of the valley fill and underlying bedrock to depths greater than 1,000 feet (ft). This article describes the TEM sounding method and its application in the ongoing investigation, presents results of the TEM analysis at two of the sounding sites, and identifies proposed sites for additional TEM/HVSR sounding data collection during the fall of 2017. Supporting data for this study are available in a separate data release (Johnson and others, 2017).

New York↗
USGS2018

Groundwater-level analysis of selected wells in the Hoosic River Valley near Hoosick Falls, New York, for aquifer framework and properties

The U.S. Geological Survey, in cooperation with the New York State Department of Environmental Conservation, analyzed groundwater levels, drilling record logs, and field water-quality data from selected wells, and the surficial geology in the Hoosic River valley south of the village of Hoosick Falls, New York, to provide information about the framework and properties of a confined aquifer. The aquifer, which consists of ice-contact sand and gravel overlain by lacustrine clay and silt, was evaluated by the New York State Department of Environmental Conservation as part of their investigation of alternate water supplies for the village whose wellfield has been affected by perfluorooctanoic acid. Wells inventoried in the study area were classified as confined, water table, or transitional between the two aquifer conditions. Groundwater levels in three confined-aquifer wells and a transitional-aquifer well responded to pumping of a test production well finished in the confined aquifer. Groundwater levels in a water-table well showed no detectable water-level change in response to test-well pumping. Analysis of drawdown and recovery data from the three confined-aquifer wells and a transitional-aquifer well through the application of the Theis type-curve method provided estimates of aquifer properties. Representation of a constant-head boundary in the analysis where an unnamed pond and fluvial-terrace deposits abut the valley wall resulted in satisfactory matches of the Theis type curves with the observed water-level responses. Aquifer transmissivity estimates ranged from 1,160 to 1,370 feet squared per day. Aquifer storativity estimates ranged from 5.2×10 –5 to 1.1×10 –3 and were consistent with the inferred degree of confinement and distance from the represented recharge boundary.

New York↗
USGS2017

Bioremediation in fractured rock: 1. Modeling to inform design, monitoring, and expectations

Field characterization of a trichloroethene (TCE) source area in fractured mudstones produced a detailed understanding of the geology, contaminant distribution in fractures and the rock matrix, and hydraulic and transport properties. Groundwater flow and chemical transport modeling that synthesized the field characterization information proved critical for designing bioremediation of the source area. The planned bioremediation involved injecting emulsified vegetable oil and bacteria to enhance the naturally occurring biodegradation of TCE. The flow and transport modeling showed that injection will spread amendments widely over a zone of lower‐permeability fractures, with long residence times expected because of small velocities after injection and sorption of emulsified vegetable oil onto solids. Amendments transported out of this zone will be diluted by groundwater flux from other areas, limiting bioremediation effectiveness downgradient. At nearby pumping wells, further dilution is expected to make bioremediation effects undetectable in the pumped water. The results emphasize that in fracture‐dominated flow regimes, the extent of injected amendments cannot be conceptualized using simple homogeneous models of groundwater flow commonly adopted to design injections in unconsolidated porous media (e.g., radial diverging or dipole flow regimes). Instead, it is important to synthesize site characterization information using a groundwater flow model that includes discrete features representing high‐ and low‐permeability fractures. This type of model accounts for the highly heterogeneous hydraulic conductivity and groundwater fluxes in fractured‐rock aquifers, and facilitates designing injection strategies that target specific volumes of the aquifer and maximize the distribution of amendments over these volumes.

