SEARCH · Search USGS

Results for “Analytical Methods”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,171 records · Page 65Linked to original sources

USGS2016

Groundwater contaminant plume maps and volumes, 100-K and 100-N Areas, Hanford Site, Washington

This study provides an independent estimate of the areal and volumetric extent of groundwater contaminant plumes which are affected by waste disposal in the 100-K and 100-N Areas (study area) along the Columbia River Corridor of the Hanford Site. The Hanford Natural Resource Trustee Council requested that the U.S. Geological Survey perform this interpolation to assess the accuracy of delineations previously conducted by the U.S. Department of Energy and its contractors, in order to assure that the Natural Resource Damage Assessment could rely on these analyses. This study is based on previously existing chemical (or radionuclide) sampling and analysis data downloaded from publicly available Hanford Site Internet sources, geostatistically selected and interpreted as representative of current (from 2009 through part of 2012) but average conditions for groundwater contamination in the study area. The study is limited in scope to five contaminants—hexavalent chromium, tritium, nitrate, strontium-90, and carbon-14, all detected at concentrations greater than regulatory limits in the past. All recent analytical concentrations (or activities) for each contaminant, adjusted for radioactive decay, non-detections, and co-located wells, were converted to log-normal distributions and these transformed values were averaged for each well location. The log-normally linearized well averages were spatially interpolated on a 50 × 50-meter (m) grid extending across the combined 100-N and 100-K Areas study area but limited to avoid unrepresentative extrapolation, using the minimum curvature geostatistical interpolation method provided by SURFER ® data analysis software. Plume extents were interpreted by interpolating the log-normally transformed data, again using SURFER ® , along lines of equal contaminant concentration at an appropriate established regulatory concentration . Total areas for each plume were calculated as an indicator of relative environmental damage. These plume extents are shown graphically and in tabular form for comparison to previous estimates. Plume data also were interpolated to a finer grid (10 × 10 m) for some processing, particularly to estimate volumes of contaminated groundwater. However, hydrogeologic transport modeling was not considered for the interpolation. The compilation of plume extents for each contaminant also allowed estimates of overlap of the plumes or areas with more than one contaminant above regulatory standards. A mapping of saturated aquifer thickness also was derived across the 100-K and 100–N study area, based on the vertical difference between the groundwater level (water table) at the top and the altitude of the top of the Ringold Upper Mud geologic unit, considered the bottom of the uppermost unconfined aquifer. Saturated thickness was calculated for each cell in the finer (10 × 10 m) grid. The summation of the cells’ saturated thickness values within each polygon of plume regulatory exceedance provided an estimate of the total volume of contaminated aquifer, and the results also were checked using a SURFER ® volumetric integration procedure. The total volume of contaminated groundwater in each plume was derived by multiplying the aquifer saturated thickness volume by a locally representative value of porosity (0.3). Estimates of the uncertainty of the plume delineation also are presented. “Upper limit” plume delineations were calculated for each contaminant using the same procedure as the “average” plume extent except with values at each well that are set at a 95-percent upper confidence limit around the log-normally transformed mean concentrations, based on the standard error for the distribution of the mean value in that well; “lower limit” plumes are calculated at a 5-percent confidence limit around the geometric mean. These upper- and lower-limit estimates are considered unrealistic because the statistics were increased or decreased at each well simultaneously and were not adjusted for correlation among the well distributions (i.e., it is not realistic that all wells would be high simultaneously). Sources of the variability in the distributions used in the upper- and lower-extent maps include time varying concentrations and analytical errors. The plume delineations developed in this study are similar to the previous plume descriptions developed by U.S. Department of Energy and its contractors. The differences are primarily due to data selection and interpolation methodology. The differences in delineated plumes are not sufficient to result in the Hanford Natural Resource Trustee Council adjusting its understandings of contaminant impact or remediation.

Washington↗

USGS2022

Can machine learning accelerate process understanding and decision-relevant predictions of river water quality?

