Search USGS⌕ Search

SEARCH · Search USGS

Results for “Frontiers for Young Minds”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

1,406 records · Page 7Linked to original sources
USGS2023

WellSTIC: A cost-effective sensor for performing point dilution tests to measure groundwater velocity in shallow aquifers

Many individual measurement points are required to characterize groundwater velocity within an aquifer. Groundwater velocity is most commonly measured using a network of >5 cm diameter monitoring wells, which, if not already present at a site, are expensive and labor-intensive to install. Drive-point piezometers—simple, cost-effective wells that can be installed by hand—are a common tool for sampling groundwater in shallow, alluvial aquifers, but most groundwater velocity measurement techniques require equipment that is too large for these narrow (usually <2 cm inside diameter) piezometers. In this technical note, we introduce a low-cost sensor and well packer system (<$90 USD) for performing point dilution tests in narrow piezometers. Field data show that the magnitude of groundwater velocity measured with this technique agrees with velocities computed from natural gradient tracer tests. Additionally, with proper calibration, these sensors can be used to continuously monitor in-well specific conductance, either during inter-well tracer tests with saline tracers or for water quality monitoring. This system is a viable tool for rapid assessment of the magnitude of groundwater velocity in shallow aquifers.

Water Resources Research↗
USGS2026

Standardized method for logging drill core at the Idaho National Laboratory, Idaho

The U.S. Geological Survey’s (USGS) Lithologic Core Storage Library (CSL) at the Idaho National Laboratory stores more than 120,000 feet of drill core that is accessible to the public for research and sampling. To effectively convey the physical and descriptive properties of the drill core, USGS staff at the Idaho National Laboratory Project Office log the drill core and publish the lithologic logs as data releases. The logs provide essential data on the lithology, texture, mineralogy, alteration, and other physical properties of the core, which serve as valuable information for researchers to guide their research and sampling efforts. To ensure consistent, quality, and dependable lithologic logs, this document outlines the procedures and expectations for logging drill core at the CSL. This document describes the processes for storing, photographing, and logging core, and includes a variety of resources, reference materials, and appendixes designed to standardize and aid the logging process. Following the procedures outlined in this document will produce consistent, detailed logs that facilitate dependable observations and serve as an easy reference for researchers and other interested parties.

Idaho↗
USGS2024

Current status of the community sensor model standard for the generation of planetary digital terrain models

The creation of accurate elevation models (topography) from stereo images are critical for a large variety of geospatial activities, including the production of digital orthomosaics, change detection, landing site analysis, geologic mapping, rover traverse planning, and spectral analysis. The United Stated Geological Survey, Astrogeology Science Center, continues to transition the supported planetary sensor models to the Community Sensor Model (CSM) standard. This paper describes the current state of use for this photogrammetric standard, supported sensor model types, and qualitatively compares derived topography between SOCET SET and SOCET GXP ( ® BAE Systems) using HiRISE stereo images of Mars. Our transition to the CSM standard will ensure an uninterrupted capability to make these valuable products for Mars and many other extraterrestrial planets and moons.

Remote Sensing↗
USGS2000

Assessment of potential for natural attenuation of chlorinated ethenes and ethanes in ground water at a petrochemical reclamation site, Harris County, Texas