Groundwater↗
USGS2015

Hydrogeology of the Owego-Apalachin Elementary School geothermal fields, Tioga County, New York

The hydrogeology of the Owego-Apalachin Elementary School geothermal fields, which penetrate saline water and methane in fractured upper Devonian age bedrock in the Owego Creek valley, south-central New York, was characterized through the analysis of drilling and geophysical logs, water-level monitoring data, and specific-depth water samples. Hydrogeologic insights gained during the study proved beneficial for the design of the geothermal drilling program and protection of the overlying aquifer during construction, and may be useful for the development of future geothermal fields and other energy-related activities, such as drilling for oil and natural gas in similar fractured-bedrock settings. The southwest geothermal field consists of 204 closed-loop wells that penetrate a major saline water-bearing zone associated with bedding-plane fractures near the middle of an interbedded sandstone and shale interval at depths of 238 to 263 feet below land surface (ft bls). The northeast geothermal field consists of 80 closed-loop wells that penetrate a major saline water-bearing zone associated with bedding-plane fractures near the base of the interbedded sandstone and shale interval at depths of 303 to 323 ft bls. Transmissivity estimates for the major saline water-bearing fractured zones range from 735 to 3,400 feet squared per day. The saline water-bearing zone in the southwest field is hydraulically connected over a horizontal distance of at least 350 feet. The hydraulic connection between subhorizontal, stacked bedding-plane fractures is limited by the number and transmissivity of interspersed higher angle fractures; locally, greater stratigraphic separation results in reduced connectivity to a greater degree than does horizontal distance. The specific conductance of the saline water from the shallower fractured zone in the southwest field was about 16,000 microsiemens per centimeter at 25 degrees Celsius (μS/cm at 25°C), and that from the fractured zone in the northeast field was about 65,000 μS/cm at 25°C. The saline waters were characterized by a chemical composition similar to that of deep formation brines collected from oil and gas wells in the Appalachian Basin. About 40 percent of the geothermal wells discharged methane gas to land surface during and (or) following drilling. Sandstone beds at depths of 348 to 378 ft bls are the likely source of the methane gas, which was determined to be early thermogenic in origin.

New York↗
USGS2015

Geophysical log analysis of selected test and residential wells at the Shenandoah Road National Superfund Site, East Fishkill, Dutchess County, New York

The U.S. Geological Survey collected and analyzed geophysical logs from 20 test wells and 23 residential wells at the Shenandoah Road National Superfund Site in East Fishkill, New York, from 2006 through 2010 as part of an Interagency Agreement to provide hydrogeologic technical support to the U.S. Environmental Protection Agency, Region 2. The geophysical logs collected include caliper, gamma, acoustic and optical televiewer, deviation, electromagnetic-induction, magnetic-susceptibility, fluid-property, and flow under ambient and pumped conditions. The geophysical logs were analyzed along with single-well aquifer test data and drilling logs to characterize the lithology, fabric, fractures, and flow zones penetrated by the wells. The results of the geophysical log analysis were used as part of the hydrogeologic characterization of the site and in the design of discrete-zone monitoring installations in the test wells and selected residential wells. Most of the logged test and residential wells penetrated gneiss of the Hudson Highlands Complex or dolostones in the Wappinger Group, and some wells penetrated both the dolostone and gneiss. The bedrock fabric reflects the regional northeast-southwest structural trend, as well as localized folding, and includes foliation in the gneiss and bedding in the dolostone. Many fractures were oriented along the bedrock fabric, whereas others were orthogonal to the fabric. Total wellbore transmissivity of the wells was estimated from short-term, single-well aquifer test data through the use of the Cooper-Jacob analytical solution. An empirical relation was established to estimate total wellbore transmissivity from specific-capacity data for wells with insufficient transient drawdown measurements. Wellbore transmissivity estimates ranged from 0.36 to 370 feet squared per day (ft 2 /d), whereas specific capacities ranged from 0.03 to 2.1 gallons per minute per foot ((gal/min)/ft). Transmissivity and hydraulic heads of individual fracture zones were estimated from the total wellbore transmissivity and flow logs through use of an analytical model based on the Thiem equation. The model-estimated transmissivity of 95 fracture zones delineated in the 43 wells ranged from 0.25 to 340 ft 2 /d, with a median value of 6.7 ft 2 /d. The difference between model-estimated fracture-zone heads and the composite heads in each well ranged from less 0.01 to more than 10 feet (ft). Flow-log analysis generally provided an order of magnitude estimate for the fracture-zone hydraulic-head difference on the basis of a comparison of estimated and measured values. The geophysical logs and their analyses are available for display and download from the U.S. Geological Survey, New York Water Science Center, online geophysical log archive ( http://ny.water.usgs.gov/maps/geologs/ ) in LAS (Log ASCII Standard), PDF, and WellCad formats.

