Search USGSSearch

SEARCH · Search USGS

Results for “Completion Report”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

749 recordsLinked to original sources

Completion summary for monitor wells NRF-17 and NRF-18 at the Naval Reactors Facility, Idaho National Laboratory, Idaho

The U.S. Geological Survey (USGS)—in cooperation with the U.S. Department of Energy (DOE) for the Naval Reactors Laboratory Field Office that supports operations for the Naval Reactors Facility (NRF) located at the Idaho National Laboratory (INL)—drilled and constructed well NRF-17 (formerly borehole USGS 151) and well NRF-18 (formerly borehole USGS 152) for stratigraphic framework analyses and water-quality monitoring at the Idaho National Laboratory (INL) near the NRF, in southeastern Idaho. Borehole USGS 151 was continuously cored from about 48 to 1,070 feet (ft) below land surface (BLS); rotary drilled from approximately 1,070 to 1,720 ft BLS; and re-drilled to complete construction as a monitor well NRF-17, completed to 461 ft BLS. Borehole USGS 152 was continuously cored from approximately 19 to 1,259 ft BLS; rotary drilled from approximately 1,259 to 1,630 ft BLS; and re-drilled to complete construction as a monitor well NRF-18, completed to 450 ft BLS. Geophysical data were examined with photographed core material to record lithologic descriptions and to suggest zones where groundwater flow was anticipated. Basalt flows varied from highly fractured to dense, with high-to-low vesiculation. Well NRF-17 generally was constructed in mostly dense basalt (greater than 75 percent), and well NRF-18 was constructed in primarily fractured and (or) vesicular basalt. In well NRF-17, the well capacity is directly affected by the limited amount of fractured basalt, which serves as the primary pathway for groundwater. This effect was observed during the pumping test conducted after the well's final construction. Single-well aquifer tests were done at wells NRF-17 and NRF-18 to provide estimates of transmissivity and hydraulic conductivity after final well construction and initial well development. Estimated values of transmissivity and hydraulic conductivity for well NRF-17 were 8.81 feet squared per day (ft 2 /d) and 1.04×10 -2 feet per day (ft/d), respectively. Estimated values of transmissivity and hydraulic conductivity for well NRF-18 were 4.77×10 3 ft 2 /d and 5.61 ft/d, respectively. The NRF-17 pump test resulted in 19.41 ft of measured drawdown at a sustained average pumping rate of 3.3 gallons per minute (gal/min). The NRF-18 pump test resulted in 0.55 ft of measured drawdown at a sustained average pumping rate of 31.0 gal/min. Water-quality samples collected from the two wells were analyzed for cations, anions, metals, nutrients, volatile organic compounds, stable isotopes, and radionuclides. Water samples for select inorganic constituents showed concentrations consistent with signatures from tributary valley groundwater with influences from ephemeral surface-water recharge from the Big Lost River. Water-quality samples analyzed for stable isotopes of oxygen and hydrogen are consistent with signatures from tributary valley groundwater and surface-water recharge inputs to the aquifer. No measured water-quality results were greater than their respective maximum contaminant levels for public drinking-water supplies. Inorganic and nutrient water-quality results for well NRF-17 and well NRF-18 suggest the groundwater in this area is potentially affected by industrial wastewater disposal.

Idaho

Mapping potential sensitivity to hydrogeomorphic change in the UMRS riverscape

In 2020 the U.S. Geological Survey (USGS), as part of the Upper Mississippi River Restoration (UMRR) Program, began a new project to characterize potential hydrogeomorphic change associated with hydrogeomorphic units (HGUs) and their catenae (units linked by their association with sediment sources and flow origins). The goal of the project was to develop a geographic information system (GIS) database of HGUs for the Upper Mississippi River System (UMRS) available to both scientists and river managers working on UMRR studies and HREP planning and design studies. The characterization was based on a hydrogeomorphic change hierarchical classification developed previously for the UMRS. The products were generated with automated techniques in a GIS using systemic datasets. Landforms were mapped from the 2015 UMRS topobathymetric dataset with geomorphon (shape-based) tools tailored for the large riverscape, valley bottom environments in the UMRS. A clustering analysis was applied to the resulting landforms to identify HGUs associated with zones of perennial low flows, bankfull flows, and overbank floodplains. Catenae were assembled based on the proximity of the units to the main channel, tributary mouths, and side channels from previously published aquatic areas (USACE, 2018) coupled with least-cost flowpath linkages between potential sediment origins and planform change units developed by Rogala, Fitzpatrick, and Henderson (2020). These GIS-based analyses were successful at identifying a range of HGUs using an automated technique with available data across the entire riverscape, with emphasis on those that have the potential for hydrogeomorphic change. Most of the resulting features are depositional, as expected in a large river system. However, this is the first attempt of linking tributary inputs, side channel erosion and levee breaches with their depositional counterparts. The approach was successfully piloted in Pools 8 and 10 in the Upper Impounded Reach and Pool 14 in the Lower Impounded Reach, with next steps for application in reaches of the unimpounded section and Illinois River. This report emphasizes results from Pool 10, which was the focus of most of our attention during the pilot phase.