Redox conditions in the Numerous Sand Channels Zone beneath a petrochemical reclamation site in Harris County, Texas, range from sulfate reducing to methanogenic as indicated by the presence of methane in ground water and the range of molecular hydrogen concentrations. Assessment of the potential for reductive dechlorination using BIOCHLOR as a screening tool indicated conditions favoring anaerobic degradation of chlorinated organic compounds in the Numerous Sand Channels Zone. Evidence supporting reductive dechlorination includes apparently biogenic cis -1,2-dichloroethene; an increased ratio of 1,2-dichloroethane to 1,1,2-trichloroethane downgradient from the assumed contaminant source area; ethene and methane concentrations greater than background concentrations within the area of the contaminant plume; and a positive correlation of the ratio of ethene to vinyl chloride as a function of methane concentrations. The body of evidence presented in this report argues for hydrogenolysis of trichloroethene to cis -1,2-dichloroethene; of 1,1,2-trichloroethane to 1,2-dichloroethane; and of vinyl chloride to ethene within the Numerous Sand Channels Zone. Simulations using BIOCHLOR yielded apparent first-order decay constants for reductive dechlorination in the sequence tetrachloroethene trichloroethene cis -1,2-dichloroethene vinyl chloride ethene within the range of literature values reported for each compound and apparent first-order decay constants for reductive dechlorination in the sequence 1,1,2-trichloroethane 1,2-dichloroethane slightly greater than literature values reported for each compound along the upgradient segment of a simulated ground-water flowpath. Except for vinyl chloride, apparent rates of reductive dechlorination for all simulated species show a marked decrease along the downgradient segment of the simulated ground-water flowpath. Evidence for reductive dechlorination of chlorinated ethenes within the Numerous Sand Channels Zone indicates potential for natural attenuation of chlorinated ethenes. Reductive dechlorination of chlorinated ethanes apparently occurs to a lesser extent, indicating relatively less potential for natural attenuation of chlorinated ethanes. Additional data are needed on the concentrations and distribution of chlorinated ethenes and ethanes in individual fine sand intervals of the Numerous Sand Channels Zone. This information, combined with lower minimum reporting levels for future chloroethane analyses, might enable a more complete and quantitative assessment of the potential for natural attenuation at the site.

Texas↗
USGS2024

Slip rate for the Rose Canyon fault through San Diego, California, based on analysis of GPS data: Evidence for a potential Rose Canyon–San Miguel-Vallecitos fault connection?

The Rose Canyon fault is the southern extension of the larger Newport–Inglewood–Rose Canyon fault system, which represents a major structural boundary in the Inner Continental Borderland (ICB) offshore of southern California. Ten to fifteen percent of total plate boundary motion in southern California is thought to be accommodated by the faults of the ICB, but the exact distribution of slip is uncertain. With an onshore segment, the Rose Canyon fault offers an opportunity to measure the slip rate using traditional geodetic methods. In this study, we use Global Positioning System (GPS) surface velocities from a combined campaign and continuous GPS network to constrain elastic models of the Rose Canyon fault. We then compare the observed surface velocities with proposed conceptual models of regional fault connections that facilitate the transfer of slip into the Rose Canyon fault to assess how well the observations are explained by the models. The results of elastic half‐space models suggest that the Rose Canyon fault may be slipping toward the higher end of geologic estimates, with the preferred model indicating a slip rate of 2.4 ± 0.5 mm/yr. Although limited in terms of near‐fault benchmarks, we find an improved model fit using an asymmetrical elastic half‐space model and a higher slip rate, suggesting a potential rheological contrast across the Rose Canyon fault, similar to observations from the northern Newport–Inglewood fault segments. Observed GPS surface velocities, background seismicity, and gravity anomalies south of San Diego Bay point toward a more easterly trace for the Rose Canyon fault, suggesting a possible connection with the San Miguel–Vallecitos fault system. Such a connection could increase the potential rupture lengths of future earthquakes and have important consequences for regional seismic hazards.

California↗
USGS2024

Developments in African industrial minerals for renewable energy

Introduction Africa is emerging as a leading source for minerals used in the manufacture of batteries for electric vehicles and in other renewable energy applications. New graphite, lithium, and rare-earth mines have or could be opened in African countries from 2017 through 2026. Estimates of production capacities for graphite, lithium, and rare-earth mines for 2023 and beyond are based upon supply-side assumptions, such as announced plans for new capacity construction and bankable feasibility studies, as well as projected trends that could affect current producing facilities in 2023 and planned new facilities projected to come online by 2026. Forward-looking information, including estimates of future production capacities, graphite flake distributions, and timing of the start of operations, are subject to risk factors and uncertainties that could cause actual events or results to differ significantly from expected outcomes. Projects listed in this report are presented as an indication of industry plans and are not a U.S. Geological Survey (USGS) prediction of what will take place. Only projects with planned startup dates are included in this report; ther graphite, lithium, and rare-earth projects in Africa without startup dates were known to be in various stages of development but are not included in this fact sheet.