New York↗
USGS2015

Geohydrologic and water-quality characterization of a fractured-bedrock test hole in an area of Marcellus shale gas development, Tioga County, Pennsylvania

An integrated analysis of core, geophysical logs, gas isotopes, and specific-depth water-quality samples from the Cherry Flats test hole was used to characterize the stratigraphy, water-bearing zones, and groundwater quality at a site in southern Tioga County, Pennsylvania. The study was completed as a cooperative effort between the Pennsylvania Department of Natural Resources, Bureau of Topographic and Geologic Survey (BTGS) and the U.S. Geological Survey (USGS). The multi-disciplinary characterization of the test hole provided information to aid the bedrock mapping of the Cherry Flats 7.5-minute quadrangle by BTGS, and to help quantify the depth and character of fresh and saline groundwater in an area of shale-gas exploration. The Cherry Flats test hole was cored to a depth of 1,513 feet (ft) below land surface (bls) and cased to 189 ft through the collapsed mine workings of the former Arnot No. 2 underground coal mine. The test hole penetrated 128.0 ft of Allegheny Formation and 154.1 ft of Pottsville Formation of Pennsylvanian age, 564.8 ft of Huntley Mountain Formation of Mississippian and Devonian age, and 666.3 ft of Catskill Formation of Devonian age. Core recovery was nearly 100 percent, except where complete core loss occurred from a depth of 1,231.1 to 1,240.8 ft. Several coal beds and mined-out coal horizons were penetrated in the Allegheny and Pottsville Formations. The test hole penetrated the entire thickness of the Huntley Mountain Formation and was completed in the middle part of the Catskill Formation. Bedding features penetrated by the test hole were estimated to have a strike of 021 degrees and dip about 1.7 degrees to the southeast, consistent with the test-hole location on the north limb of the Blossburg syncline. Most fractures penetrated by the test hole were parallel to bedding, with steeply dipping fractures present but much less common. Fracture density, determined from optical televiewer, acoustic televiewer, and video logs, generally increased with depth from the base of casing to about 400 ft bls, then decreased with depth to the bottom of the hole except for an increase from 506 to 568 ft bls. Very few fractures were penetrated from 600 to 850 ft. The depths of fresh and saline water-bearing zones were identified in the test hole by geophysical-log analysis and, for inflow zones, verified by specific-depth groundwater sampling by the use of a wire-line point sampler. Under ambient conditions and during pumping of the test hole, fresh water entered the hole from fractures at 567 and 580.5 ft bls, within grayish-red siltstone and greenish-gray sandstone, respectively, and flowed upward and exited at fractures from 303 to 319.5 ft; a very minor amount exited into fractures within coal beds at 240.4 and 252 ft bls. Transmissivity, estimated from analysis of the specific-capacity data and flowmeter logs, was about 18 ft2/d for the fracture zones from 567 to 580.5 ft and 6.7 ft2/d for fracture zones from 240.4 to 252 ft bls. The analysis estimated the hydraulic head of the lower zone and that of the upper flow zone was 8 ft higher and 37 ft lower than the composite water level in the test hole, respectively. Water samples of the freshwater inflow from zones at 567 to 580.5 ft bls had a total dissolved solids concentration of 577 mg/L indicating that these zone are in the lower part of the active groundwater flow system. Below the freshwater-bearing zone at 580.5 ft, the flowmeter did not detect any vertical flow in the test hole, and the gradient of the temperature log approached the geothermal gradient, indicating little ambient fluid flow and minimal fracture transmissivity below this depth. However, small seeps of saline water having total dissolved solids concentrations of greater than about 6,200 mg/L at 945 and 946 ft bls, from dark-greenish-gray to greenish-gray silty beds, were delineated by a time series of specific conductancelogs and observed on the video log. A wat

Pennsylvania↗
USGS2014

Observations from borehole dilution logging experiments in fractured crystalline rock under variable hydraulic conditions