Illinois, Indiana, Iowa, Minnesota, Missouri, Sout

2024 Crustal Deformation Modeling Workshop report

The 2024 Crustal Deformation Modeling Workshop was held June 10–14 at the Colorado School of Mines. The workshop included two days of tutorials on using PyLith for crustal deformation modeling, followed by three days of science talks and discussions. The workshop focused on four primary themes: ● Constraining long-term fault slip rates and their uncertainties using geodetic and geologic data; ● Earthquake cycle modeling with a focus on constraining models using seismic and geodetic data; ● Interaction of fluids and faulting; and ● Separating contributions of surface loading and tectonic loading in crustal deformation. The complete agenda is available on the CIG website.

Conference Paper

The National Map Corps—Federal Emergency Management Agency and Oak Ridge National Laboratory pilot project report

This report provides an overview of the U.S. Geological Survey National Map Corps —Federal Emergency Management Agency and Oak Ridge National Laboratory pilot project in St. James Parish, Louisiana, that began in February 2024 and ended at the end of March 2024. The project used the power of The National Map Corps’ volunteer community to improve building classifications in the original Federal Emergency Management Agency’s U.S.A. Structures dataset. The report highlights the project’s completion and details the work and results achieved through a collaborative effort to enhance geospatial data quality and utility.

Open-File Report

Satellite tracking of Galapagos Petrel Pterodroma phaeopygia reveals distribution and movements during chick rearing

We tracked 19 adult Galapagos Petrels Pterodroma phaeopygia during the chick-rearing seasons in 2009 and 2010 (Santa Cruz Island [ n = 16] and Floreana Island [ n = 3]) in the Galápagos Islands, Ecuador. Eight petrels performed 27 complete foraging trips lasting 0.6 to 18.8 days. Short trips (3.2 ± 2.1 days; 785 km; max displacement 671 km) and long trips (10.8 ± 3.9 days; 2,856 km; max displacement 1,034 km) resulted in concentrated use of waters off southern and western Isabela Island and within the Galápagos Marine Reserve (GMR). Less concentrated time extended farther southwest and eastward, in that case toward mainland Ecuador. Total distance covered among all completed trips, independent of duration, was strongly correlated with trip duration ( R ² = 0.92), indicating a strategy favoring active searching and foraging over commuting. Petrels ranged across Ecuador's exclusive economic zone (EEZ), as well as other countries' (Colombia, Costa Rica, Perú), and waters beyond; they spent 46%, 27%, and 34% of their time in the GMR during short, long, and apparent (incomplete) trips, respectively. However, overlap with EEZs or marine protected areas (MPAs) does not necessarily confer protection, because commercial tuna fishing, including legal fishing historically permitted inside the GMR, occurs within these waters. Including all complete and incomplete trips, petrels spent 37% of their time in high-seas waters without formal protection, outside both MPAs and EEZs. While some hot spots overlapped Galápagos MPAs, the far-ranging nature of chick-provisioning petrels underscores the importance for this species of also having coordinated, multinational protection of the high seas.

Floreana Island, Galápagos Islands, Santa Cruz Isl

Enhanced geothermal systems electric-resource assessment for the Great Basin, southwestern United States

The U.S. Geological Survey recently (2025) completed a provisional assessment of the geothermal-electric resources associated with high-temperature, low-permeability rock formations of the Great Basin, Southwestern United States. If sufficient technological advances to commercialize enhanced geothermal systems occur, then a current best provisional estimate for electric-power generation capacity of 135 gigawatts electric are available from the upper 6 kilometers of the Earth’s crust. This estimate is a potential substantial increase of the installed geothermal electricity-generating capacity from <1 to 10 percent of current total U.S. power production capacity.

California, Idaho, Nevada, Oregon, Utah

Bathymetric and acoustic-backscatter mapping of Lake Sammamish, Washington, during USGS field activity 2021-656-FA

In 2021, scientists from the U.S. Geological Survey (USGS) acquired bathymetric and acoustic-backscatter data within Lake Sammamish, Washington. Mapping was completed to find evidence of past earthquakes such as underwater landslides and is part of a larger USGS project to understand the overall geologic hazards history of the Cascadia Margin region. The survey was conducted using the USGS research vessel Parke Snavely outfitted with an interferometric sidescan-sonar system for swath mapping. Three estimates of bathymetric uncertainty were calculated from the post-processed bathymetric data. This report provides a summary of the mapping mission.

