Search USGS⌕ Search

SEARCH · Search USGS

Results for “ACS Division of Environmental Chemistry, Preprints”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

18 recordsLinked to original sources
USGS1997

Occurrence of the gasoline oxygenate MTBE and BTEX compounds in municipal stormwater in the United States, 1991-95

The U.S. Geological Survey (USGS) sampled stormwater in 16 cities and metropolitan areas that are required to obtain permits to discharge stormwater from their municipal storm-sewer system into surface water. Concentrations of 62 volatile organic compounds (VOCs), including methyl tert-butyl ether (MTBE) and BTEX (benzene, toluene, ethylbenzene, and total xylene) compounds, were measured in 592 stormwater samples collected in these cities and metropolitan areas from 1991 through 1995. MTBE was the seventh most frequently detected VOC in municipal stormwater. In decreasing order, the most frequently detected VOCs were toluene, total xylene, chloroform, total trimethylbenzene, tetrachloroethene, and naphthalene. MTBE was detected in 6.9 percent (41 of 592) of stormwater samples collected. When detected, concentrations of MTBE ranged from 0.2 to 8.7 micrograms per liter (??g/L), with a median of 1.5 ??g/L. All detections of MTBE were less than the lower limit of the U.S. Environmental Protection Agency's (USEPA) draft drinking water lifetime health advisory (20 ??g/L). Eighty-three percent of all detections of MTBE in stonnwater were in samples collected during October through March of each year (1991-95), which corresponds with the expected seasonal use of oxygenated gasoline in areas where carbon monoxide exceeds established air-quality standards. The median concentration of MTBE and benzene for all samples was statistically different and higher in samples collected during October through March than samples collected during April through September. Sixty-six percent of all MTBE: detections occurred with BTEX compounds, and a proportionate increase in concentrations was found when these compounds occurred together. Detected concentrations of toluene and total xylene ranged from 0.2 to 6.6 ??g/L and 0.2 to 15 ??g/L with median concentrations of 0.3 and 0.4 ??g/L, respectively.

ACS Division of Environmental Chemistry, Preprints↗
USGS2001

Biodegradation of MTBE by indigenous aquifer microorganisms under artificial oxic conditions

The hypothesis that artificial oxic conditions will lead to MTBE biodegradation by indigenous microorganisms in anoxic, gasoline-contaminated aquifers was examined by adding oxygen in the form of a metal peroxide slurry to an anoxic part of gasoline-contaminated aquifer in South Carolina. Field observations of relatively rapid aerobic MTBE biodegradation following oxygen addition suggest that the indigenous bacteria have become acclimated not only to mg/L concentrations of MTBE in the gasoline plume, but also to periodic delivery of oxygen by recharge events. Significant natural attenuation of MTBE could occur if the oxygen limitations naturally associated with gasoline releases can be removed, either under natural conditions where discharging anoxic groundwater comes into contact with oxygen, or artificial conditions where oxygen can be added to aquifers containing mg/L concentrations of MTBE. This final solution might be an effective strategy for intercepting characteristically long MTBE plumes, particularly at sites not characterized by groundwater discharge to land surface. This is an abstract of a paper presented at the 222nd ACS National Meting (Chicago, IL 8/26-30/2001).

ACS Division of Environmental Chemistry, Preprints↗
USGS2001

Potential contribution of microbial degradation to natural attenuation of MTBE in surface water systems

The potential contribution of in situ biodegradation as a mechanism for natural attenuation of MTBE in surface water was studied. Surface water sediments from streams and lakes at 11 sites throughout the US. Microbial degradation of [U-14C] MTBE was observed in surface-water-sediment microcosms under anaerobic conditions, but the efficiency and products of anaerobic MTBE biodegradation were strongly dependent on the predominant terminal electron accepting conditions. In the presence of substantial methanogenic activity, MTBE biodegradation was nominal and involved reduction of MTBE to t-butanol (TBA). Under more oxidizing conditions, minimal accumulation of 14C-TBA and significant mineralization of [U-14C] MTBE to 14CO2 were observed. Microorganisms inhabiting the bed sediments of streams and lakes could degrade MTBE effectively under a range of anaerobic terminal electron accepting conditions. Thus, anaerobic bed sediment microbial processes also might contribute to natural attenuation of MTBE in surface water systems throughout the US. This is an abstract of a paper presented at the 222nd ACS National Meting (Chicago, IL 8/26-30/2001).