Identifying hydraulically active fractures in low permeability, crystalline-bedrock aquifers requires a variety of geophysical and hydrogeophysical borehole tools and approaches. One such approach is Single Borehole Dilution Tests (SBDT), which in some low flow cases have been shown to provide greater resolution of borehole flow than other logging procedures, such as vertical differential Heat Pulse Flowmeter (HPFM) logging. Because the tools used in SBDT collect continuous profiles of water quality or dye changes, they can identify horizontal flow zones and vertical flow. We used SBDT with a food grade blue dye as a tracer and dual photometer-nephelometer measurements to identify low flow zones. SBDT were conducted at seven wells with open boreholes (exceeding 300 ft). At most of the wells HPFM logs were also collected. The seven wells are set in low-permeability, fractured granite and gneiss rocks underlying a former tetrachloroeythylene (PCE) source area at the Savage Municipal Well Superfund site in Milford, NH. Time series SBDT logs were collected at each of the seven wells under three distinct hydraulic conditions: (1) ambient conditions prior to a pump test at an adjacent well, (2) mid test, after 2-3 days of the start of the pump test, and (3) at the end of the test, after 8-9 days of the pump test. None of the SBDT were conducted under pumping conditions in the logged well. For each condition, wells were initially passively spiked with blue dye once and subsequent time series measurements were made. Measurement accuracy and precision of the photometer tool is important in SBDT when attempting to detect low rates of borehole flow. Tests indicate that under ambient conditions, none of the wells had detectable flow as measured with HPFM logging. With SBDT, 4 of the 7 showed the presence of some very low flow. None of 5 (2 of the 7 wells initially logged with HPFM under ambient conditions were not re-logged) wells logged with the HPFM during the pump test had detectable flow. However, 3 of the 5 wells showed the patterns of very low flow with SBDT during the pump test including pumping induced changes of inflow and outflow patterns at one well.

Conference Paper↗
USGS2014

Drilling and geophysical logs of the tophole at an oil-and-gas well site, Central Venango County, Pennsylvania

In a study conducted by the U.S. Geological Survey, in cooperation with the Pennsylvania Department of Conservation and Natural Resources, Bureau of Topographic and Geologic Survey, drilling and geophysical logs were used to characterize the geohydrologic framework and the freshwater and saline-water zones penetrated by the tophole at an oil-and-gas well site in central Venango County, Pennsylvania. The geohydrologic setting of the well site is typical of the dissected Appalachian Plateau underlain by Pennsylvanian and Mississippian sandstone and shale. The drilling, gamma, and acoustic-televiewer logs collected from the 575-foot deep tophole define the penetrated Pennsylvanian and Mississippian stratigraphic units and their lithology. The caliper, video, and acoustic-televiewer logs delineate multiple bedding-related and high-angle fractures in the lower Pottsville Group and Shenango Formation from 22 to 249 feet below land surface. The caliper and acoustic-televiewer logs indicate a sparsity of fractures below 249 feet below land surface in the lowermost Shenango Formation, Cuyahoga Group, Corry Sandstone, “Drake Well” formation, and upper Riceville Formation. About half of the blown yield during drilling of the tophole was from fractures in the upper Shenango Formation between 80 and 167 feet below land surface and the other half from fractures in the lower Shenango between 190 and 249 feet below land surface. Following drilling, fractures above the water level at about 145 feet below land surface produced freshwater with a specific conductance of less than 150 microsiemens per centimeter at 25 degrees Celsius that cascaded down the hole. As indicated by the fluid resistivity and temperature logs, most of the downflow exited the hole at the water-bearing fractures at 249 feet below land surface. The downward flow in the tophole reflects the downward hydraulic gradient between the water-bearing fractures above the water level and those at 249 feet below land surface. Low conductivity and high resistivity values on the dual induction logs indicate freshwater above 285 feet below land surface in the Shenango sandstones, which is consistent with a specific conductance of blown yield of 400 microsiemens per centimeter at 25 degrees Celsius at 200 feet below land surface. High conductivity and low resistivity values on the induction logs indicate the presence of saline water below 450 feet in the Corry Sandstone. The highest specific conductance of the blown yield, 1,200 microsiemens per centimeter at 25 degrees Celsius, was measured at 480 feet below land surface following penetration of the Corry Sandstone. Collection and integrated analysis of drilling and geophysical logs provided an efficient and effective means for characterizing the geohydrologic framework and conditions penetrated by the tophole at the selected oil-and-gas well site. The logging methods and lessons learned at this well site could be applied at other oil-and-gas drilling sites to better characterize the shallow subsurface with the overall goal of protecting freshwater aquifers during hydrocarbon development.

