SEARCH · Search USGS

Results for “Acoustics”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,495 records · Page 83Linked to original sources

USGS2024

Monitoring marine eruptions

Introduction Submarine volcanoes produce much of the same seismicity and eruptive activity as subaerial volcanoes and can pose hazards to society. Although they can be monitored with similar techniques and methods as described in other chapters of this volume, their submerged location brings unique challenges. This chapter addresses these challenges and provides recommendations for monitoring volcanoes fully or partly in marine environments to meet the capabilities described in other chapters of this volume. The United States and its territories host dozens of submarine volcanoes with most (around 60) in the Commonwealth of the Northern Mariana Islands. Approximately 20 of the Northern Mariana Islands submarine volcanoes are known to be hydrothermally active, and 10 have confirmed eruptions since the 1950s (for example, Baker and others, 2008; Tepp and others, 2019a). Nine of those volcanoes were considered by the National Volcanic Threat Assessment (Ewert and others, 2018) to have a combination of eruptive type and summit depth that poses a higher risk of hazardous eruptions, although only one was listed as a moderate (level 3) threat. Other notable submarine volcanoes of interest to the United States that have historically erupted are Axial Seamount off the Washington State coast, Kamaʻehuakanaloa in Hawaiʻi, and Vailuluʻu seamount in American Samoa. All of these, however, have a low risk of hazards because of their depth (greater than 600 meters below sea level) and eruptive type and so are not included in the National Volcanic Threat Assessment. In addition to submarine volcanoes, the submerged flanks of island volcanoes can also be a source of hazardous submarine eruptions—for example, the 1877 eruption of Mauna Loa, Hawai‘i, in Kealakekua Bay (Wanless and others, 2006). The most notable submarine eruption in recent times was the 2022 eruption of Hunga Tonga–Hunga Haʻapai in Tonga, which was one of the largest eruptions on Earth in the past 100 years. It created a massive volcanic plume, unprecedented shock waves, and far-reaching tsunami (Lynett and others, 2022). Other recent submarine eruptions in the Pacific Ocean Basin have produced subaerial plumes that reached aircraft heights (Carey and others, 2014) and large pumice rafts that can affect marine traffic and harbors (for example, Jutzeler and others, 2014; Kornei, 2019). These examples illustrate the potential hazards of major submarine eruptions. Yet, submarine volcanoes are largely unmonitored, and many eruptions occur that are unnoticed or only identified hours or days afterward. Within U.S. territory, submarine volcanoes in the Northern Mariana Islands have been known to produce eruptive activity that can affect society. Reports from fishermen and other marine vessels in the Northern Mariana Islands have noted underwater explosions, sea-surface discoloration, and bubbling water, all of which are known to be signs of submarine volcanic activity. South Sarigan seamount, located about 160 kilometers (km) north of Saipan, erupted in 2010 from greater than 150 meters below the sea surface, resulting in a gas and ash plume that reached more than 11.9 km into the atmosphere (for example, Searcy, 2013; Embley and others, 2014), high enough to affect international air traffic. Precursory and co-eruptive seismicity was detected on the regional Northern Mariana Islands seismic network (Searcy, 2013) and on global monitoring instruments (Green and others, 2013). Monitoring of submarine volcanoes is best accomplished with marine-based instrumentation, which is also useful for monitoring small island volcanoes that may not have the land area necessary for comprehensive subaerial monitoring. The primary marine-based instrumentation used for submarine volcanoes includes ocean-bottom pressure sensors to assess sea-floor deformation, ocean-bottom seismometers (OBSs) to detect seismicity, and both moored and ocean-bottom hydrophones to detect submarine explosions. Other sensors offer important monitoring data, such as turbidity, temperature, and chemistry of hydrothermal emissions. Marine-based instruments are typically deployed in campaign-style networks with no real-time telemetry owing to cost considerations and technical limitations. However, when necessary, marine instruments can be operated in real time using cables to transmit data to land-based facilities; other technologies for this purpose are in use or in development, such as acoustic transmission from the instrument to a moored buoy (Matsumoto and others, 2016) and a winch-based system with a satellite antenna that is part of the instrument mooring (Matsumoto and others, 2019). Emerging technologies for marine-based monitoring may be considered as part of a future monitoring plan. These technologies include ocean gliders and floats with on-board hydrophones that have been used to record earthquakes and submarine eruptions (for example, Matsumoto and others, 2013; Sukhovich and others, 2015) and fiber-optic cables that have been used as strainmeters to detect earthquakes (for example, Marra and others, 2018; Lindsey and others, 2019). Land-based instruments and satellites can also provide some capability for monitoring submarine volcanoes, but they provide more limited observations than marine-based instrumentation.