Washington

Characterization of change in tree cover state and condition over the conterminous United States

Variability in the effects of disturbances and extreme climate events can lead to changes in tree cover over time, including partial or complete loss, with diverse ecological consequences. It is therefore critical to identify in space and time the change processes that lead to tree cover change. Studies of change are often hampered by the lack of data capable of consistently detecting different types of change. Using the Landsat satellite record to create a long time-series of land cover and land cover change, the U.S. Geological Survey Land Change Monitoring Assessment and Projection (LCMAP) project has made an annual time series of land cover across the conterminous United States for the period 1985 to 2018. Multiple LCMAP products analyzed together with map validation reference plots provide a robust basis for understanding tree cover change. In LCMAP (Collection 1.2), annual change detection is based on harmonic model breaks calculated at each Landsat pixel from the Continuous Change Detection and Classification (CCDC) algorithm. The results showed that the majority of CCDC harmonic model breaks (signifying change) indicated partial tree cover loss (associated with management practices such as tree cover thinning) as compared to complete tree cover loss (associated with practices like clearcut harvest or fire disturbance). Substantially fewer occurrences of complete tree cover loss were associated with change in land cover state. The area of annual tree cover change increased after the late 1990s and stayed high for the rest of the study period. The reference data showed that tree harvest dominated across the conterminous United States. The majority of tree cover change occurred in evergreen forests. Large estimates of disturbance-related tree cover change indicated that tree cover loss may have previously been underreported due to omission of partial tree cover loss in prior studies. This has considerable implications for forest carbon accounting along with tracking ecosystem goods and services.

Forests

The 3D National Topography Model Call for Action—Part 1. The 3D Hydrography Program

The U.S. Geological Survey is initiating the 3D Hydrography Program (3DHP), the first systematic remapping of the Nation’s surface waters since the original 1:24,000-scale topographic mapping program was active from 1947 to 1992. Building on decades of experience maintaining the National Hydrography Dataset (NHD), the Watershed Boundary Dataset (WBD), and the NHDPlus High Resolution (NHDPlus HR), the 3DHP will completely refresh the Nation’s hydrography data and improve discovery and sharing of water-related data. The design of the 3DHP is based on the results of a study that estimated that the fully implemented program would have the potential to provide more than $1 billion in benefits to Federal, State, Tribal, Territorial, and local governments and to private and nonprofit organizations every year, in addition to myriad societal benefits. The 3DHP would directly support better decision making regarding water resources by providing more accurate, complete, and integrated information than is currently available. The 3DHP datasets will include a three-dimensional (3D) hydrography network generated from and integrated with elevation data from the 3D Elevation Program (3DEP) to better represent stream gradients and channel conditions, along with waterbodies, hydrologic units, hydrologically enhanced elevation and other surfaces, and more consistent and accurate attributes. The 3DHP datasets will inherit key attributes of the NHD, WBD, and NHDPlus HR, and they also will include new attributes and links to other data such as the U.S. Fish and Wildlife Service National Wetlands Inventory, groundwater data, and engineered hydrologic systems such as stormwater networks. The 3DHP will be designed to provide a set of open and interoperable web-based tools, maps, and data catalogs, creating a robust system for users to reference their information about water; the system elements are collectively referred to as the “infostructure.” The 3DHP and the infostructure can provide a foundational geospatial underpinning for the Internet of Water, a community-based effort to modernize tools and technologies to share water data. As proposed, the 3DHP would begin providing products and services to the public in 2024.

Circular

Bathymetric maps, surface areas, and storage capacities of Council Grove Lake and Marion Reservoir, Kansas, and Pine Creek Lake, Oklahoma, 2024

The U.S. Geological Survey, in cooperation with the U.S. Army Corps of Engineers, completed high-resolution multibeam bathymetric surveys to compute new elevation-area-capacity tables for Council Grove Lake and Marion Reservoir, Kansas, and Pine Creek Lake, Oklahoma. Elevation-area-capacity tables identify the relation between the water-surface elevation, surface area, and storage capacity of the lake. The surface areas and storage capacities of each lake were computed from bathymetric surfaces combining multibeam echo sounder data collected in 2024 and light detection and ranging point-cloud data collected in 2016 and 2018.