Pennsylvania↗
USGS2014

Geologic and hydrogeologic frameworks of the Biscayne aquifer in central Miami-Dade County, Florida

Evaluations of the lithostratigraphy, lithofacies, paleontology, ichnology, depositional environments, and cyclostratigraphy from 11 test coreholes were linked to geophysical interpretations, and to results of hydraulic slug tests of six test coreholes at the Snapper Creek Well Field (SCWF), to construct geologic and hydrogeologic frameworks for the study area in central Miami-Dade County, Florida. The resulting geologic and hydrogeologic frameworks are consistent with those recently described for the Biscayne aquifer in the nearby Lake Belt area in Miami-Dade County and link the Lake Belt area frameworks with those developed for the SCWF study area. The hydrogeologic framework is characterized by a triple-porosity pore system of (1) matrix porosity (mainly mesoporous interparticle porosity, moldic porosity, and mesoporous to megaporous separate vugs), which under dynamic conditions, produces limited flow; (2) megaporous, touching-vug porosity that commonly forms stratiform groundwater passageways; and (3) conduit porosity, including bedding-plane vugs, decimeter-scale diameter vertical solution pipes, and meter-scale cavernous vugs. The various pore types and associated permeabilities generally have a predictable vertical spatial distribution related to the cyclostratigraphy. The Biscayne aquifer within the study area can be described as two major flow units separated by a single middle semiconfining unit. The upper Biscayne aquifer flow unit is present mainly within the Miami Limestone at the top of the aquifer and has the greatest hydraulic conductivity values, with a mean of 8,200 feet per day. The middle semiconfining unit, mainly within the upper Fort Thompson Formation, comprises continuous to discontinuous zones with (1) matrix porosity; (2) leaky, low permeability layers that may have up to centimeter-scale vuggy porosity with higher vertical permeability than horizontal permeability; and (3) stratiform flow zones composed of fossil moldic porosity, burrow related vugs, or irregular vugs. Flow zones with a mean hydraulic conductivity of 2,600 feet per day are present within the middle semiconfining unit, but none of the flow zones are continuous across the study area. The lower Biscayne aquifer flow unit comprises a group of flow zones in the lower part of the aquifer. These flow zones are present in the lower part of the Fort Thompson Formation and in some cases within the limestone or sandstone or both in the uppermost part of the Pinecrest Sand Member of the Tamiami Formation. The mean hydraulic conductivity of major flow zones within the lower Biscayne aquifer flow unit is 5,900 feet per day, and the mean value for minor flow zones is 2,900 feet per day. A semiconfining unit is present beneath the Biscayne aquifer. The boundary between the two hydrologic units is at the top or near the top of the Pinecrest Sand Member of the Tamiami Formation. The lower semiconfining unit has a hydraulic conductivity of less than 350 feet per day. The most productive zones of groundwater flow within the two Biscayne aquifer flow units have a characteristic pore system dominated by stratiform megaporosity related to selective dissolution of an Ophiomorpha-dominated ichnofabric. In the upper flow unit, decimeter-scale vertical solution pipes that are common in some areas of the SCWF study area contribute to high vertical permeability compared to that in areas without the pipes. Cross-hole flowmeter data collected from the SCWF test coreholes show that the distribution of vuggy porosity, matrix porosity, and permeability within the Biscayne aquifer of the SCWF is highly heterogeneous and anisotropic. Groundwater withdrawals from production well fields in southeastern Florida may be inducing recharge of the Biscayne aquifer from canals near the well fields that are used for water-management functions, such as flood control and well-field pumping. The SCWF was chosen as a location within Miami-Dade County to study the potential for such recharge to the Biscayne aquifer from the C–2 (Snapper Creek) canal that roughly divides the well field in half. Geologic, hydrogeologic, and hydraulic information on the aquifer collected during construction of monitoring wells within the SCWF could be used to evaluate the groundwater flow budget at the well-field scale.