The global decline of water quality in rivers and streams has resulted in a pressing need to design new watershed management strategies. Water quality can be affected by multiple stressors including population growth, land use change, global warming, and extreme events, with repercussions on human and ecosystem health. A scientific understanding of factors affecting riverine water quality and predictions at local to regional scales, and at sub-daily to decadal timescales are needed for optimal management of watersheds and river basins. Here, we discuss how machine learning (ML) can enable development of more accurate, computationally tractable, and scalable models for analysis and predictions of river water quality. We review relevant state-of-the art applications of ML for water quality models and discuss opportunities to improve the use of ML for emerging computational and mathematical methods for model selection, hyperparameter optimization, incorporating process knowledge into ML models, improving explainablity, uncertainty quantification, and model-data integration. We then present considerations for using ML to address water quality problems given their scale and complexity, available data and computational resources, and stakeholder needs. When combined with decades of process understanding, interdisciplinary advances in knowledge-guided ML, information theory, data integration, and analytics can help address fundamental science questions and enable decision-relevant predictions of riverine water quality.

Hydrological Processes↗

USGS2025

Leveraging invasive mussel contaminant survey data for stepwise prioritization of chemicals of potential concern in the Great Lakes basin

Historical and ongoing anthropogenic activities coupled with advancements in analytical techniques have led to the detection of large numbers of contaminants in the Laurentian Great Lakes. Consequently, identifying and prioritizing chemicals likely to cause ecological harm represents a challenge for natural resource managers. Previous prioritization efforts have focused on contaminants in sediment, water, and passive samplers, which may not be representative of compounds that bioaccumulate in aquatic organisms. Consequently, this study adopted a stepwise method to prioritize chemicals of potential concern detected in dreissenid mussels from samples collected across the Great Lakes from 2009–2018. The stepwise method considered environmental fate, detection frequency, and exceedance of toxicity quotients based on ecotoxicological effect concentrations. Overall, 153 compounds out of 267 analyzed were detected in dreissenid mussels, 47 of which had water quality effect concentrations, 56 had apical effect concentrations (Tier 1 ECOTOX or apical screening), 17 had nonapical effect concentrations (Tier 2 ECOTOX, Cytotoxic Burst, and ToxCast) and 33 had estimated effect concentrations (quantitative structure-activity relationship, estimated screening, and pharmacological potency). Of the compounds with water quality effect concentrations, nine were designated as high priority, including the herbicide atrazine and five polycyclic aromatic hydrocarbons that were previously identified as potentially hazardous within other matrices. Similar contaminants were identified as high priority in a related study of native unionid mussels in the Great Lakes. A total of 27 compounds were low priority, suggesting that these contaminants do not warrant further action based on this dataset. Overall, these findings will facilitate the development of management strategies to mitigate the effects of contaminants on aquatic organisms within the Great Lakes.

Great Lakes basin↗

USGS1991

Studies of a peatified angiosperm log cross section from Indonesia by nuclear magnetic resonance spectroscopy and analytical pyrolysis

Samples from a 10 cm cross-sectional radius of a peatified angiosperm log from Sumatra, Indonesia, were examined by 13 C nuclear magnetic resonance and pyrolysis-gas chromatography in order to understand chemical changes due to the peatification process. NMR results show degradation by selective loss of carbohydrates in all parts of the log section compared with fresh wood; however, the degree of degradation is less near the center of the log section. The degree of ring substitution of aromatic lignin monomeric units, as measured by dipolar dephasing NMR methods, appears to be less at the center of the log section than at the periphery. The methoxyl carbon content of lignin in the log is lower than in unaltered angiospermous lignin but does not appear to change as a function of either radial position or the degree of aromatic ring substitution. Pyrolysis-gas chromatography indicates higher yields of catechols in the outer areas relative to the heartwood. Other than the variations in catechol contents and in the yields of carbohydrate-derived pyrolysis products (e.g. levoglucosan, angelicalactones), the pyrolysis results do not show significant changes related to radial position, indicating that the lignin is not significantly altered across the log section.