Kansas, Oklahoma

Uppermost Oligocene and Miocene diatom biostratigraphy of Ocean Drilling Program Sites 682 and 688 from the Peru Margin

The diatom biochronology of ODP (Ocean Drilling Program) Holes 682A and 688E provides a detailed framework for refiningMiocene diatom zonation in the East Pisco Basin of southern Peru, establishing both a nearly complete offshore reference section and a correlation tool for the fragmentary onshore vertebrate-bearing deposits. This new biostratigraphic record documents a complete succession of low latitude and/or northeastern Pacific Miocene diatom zones, with two notable exceptions: a dissolution and/or hiatus interval (*16.5–14 Ma) during the Middle Miocene Climatic Optimum and a likely earliest Miocene hiatus (*23.4–21.8 Ma). Although eastern equatorial Pacific diatom zones characterize the Upper Oligocene and Lower Miocene strata, an increased abundance of cool-water diatoms that lived during the Middle and Late Miocene allows better application of northeast Pacific diatom zones, except during the Messinian (7–6 Ma) when warm-water diatoms predominate. The effects of eustatic sea level and tectonics on depositional sequences in the EPB and in offshore cores off central Peru are discussed.

Stratigraphy

The abandoned mine inventory of the United States—A brief summary

The Infrastructure Investment and Jobs Act of 2021 required the Secretary of the Interior to establish a program to inventory abandoned hard-rock mines in the United States. The Department of the Interior’s Office of Environmental Policy and Compliance asked the U.S. Geological Survey’s Mineral Deposit Database project (USMIN) to use existing data sources to build an inventory of all individual abandoned mine features in the United States. In addition to feature locations, this new database documents the surface land management agency, associated physical and environmental hazards, and any completed mitigation efforts. This information will improve risk assessment and support land management efforts, including hazard mitigation, ecosystem restoration planning, and reclamation. This fact sheet provides a brief overview of USMIN’s collaborative efforts with Federal, State, and Tribal agencies to build a comprehensive and authoritative national inventory of abandoned mine features.

Fact Sheet

Treatability study to evaluate bioremediation of trichloroethene at Site K, former Twin Cities Army Ammunition Plant, Arden Hills, Minnesota, 2020–22