Scientific Investigations Report↗

USGS2025

Bathymetric contour maps, surface area and capacity tables, and bathymetric change maps for selected water-supply lakes in Missouri, 2022–23

Bathymetric data were collected at 13 water-supply lakes around the periphery of Missouri by the U.S. Geological Survey in cooperation with the Missouri Department of Natural Resources and various local agencies, as part of a multiyear effort to establish or update the surface area and capacity tables for the surveyed lakes. Surveys were carried out during the months of April and May in 2022 and 2023. All but two of the lakes had been surveyed previously by the U.S. Geological Survey, and the recent surveys were compared to the earlier surveys to document the changes in the bathymetric surface and capacity of the lake. Bathymetric data were collected using a high-resolution multibeam mapping system mounted on a boat. Supplemental depth data at three of the lakes were collected in shallow areas with an acoustic Doppler current profiler on a remote-controlled boat. Data points from the various sources were exported at a gridded data resolution appropriate to each lake, either 0.82 foot, 1.64 feet, or 3.28 feet. Data outside the multibeam survey extent and greater than the surveyed water-surface elevation were obtained from data collected using aerial light detection and ranging (lidar) point cloud data. A linear enforcement technique was used to add points to the dataset in areas of sparse data (the upper ends of coves where the water was shallow or aquatic vegetation precluded data acquisition) based on surrounding multibeam and upland data values. The various point datasets were used to produce a three-dimensional triangulated irregular network surface of the lake-bottom elevations for each lake. A surface area and capacity table was produced from the three-dimensional surface for each lake showing surface area and capacity at specified lake water-surface elevations. Various quality-assurance tests were conducted to ensure quality data were collected with the multibeam, including beam angle checks and patch tests. Additional quality-assurance tests were conducted on the gridded bathymetric data from the survey, the bathymetric surface created from the gridded data, and the contours created from the bathymetric survey.

Missouri↗

USGS2012

Computing discharge using the index velocity method

Application of the index velocity method for computing continuous records of discharge has become increasingly common, especially since the introduction of low-cost acoustic Doppler velocity meters (ADVMs) in 1997. Presently (2011), the index velocity method is being used to compute discharge records for approximately 470 gaging stations operated and maintained by the U.S. Geological Survey. The purpose of this report is to document and describe techniques for computing discharge records using the index velocity method. Computing discharge using the index velocity method differs from the traditional stage-discharge method by separating velocity and area into two ratings—the index velocity rating and the stage-area rating. The outputs from each of these ratings, mean channel velocity (V) and cross-sectional area (A), are then multiplied together to compute a discharge. For the index velocity method, V is a function of such parameters as streamwise velocity, stage, cross-stream velocity, and velocity head, and A is a function of stage and cross-section shape. The index velocity method can be used at locations where stage-discharge methods are used, but it is especially appropriate when more than one specific discharge can be measured for a specific stage. After the ADVM is selected, installed, and configured, the stage-area rating and the index velocity rating must be developed. A standard cross section is identified and surveyed in order to develop the stage-area rating. The standard cross section should be surveyed every year for the first 3 years of operation and thereafter at a lesser frequency, depending on the susceptibility of the cross section to change. Periodic measurements of discharge are used to calibrate and validate the index rating for the range of conditions experienced at the gaging station. Data from discharge measurements, ADVMs, and stage sensors are compiled for index-rating analysis. Index ratings are developed by means of regression techniques in which the mean cross-sectional velocity for the standard section is related to the measured index velocity. Most ratings are simple-linear regressions, but more complex ratings may be necessary in some cases. Once the rating is established, validation measurements should be made periodically. Over time, validation measurements may provide additional definition to the rating or result in the creation of a new rating. The computation of discharge is the last step in the index velocity method, and in some ways it is the most straight-forward step. This step differs little from the steps used to compute discharge records for stage-discharge gaging stations. The ratings are entered into database software used for records computation, and continuous records of discharge are computed.

