Search USGS⌕ Search

SEARCH · Search USGS

Results for “Mississippi Geology”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55Linked to original sources
USGS2015

Evaluation of Xylem EXO water-quality sondes and sensors

Two models of multiparameter sondes manufactured by Xylem, parent company of Yellow Springs Incorporated (YSI)—EXO1 and EXO2—equipped with EXO conductivity/temperature (C/T), pH, dissolved oxygen (DO), and turbidity sensors, were evaluated by the U.S. Geological Survey (USGS) Hydrologic Instrumentation Facility. The sondes and sensors were evaluated in two phases for compliance with the manufacturer’s specifications and the USGS acceptance criteria for continuous water-quality monitors. Phase one tested the accuracy of the water-quality sondes equipped: (a) with a C/T, pH, DO, and turbidity sensor by comparing the EXO sensors’ measured values to those of an equivalently configured YSI 6920 V2-2 sensor, and (b) with multiple sensors of the same parameter type (such as three pH sensors and a C/T sensor) on a single sonde at room temperature and at an extended temperature range. In addition to accuracy, the communication protocols and the manufacturing specifications for range of detection and operating temperature were also tested during this phase. Phase two evaluated the sondes’ performance in a surface-water environment by deploying an EXO1 and an EXO2 equipped with pH, C/T, DO, and turbidity sensors at USGS site 02492620 located at East Pearl River near Bay Saint Louis, Mississippi. The EXO sondes’ temperature deviations from a certified YSI 4600 digital thermometer were within the ±0.2 degree Celsius (°C) USGS criteria, but were greater than the ±0.01 °C manufacturing specification. The conductivity sensors met the ±3 percent USGS criteria for specific conductance greater than 100 microsiemens per centimeter. The sensors met the more stringent ±0.5 percent manufacturing specification only at room temperature in the 250 microsiemens per centimeter (µS/cm) standard. The manufacturing and USGS criteria (±0.2 pH unit) were met in pH standards 4, 9.2, 10, and 12.45, but were not met in pH 1.68 standard. The DO sensors met both the ±0.3 milligram per liter (mg/L) USGS criteria and the ±1 percent manufacturing specification. The ±5 percent USGS criteria for turbidity in waters not exceeding 2,000 formazin nephelometric units (FNU) were met by the five turbidity sensors tested; however, all five sensors failed to meet these requirements at turbidities exceeding 2,000 FNU. The more stringent ±2 percent manufacturing turbidity specification for water with less than 1,000 FNU was met by only one of the five sensors tested. The results from the field deployment indicated acceptable agreement in temperature, specific conductance, pH, and DO between the EXO sondes, the site sonde, and the reference sonde. The EXO1 and EXO2 turbidity measurements differed from the site sonde by approximately 23 and 25 percent, respectively.

Open-File Report↗
USGS1975

Water resources of the Cedar River watershed, southeastern Minnesota

The Cedar River Watershed Unit (as established by the states of Minnesota) consists of 1,204 square miles (3,118 square kilometres) of flat or gently undulating plain. The watershed is drained by the Cedar River and several smaller streams that flow south into Iowa and eventually into the Mississippi River. Its easternmost neck is part of a broad, flat, well-drained plain, covered by a thin sheet of glacial drift. Sinkholes have formed in the near surface carbonate bedrock, and a karst topography is developing. Farther north, along the east boundary, the drift is more than 200 feet (61 m) thick, and the land surface reaches altitudes of more than 1,450 feet (442 m) – the highest area in southeastern Minnesota. In the central part of the watershed in the southern flood plain of the Cedar River, the drift is less than 100 feet (30 m) thick, and the land surface altitude is less than 1,140 feet (347 m). The western part is dominated by a terminal moraine of the last Wisconsin glacier. Here the drift is more than 300 feet (91 m) thick, is poorly drained, and has numerous lakes. The watershed is mostly prairie and is well suited for farming, which is the dominant economic activity. Topographic quadrangle maps published by the U.S. Geological Survey are available for the entire watershed.

Minnesota↗
USGS2000

Velocity and stage data collected in a laboratory flume for water-surface slope determination using a pipe manometer

U.S. Geological Survey (USGS) hydrologists and ecologist are conducting studies to quantify vegetative flow resistance in order to improve numerical models of surface-water flow in the Florida Everglades. Water-surface slope is perhaps the most difficult of the flow resistance parameters to measure in the Everglades due to the very low gradients of the topography and flow. In an effort to measure these very small slopes, a unique pipe manometer was developed for the local measurement of water-surface slopes on the order of 1 centimeter per kilometer (cm/km). According to theory, a very precise measurement of centerline velocity obtained inside the pipe manometer should serve as a unique proxy for water-surface slope in the direction of the pipe axis. In order to confirm this theoretical relationship and calibrate the pipe manometer, water-surface elevation and pipe centerline velocity data were simultaneously measured in a set of experiments carried out in the tilting flume at the USGS Hydraulic Laboratory Facility at Stennis Space Center, Mississippi. A description of the instrumentation and methods used to evaluate this technique for measuring water-surface slope as well as a summary of the entire data set is presented.