Fact Sheet↗
USGS2024

Case definitions for wildlife diseases

Welcome to the first manual of “Case Definitions for Wildlife Diseases,” a “living” electronic publication. The plan is to add and update this manual’s case definitions periodically as warranted; thus, this manual will never be completed, and readers should download the latest versions of specific chapters (that is, definitions) when available. Constructive suggestions from readers are welcome and will help guide adjustments as this project progresses. The purpose of this manual is to provide case definitions for selected diseases of importance to wildlife in Canada and the United States. Case definitions provide standard sets of criteria for classifying the degree of certainty of a particular diagnosis and help improve surveillance data quality and comparability. Better data and standardization allow for improved data sharing, which increases geographic and species surveillance coverage and permits more robust analyses. The definitions included in this manual have been developed by veterinary pathologists, epidemiologists, and wildlife biologists primarily from the U.S. Geological Survey National Wildlife Health Center (NWHC) and Canadian Wildlife Health Cooperative (CWHC). Pathologists from each organization reviewed and finalized the definitions. Each case definition has been peer reviewed by two scientific experts before publication. This manual begins with the case definition template. This generic template includes four sections: “Individual, Place, and Time Criteria for Diagnosis and Testing,” “Field Criteria for Diagnosis,” “Laboratory Criteria for Diagnosis,” and “Epidemiological Linkage Criteria for Diagnosis” and can be used to guide development of new case definitions. Information in each section is then combined to provide an overall case classification. Disease diagnoses are classified as “Confirmed,” “Presumptive,” or “Suspected;” and evidence of a pathogen or toxin is classified as “Exposed” or “Present/Detected.” Each subsequent chapter is then a case definition for a specific disease of wildlife, and infectious and non-infectious diseases are included.

Techniques and Methods↗
USGS1984

Techniques for estimating magnitude and frequency of floods on streams in Indiana

Equations are presented for estimating the magnitude and frequency of floods at ungaged sites on unregulated and nonurban streams in Indiana. The equations were developed by multiple-regression, analysis of basin characteristics and peak-flow statistical data from 242 gaged locations in Indiana, Ohio, and Illinois. The State of Indiana was divided into seven areas on the basis of the regression analysis. A set of equations for estimating peak discharges with recurrence intervals of 2, IO, 25, 50, and 100 years was developed for each area. Significant basin characteristics in the equations are drainage area, channel length, channel slope, mean annual precipitation, storage, precipitation intensity, and a runoff coefficient. Standard errors of estimate for the equations range from 24 to 45 percent. Methods are also presented for estimating flood magnitude and frequency at sites on gaged streams. Flood-frequency data based on observed peaks are given for 270 gaged locations. Twenty of these are on regulated streams, and six are on urban streams. Basin characteristics are also included car 245 of the gaged locations on unregulated and nonurban streams. No techniques are given for estimating flood magnitude and frequency at ungaged sites on regulated or urban streams. A rainfall-runoff model was tlsed to synthesize long-term peak data at 11 gaged locations on small streams. Flood-frequency curves developed from the long-term synthetic data were combined with curves based on short-term observed data to provide weighted estimates of flood magnitude and frequency at the rainfall-runoff stations.

Indiana↗
USGS2024

Getting to the surface of the problem: A dynamic rupture benchmark for shallowly dipping faults near Earth’s surface

The Statewide California Earthquake Center (SCEC) Dynamic Rupture Group workshop “Getting to the Surface of the Problem: A Dynamic Rupture Benchmark for Shallowly-Dipping Faults Near Earth’s Surface” was convened virtually, in an online meeting on November 4, 2024. 52 people participated, including two who sent pre-recorded lightning talks earlier, but were unable to join us that day due to the international time-zone difference. One-half of our participants were students or postdocs, and the group included scientists from 11 countries (USA, Canada, China, Czech Republic, France, Germany, Iceland, Japan, New Zealand, Saudi Arabia, Switzerland).

Final Report↗
USGS2025

A model uncertainty quantification protocol for evaluating the value of observation data

The history-matching approach to parameter estimation with models enables a powerful offshoot analysis of data worth—using the uncertainty of a model forecast as a metric for the worth of data. Adding observation data will either have no impact on forecast uncertainty or will reduce it. Removing existing data will either have no impact on forecast uncertainty or will increase it. The history-matching framework makes it possible to perform this quantitative analysis leveraging the connections among observations, model parameters, and model forecasts. We show this behavior on a specific groundwater flow model of the Mississippi Alluvial Plain and show where the analysis can be informative for considering the potential design of an observation network based on existing or potential observations.