Executive Summary Chlorinated solvents, including trichloroethene (TCE) and other chlorinated volatile organic compounds (cVOCs), are widespread contaminants that can be treated by bioremediation approaches that enhance anaerobic reductive dechlorination. Reductive dechlorination can be enhanced either through the addition of an electron donor (biostimulation) or the addition of a known dechlorinating culture (bioaugmentation) along with an electron donor. Although bioremediation has been applied at many TCE-contaminated groundwater sites, application in source zones at sites where residual dense nonaqueous phase liquid (DNAPL) is present is more limited. In this study, laboratory and field treatability tests were completed to evaluate the potential application of anaerobic bioremediation for a shallow groundwater plume containing TCE in a perched alluvial aquifer at Site K, former Twin Cities Army Ammunition Plant, Arden Hills, Minnesota, which was on the National Priorities List as the New Brighton/Arden Hills Superfund site until 2019. In addition to the presence of residual DNAPL at the site, temporal variability in groundwater flow directions and input of oxygenated recharge were possible complicating factors for the application of enhanced anaerobic biodegradation in the shallow plume. The Site K plume extends beneath the footprint of Building 103, which was demolished in 2006, and soil excavations to a maximum depth of 6 feet (ft) below ground surface in 2014 were known to leave some deeper contaminated soil in place in the TCE source area. Groundwater treatment at the site, formalized as part of the 1997 Record of Decision, has been in operation since 1986 and consists of an extraction trench at the downgradient edge of the plume to collect groundwater, which is then pumped to an on-site air stripper. Groundwater concentrations in the plume have been relatively stable since treatment began, indicating a continued source of TCE in the aquifer. The desire for a destructive remedy that would enhance the removal of cVOCs in the aquifer at Site K and shorten the remediation timeframe led the U.S. Army to request that the U.S. Geological Survey conduct a groundwater treatability study to assess bioremediation. This report describes the U.S. Geological Survey bioremediation treatability study conducted during 2020–22, including pre-design site characterization to assist in formulating the bioremediation approach, laboratory experiments to support the design of the field pilot test, and implementation and 1-year performance monitoring results for the pilot test. Pre-design site characterization included the collection of soil cores for cVOC analysis and lithologic descriptions and the re-installment of three wells to obtain hydrologic measurements and initial groundwater chemistry. Relatively flat head gradients were measured at the site, and substantial decreases in water-level elevations occurred from spring to summer (May–July 2021). Continuous water-level monitoring indicated a rapid response to precipitation. Groundwater flow velocities were consistently less than 0.5 foot per day, and the pilot bioremediation test was therefore designed with short lateral distances (about 5 ft) between injection and individual monitoring points. Soil analyses confirmed that high volatile organic compound contamination was left in place in the source area. The highest concentrations were near or in clay at the base of the perched aquifer. Concentrations of cVOCs measured in the replaced wells were consistent with historical data and had a maximum TCE concentration of 57,700 micrograms per liter (μg/L), indicative of nearby residual DNAPL based on the general rule of observed concentrations exceeding 1 percent of solubility. The primary TCE daughter product detected was 1,2-cis-dichloroethene (cisDCE), which indicated limited reductive dechlorination in the plume. Groundwater in both the source and downgradient areas was relatively reducing during the pre-design characterization, particularly in the source area where methane concentrations greater than 400 μg/L were measured. Initial laboratory tests conducted using native aquifer microorganisms from the three replacement wells showed that anaerobic TCE biodegradation rates were low when biostimulated with the addition of sodium lactate as an electron donor, also known as a carbon donor, and resulted in the production of only cisDCE. Addition of a known dechlorinating culture, WBC-2, however, resulted in rapid biodegradation and production of ethene, verifying complete reductive dechlorination of TCE. Microcosms constructed with aquifer soil collected from the site were used to evaluate other electron donors besides lactate to support reductive dechlorination by WBC-2, including corn syrup as an alternative fast-release compound and whey, soy-based vegetable oil, and 3-D Microemulsion (Regenesis, San Clemente, California) as slow-release compounds. First-order rate constants for total organic chlorine removal in these WBC-2 amended microcosms were greatest with either lactate or vegetable oil as the donor, ranging between 0.061 and 0.047 per day or corresponding half-lives of 11–15 days. Testing of commercial products in other WBC-2-bioaugmented microcosms led to selection for the field pilot test of an emulsified vegetable oil product that also contained some sodium lactate as a fast-release donor. Delaying the addition of WBC-2 relative to the donor in the microcosms resulted in the most rapid overall biodegradation rates. The selected design for the pilot test utilized three separate test plots, each about 30-ft wide and 60-ft long: plots GS1 and GS2 in the source area of the plume and plot GS3 in the downgradient area of the plume near the excavation trench. Each test plot had one injection well, one monitoring well upgradient from the injection point, and 12 surrounding monitoring wells in a grid to capture variable groundwater flow directions. Donor injections, which included a bromide tracer, were completed in October 2021, immediately following baseline sampling, and the WBC-2 culture was injected about 40 days later, between November 30 and December 2, 2021. Performance monitoring conducted until December 2022 included hydrologic measurements and analyses of cVOCs, redox-sensitive constituents, dissolved organic carbon, bromide, volatile fatty acids, compound-specific carbon isotopes, and microbial communities. The biogeochemical data collected during the pilot tests in the three treatment plots showed that enhanced, complete reductive dechlorination of cVOCs in the groundwater was achieved in the GS1 and GS3 plots. In contrast, evidence of distribution of the injected amendments and subsequent biodegradation was limited in GS2, which was in an area of more heterogeneous soil lithology and low water table elevations. The molar composition of volatile organic compounds in the GS1 and GS3 plots was dominated by ethene in wells that were reached by the injected amendments by the end of the monitoring period. In the GS1 and GS3 plots, similar patterns were observed of cVOC concentrations decreasing to near detection levels, or below, at some wells sampled in July and October 2022, whereas ethene became dominant and indicated sustained complete reductive dechlorination. Baseline cVOC concentrations were more than a factor of 10 higher in the groundwater in the GS1 plot than in GS3, but no apparent inhibition of complete dechlorination occurred. As expected from the initial pre-design site data and the laboratory experiments, enhanced dissolution of residual DNAPL coupled to biodegradation was evident in the GS1 plot, where a marked increase in dichloroethene (DCE) above the initial baseline and upgradient TCE and DCE concentrations occurred. DCE concentrations subsequently declined where DNAPL dissolution was evident, concurrent with production of vinyl chloride and then predominantly ethene. Thus, overall biodegradation rates outpaced the DNAPL dissolution and desorption and DCE production in the source area. This success in complete degradation to predominantly ethene was achieved even in areas where the DCE concentrations reached a maximum of about 30,000 μg/L. Compound specific isotope analysis of carbon in TCE, cisDCE, trans-1,2-dichloroethene, and vinyl chloride was conducted to provide another line of evidence of the occurrence and extent of anaerobic biodegradation. Along a flow path in each plot that was affected by the injected amendments, carbon isotopes in the TCE and daughter cVOCs in the groundwater became isotopically heavier, indicating biodegradation. Enhanced biodegradation rates calculated from the field tests in GS1 and GS3 showed half-lives of 36.9–75.3 days for DCE degradation and 9.48–38.5 days for ethene production. Notably, these ethene production rates calculated from the field tests are consistent with the results of WBC-2-bioaugmented microcosms amended with either lactate or vegetable oil, which had half-lives for total organic chlorine removal that ranged from 11 to 15 days. These rates indicated rapid enhanced biodegradation, which is promising for application of a full-scale bioremediation remedy. Ultimately, however, the mass of residual or sorbed TCE in the aquifer that remains accessible for dissolution and biodegradation would likely control the time required for a full-scale bioremediation effort to achieve performance goals for TCE and cisDCE specified in the Record of Decision for Site K. The field pilot tests showed that the relatively low hydraulic head gradients and temporal changes in groundwater flow directions in the shallow aquifer would add complexity to a full-scale bioremediation effort. The radius of influence (ROI) at GS1 and GS3 (16.3 ft and 12.7 ft, respectively) were close to the design ROI of 15 ft. The estimated ROI at GS2 was about four times the design ROI, but may be less reliable at this location owing to groundwater flow direction. In addition, the low temperatures following WBC-2 injection in late November to early December 2021, in combination with the low hydraulic head gradients, were probably major factors in the delay observed before the onset of enhanced biodegradation following injection of the culture. Additional test injections could be beneficial to optimize the timing of donor and culture injections with the variable temperatures and hydraulic head in the shallow aquifer.