Open-File Report↗
USGS2012

A catalog of Louisiana's nesting seabird colonies

Summarizing his colonial nesting waterbird survey experiences along the northern coast of the Gulf of Mexico in a paper presented to the Colonial Waterbird Group of the Waterbird Society (Portnoy 1978), bird biologist John W. Portnoy stated, “This huge concentration of nesting waterbirds, restricted almost entirely to the wetlands and estuaries of southern Louisiana, is unmatched in all of North America; for example, a 1975 inventory of wading birds along the Atlantic Coast from Maine to Florida [Custer and Osborn, in press], tallied 250,000 breeding [waterbirds] of 14 species, in contrast with the 650,000 birds of 15 species just from Sabine Pass to Mobile Bay.” The “650,000 birds” to which Portnoy referred, were tallied by him in a 1976 survey of coastal Louisiana, Mississippi, and Alabama (see below, under “Major Surveys” section). According to the National Atlas of Coastal Waterbird Colonies in the Contiguous United States: 1976-82 (Spendelow and Patton 1988), the percentages of the total U.S. populations of Laughing Gull (11%), Forster's Tern (52%), Royal Tern (16%), Sandwich Tern (77%), and Black Skimmer (44%) which annually nest in Louisiana are significant – perhaps crucially so in the cases of Forster's Tern, Sandwich Tern, and Black Skimmer. Nearly three decades after Spendelow and Patton's determinations above, coastal Louisiana still stands out as the major center of colonial wading bird and seabird nesting in all of the United States. Within those three intervening decades, however, the collective habitats which comprise Louisiana's now fragile coastal zone have taken major hits from commercial/residential, oil & gas, and other industrial development, primarily in the form of coastal erosion exacerbated by these and other factors (Portnoy 1978, Spendelow and Patton 1988, Martin and Lester 1990, Green, et al. 2006). Moreover, during this same period, both geologic subsidence rates (Tornqvist et al. 2008) and mean sea-level (Tornqvist et al. 2002) have increased, along with significant tropical storm activity; all of which have combined to impact available marsh, barrier island, beach, and dredge spoil nesting habitat for waterbirds, especially seabirds, throughout the coastal zone of Louisiana. The primary objective of this publication is to detail those coastal Louisiana colonial seabird nesting sites for which we have reasonably accurate data, in a tabular, site-by-site format. All major survey (1976-2008) data of site-by-site seabird species counts, as well as several smaller data sets, referred to in the site history tables as “miscellaneous observations” obtained during the May-June seabird breeding period, are included. It is our hope that these data will provide a dependable foundation from which future colonial seabird nesting surveys might be planned and carried out, as well as showcase the importance of coastal Louisiana's seabird rookeries, and contribute to their conservation.

Louisiana↗
USGS1997

Element distribution patterns in the ordovician Galena group, Southeastern Minnesota: Indicators of fluid flow and provenance of terrigenous material

As part of a regional geochemical investigation of lower Paleozoic strata in the Hollandale embayment of southeastern Minnesota, elemental concentrations in acid-insoluble residues were determined for carbonate rock in the Middle Ordovician Galena Group. Elemental distribution patterns within the insoluble residues, particularly those of Ti, Al, and Zr, show that the Wisconsin dome and the Wisconsin arch, which contributed sediment to the embayment prior to Galena time, continued as weak sources of sediment during this period. In contrast, trace metals commonly associated with Mississippi Valley-type lead-zinc mineralization, including Pb, Zn, Cu, Ag, Ni, Co, As, and Mo, show dispersal patterns that are independent of those associated with primary depositional phenomena. These trace metals are concentrated in southern Minnesota in carbonate rocks near the interface between limestone- and dolostone-dominated strata. Dispersal patterns imply that the metals were carried by a north-flowing regional ground-water system. The results show that the geochemical attributes of insoluble residues can be used to distinguish provenance and transport directions of primary sediments within a depositional basin from effects of subsequent regional ground-water flow systems.