Techniques and Methods↗

USGS2010

Stage measurement at gaging stations

Stream and reservoir stage are critical parameters in the computation of stream discharge and reservoir volume, respectively. In addition, a record of stream stage is useful in the design of structures that may be affected by stream elevation, as well as for the planning for various uses of flood plains. This report describes equipment and methodology for the observation, sensing, and recording of stage in streams and reservoirs. Although the U.S. Geological Survey (USGS) still uses the traditional, basic stilling-well float system as a predominant gaging station, modern electronic stage sensors and water-level recorders are now commonly used. Bubble gages coupled with nonsubmersible pressure transducers eliminate the need for stilling wells. Submersible pressure transducers have become common in use for the measurement of stage in both rivers and lakes. Furthermore, noncontact methods, such as radar, acoustic, and laser methods of sensing water levels, are being developed and tested, and in the case of radar, are commonly used for the measurement of stage. This report describes commonly used gaging-station structures, as well as the design and operation of gaging stations. Almost all of the equipment and instruments described in this report will meet the accuracy standard set by the USGS Office of Surface Water (OSW) for the measurement of stage for most applications, which is ±0.01 foot (ft) or 0.2 percent of the effective stage. Several telemetry systems are used to transmit stage data from the gaging station to the office, although satellite telemetry has become the standard. These telemetry systems provide near real-time stage data, as well as other information that alerts the hydrographer to extreme or abnormal events, and instrument malfunctions.

Techniques and Methods↗

USGS2001

Delineation of tidal scour through marine geophysical techniques at Sloop Channel and Goose Creek bridges, Jones Beach State Park, Long Island, New York

Inspection of the Goose Creek Bridge in southeastern Nassau County in April 1998 by the New York State Department of Transportation (NYSDOT) indicated a separation of bridge piers from the road bed as a result of pier instability due to apparent seabed scouring by tidal currents. This prompted a cooperative study by the U.S. Geological Survey with the NYSDOT to delineate the extent of tidal scour at this bridge and at the Sloop Channel Bridge, about 0.5 mile to the south, through several marine- geophysical techniques. These techniques included use of a narrow-beam, 200-kilohertz, research-grade fathometer, a global positioning system accurate to within 3 feet, a 3.5 to 7-kilohertz seismic-reflection profiler, and an acoustic Doppler current profiler (ADCP). The ADCP was used only at the Sloop Channel Bridge; the other techniques were used at both bridges. Results indicate extensive tidal scour at both bridges. The fathometer data indicate two major scour holes nearly parallel to the Sloop Channel Bridge—one along the east side, and one along the west side (bridge is oriented north-south). The scour-hole depths are as much as 47 feet below sea level and average more than 40 feet below sea level; these scour holes also appear to have begun to connect beneath the bridge. The deepest scour is at the north end of the bridge beneath the westernmost piers. The east-west symmetry of scour at Sloop Channel Bridge suggests that flood and ebb tides produce extensive scour. The thickness of sediment that has settled within scour holes could not be interpreted from fathometer data alone because fathometer frequencies cannot penetrate beneath the sea-floor surface. The lower frequencies used in seismic-reflection profiling can penetrate the sea floor and underlying sediments, and indicate the amount of infilling of scour holes, the extent of riprap under the bridge, and the assemblages of clay, sand, and silt beneath the sea floor. The seismic- reflection surveys detected 2 to 5 feet of sediment filling the scour holes at both bridges; this indicates that the fathometer surveys were undermeasuring the effective depth of bridge scour by 2 to 5 feet through their inability to penetrate the infilled sediment. Several clay layers with thicknesses of 3 to 5 feet were detected beneath the sea floor at both bridges. Most of the piers beneath Sloop Channel Bridge appear to be surrounded by riprap, but, in several areas the riprap appears to be slumping or sliding into adjacent scour holes. Similar slumping was indicated at the Goose Creek Bridge. Most of the sediment underlying the sea floor at both bridges is interpreted as a fine-grained, cross-bedded sand. ADCP data from Sloop Channel indicate that the constricted flow beneath the bridge increases the horizontal current velocities from 2 to 6 feet per second. Total measured discharge beneath Sloop Channel Bridge was 41,800 cubic feet per second at flood tide and 27,600 cubic feet per second at ebb tide.

Water-Resources Investigations Report↗

USGS2002

Application of advanced geophysical logging methods in the characterization of a fractured-sedimentary bedrock aquifer, Ventura County, California

An integrated suite of advanced geophysical logging methods was used to characterize the geology and hydrology of three boreholes completed in fractured-sedimentary bedrock in Ventura County, California. The geophysical methods included caliper, gamma, electromagnetic induction, borehole deviation, optical and acoustic televiewer, borehole radar, fluid resistivity, temperature, and electromagnetic flowmeter. The geophysical logging 1) provided insights useful for the overall geohydrologic characterization of the bedrock and 2) enhanced the value of information collected by other methods from the boreholes including core-sample analysis, multiple-level monitoring, and packer testing. The logged boreholes, which have open intervals of 100 to 200 feet, penetrate a sequence of interbedded sandstone and mudstone with bedding striking 220 to 250 degrees and dipping 15 to 40 degrees to the northwest. Fractures intersected by the boreholes include fractures parallel to bedding and fractures with variable strike that dip moderately to steeply. Two to three flow zones were detected in each borehole. The flow zones consist of bedding-parallel or steeply dipping fractures or a combination of bedding-parallel fractures and moderately to steeply dipping fractures. About 75 to more than 90 percent of the measured flow under pumped conditions was produced by only one of the flow zones in each borehole.