Minnesota

ARCHI: A new R package for automated imputation of regionally correlated hydrologic records

Missing data in hydrological records can limit resource assessment, process understanding, and predictive modeling. Here, we present ARCHI (Automated Regional Correlation Analysis for Hydrologic Record Imputation), a new, open-source software package in R designed to aggregate, impute, cluster, and visualize regionally correlated hydrologic records. ARCHI imputes missing data in “target” records by linear regression using more complete “reference” records as predictors. Automated imputation is implemented using a novel, iterative algorithm that allows each site to be considered a target or reference for regression, growing the pool of complete references with each imputed record until viable gap-filling ceases. Users can limit artifacts from spurious correlations by specifying model-acceptance criteria and applying geospatial, correlation, and group-based filters to control reference selection. ARCHI provides additional functions for visualizing results, clustering records with similar correlation structures, evaluating holdout data, and interactive parameterization with an accessible and intuitive graphical user interface (GUI). This methods brief provides an overview of the ARCHI package, modeling guidelines, and benchmarking on two regional groundwater-level datasets from the Central Valley, CA and Long Island, NY. We evaluate ARCHI alongside widely used multivariate imputation software to highlight and contextualize its computational efficiency, imputation accuracy, and model transparency when applied to large, groundwater-level datasets.

California, New York

Summary of results from electromagnetic and galvanic soundings on Kilauea Iki lava lake, Hawaii

The purpose of this report is to summarize various electrical sounding studies made on the Kilauea Iki lava lake and to present some of the preliminary interpretations that resulted from the measurements. The following discussion is not intended as a complete interpretation, but is intended to summarize the major points made in an invited oral presentation at the American Geophysical Union fall meeting held in San Francisco, Calif. on December 6, 1976. This paper was part of a group of papers dealing with various geophysical studies recently made on the Kilauea Iki lava lake. A general plan map of Kilauea Iki lava lake is shown in figure 1. Electromagnetic (EM) loop-loop soundings, D.C. resistivity soundings, and VLF apparent resistivity measurements were made on the lave lake surface. All of these surveys were made to determine the geoelectric structure of the lava lake and to determine parameters of the molten basaltic lens that exist in the partially solidified lava lake.

Hawaii

Water quality of selected springs and public-supply wells, Pine Ridge Indian Reservation, South Dakota, 1992-97