Organic Geochemistry↗

USGS2018

Effect of dynamical phase on the resonant interaction among tsunami edge wave modes

Different modes of tsunami edge waves can interact through nonlinear resonance. During this process, edge waves that have very small initial amplitude can grow to be as large or larger than the initially dominant edge wave modes. In this study, the effects of dynamical phase are established for a single triad of edge waves that participate in resonant interactions. In previous studies, Jacobi elliptic functions were used to describe the slow variation in amplitude associated with the interaction. This analytical approach assumes that one of the edge waves in the triad has zero initial amplitude and that the combined phase of the three waves φ = θ 1 + θ 2 − θ 3 is constant at the value for maximum energy exchange ( φ = 0). To obtain a more general solution, dynamical phase effects and non-zero initial amplitudes for all three waves are incorporated using numerical methods for the governing differential equations. Results were obtained using initial conditions calculated from a subduction zone, inter-plate thrust fault geometry and a stochastic earthquake slip model. The effect of dynamical phase is most apparent when the initial amplitudes and frequencies of the three waves are within an order of magnitude. In this case, non-zero initial phase results in a marked decrease in energy exchange and a slight decrease in the period of the interaction. When there are large differences in frequency and/or initial amplitude, dynamical phase has less of an effect and typically one wave of the triad has very little energy exchange with the other two waves. Results from this study help elucidate under what conditions edge waves might be implicated in late, large-amplitude arrivals.

Pure and Applied Geophysics↗

USGS1978

Remote-sensing methods for monitoring surface coal mining in the northern Great Plains

Recent studies at a large surface coal mine in southern Montana confirm that remote sensing is both feasible and effective for gathering land-use and environmental data (spatial, dynamic, and seasonal) for large-scale surface mines in the northern Great Plains. The Western Energy Co.'s Rosebud mine near Colstrip, Mont., was selected as a test site because it typifies surface operations in the Powder River Basin of Montana and Wyoming and elsewhere in the northern Great Plains. Several basic interpretive and analytical remote-sensing techniques were used to identify and delineate various categories of surface-mining operations and concurrent stages of reclamation that characterize most, if not all, such mining operations. Color infrared and black-and-white aerial photographs and a black-and-white band 5 Landsat image were used to identify (1) high wall and bench areas, (2) ungraded spoils, (3) graded and recontoured areas, (4) revegetated recontoured areas, (5) natural and impounded surface water, and (6) miscellaneous areas. Over the lifespan of an extensive surface mine, cultural and natural processes and cumulative environmental effects can be monitored by capitalizing on the close correlation between enhanced satellite imagery, infrared and (or) black-and-white aerial photography, standard large-scale topographic maps (such as U.S. Geological Survey 7½-minute quadrangle maps), and results of onsite inspection of mining and reclamation by Federal or State agencies.

Montana↗

USGS2016

Application of effective discharge analysis to environmental flow decision-making

Well-informed river management decisions rely on an explicit statement of objectives, repeatable analyses, and a transparent system for assessing trade-offs. These components may then be applied to compare alternative operational regimes for water resource infrastructure (e.g., diversions, locks, and dams). Intra- and inter-annual hydrologic variability further complicates these already complex environmental flow decisions. Effective discharge analysis (developed in studies of geomorphology) is a powerful tool for integrating temporal variability of flow magnitude and associated ecological consequences. Here, we adapt the effectiveness framework to include multiple elements of the natural flow regime (i.e., timing, duration, and rate-of-change) as well as two flow variables. We demonstrate this analytical approach using a case study of environmental flow management based on long-term (60 years) daily discharge records in the Middle Oconee River near Athens, GA, USA. Specifically, we apply an existing model for estimating young-of-year fish recruitment based on flow-dependent metrics to an effective discharge analysis that incorporates hydrologic variability and multiple focal taxa. We then compare three alternative methods of environmental flow provision. Percentage-based withdrawal schemes outcompete other environmental flow methods across all levels of water withdrawal and ecological outcomes.