California↗

USGS2001

Evaluation of borehole geophysical logs and hydraulic tests, phase III, at AIW Frank/Mid-County Mustang Superfund Site, Chester County, Pennsylvania

Borehole geophysical logs, heatpulse-flowmeter measurements, and aquifer-isolation tests were used to characterize the ground-water-flow system at the AIW Frank/Mid-County Mustang Superfund Site. The site is underlain by fractured carbonate rocks. Caliper, natural-gamma, single-point-resistance, fluid-resistivity, and fluid-temperature logs were run in six wells, and an acoustic borehole televiewer and borehole deviation log was run in one well. The direction and rate of borehole-fluid movement was measured with a high-resolution heatpulse flowmeter for both nonpumping and pumping conditions in four wells. The heatpulse-flowmeter measurements showed flow within the borehole during nonpumping conditions in three of the four wells tested. Flow rates up to 1.4 gallons per minute were measured. Flow was upward in one well and both upward and downward in two wells. Aquifer-isolation (packer) tests were conducted in four wells to determine depth-discrete specific capacity values, to obtain depth-discrete water samples, and to determine the effect of pumping an individual fracture or fracture zone in one well on water levels in nearby wells. Water-level data collected during aquifer-isolation tests were consistent with and confirmed interpretations of borehole geophysical logs and heatpulse-flowmeter measurements. Seven of the 13 fractures identified as water-producing or water-receiving zones by borehole geophysical methods produced water at a rate equal to or greater than 7.5 gallons per minute when isolated and pumped. The specific capacities of isolated fractures range over three orders of magnitude, from 0.005 to 7.1 gallons per minute per foot. Vertical distribution of specific capacity between land surface and 298 feet below land surface is not related to depth. The four highest specific capacities, in descending order, are at depths of 174-198, 90-92, 118-119, and 34-37 feet below land surface.

Pennsylvania↗

USGS2000

Simulations of flooding on Tchoutacabouffa River at State Highways 15 and 67 at D'Iberville, Mississippi

A two-dimensional finite-element surface-water model was used to simulate the effects of the proposed State Highways 15 and 67 relocation on water-surface elevations and flow distributions for the 100-year flood on the Tchoutacabouffa River at D'Iberville, Mississippi. The Mississippi Department of Transportation plans to relocate State Highways 15 and 67 by removing a portion of the existing four-lane highway and constructing a four-lane facility upstream of the existing alignment. The proposed alignment is located on the northern floodplain and will tie into the existing highway about 1,000 feet north of the dual State Highways 15 and 67 bridges. The proposed alignment will intercept flows that cross the existing highway during large floods. Seven scenarios were simulated for the 100-year flood, including four proposed alternative configurations for drainage structures. The model grid was developed by using surveyed floodplain cross sections and channel bathymetry data obtained by using an Acoustic Doppler Current Profiler, in combination with a global positioning system. The model was calibrated and verified by using surveyed flood profiles through the study reach and flood discharge measurements obtained at the State Highways 15 and 67 crossing. Model parameters were adjusted so that the computed water-surface profiles agreed closely with the surveyed flood profiles. Computed water-surface differentials across the proposed alignment near the northern edge of the floodplain for the four alternatives proposed by the Mississippi Department of Transportation ranged from 1.4 to 2.6 feet. Much lower differentials were computed in the vicinity of the main-channel bridge. The computed water-surface elevation at McCully Drive, upstream of the proposed alignment, was 17.3 feet for existing conditions. Computed water-surface elevations at McCully Drive for the proposed alternatives ranged from 17.3 to 17.8 feet.

Mississippi↗

USGS2002

Three-dimensional measurements of flow in uncased wells completed in basalt, Mountain Home Air Force Base, Idaho, March 2000