Scientific Investigations Report↗
USGS2024

Framework for implementing damping scaling factors in U.S. Geological Survey National Seismic Hazard Models

Traditionally, probabilistic seismic hazard analysis (PSHA) has focused on calculating ground motion hazard curves for elastic, 5%-damped pseudo spectral accelerations, Sa(T,5%), which are used as the basis for engineering design parameters and targets for ground motion selection and modification. However, structures and geotechnical systems can exhibit a wide range of damping ratios both above and below the 5% level, depending on the construction material, structural system, nonstructural elements, or subsurface soil properties. When spectral parameters at such damping levels are required for certain applications, 5%-damped accelerations have traditionally been extracted from PSHA-based hazard curves and adjusted outside of the hazard integral using damping scaling factors (DSF) such as those from Newmark & Hall (1982). Recent advances in the development of more rigorous and comprehensive damping scaling models (e.g., Rezaeian et al., 2014; Rezaeian et al., 2021) have allowed for the modeling of means and standard deviations of DSFs as functions of earthquake source and path properties for crustal, intraslab, and subduction interface tectonic environments. These DSF models can be applied to ground motion model (GMM) estimates of Sa(T,5%) for a given earthquake rupture scenario to produce a corresponding mean and standard deviation Sa at a specified damping ratio β, Sa(T,β). In this study, the DSF models of Rezaeian et al. (2014) and Rezaeian et al. (2021) are implemented within the U.S. Geological Survey National Seismic Hazard Model (NSHM) PSHA framework to calculate probabilistic hazard curves for spectral accelerations at damping ratios from 0.5% to 30%. The DSF models are applied directly to the mean and standard deviation of Sa(T,5%) predictions from each GMM in the NSHM logic tree. Resulting hazard curves and uniform hazard and risk spectra for Sa(T,β) are presented for several geographic locations and compared with corresponding spectra estimated using current design practices by applying the same DSFs outside of the PSHA calculation. Key differences between the two methods for estimating Sa(T,β) are discussed, and potential strategies are presented for the implementation and usage of the hazard-consistent Sa(T,β) in building codes. Comparing the results to those from DSFs used in current design practices that are mainly based on Newmark & Hall (1982) is not explored in this study.

Conference Paper↗
USGS2026

A process-based model for forecasting wave runup along the coast of Georgia

Wave runup is an important nearshore process that impacts total water level, sediment transport, and coastal design. Current methods for forecasting wave runup implement an empirical model that considers offshore wave height, wave period, and generalized beach slope. In this study, the authors generated wave runup forecasts from offshore wave conditions and a system of polynomial equations derived from numerical simulations at three different still water datums for each beach profile. They developed a process-based methodology that incorporated site-specific cross-shore topobathy into the phase-resolving numerical model. A comparison between the system of equations, deterministic hydrodynamic simulations, and observed high-water marks was made using Hurricanes Matthew (2016) and Irma (2017) for 12 cases, and it showed that the polynomials were capable of being consistent with the results from full simulation runs, while not requiring hours of runtime when a forecast was needed—the differences between the polynomial and the observed high water marks ranged from 3 to 32 cm for the Irma hindcast and 9–70 cm for Matthew. Then, using forcings from Hurricanes Ian and Nicole (2022), the model predicted the occurrence of dune collision, overwash, and inundation for the coast of Georgia and suggested that wave runup was impacted by the still water level and local topobathy.

Georgia↗
USGS1990

Recharge rates and aquifer hydraulic characteristics for selected drainage basins in middle and east Tennessee