ACS Division of Environmental Chemistry, Preprints↗
USGS1996

The potential for increasing the use of catalytic carbons in commercial applications

A carbon catalyst, prepared either by oxidizing activated carbon with air at 500-700??C or by oxidizing activated carbon with boiling nitric acid followed by heating it to 500-700??C, is the subject of this paper. This catalyst, designated OAC500-700, catalyzes the removal of hydrogen chloride from alkyl halides. Because OAC500-700 retains adsorptive properties of an activated carbon it can be used both to adsorb pollutants from liquid or gaseous streams and to convert them to recyclable products. A highly-developed micropore structure is not required for all uses of activated carbon or a catalyst produced from it. A comparatively inexpensive ($325/ton projected) low surface area (<300 m2/g) carbon has been developed at the Illinois State Geological Survey (ISGS) for cleaning incinerator flue gas. This grade of activated carbon is widely used in Europe for flue gas cleaning and for other applications. Activated carbon adsorbers of some type are required by recently passed U.S. Environmental Protection Agency (EPA) regulations for municipal waste combustors to control emission of cadmium, mercury, lead, dioxins, furans and acid gases (U.S. EPA, 1995). Similar regulations are expected for hospital and hazardous waste incinerators. The marketing of less costly activated carbons of the type used widely in Europe is expected in the United States. Low cost OAC500-700 made from less expensive grades of activated carbon may become available for large scale adsorbent/catalyst systems designed to both remove and decompose toxic pollutants found in liquid and gaseous streams, chlorinated organic compounds in particular.

ACS Division of Fuel Chemistry, Preprints↗
USGS2000

Properties and potential environmental applications of carbon adsorbents from waste tire rubber

The properties of tire-derived carbon adsorbents (TDCA) produced from select tire chars were compared with those derived from an Illinois coal and pistachio nut shells. Chemical analyses of the TDCA indicated that these materials contain metallic elements not present in coal-and nut shell-derived carbons. These metals, introduced during the production of tire rubber, potentially catalyze steam gasification reactions of tire char. TDCA carbons contained larger meso-and macopore volumes than their counterparts derived from coal and nut shell (on the moisture-and ash-free-basis). Adsorptive properties of the tire-derived adsorbent carbons for air separation, gas storage, and gas clean up were also evaluated and compared with those of the coal-and nut shell derived carbons as well as a commercial activated carbon. The results revealed that TDCA carbons are suitable adsorbents for removing vapor-phase mercury from combustion flue gases and hazardous organic compounds from industrial gas streams.

ACS Division of Fuel Chemistry, Preprints↗
USGS2000

Stanford-USGS shrimp-RG ion microprobe: A new approach to determining the distribution of trace elements in coal

The distribution of Cr and other trace metals of environmental interest in a range of widely used U.S. coals was investigated using the Stanford-USGS SHRIMP-RG ion microprobe . Using the oxygen ion source, concentrations of Cr (11 to 176 ppm), V (23 to 248 ppm), Mn (2 to 149 ppm), Ni (2 to 30 ppm), and 13 other elements were determined in illite/smectite, a group of clay minerals commonly present in coal. The results confirm previous indirect or semi-quantitative determinations indicating illite/smectite to be an important host of these metals. Calibration was achieved using doped aluminosilicate-glass synthetic standards and glasses prepared from USGS rock standards. Grains for analysis were identified optically, and confirmed by 1) precursory electron microprobe analysis and wavelength-dispersive compositional mapping, and 2) SHRIMP-RG major element data obtained concurrently with trace element results. Follow-up investigations will focus on the distribution of As and other elements that are more effectively ionized with the cesium primary beam currently being tested.

ACS Division of Fuel Chemistry, Preprints↗