Florida↗
USGS2013

Geophysical logging and geologic mapping data in the vicinity of the GMH Electronics Superfund site near Roxboro, North Carolina

Geologic mapping, the collection of borehole geophysical logs and images, and passive diffusion bag sampling were conducted by the U.S. Geological Survey North Carolina Water Science Center in the vicinity of the GMH Electronics Superfund site near Roxboro, North Carolina, during March through October 2011. The study purpose was to assist the U.S. Environmental Protection Agency in the development of a conceptual groundwater model for the assessment of current contaminant distribution and future migration of contaminants. Data compilation efforts included geologic mapping of more than 250 features, including rock type and secondary joints, delineation of more than 1,300 subsurface features (primarily fracture orientations) in 15 open borehole wells, and the collection of passive diffusion-bag samples from 42 fracture zones at various depths in the 15 wells.

North Carolina↗
USGS2013

Water resources and shale gas/oil production in the Appalachian Basin: critical issues and evolving developments

Unconventional natural gas and oil resources in the United States are important components of a national energy program. While the Nation seeks greater energy independence and greener sources of energy, Federal agencies with environmental responsibilities, state and local regulators and water-resource agencies, and citizens throughout areas of unconventional shale gas development have concerns about the environmental effects of high volume hydraulic fracturing (HVHF), including those in the Appalachian Basin in the northeastern United States (fig. 1). Environmental concerns posing critical challenges include the availability and use of surface water and groundwater for hydraulic fracturing; the migration of stray gas and potential effects on overlying aquifers; the potential for flowback, formation fluids, and other wastes to contaminate surface water and groundwater; and the effects from drill pads, roads, and pipeline infrastructure on land disturbance in small watersheds and headwater streams (U.S. Government Printing Office, 2012). Federal, state, regional and local agencies, along with the gas industry, are striving to use the best science and technology to develop these unconventional resources in an environmentally safe manner. Some of these concerns were addressed in U.S. Geological Survey (USGS) Fact Sheet 2009–3032 (Soeder and Kappel, 2009) about potential critical effects on water resources associated with the development of gas extraction from the Marcellus Shale of the Hamilton Group (Ver Straeten and others, 1994). Since that time, (1) the extraction process has evolved, (2) environmental awareness related to high-volume hydraulic fracturing process has increased, (3) state regulations concerning gas well drilling have been modified, and (4) the practices used by industry to obtain, transport, recover, treat, recycle, and ultimately dispose of the spent fluids and solid waste materials have evolved. This report updates and expands on Fact Sheet 2009–3032 and presents new information regarding selected aspects of unconventional shale gas development in the Appalachian Basin (primarily Virginia, West Virginia, Maryland, Pennsylvania, Ohio, and New York). This document was prepared by the USGS, in cooperation with the U.S. Department of Energy, and reviews the evolving technical advances and scientific studies made in the Appalachian Basin between 2009 and the present (2013), addressing past and current issues for oil and gas development in the region.

Maryl;New York;Ohio;Pennsylvania;Virginia;West Vir↗
USGS2013

Geophysical-log and hydraulic-test analyses of groundwater-production wells at the Hannahville Indian Community, Menominee County, Michigan