Environmental Management↗

USGS2015

The U.S. Geological Survey coal quality (COALQUAL) database version 3.0

Since the mid-1970s, the U.S. Geological Survey (USGS) has maintained a coal quality database of national scope named USCHEM, which currently contains data for over 13,000 samples. A subset of the USCHEM database called COALQUAL Version 1.3 was initially published in 1994 and was followed by Version 2.0 in 1997. Version 3.0 of the COALQUAL database represents a major editing effort to resolve some of the DOS software limitations used by earlier versions of the database. Because of database size limits during the development of COALQUAL Version 1.3, many analyses of individual bench samples were merged into whole coal bed averages. The methodology for making these composite intervals was not consistent. Size limits also restricted the amount of georeferencing information and forced removal of qualifier notations such as "less than detection limit" (<) information, which can cause problems when using the data. A review of the original data sheets revealed that COALQUAL Version 2.0 was missing information that was needed for a complete understanding of a coal section. Another important database issue to resolve was the USGS "remnant moisture" problem. Prior to 1998, tests for remnant moisture (as-determined moisture in the sample at the time of analysis) were not performed on any USGS major, minor, or trace element coal analyses. Without the remnant moisture, it is impossible to convert the analyses to a usable basis (as-received, dry, etc.). Based on remnant moisture analyses of hundreds of samples of different ranks (and known residual moisture) reported after 1998, it was possible to develop a method to provide reasonable estimates of remnant moisture for older data to make it more useful in COALQUAL Version 3.0. In addition, COALQUAL Version 3.0 is improved by (1) adding qualifiers, including statistical programming to deal with the qualifiers; (2) clarifying the sample compositing problems; and (3) adding associated samples. Version 3.0 of COALQUAL also represents the first attempt to incorporate data verification by mathematically crosschecking certain analytical parameters. Finally, a new database system was designed and implemented to replace the outdated DOS program used in earlier versions of the database.

Data Series↗

USGS2010

Water quality and hydrology of the Silver River Watershed, Baraga County, Michigan, 2005-08

The Silver River Watershed comprises about 69 square miles and drains part of northeastern Baraga County, Michigan. For generations, tribal members of the Keweenaw Bay Indian Community have hunted and fished in the watershed. Tribal government and members of Keweenaw Bay Indian Community are concerned about the effect of any development within the watershed, which is rural, isolated, and lightly populated. For decades, the area has been explored for various minerals. Since 2004, several mineral-exploration firms have been actively investigating areas within the watershed; property acquisition, road construction, and subsurface drilling have taken place close to tributary streams of the Silver River. The U.S. Geological Survey, in cooperation with Keweenaw Bay Indian Community, conducted a multi-year water-resources investigation of the Silver River Watershed during 2005-08. Methods of investigation included analyses of streamflow, water-quality sampling, and ecology at eight discrete sites located throughout the watershed. In addition, three continuous-record streamgages located within the watershed provided stage, discharge, specific conductance, and water-temperature data on an hourly basis. Water quality of the Silver River Watershed is typical of many streams in undeveloped areas of Upper Michigan. Concentrations of most analytes typically were low, although several exceeded applicable surface-water-quality standards. Seven samples had concentrations of copper that exceeded the Michigan Department of Environmental Quality standards for wildlife, and one sample had concentrations of cyanide that exceeded the same standards. Concentrations of total mercury at all eight sampling sites exceeded the Great Lakes Basin water-quality standard, but the ratio of methylmercury to total mercury was similar to the 5 to 10 percent found in most natural waters. Concentrations of arsenic and chromium in bed sediments were near the threshold-effect concentration. A qualitative ecological assessment of fishes and macroinvertebrates showed that intolerant salmonids were present at most sampled sites, and macroinvertebrate communities were indicative of near-excellent or excellent conditions at all eight sites. This baseline information will aid in an ongoing monitoring effort designed to protect the water resources of the

Scientific Investigations Report↗

USGS1990

Synthetic calibration of a Rainfall-Runoff Model

A method for synthetically calibrating storm-mode parameters for the U.S. Geological Survey's Precipitation-Runoff Modeling System is described. Synthetic calibration is accomplished by adjusting storm-mode parameters to minimize deviations between the pseudo-probability disributions represented by regional regression equations and actual frequency distributions fitted to model-generated peak discharge and runoff volume. Results of modeling storm hydrographs using synthetic and analytic storm-mode parameters are presented. Comparisons are made between model results from both parameter sets and between model results and observed hydrographs. Although mean storm runoff is reproducible to within about 26 percent of the observed mean storm runoff for five or six parameter sets, runoff from individual storms is subject to large disparities. Predicted storm runoff volume ranged from 2 percent to 217 percent of commensurate observed values. Furthermore, simulation of peak discharges was poor. Predicted peak discharges from individual storm events ranged from 2 percent to 229 percent of commensurate observed values. The model was incapable of satisfactorily executing storm-mode simulations for the study watersheds. This result is not considered a particular fault of the model, but instead is indicative of deficiencies in similar conceptual models.