Quantitative information concerning aquifer hydrologic and hydraulic characteristics is needed to manage the development of ground-water resources. These characteristics are poorly defined for the bedrock aquifers in Middle and East Tennessee where demand for water is increasing. This report presents estimates of recharge rate, storage coefficient, diffusivity, and transmissivity for representative drainage basins in Middle and East Tennessee, as determined from analyses of stream-aquifer interactions. The drainage basins have been grouped according to the underlying major aquifer, then statistical descriptions applied to each group, in order to define area1 distribution of these characteristics. Aquifer recharge rates are estimated for representative low, average, and high flow years for 63 drainage basins using hydrograph analysis techniques. Net annual recharge during average flow years for all basins ranges from 4.1 to 16.8 in/yr (inches per year), with a mean value of 7.3 in. In general, recharge rates are highest for basins underlain by the Blue Ridge aquifer (mean value11.7 in/yr) and lowest for basins underlain by the Central Basin aquifer (mean value 5.6 in/yr). Mean recharge values for the Cumberland Plateau, Highland Rim, and Valley and Ridge aquifers are 6.5, 7.4, and 6.6 in/yr, respectively. Gravity drainage characterizes ground-water flow in most surficial bedrock aquifer in Tennessee. Accordingly, a gravity yield analysis, which compares concurrent water-level and streamflow hydrographs, was used to estimate aquifer storage coefficient for nine study basins. The basin estimates range from 0.002 to 0.140; however, most estimates are within a narrow range of values, from 0.01 to 0.025. Accordingly, storage coefficient is estimated to be 0.01 for all aquifers in Middle and East Tennessee, with the exception of the aquifer in the inner part of the Central Basin, for which storage coefficient is estimated to be 0.002. Estimates of aquifer hydraulic diffusivity are derived from estimates of the streamflow recession index and drainage density for 75 drainage basins; values range from 3,300 to 130,000 ft^2/d (feet squared per day). Basin-specific and site-specific estimates of transmissivity are computed from estimates of hydraulic diffusivity and specific-capacity test data, respectively. Basin-specific, or areal, estimates of transmissivity range from 22 to 1,300 ft^2/d, with a mean of 240 ft^2/d In general, areal transmissivity is highest for basins underlain by the Cumberland Plateau aquifer (mean value 480 ft^2/d) and lowest for basins underlain by the Central Basin aquifer (mean value 79 ft^2/d). Mean transmissivity values for the Highland Rim, Valley and Ridge, and Blue Ridge aquifer are 320,140, and 120 ft^2/d respectively. Site-specific estimates of transmissivity, computed from specific-capacity data from 118 test wells in Middle and East Tennessee range from 2 to 93,000 ft^2/d with a mean of 2,600 ft^2/d Mean transmissivity values for the Cumberland Plateau, Highland Rim, Central Basin, Valley and Ridge, and Blue Ridge aquifers are 2,800,1,200, 7,800, 390, and 65Oft Id, respectively.

Tennessee↗
USGS2025

Case study of deep learning image segmentation for the purposes of rapid 2D petrographic analysis in volcanic rocks

Automation using deep learning methods is a useful alternative to manual methods of petrographic segmentation, but often requires user familiarity with coding and/or algorithms. We examine the Dragonfly TM program's deep learning tools for application by users with a variety of skill levels as a method for petrographic image segmentation. An image processing methodology, bimodal image stacking, was created for low-input-data, high-efficacy training of models which can then be applied to varied samples. Using backscatter electron images we show that the resulting model segmentations agree with manual segmentation total and modal crystallinity values within 5%, and calculated plagioclase crystal size distribution (CSD) values within 2σ, despite limitations in discriminating mafic phases. Model creation and training takes <24 hours, 1–3 hours of which are supervised, and the resultant model can then be applied to new uncharacterized samples in <15 minutes per image. This allows for non-experts to create and utilize deep learning models to segment images of variable brightness and texture, at low user-time cost and resulting in size and shape data which are within uncertainty of manual segmentation. While some limitations are noted (for example, sieve-textured phases may need manual correction, and different minerals with similar BSE intensity may not be resolved as separate phases), this methodology can be utilized for general application of models to wide ranges of volcanic crystalline and bubble textures, and to create a library of models for rapid petrological analysis during volcanic eruptions.

Alaska↗
USGS2025

Enhanced geothermal systems electric-resource assessment for the Great Basin, southwestern United States

The U.S. Geological Survey recently (2025) completed a provisional assessment of the geothermal-electric resources associated with high-temperature, low-permeability rock formations of the Great Basin, Southwestern United States. If sufficient technological advances to commercialize enhanced geothermal systems occur, then a current best provisional estimate for electric-power generation capacity of 135 gigawatts electric are available from the upper 6 kilometers of the Earth’s crust. This estimate is a potential substantial increase of the installed geothermal electricity-generating capacity from <1 to 10 percent of current total U.S. power production capacity.