Economic Geology↗
USGS2017

Fluorine

Fluorine compounds are essential in numerous chemical and manufacturing processes. Fluorspar is the commercial name for fluorite (isometric CaF 2 ), which is the only fluorine mineral that is mined on a large scale. Fluorspar is used directly as a fluxing material and as an additive in different manufacturing processes. It is the source of fluorine in the production of hydrogen fluoride or hydrofluoric acid, which is used as the feedstock for numerous organic and inorganic chemical compounds. The United States was the world’s leading producer of fluorspar until the mid-1950s. In the mid-1970s, the U.S. fluorspar mining industry began to decline because of foreign competition. By 1982, there was essentially only a single U.S. producer left, and that company ceased mining in 1996. Consumption of fluorspar in the United States peaked in the early 1970s, which was also the peak period of U.S. steel production. Since then, U.S. fluorspar consumption has decreased substantially; the United States has nonetheless increased its imports of downstream fluorine compounds, such as, in order of tonnage imported, hydrofluoric acid, aluminum fluoride, and cryolite. This combination of no U.S. production (until recently) and high levels of consumption has made the United States the world’s leading fluorspar-importing country, in all its various forms. The number of fluorspar-exporting countries has decreased substantially in recent decades, and, as a result, the United States has become dependent on just a few countries to supply its needs. In 2013, the United States imported the majority of its fluorspar from three countries, which were, in descending order of the amount imported, Mexico, China, and South Africa. Geologically, in igneous systems, fluorine is one of a number of elements that are “incompatible.” These incompatible elements become concentrated in the residual magma while the common silicates crystallize upon magma ascent and cooling, leading to relatively high fluorine concentrations in the more evolved or differentiated igneous rocks and in hydrothermal deposits associated with those evolved igneous rocks. In sedimentary rocks, fluorine’s highest concentrations are found in phosphorites because fluorine substitutes for hydroxyl ions in apatite, which leads to fluorine concentrations of, typically, from 2 to 4 weight percent in phosphorites. Because of the presence of fluorine, phosphate fertilizer manufacturers can produce a fluorosilicic acid byproduct. Most deposits mined for fluorine are hydrothermal, however, and consist of fluorine minerals that precipitated from hot water. Magmatic brines and brines from deep within sedimentary basins that have high concentrations of dissolved fluoride are the mineralizing fluids for various types of hydrothermal fluorspar deposits. Relatively dilute hydrothermal fluids that formed in some volcanic rocks can also transport sufficient fluoride to form a high-grade fluorspar deposit. Fluorite has low solubility in a common range of hydrothermal temperatures, particularly from about 160 degrees Celsius (°C) down to 60 °C. The increasing fluorite solubility below 60 °C partly explains why some water with exceptionally high levels of dissolved fluorine are found even at ambient temperatures in evaporitic lake basins in some East African Rift valleys in Kenya and Tanzania. The geologic conditions that led to the high concentrations there are known to exist in a number of other places in the world as well, including, perhaps, places in the Basin and Range province of the United States. Eight minerals or mineral groups have sufficient fluorine in their structures to be considered as possible ores of the element; they are bastnaesite (also spelled bastnäsite; and other fluorocarbonates), cryolite, sellaite, villiaumite, fluorite, fluorapatite (in phosphorites), various phyllosilicates, and topaz. Fluorite is currently the only mineral that is mined for fluorine, and nomineral except fluorite is likely to become a source of commercially produced fluorine as a primary product as long as supplies from relatively thick and high-grade fluorite deposits continue to be available. At least seven classes (which include one subclass) of hydrothermal fluorite deposits are recognized; they are classified according to their tectonic and (or) magmatic settings, as follows: (1) carbonatite-related fluorspar deposits; (2) alkaline-intrusion-related fluorspar deposits; (3) alkaline-volcanic-related epithermal fluorspar deposits; (4) Mississippi Valley-type fluorspar deposits (and a subclass of salt-related carbonate-hosted fluorspar deposits); (5) fluorspar deposits related to strongly differentiated granites; (6) subalkaline-volcanic-related epithermal fluospar deposits; and (7) fluorspar deposits that appear to be conformable within tuffaceous limy lacustrine sediments. An eighth class (not hydrothermal) is that of fluorspar deposits concentrated in soils and weathered zones; that is, residual fluorspar deposits. Generally, fluorspar deposits related to strongly differentiated granites have larger tonnages and lower grades than carbonatite-related fluorspar deposits, which, in turn, have larger tonnages and lower grades than fluorspar vein deposits from various other classes. The United States has a few identified resources of fluorspar, most notably the Klondike II property in the Illinois- Kentucky fluorspar district located about 8 kilometers southwest of Salem, Kentucky, which has a large vein that contains at least 1.6 million metric tons at a grade of 60 percent CaF 2 (Feytis, 2009). Additional fluorspar resources of lower grade but larger tonnage have been identified at Hicks Dome in the Illinois-Kentucky fluorspar district and at Lost River near the western tip of the Seward Peninsula in Alaska, along with a couple of dozen smaller, higher grade resources. Internationally, new mines that either opened before the beginning of 2013 or were scheduled to open soon after that time include the Nui Phao tungsten-fluorspar-bismuth-copper-gold deposit in northern Vietnam; the St. Lawrence project in Newfoundland, Canada, which is located in a well-known fluorspar district; the Bamianshan deposit, which is related to a strongly differentiated granite in northwestern Zhejiang Province, China, near some of that Province’s large, subalkaline-volcanic-related epithermal veins; and the Nokeng project in South Africa, which is also related to a strongly differentiated granite. Other deposits in northwestern Australia, Nevada (United States), Norway, South Africa, and Sweden have been identified and could be put into production within just a few years. Among undiscovered resources, an interesting possibility might be to produce a fluorine product from evaporitic, high-fluorine, high-pH sodium-carbonate brines like Lake Magadi (Kenya) and Lake Natron (Tanzania) in Africa’s Eastern Rift Valley. In addition, apparently conformable fluorspar deposits in tuffaceous limy lacustrine sediments, such as those in Italy, are likely to occur in similar young alkalic volcanic settings elsewhere in the world. Modern geophysical and geochemical exploration techniques have typically not been brought to bear in exploration for new fluorspar deposits, although such techniques are likely to be used in future exploration. The tendency for fluorine to dissolve in significant concentrations in water at low temperature allows both surface water and groundwater to be used as sampling media in geochemical exploration. Evolved granite-related fluorspar deposits may be particularly susceptible to geophysical exploration methods because crystalline rocks that form a basement to sedimentary sections can be approximately defined with gravity and magnetic methods, and magnetite-bearing skarns can be directly detected with magnetic surveys. Environmental considerations of fluorine mining focus especially on drinking water, where high fluorine concentrations can lead to tooth decay; dental and skeletal fluorosis; and bone and cartilage conditions, including genu valgum, which is the crippling bone deformity more commonly known as knock knee. Trace amounts of other elements in fluorspar ores are a concern at some deposits; for example, high beryllium concentrations in alkaline-volcanic-related epithermal deposits or high cadmium concentrations associated with Mississippi Valley-type and salt-related carbonate-hosted fluorspar deposits. Future research might include testing whether fluorine can be extracted economically from high-pH, sodium-carbonate brines and exploring for new occurrences of apparently conformable fluorspar deposits in tuffaceous limy lacustrine sediments outside of the Latium Region of Italy. Other promising new areas of research could be studies of fluorspar deposit fluid inclusion compositions by quadrupole mass spectrometry, by noble gas mass spectrometry on irradiated fluid inclusions, or by chlorine isotopes, while also measuring the chemistry of the same fluid inclusions either by bulk crush-and-leach methods or by laser ablation-inductively coupled plasma mass spectrometry. Advanced studies of fluid inclusion chemistry could be applied beneficially to some of the enigmatic large epithermal fluorspar veins at various places in the world, where they might determine those deposits’ possible relationships to igneous intrusions, or to dissolved salt, or to heated meteoric water in volcanic sections, or perhaps to all three. This knowledge could help focus new exploration.