Conference Paper↗

USGS2002

Determination of lead, uranium, thorium, and thallium in silicate glass standard materials by isotope dilution mass spectrometry

A set of four standard glasses has been prepared which have been doped with 61 different elements at the 500-, 50-, 1-, and 0.02-ppm level. The concentrations of lead, uranium, thorium, and thallium have been determined by isotope dilution mass spectrometry at a number of points in each of the glasses. The results obtained from independent determinations in two laboratories demonstrate the homogeneity of the samples and that precision of the order of 0.5% (95% L.E.) may be obtained by the method even at the 20-ppb level for these elements. The chemical and mass spectrometric procedures necessary are presented.

Analytical Chemistry↗

USGS2020

UV identification and quantitative measurement of quinaldine residues in fish

A method for the confirmatory analysis of quinaldine residue in fish is described. The method utilizes the same extraction and cleanup procedure as the GLC method reported previously. The lower limit of sensitivity for quinaldine residue in fish muscle is 0.01 ppm. Identification is accomplished by comparing the UV spectra of the sample and a standard solution of quinaldine.

Journal of the Association of Official Analytical ↗

USGS1976

Uranium analysis of single drops of natural waters using the fission-track technique

The fission-track technique has been applied to uranium analysis of natural waters using a single drop of water. Samples may be collected in the field by evaporating a drop of water on a detector, and samples may then be analyzed by returning the detector to the laboratory. A sample collecting kit has been assembled, which facilitates the designed sampling method. Some unique advantages of this technique are picogram sensitivity (10 -12 g) for uranium on single drops of water, maintenance of sample integrity during transport and storage, and the ability to discern whether the uranium is in solution or in the suspended material. Counting the tracks is the most time-consuming part of the analysis, but it can be reduced by using automatic counting systems. The analytical error is generally ± 10 percent over the entire range of concentrations.

Open-File Report↗

USGS1951

Summary of the research work of the Trace Elements Section, Geochemistry and Petrology Branch, for the period January 1-March 31, 1951

This report summarized the research work of the Trace Elements Section, Geochemistry and Petrology Branch for the period January 1 - March 31, 1951. Work before that is summarized in an earlier report, "Summary of the research work of the Trace Elements Section, Geochemistry and Petrology Branch, for the period April 1, 1948 - December 31, 1950," by John C. Rabbitt (U.S. Geol. Survey Trace Elements Investigations Rept. 148, January 1951). This report will be referred to as TEIR 148. In TEIR 148 the purpose of each project was described and it is not thought necessary to repeat that material. The research work of the section consists of laboratory and related field studies in the following fields: 1. Mineralogic and petrologic investigations of radioactive rocks, minerals, and ores. 2. Investigations of chemical methods of analysis for uranium, thorium, and other elements and compounds in radioactive materials, and related chemical problems. 3. Investigations of spectographic method of analysis for a wide variety of elements in radioactive materials. 4. Investigation of radiometric methods of analysis is applied to radioactive materials. It should be emphasized that the work undertaken so far is almost entirely in the nature of investigations supporting the field appraisal of known uraniferous deposits. A program of more fundamental research, particularly in the mineralogy and geochemistry of uranium, is now being drawn up and will be submitted for approval soon. This report does not deal with the routine analytical work of the Section nor the public-sample program. The analytical work will be summarized in a report to be issued after the end of fiscal year 1951, and a report on the public-sample program is in process. Special thanks are due members of the Section who are engaged in the research work and who have supplied material for this report, the Early Ingerson, Chief of the Geochemistry and Petrology Branch for his critical review, to Jane Titcomb of the editorial staff of the Section for editing the report, and to Virginia Layne of the same staff, for typing the manuscript and the multilith mats.

Trace Elements Investigations↗

USGS2012

Methods for evaluating temporal groundwater quality data and results of decadal-scale changes in chloride, dissolved solids, and nitrate concentrations in groundwater in the United States, 1988-2010