California, Idaho, Nevada, Oregon, Utah↗
USGS1976

Technique for estimating magnitude and frequency of floods in Kentucky

This report presents flood magnitude and frequency relations applicable to unregulated streams in Kentucky. The relations are based on flood data at 117 gaging stations in Kentucky and 14 in adjacent states having 10 or more years of record not significantly affected by man-made changes. Equations that relate flood magnitude and frequency to contributing drainage area in 16 geographic areas may be used to estimate magnitude of future floods with recurrence intervals of as much as 100 years on gaged and ungaged streams having drainage areas of 10 to 4,300 square miles (25 .9 to 11,100 square kilometers) . Estimating equations are also presented in graphical form for the convenience of the user. Additional graphs are presented to estimate flood magnitude for selected recurrence intervals along the Cumberland, Kentucky, and Ohio Rivers.

Kentucky↗
USGS1996

Technique for estimating magnitude and frequency of peak flows in Maryland

A convenient and reliable technique for estimating flood magnitudes is required for effective flood-plain management and for the efficient design of bridges, culverts, embankments, and flood-protection structures. Methods are presented for estimating peak-flow magnitudes of selected frequencies, ranging from 2 to 500 years, for all nontidal drainage basins in Maryland. The methods were developed by generalized least-squares regression techniques using data from 219 gaged basins in and near Maryland. The State is divided into five hydrologic regions: the Appalachian Plateaus and Allegheny Ridges region, the Blue Ridge and Great Valley region, the Piedmont region, the Western Coastal Plain region, and the Eastern Coastal Plain region. These regions correspond to the physiographic provinces of the State, with the exceptions that (1) the Coastal Plain Province is divided into two hydrologic regions, and (2) there is no distinct hydrologic region corresponding to the Valley and Ridge Province as it is divided into its constituent Allegheny Ridges and Great Valley subdivisions. Sets of equations for calculating peak discharges based on physical basin characteristics are provided for each of the regions. Based on the peak-flow equations, methods for estimating peak flows are presented for ungaged and gaged streams in Maryland. The methods and equations are supported by generalized least-squares analysis of basin and flood-frequency characteristics data from 219 drainage basins in and near Maryland. estimates for each of the five regions are calculated using combinations of the fol-lowing basin characteristics: drainage area, forest cover, basin relief, carbonate rock coverage, storage, and runoff-curve number. Drainage area contributes to the estimate in all five study regions. Carbonate rock coverage is used only in the Blue Ridge and Great Valley region. Storage and runoff-curve number are used solely in the Eastern Coastal Plain region. All other basin characteristics are used in two or more regions. Standard errors of estimate for the regression equations range from 19 to 31 percent in the Appalachian Plateaus and Allegheny Ridges region, 34 to 47 percent in the Blue Ridge and Great Valley region, 33 to 48 percent in the Piedmont region, 45 to 64 percent in the Western Coastal Plain region, and 36 to 42 percent in the Eastern Coastal Plain region.

Maryland↗
USGS2025

Extracting data from maps: Lessons learned from the artificial intelligence for critical mineral assessment competition

The U.S. Geological Survey (USGS), Defense Advanced Projects Research Agency (DARPA), NASA Jet Propulsion Laboratory (JPL), and MITRE ran a 12-week machine learning competition aimed at accelerating development of AI tools for critical mineral assessments. The Artificial Intelligence for Critical Mineral Assessment Competition solicited innovative solutions for two challenges: 1) automated georeferencing of historical maps, and 2) automated feature extraction from historical maps. Competitors used a new dataset of historical map images to train, validate, and evaluate their models. Automated georeferencing pipelines attained a median root-mean square error of 1.1 km. Prompt-based extraction (i.e., with user input) of polygons, polylines, and points from geologic maps yielded median F1-scores of 0.77, 0.56, 0.35, respectively. Geologic maps pose numerous challenges for AI workflows because they vary significantly. However, despite its short duration, the competition yielded promising results that have since spurred further innovation in this area and led to the development of new AI tools to semi-automate key, time-consuming parts of the assessment workflow.

Applied Computing and Geosciences↗