This report presents results of a water-quality study for the Pine Ridge Indian Reservation, South Dakota. The study was a cooperative effort between the U.S. Geological Survey and the Water Resources Department of the Oglala Sioux Tribe. Discharge and water-quality data were collected during 1992-97 for 14 contact springs located in the northwestern part of the Reservation. Data were collected to evaluate potential alternative sources of water supply for the village of Red Shirt, which currently obtains water of marginal quality from a well completed in the Inyan Kara aquifer. During 1995-97, water-quality data also were collected for 44 public-supply wells that serve about one-half of the Reservation's population. Quality-assurance sampling was used to evaluate the precision and accuracy of environmental samples. Ten of the springs sampled contact the White River Group, and four contact the Pierre Shale. Springs contacting the White River Group range from calcium bicarbonate to sodium bicarbonate water types. Two springs contacting the Pierre Shale have water types similar to this; however, sulfate is the dominant anion for the other two springs. In general, springs contacting the White River Group are shown to have better potential as alternative sources of water supply for the village of Red Shirt than springs contacting the Pierre Shale. Nine of the springs with better water quality were sampled repeatedly; however, only minor variability in water quality was identified. Six of these nine springs, of which five contact the White River Group, probably have the best potential for use as water supplies. Discharge from any of these six springs probably would provide adequate water supply for Red Shirt during most periods, based on a limited number of discharge measurements collected. Concentrations of lead exceeded the U.S. Environmental Protection Agency (USEPA) action level of 15 µg/L for three of these six springs. Five of these six springs also had arsenic concentrations that exceeded 10 µg/L, which could be problematic if the current maximum contaminant level (MCL) is lowered. Blending of water from one or more springs with water from the existing Inyan Kara well may be an option to address concerns regarding both quantity and quality of existing and potential sources. All nine springs that were sampled for indicator bacteria had positive detections on one or more occasions during presumptive tests. Although USEPA standards for bacteria apply only to public-water supplies, local residents using spring water for domestic purposes need to be aware of the potential health risks associated with consuming untreated water. One spring contacting the White River Group and two springs contacting the Pierre Shale exceeded 15 pCi/L for gross alpha; these values do not necessarily constitute exceedances of the MCL, which excludes radioactivity contributed by uranium and radon. Additional sampling using different analysis techniques would be needed to conclusively determine if any samples exceeded this MCL. Nine springs were sampled for selected pesticides and tritium. The pesticides atrazine, carbaryl, and 2,4-D were not detected in any of the samples. The nine springs were analyzed for tritium in order to generally assess the age of the water and to determine if concentrations exceeded the MCL established for gross beta-particle activity. Tritium results indicated two springs are composed primarily of water recharged prior to atmospheric testing of nuclear bombs and two other springs have a relatively large percentage of test-era water. The remaining five springs had tritium values that indicated some percentage of test-era water; however, additional sampling would be needed to determine whether water is predominantly pre- or post-bomb age. Of the 44 public-supply wells sampled, 42 are completed in the Arikaree aquifer, one is completed in an alluvial aquifer, and one is completed in the Inyan Kara aquifer. Water from the alluvial well is a sodium bicarbonate water type, water from Arikaree aquifer ranges from calcium bicarbonate to sodium bicarbonate types, and water from the Inyan Kara well is a calcium sulfate bicarbonate type. Of the 44 wells sampled, 28 (64 percent) tested positive for indicator bacteria in presumptive tests. Because these were single samples that generally were collected upstream from chemical treatment feeders, positive detections do not necessarily constitute exceedances of drinking-water standards. A single sample from an Arikaree well exceeded the MCL for arsenic of 50 µg/L. Arsenic exceeded 10 µg/L for six additional Arikaree wells and for the alluvial well and the Inyan Kara well, which could be problematic if the current MCL is lowered. The alluvial well also exceeded the secondary maximum contaminant level (SMCL) for dissolved solids, which is non-enforceable, and the action level for lead. The Inyan Kara well exceeded the SMCL's for iron and for manganese and the MCL of 5 pCi/L for radium-226 and 228 combined. Several Arikaree wells exceeded SMCL's for either pH, sulfate, dissolved solids, iron, or manganese. One Arikaree well exceeded the MCL of 4.0 mg/L for fluoride and another exceeded the MCL of 10 mg/L for nitrite plus nitrate. Ten Arikaree wells equalled or exceeded 15 pCi/L for gross alpha; however, these values do not necessarily constitute exceedances of the MCL, which excludes radioactivity contributed by uranium and radon. Additional sampling using different analysis techniques would be needed to conclusively determine if any samples exceeded this MCL. Eight wells, all from the Arikaree aquifer, equalled or exceeded the proposed MCL of 20 µg/L for uranium and 33 wells (75 percent) equalled or exceeded one-half of the proposed MCL. Although this standard has only been proposed, additional information regarding the extent of elevated uranium concentrations in the Arikaree aquifer, and the geochemical processes involved, may be beneficial. It was determined from analyses of uranium isotope data for five wells that the source of elevated uranium concentrations is naturally occurring, rather than anthropogenic.