Decadal-scale changes in groundwater quality were evaluated by the U.S. Geological Survey National Water-Quality Assessment (NAWQA) Program. Samples of groundwater collected from wells during 1988-2000 - a first sampling event representing the decade ending the 20th century - were compared on a pair-wise basis to samples from the same wells collected during 2001-2010 - a second sampling event representing the decade beginning the 21st century. The data set consists of samples from 1,236 wells in 56 well networks, representing major aquifers and urban and agricultural land-use areas, with analytical results for chloride, dissolved solids, and nitrate. Statistical analysis was done on a network basis rather than by individual wells. Although spanning slightly more or less than a 10-year period, the two-sample comparison between the first and second sampling events is referred to as an analysis of decadal-scale change based on a step-trend analysis. The 22 principal aquifers represented by these 56 networks account for nearly 80 percent of the estimated withdrawals of groundwater used for drinking-water supply in the Nation. Well networks where decadal-scale changes in concentrations were statistically significant were identified using the Wilcoxon-Pratt signed-rank test. For the statistical analysis of chloride, dissolved solids, and nitrate concentrations at the network level, more than half revealed no statistically significant change over the decadal period. However, for networks that had statistically significant changes, increased concentrations outnumbered decreased concentrations by a large margin. Statistically significant increases of chloride concentrations were identified for 43 percent of 56 networks. Dissolved solids concentrations increased significantly in 41 percent of the 54 networks with dissolved solids data, and nitrate concentrations increased significantly in 23 percent of 56 networks. At least one of the three - chloride, dissolved solids, or nitrate - had a statistically significant increase in concentration in 66 percent of the networks. Statistically significant decreases in concentrations were identified in 4 percent of the networks for chloride, 2 percent of the networks for dissolved solids, and 9 percent of the networks for nitrate. A larger percentage of urban land-use networks had statistically significant increases in chloride, dissolved solids, and nitrate concentrations than agricultural land-use networks. In order to assess the magnitude of statistically significant changes, the median of the differences between constituent concentrations from the first full-network sampling event and those from the second full-network sampling event was calculated using the Turnbull method. The largest median decadal increases in chloride concentrations were in networks in the Upper Illinois River Basin (67 mg/L) and in the New England Coastal Basins (34 mg/L), whereas the largest median decadal decrease in chloride concentrations was in the Upper Snake River Basin (1 mg/L). The largest median decadal increases in dissolved solids concentrations were in networks in the Rio Grande Valley (260 mg/L) and the Upper Illinois River Basin (160 mg/L). The largest median decadal decrease in dissolved solids concentrations was in the Apalachicola-Chattahoochee-Flint River Basin (6.0 mg/L). The largest median decadal increases in nitrate as nitrogen (N) concentrations were in networks in the South Platte River Basin (2.0 mg/L as N) and the San Joaquin-Tulare Basins (1.0 mg/L as N). The largest median decadal decrease in nitrate concentrations was in the Santee River Basin and Coastal Drainages (0.63 mg/L). The magnitude of change in networks with statistically significant increases typically was much larger than the magnitude of change in networks with statistically significant decreases. The magnitude of change was greatest for chloride in the urban land-use networks and greatest for dissolved solids and nitrate in the agricultural land-use networks. Analysis of data from all networks combined indicated statistically significant increases for chloride, dissolved solids, and nitrate. Although chloride, dissolved solids, and nitrate concentrations were typically less than the drinking-water standards and guidelines, a statistical test was used to determine whether or not the proportion of samples exceeding the drinking-water standard or guideline changed significantly between the first and second full-network sampling events. The proportion of samples exceeding the U.S. Environmental Protection Agency (USEPA) Secondary Maximum Contaminant Level for dissolved solids (500 milligrams per liter) increased significantly between the first and second full-network sampling events when evaluating all networks combined at the national level. Also, for all networks combined, the proportion of samples exceeding the USEPA Maximum Contaminant Level (MCL) of 10 mg/L as N for nitrate increased significantly. One network in the Delmarva Peninsula had a significant increase in the proportion of samples exceeding the MCL for nitrate. A subset of 261 wells was sampled every other year (biennially) to evaluate decadal-scale changes using a time-series analysis. The analysis of the biennial data set showed that changes were generally similar to the findings from the analysis of decadal-scale change that was based on a step-trend analysis. Because of the small number of wells in a network with biennial data (typically 4-5 wells), the time-series analysis is more useful for understanding water-quality responses to changes in site-specific conditions rather than as an indicator of the change for the entire network.