The U.S. Geological Survey, in cooperation with the Hannahville Indian Community, evaluated the geohydrology of the bedrock formations and hydraulic properties of groundwater-production wells at the Hannahville Indian Community in Menominee County, Michigan. Geophysical logs were collected from five wells at two sites during September 2012. The logs were analyzed to characterize the lithostratigraphy, bedding and fractures, and hydraulic properties of the geologic formations and aquifers beneath the Hannahville Indian Community. The geophysical logs collected included natural gamma radiation, electromagnetic conductivity, wellbore image, caliper, ambient and stressed flowmeter, fluid resistivity, temperature, and wellbore deviation. The geophysical logs were analyzed with results from short-term hydraulic tests to estimate the transmissivity and water-level altitudes of flow zones penetrated by the wells. The geophysical log analysis indicated the wells penetrated four distinct lithostratigraphic units—shale and carbonate rock, upper carbonate rock, carbonate rock and glauconitic sandstone, and lower carbonate rock. Most of the fractures penetrated by the wellbores appeared to be related bedding partings. The lower carbonate rock unit contained solution features. Analysis of the geophysical logs and hydraulic tests indicated that each of the five wells penetrated from one to four flow zones. The Casino 5 well penetrated a flow zone that was associated with solution features and had an estimated total transmissivity of 4,280 feet squared per day (ft 2 /d), the highest estimate for all the wells. The Casino 3 well penetrated four flow zones and had an estimated total transmissivity of 3,570 ft 2 /d. The flow zones penetrated in the lower carbonate rock unit by the Casino 3 and 5 wells were hydraulically connected. The Golf Shack well penetrated two flow zones and had an estimated total transmissivity of 40 ft 2 /d, the lowest estimate for all the wells. The Community 1 and Community 2 wells penetrated three and four flow zones, respectively, and had estimated total transmissivity values of 185 and 280 ft 2 /d, respectively.

Michigan↗
USGS2013

Geohydrologic and water-quality characterization of a fractured-bedrock test hole in an area of Marcellus shale gas development, Bradford County, Pennsylvania

Open-File Miscellaneous Investigation 13–01.1 presents the results of geohydrologic investigations on a 1,664-foot-deep core hole drilled in the Bradford County part of the Gleason 7.5-minute quadrangle in north-central Pennsylvania. In the text, the authors discuss their methods of investigation, summarize physical and analytical results, and place those results in context. Four appendices include (1) a full description of the core in an Excel worksheet; (2) water-quality and core-isotope analytical results in Excel workbooks; (3) geophysical logs in LAS and PDF files, and an Excel workbook containing attitudes of bedding and fractures calculated from televiewer logs; and (4) MP4 clips from the downhole video at selected horizons.

Pennsylvania↗
USGS2012

Time series geophysical monitoring of permanganate injections and in situ chemical oxidation of PCE, OU1 area, Savage Superfund Site, Milford, NH, USA

In situ chemical oxidation (ISCO) treatment with sodium permanganate, an electrically conductive oxidant, provides a strong electrical signal for tracking of injectate transport using time series geophysical surveys including direct current (DC) resistivity and electromagnetic (EM) methods. Effective remediation is dependent upon placing the oxidant in close contact with the contaminated aquifer. Therefore, monitoring tools that provide enhanced tracking capability of the injectate offer considerable benefit to guide subsequent ISCO injections. Time-series geophysical surveys were performed at a superfund site in New Hampshire, USA over a one-year period to identify temporal changes in the bulk electrical conductivity of a tetrachloroethylene (PCE; also called tetrachloroethene) contaminated, glacially deposited aquifer due to the injection of sodium permanganate. The ISCO treatment involved a series of pulse injections of sodium permanganate from multiple injection wells within a contained area of the aquifer. After the initial injection, the permanganate was allowed to disperse under ambient groundwater velocities. Time series geophysical surveys identified the downward sinking and pooling of the sodium permanganate atop of the underlying till or bedrock surface caused by density-driven flow, and the limited horizontal spread of the sodium permanganate in the shallow parts of the aquifer during this injection period. When coupled with conventional monitoring, the surveys allowed for an assessment of ISCO treatment effectiveness in targeting the PCE plume and helped target areas for subsequent treatment.