Several ground-water monitoring wells on the Mountain Home Air Force Base in southwestern Idaho were constructed in February 2000 to replace existing monitoring wells that became ineffective as a result of declining water levels. Upon completion of the replacement wells, borehole geophysical logs were collected, including natural gamma radiation, electromagnetic induction, caliper, fluid temperature, and resistivity. A prototype borehole acoustic doppler velocimeter (B-ADV) was used to make experimental three-dimensional measurements of lateral and vertical flow in two of the replacement wells, MW11–2 and MW3–2, each 450 feet deep, to better understand ground-water flow in the basalt underlying this area. Measurements indicated two independent flow zones in each well: unit B, from about 380 to about 415 feet below land surface, and unit C, from about 415 to about 430 feet below land surface. In each well, direction of flow in unit B was north-northwest toward Canyon Creek and, in unit C, south-southwest toward the Snake River. Measurements also indicated downward intraborehole flow in both wells. Unit B appeared to represent a local-scale flow regime; unit C appeared to represent a regional flow regime. This information suggests the existence of a complex three-dimensional hydrogeologic setting that cannot be discriminated easily on conventional waterlevel maps. Although data from only two wells are insufficient to construct a conceptual model of the ground-water flow regime, these experimental results demonstrate the capability of the B-ADV to obtain detailed flow measurements that, combined with data from other types of geophysical logs, discrete measurements of hydraulic head, and water chemistry, would aid in future studies and management of the ground-water resources, including contaminant transport and remediation.

Idaho↗

USGS2002

Streamflow and nutrient data for the Yazoo River below Steele Bayou near Long Lake, Mississippi, 1996-2000

Increased nutrient loading to the Gulf of Mexico from off-continent flux has been identified as contributing to the increase in the areal extent of the low dissolved-oxygen zone that develops annually off the Louisiana and Texas coast. The proximity of the Yazoo River Basin in northwestern Mississippi to the Gulf of Mexico, and the intensive agricultural activities in the basin have led to speculation that the Yazoo River Basin contributes a disproportionate amount of nitrogen and phosphorus to the Mississippi River and ultimately to the Gulf of Mexico. An empirical measurement of the flux of nitrogen and phosphorus from the Yazoo Basin has not been possible due to the hydrology of the lower Yazoo River Basin. Streamflow for the Yazoo River below Steele Bayou is affected by backwater from the Mississippi River. Flow at the gage is non-uniform and varying, with bi-directional and reverse flows possible. Streamflow was computed by using remote sensing and acoustic and conventional discharge and velocity measurement techniques. Streamflow from the Yazoo River for the 1996-2000 period accounted for 2.8 percent of the flow of the Mississippi River for the same period. Water samples from the Yazoo River were collected from February 1996 through December 2000 and were analyzed for total nitrogen, nitrate, total phosphorus, and orthophosphorus as part of the U.S. Geological Survey National Water-Quality Assessment Program. These data were used to compute annual loads of nitrogen and phosphorus discharged from the Yazoo River for the period 1996-2000. Annual loads of nitrogen and phosphorus were calculated by two methods. The first method used multivariate regression and the second method multiplied the mean annual concentration by the total annual flow. Load estimates based on the product of the mean annual concentration and the total annual flow were within the 95 percent confidence interval for the load calculated by multivariate regression in 10 of 20 cases. The Yazoo River loads, compared to average annual loads in the Mississippi River, indicated that the Yazoo River was contributing 1.4 percent of the total nitrogen load, 0.7 percent of the nitrate load, 3.4 percent of the total phosphorus load, and 1.6 percent of the orthophosphorus load during 1996 - 2000. The total nitrogen, nitrate, and orthophosphorus loads in the Yazoo River Basin were less than expected, whereas the total phosphorus load was slightly higher than expected based on discharge.

Water-Resources Investigations Report↗

USGS2003

The effect of chamber mixing velocity on bias in measurement of sediment oxygen demand rates in the Tualatin River basin, Oregon

Three sediment oxygen demand (SOD) measurement chambers were deployed in the Tualatin River near Tigard, Oregon, at river mile 10 in August 2000. SOD rates were calculated for three different circulation velocities during each chamber deployment. The SOD rate at each velocity was calculated from a graph of dissolved oxygen concentration versus elapsed time. An acoustic doppler current profiler (ADCP) was used to measure stream discharge and near-bottom water velocities in the Tualatin at river mile 10 and at two upstream locations. Measured river and chamber velocities were similar, indicating that results from the chambers were representative of instream effects. At low to moderate chamber circulation velocities (less than about 7.5 centimeters per second), the measured SOD rate appeared to be only slightly affected by the circulation velocity, indicating that the measured rates reflect the rate of oxygen utilization by chemical and biological reactions in the sediment rather than the rate of physical transport of oxygen to the sediment-water interface. Above about 7.5 centimeters per second, however, the measured oxygen depletion rate was affected by the circulation velocity, as sufficient energy was generated within the chamber to resuspend bottom sediment, as evidenced by increased turbidity. The resuspended sediment particles contributed to the measured oxygen loss rate by increasing the surface area of decomposing material in contact with the water column, resulting in a measured SOD rate that was anomalously high. Two different alignments of the chamber circulation diffusers were tested. With both diffuser alignments, SOD rates were similar at circulation velocities low enough to avoid sediment resuspension. The same resuspension effect probably exists in the Tualatin River during storm-runoff events following prolonged periods of low flow, when increased stream velocity may result in the resuspension of bottom sediments. The resuspension causes increased turbidity and increased oxygen demand, resulting in lower instream dissolved oxygen concentrations.