Scientific Investigations Report↗

USGS1976

Resource data bases-Resource assessment

The U.S. Geological Survey's Office of Resource Analysis is developing computer methods for the handling of mineral-resources data in order to provide improved means for addressing and manipulating data. These methods include: computerized data files and predictive resource models. Data files contain the raw or disaggregated information on mineral deposits and commodities. One operational data file is CRIB (Computerized Resources Information Bank) which is a general purpose inventory and reference file on metallic and nonmetallic mineral deposits. A computer file on resources should contain detailed information on the following main categories: record identification, name and location, description of deposit, analytical data, and production/reserves. A resource model employs postulates and inferences in conjunction with the data to make predictions about resources-as key variables concerning a mineral commodity are changed. The objective is to estimate the availability of minerals including: geological availability (occurrence models), technological availability (exploration and beneficiation models), and economic availability (economics models). ?? 1976.

Computers & Geosciences↗

USGS2016

Challenges for mapping cyanotoxin patterns from remote sensing of cyanobacteria

Using satellite imagery to quantify the spatial patterns of cyanobacterial toxins has several challenges. These challenges include the need for surrogate pigments – since cyanotoxins cannot be directly detected by remote sensing, the variability in the relationship between the pigments and cyanotoxins – especially microcystins (MC), and the lack of standardization of the various measurement methods. A dual-model strategy can provide an approach to address these challenges. One model uses either chlorophyll -a (Chl -a ) or phycocyanin (PC) collected in situ as a surrogate to estimate the MC concentration. The other uses a remote sensing algorithm to estimate the concentration of the surrogate pigment. Where blooms are mixtures of cyanobacteria and eukaryotic algae, PC should be the preferred surrogate to Chl -a . Where cyanobacteria dominate, Chl -a is a better surrogate than PC for remote sensing. Phycocyanin is less sensitive to detection by optical remote sensing, it is less frequently measured, PC laboratory methods are still not standardized, and PC has greater intracellular variability. Either pigment should not be presumed to have a fixed relationship with MC for any water body. The MC-pigment relationship can be valid over weeks, but have considerable intra- and inter-annual variability due to changes in the amount of MC produced relative to cyanobacterial biomass. To detect pigments by satellite, three classes of algorithms (analytic, semi-analytic, and derivative) have been used. Analytical and semi-analytical algorithms are more sensitive but less robust than derivatives because they depend on accurate atmospheric correction; as a result derivatives are more commonly used. Derivatives can estimate Chl -a concentration, and research suggests they can detect and possibly quantify PC. Derivative algorithms, however, need to be standardized in order to evaluate the reproducibility of parameterizations between lakes. A strategy for producing useful estimates of microcystins from cyanobacterial biomass is described, provided cyanotoxin variability is addressed.

Harmful Algae↗

USGS2012

Contaminants in stream sediments from seven U.S. metropolitan areas: Data summary of a National Pilot Study

This report presents data collected as a part of a synoptic survey of stream sediment contaminants, associated watershed characteristics and invertebrate responses in laboratory sediment toxicity tests from 98 streams (sites) in seven metropolitan study areas across the continental United States. The report presents methods, data, and sediment-quality guidelines, including the derivation of a new sediment pyrethroid probable effects concentration, for the purposes of relating measured contaminants to land use and toxicity evaluation. The study evaluated sites that ranged in their degree of relative urbanization within the study areas of Atlanta, Boston, Dallas-Fort Worth, Denver, Milwaukee-Green Bay, Salt Lake City, and Seattle-Tacoma. In all, 108 chemical analytes quantified in the study are presented, by class and number of individual compounds, as follows: polyaromatic hydrocarbons (PAHs) (28), organochlorine pesticides (OCs) (18), polychlorinated biphenyls (Aroclors) (3), pyrethroid insecticides (14), fipronil compounds (4), priority trace and other major elements (41). The potential of these sediments to cause toxicity to sediment-dwelling invertebrates was evaluated using two standard sediment toxicity tests: a 28-day growth and survival toxicity test with the amphipod Hyalella azteca, and a 10-day growth and survival toxicity test with the midge Chironomus dilutus. Further, approximately 95 relevant watershed and reach-level characteristics were generated and are presented to aid in interpretation and explanation of contaminant and toxicity patterns. Interpretation of the findings of this study, including the relationships with urbanization and other factors, the relationship between sediment toxicity and sediment chemistry in the seven study areas, and the sources and occurrence of pyrethroid insecticides, are discussed in detail in a forthcoming series of journal articles.

Boston;Atlanta;Milwaukee;Green Bay;Dallas;Fort Wor↗