New Hampshire↗
USGS2011

Cross-borehole flow analysis to characterize fracture connections in the Melechov Granite, Bohemian-Moravian Highland, Czech Republic

Application of the cross-borehole flow method, in which short pumping cycles in one borehole are used to induce time-transient flow in another borehole, demonstrated that a simple hydraulic model can characterize the fracture connections in the bedrock mass between the two boreholes. The analysis determines the properties of fracture connections rather than those of individual fractures intersecting a single borehole; the model contains a limited number of adjustable parameters so that any correlation between measured and simulated flow test data is significant. The test was conducted in two 200-m deep boreholes spaced 21 m apart in the Melechov Granite in the Bohemian-Moravian Highland, Czech Republic. Transient flow was measured at depth stations between the identified transmissive fractures in one of the boreholes during short-term pumping and recovery periods in the other borehole. Simulated flows, based on simple model geometries, closely matched the measured flows. The relative transmissivity and storage of the inferred fracture connections were corroborated by tracer testing. The results demonstrate that it is possible to assess the properties of a fracture flow network despite being restricted to making measurements in boreholes in which a local population of discrete fractures regulates the hydraulic communication with the larger-scale aquifer system.

Bohemian-moravian Highland↗
USGS2011

Geophysical, stratigraphic, and flow-zone logs of selected wells in Cayuga County, New York, 2001–2011

Geophysical logs were collected and analyzed along with bedrock core samples and bedrock outcrops to define the bedrock stratigraphy and flow zones penetrated by 93 monitor and water-supply wells in Cayuga County, New York. The work was completed from 2001 through 2011 as part of an investigation of volatile-organic compound contamination in the carbonate-bedrock aquifer system between Auburn and Union Springs. The borehole logs included gamma, caliper, wellbore image, fluid property, and flow logs. The log information was used with bedrock core samples to define the regional stratigraphy, evaluate flow zones within the bedrock aquifers, and develop and implement a multilevel monitoring design for groundwater levels and water quality within the study area.

New York↗
USGS2010

Hydrogeology of the potsdam sandstone in northern New York

The Potsdam Sandstone of Cambrian age forms a transboundary aquifer that extends across northern New York and into southern Quebec. The Potsdam Sandstone is a gently dipping sequence of arkose, subarkose, and orthoquartzite that unconformably overlies Precambrian metamorphic bedrock. The Potsdam irregularly grades upward over a thickness of 450 m from a heterogeneous feldspathic and argillaceous rock to a homogeneous, quartz-rich and matrix-poor rock. The hydrogeological framework of the Potsdam Sandstone was investigated through an analysis of records from 1,500 wells and geophysical logs from 40 wells, and through compilation of GIS coverages of bedrock and surficial geology, examination of bedrock cores, and construction of hydrogeological sections. The upper several metres of the sandstone typically is weathered and fractured and, where saturated, readily transmits groundwater. Bedding-related fractures in the sandstone commonly form sub-horizontal flow zones of relatively high transmissivity. The vertical distribution of sub-horizontal flow zones is variable; spacings of less than 10 m are common. Transmissivity of individual flow zones may be more than 100 m 2 /d but typically is less than 10 m 2 /d. High angle fractures, including joints and faults, locally provide vertical hydraulic connection between flow zones. Hydraulic head gradients in the aquifer commonly are downward; a laterally extensive series of sub-horizontal flow zones serve as drains for the groundwater flow system. Vertical hydraulic head differences between shallow and deep flow zones range from 1 m to more than 20 m. The maximum head differences are in recharge areas upgradient from the area where the Chateauguay and Chazy Rivers, and their tributaries, have cut into till and bedrock. Till overlies the sandstone in much of the study area; its thickness is generally greatest in the western part, where it may exceed 50 m. A discontinuous belt of bedrock pavements stripped of glacial drift extends across the eastern part of the study area; the largest of these is Altona Flat Rock. Most recharge to the sandstone aquifer occurs in areas of thin, discontinuous till and exposed bedrock; little recharge occurs in areas where this unit is overlain by thick till and clay. Discharge from the sandstone aquifer provides stream and river baseflow and is the source of many springs. A series of springs that are used for municipal bottled water and fish-hatchery supply discharge from 1,000 to 5,000 L/min adjacent to several tributaries east of the Chateauguay River. The major recharge areas for the Chateauguay springs are probably upgradient to the southeast, where the till cover is thin or absent.

New York↗