Water-Resources Investigations Report↗

USGS2005

Borehole-geophysical and hydraulic investigation of the fractured-rock aquifer near the University of Connecticut Landfill, Storrs, Connecticut, 2000 to 2001

An integrated borehole-geophysical and hydraulic investigation was conducted at the former landfill area near the University of Connecticut in Storrs, Connecticut, where solvents and landfill leachate have contaminated a fractured-bedrock aquifer. Borehole-geophysical techniques and hydraulic methods were used to characterize the site bedrock lithology and structure, fractures, and hydraulic properties. The geophysical and hydraulic methods included conventional logs, borehole imaging, borehole radar, flowmeter under ambient- and stressed hydraulic conditions, and discrete-zone hydraulic testing, sampling, and monitoring. The conventional geophysical-logging methods included caliper, deviation, electromagnetic induction, gamma, specific conductance, and fluid temperature. The advanced methods included optical and acoustic imaging of the borehole wall, heat-pulse flowmeter, and directional radar reflection. Borehole-geophysical methods were used to further define conductive features identified with surface-geophysical methods in the first phase of the investigation. The results of the surface- and borehole-geophysical logging were evaluated in an iterative and integrated manner to develop a conceptual model of ground-water flow at the site. The rock type, foliation, and fractures at the site were characterized from high-resolution optical televiewer (OTV) images of rocks penetrated by the boreholes and were compared to drilling logs and conventional geophysical logs. The rocks are interpreted as fine- to mediumgrained quartz-feldspar-biotite-garnet gneiss and schist with local intrusions of quartz diorite and pegmatite and minor concentrations of sulfide mineralization similar to rocks described as the Bigelow Brook Formation on regional geologic maps. Layers containing high concentrations of sulfide minerals appear as high electrical conductivity zones on electromagnetic-induction and borehole-radar logs. Foliation in the rocks generally strikes to the southwest and northeast, and dips to the northwest and southeast consistent with previous investigations in this area. The orientation of foliation, however, varies locally and with depth in some of the boreholes. These results are consistent with geologic mapping that has identified small-scale folding. The orientations of the transmissive fractures identified in the six boreholes logged for this investigation are similar to the fracture orientations mapped in a previous investigation. Many of these fractures are oriented with a north-northwest strike and have a shallow dip to the west. Other transmissive fractures have a southwest strike and dip at shallow angles to the northwest, and some strike roughly east-west and dip to the north and south. Flowmeter logging was used to identify transmissive fractures and to estimate the hydraulic properties in the boreholes. Ambient down flow was measured in one borehole, and ambient up flow and down flow were measured in another borehole. The other four bedrock boreholes did not have measurable vertical flow. Under low-rate pumping conditions (0.25 to 0.5 gallons per minute), one to three inflow zones were identified in each well. Commonly, fractures that are active under ambient conditions contribute to the well under pumping conditions. The ambient conditions were incorporated into the determination of the relative proportions of transmissivity. Specific capacity and transmissivity were determined for these open-hole low-rate pumping tests. Quasi-steady-state water levels were reached in four of the boreholes, including MW201R, MW204R, MW302R, and W202-NE. When pumped at low-rate conditions for 0.5 to 4 hours, the specific capacity ranged from 0.03 to 0.18 gallons per minute per foot. The open-hole transmissivity estimates ranged from 4.9 to 30 feet squared per day (ft2/d). Open-hole transmissivity was determined for boreholes that did not reach quasi-steady-state conditions under low-rate pumping conditions. Transmissivity was estimated for MW201R, MW202R, and MW203R using non-equilibrium methods, pumping rate, and the transient drawdown data to estimate the open-hole transmissivity. Transmissivity in these boreholes ranged from 0.98 to 3.2 ft 2 /d. The transmissivity and head of individual fractures or zones of fractures were estimated from heat-pulse flowmeter data acquired under ambient and stressed conditions. In the absence of ambient flow, data from two profiles of heat-pulse flowmeter data under two different stressed conditions were used to estimate the transmissivity and head of individual fracture zones. Only two boreholes, MW302R and W202-NE, had sufficient data for these analyses. The estimated transmissivity of individual transmissive zones ranged from 1.2 to 9.2 ft 2 /d. The transmissivity values determined by this numerical simulation method were less than the open-hole estimations, which were 15 and 30 ft 2 /d. Transmissivity also was measured directly over discrete intervals of the borehole using a straddle-packer apparatus and constant-rate pumping tests. Pumping rates were less than or equal to 0.25 gallons per minute. These discretezone single-hole pumping tests were conducted over a short period of time, usually about 30 minutes to 1 hour in duration. Pumping continued until the test zone reached a steady-state water level or until it was determined that the zone could not yield water at the pumped rate. The estimated transmissivity of individual transmissive zones ranged from about 0.21 to 11 ft 2 /d. The zone at a depth of 197 feet in W202-NE was the only zone that had discrete-interval testing with a straddle packer and sufficient heat-pulse flowmeter data for modeling the flow and estimating transmissivity and head. The two methods produced similar results. The straddle-packer method estimated a transmissivity of 4.7 ft 2 /d, and the heat-pulse flowmeter modeling results estimated a transmissivity of 6.9 ft 2 /d. A comparison of the transmissivity estimates indicate estimates typically are within an order of magnitude. The heat-pulse flowmeter methods used in this investigation to determine transmissivity of the boreholes and the individual fractures measure only the upper two or three orders of magnitude of transmissivity. Hence, other fractures in these boreholes permit the movement of water; their transmissivities, however, are lower than the detection limits of the methods that were used for this investigation and very small compared to the transmissive fractures that were studied. The data collected in this investigation were used to design discrete-zone monitoring systems for four of the boreholes used for monitoring. The results of the investigation are useful for refining the conceptual site model of ground-water flow, and for providing critical information for interpreting the results of water-quality sampling.