South Dakota

Generalized potentiometric maps of the Fort Union, Hell Creek, and Fox Hills aquifers within the Standing Rock Reservation

Generalized potentiometric surfaces of the Fort Union, Hell Creek, and Fox Hills aquifers were constructed to assess the groundwater resources of the Standing Rock Reservation. Additionally, this information can provide water managers with tools and data to effectively manage water resources in the future. Previous studies that mapped the geology and hydrogeology of the area at differing scales were used to confirm in which aquifer the study wells were completed. Water-level data from wells are provided by the U.S. Geological Survey Groundwater System Inventory database, the South Dakota Department of Agriculture and Natural Resources, and the North Dakota Department of Water Resources. Hydrographs were constructed for five selected observation wells to evaluate historical water-level fluctuations and trends. Hydrographs for the Hell Creek aquifer showed a flat trend with a rise in 2020. Hydrographs for the deeper Fox Hills aquifer showed that water levels fluctuated in response to climatic conditions and demonstrated an increasing trend in water-level elevations starting in 2010. Hydrographs were not constructed for any wells completed in the Fort Union Formation because none of the wells had continuous long-term measurements. Generalized potentiometric surfaces, constructed from interpolating water-level elevations, gave insight into groundwater flow directions. Groundwater in the Fort Union aquifer likely flows radially outward from the northwest part of the study area to the northeast and south-southeast parts. Groundwater in the Hell Creek aquifer generally flows from higher elevations in the northwest towards lower areas, where surface-water tributaries have incised into the aquifer. Groundwater in the Fox Hills aquifer likely flows from higher elevations in the west, southwest, and central parts of the study area towards the valleys of the Grand River and Missouri River. Most wells used for constructing potentiometric maps had only one recorded water-level measurement from drillers at the time of well construction. These measurements are often subject to error because the well is still recovering and because of spatial limitations of data availability. Also, because single water-level measurements were recorded at different points in time, additional uncertainty is introduced by fluctuating climatic conditions effect on water levels. Potentiometric map interpretation limitations are a result of areas with sparse data. Limitations also arise from potentiometric surfaces generalizing a complex and dynamic hydrogeologic system; however, the generalized potentiometric surface maps can be used to assist water managers and can help prioritize locations for future monitoring in areas with high uncertainty from sparse existing data.

North Dakota, South Dakota

Geophysical identification of potential groundwater – surface water interactions in the Bonita Peak Mining District, San Juan County, Colorado

This report includes the results and interpretation of geophysical investigations to aid in the location, identification, and conceptual site model (CSM) development of the near surface groundwater and surface water hydrology of the Upper Cement Creek and California Gulch of the Animas Rivers within the Bonita Peak Mining Districts (BPMD). Mine influenced water (MIW) from numerous mine adits within the BPMD has altered the geochemistry and ecology of these ground and surface waters. Many studies of varying scales have investigated the geology, hydrogeology, geochemistry, and aqueous chemistry of these adits and impacted areas. Field investigations using non-invasive geophysical methods were conducted in the summer of 2019 to aid in identifying potential groundwater inputs to these streams and further the CSM of the near surface within and along these streams. Two field deployments were completed in August and September of 2019. In August 2019, Phase 1 was completed using multifrequency electromagnetic induction (EMI) and thermal infrared imaging (TIR) to measure the bulk electrical conductivity, magnetic susceptibility, and the temperature response at known and suspected groundwater seeps into the Upper Cement Creek and California Gulch stretches of these alpine streams. Results and interpretation from Phase 1 were used to co-locate stretches of these streams for further detailed fiber optic distributed temperature system (FODTS) monitoring of the temperature dynamics for submeter identification of potential groundwater seeps during Phase 2. Phase 2 included additional EMI measurements, FODTS measurements, and repeated some Phase 1 measurements for improved data quality. All these data were used for the combined qualitative interpretation identifying seep locations. The data from both Phase 1 and Phase 2 are available in the USGS data release at: https://www.sciencebase.gov/catalog/item/5f18a30082cef313ed84879b. These data include detailed near-surface electrical conductivity and magnetic susceptibility mapping, discrete TIR imaging, and several kilometers of FODTS data. These data were georeferenced and used to identify potential groundwater seeps into these streams. The results indicate a complex near surface geophysical and hydrogeologic regime. Seeps are classified and spatially correlated to the EMI, TIR, and geochemical sampling results. This report is a thorough compilation of the geophysical field efforts in the summer of 2019, the data processing, and interpretations of these data. These data alone should not be used for final interpretations of the complex hydrogeology within these alpine systems. Rather, these data should be combined with other known data from various investigations to further refine the CSM and guide decisions for future investigations, watershed protective measures, and other site decisions. Geographical information system (GIS) layers of these results are available to project managers for such integration and combined interpretations.

Colorado