Connecticut↗

USGS1976

Geohydrology of the Albin and La Grange areas, aoutheastern Wyoming

The Albin and La Grange areas in southeastern Wyoming are two adjoining different hydrologic areas. Since ground water is the only source of water for irrigation in the Albin area, 34 irrigation wells have been drilled since 1968 and developed in conjunction mostly with center-pivot sprinkler systems that in 1974 irrigated about 6,980 acres. Most irrigation wells are developed in channel deposits of the Ogallala Formation of late Miocene. Water levels in parts of these channel deposits have declined about 4 to 7 feet since pumping began in 1968. In the La Grange area, lands are irrigated by surface water, ground water or a combination of both. The best producing wells are those completed in both the Brule Formation of Oligocene age and the alluvium. Secondary porosity was located and elevated in the Brule using caliper logs, an Acoustic Borehole Televiewer and geophysical logs. From the spring of 1970 to the spring of 1974, hydrographs of wells in parts of the La Grange area show water-level rises of about 5 feet resulting from the net effect of surface-water recharge and groundwater pumpage. Throughout the La Grange area no significant annual water-table declines have occurred. It is unlikely that irrigation wells pumping near Horse Creek have caused significant direct streamflow depletion.

Wyoming↗

USGS1976

High-resolution seismic reflection profiling for mapping shallow aquifers in Lee County, Florida

High-resolution continuous seismic reflection profiling equipment was utilized to define the configuration of sedimentary layers underlying part of Lee County, Florida. About 45 miles (72 kilometers) of profile were made on the Caloosahatchee River Estuary and San Carlos Bay. Two different acoustic energy sources, a high resolution boomer and a 45-electrode high resolution sparker, both having a power input of 300 joules, were used to obtain both adequate penetration and good resolution. The seismic profiles show that much of the strata of middle Miocene to Holocene age apparently are extensively folded but not faulted. Initial interpretations indicate that: (1) the top of the Hawthorn Formation (which contains the upper Hawthorn aquifer) has much relief due chiefly to apparent folding; (2) the limestone, sandstone, and unconsolidated sand and phosphorite, which together compose the sandstone aquifer, appear to be discontinuous; (3) the green clay unit of the Tamiami Formation contains large scale angular beds dipping eastward; and (4) numerous deeply cut alluvium-filled paleochannels underlie the Caloosahatchee River. (Woodard-USGS)

Florida↗

USGS1985

Development and testing of highway storm-sewer flow measurement and recording system

A comprehensive study and development of measuring instruments and techniques for measuring all components of flow in a storm-sewer drainage system was undertaken by the U.S. Geological Survey under the sponsorship of the Federal Highway Administration. The study involved laboratory and field calibration and testing of measuring flumes, pipe insert meters, weirs, electromagnetic velocity meters as well as the development and calibration of pneumatic-bubbler pressure transducer head measuring systems. Tracer-dilution and acoustic flow meter measurements were used in field verification tests. A single micrologger was used to record data from all the above instruments as well as from a tipping-bucket rain gage and also to activate on command the electromagnetic velocity meter and tracer-dilution systems. (Author 's abstract)

Water-Resources Investigations Report↗

USGS1988

Well construction, lithology, and geophysical logs for boreholes in Bear Creek Valley near Oak Ridge, Tennessee

Twenty-four wells were constructed at nine sites at Bear Creek Valley to provide geologic and hydrologic information. Lithologic samples and suits of geophysical logs were obtained from the deepest boreholes at six of the sites. Two of these boreholes at the base of Chestnut Ridge were completed in the Maynardville Limestone and two were completed in the Nolichucky Shale. Two boreholes along Pine Ridge were completed in the Rome Formation. Zones of similar lithology within a borehole were delineated from rock cutting refined by examination of geophysical logs. The contact between the Maynardville Limestone and Nolichucky Shale was identified in two of the boreholes. Fractures and cavities were readily identifiable on the acoustic-televiewer and caliper logs. Distinct water-bearing intervals were also identified from the temperature, fluid resistance, and resistivity logs. Depths at which the drilling encounterd a thrust were identified in two boreholes in the Rome Formation from both rock cutting and geophysical logs.

Tennessee↗

USGS1990

A method to estimate canal leakage to the Biscayne Aquifer, Dade County, Florida

The leakage characteristics of channels that partially penetrate the Biscayne aquifer and have reduced bed permeability were studied. Leakage characteristics were described in terms of a reach transmissivity-defined as the volume flow rate out of the channel per unit length of the channel per unit drawdown, where drawdown is defined as the difference in altitude between the water surface in the canal and the water table in the adjacent aquifer. A theoretical expression was developed to relate the reach transmissivity to the transmissivity of the formation, mean channel width, distance of drawdown measurement from the channel centerline, ratio of drawdowns on both sides of the channel, and local reach transmissivity associated with reduced bed permeability. This theoretical expression was verified using a fine-scale numerical model, which gave accurate results when drawdowns were measured beyond 10 aquifer depths from the side of the channel. Using the theoretical formulation, it is shown that the reach transmissivity employed in regional ground-water models, which are based on average drawdowns within a cell, depends on the size of the cell as well as the transmissivity of the formation, channel width, and local reach transmissivity due to reduced bed permeability. The theoretical reach transmissivity function was compared with field measurements at L-31N Canal and Snapper Creek Extension Canal in Dade County, Florida. Analyses of the data for both canals showed good agreement between the estimated and measured reach transmissivities. At L- 31N Canal, field measurements indicated that the local reach transmissivity was relatively uniform over a 2-mile reach of the channel (averaging 630 cubic feet per second per mile per foot), and the formation transmissivity was 1.8 x106 feet squared per day. At Snapper Creek Extension Canal, an approximate analysis was necessary due to the inability of the acoustic velocity meter to measure very low water velocities in the channel. Assuming an aquifer transmissivity of 1 x 106 feet squared per day, drawdown measurements indicated that the local reach transmissivity was about 400 cubic feet per second per mile per foot. The theoretical relation, combined with the local reach transmissivity and formation transmissivity, was sufficient to predict the leakage out of L-31N Canal and Snapper Creek Extension Canal for any drawdown scenario.

Florida↗

USGS1994

Geohydrology and ground-water quality in the vicinity of a ground-water-contamination site in Rockford, Illinois

A geohydrologic investigation was performed by the U.S. Geological Survey, in cooperation with the U.S. Environmental Protection Agency, to determine the distribution of volatile organic compounds in a fractured-rock aquifer near the Southeast Rockford Groundwater Contamination Site in Rockford, Ill. The geologic units of concern are the St. Peter Sandstone and Glenwood Formation; the dolomites of the Platteville and Galena Groups of Ordovician age; and the sands, gravels, silts, and clays of Quaternary age. The hydraulic units of concern are the unconsolidated aquifer, composed of sand and gravel; the fractured- dolomite aquifer, composed of the Galena and Platteville Groups and the dolomitic sections of the Glenwood Formation; and the sandstone aquifer, composed of the St. Peter Sandstone and the sandstone beds in the Glenwood Formation. The dolomite aquifer is well connected hydraulically to the overlying unconsolidated aquifer and the underlying sandstone aquifer. Caliper and acoustic-televiewer logs show several subhorizontal fractures in the dolomite that can be correlated throughout the study area. Comparison of televiewer and flowmeter logs indicates that most of the flow in the dolomite aquifer is through these fractures. Ground-water flow through two of the fractures can be correlated over large parts of the study area. Volatile organic compounds, in concentrations exceeding 2,000 micrograms per liter, were detected within the entire thickness of the dolomite aquifer where flow is measurable. Volatile organic compounds were detected in an area of the aquifer where they were thought to be absent in previous investigations.

Illinois↗