Professional Paper↗
USGS2014

Characterization of the structure, clean-sand percentage, dissolved-solids concentrations, and estimated quantity of groundwater in the Upper Cretaceous Nacatoch Sand and Tokio Formation, Arkansas

The West Gulf Coastal Plain, Mississippi embayment, and underlying Cretaceous aquifers are rich in water resources; however, large parts of the aquifers are largely unusable because of large concentrations of dissolved solids. Cretaceous aquifers are known to have large concentrations of salinity in some parts of Arkansas. The Nacatoch Sand and the Tokio Formation of Upper Cretaceous age were chosen for investigation because these aquifers produce groundwater to wells near their outcrops and have large salinity concentrations away from their outcrop areas. Previous investigations have indicated that dissolved-solids concentrations of groundwater within the Nacatoch Sand, 2–20 miles downdip from the outcrop, render the groundwater as unusable for purposes requiring freshwater. Groundwater within the Tokio Formation also exhibits large concentrations of dissolved solids downdip. Water-quality data showing elevated dissolved-solids concentrations are limited for these Cretaceous aquifers because other shallower aquifers are used for water supply. Although not suitable for many uses, large, unused amounts of saline groundwater are present in these aquifers. Historical borehole geophysical logs were used to determine the geologic and hydrogeologic properties of these Cretaceous aquifers, as well as the quality of the groundwater within the aquifers. Based on the interpretation of borehole geophysical logs, in Arkansas, the altitude of the top of the Nacatoch Sand ranges from more than 200 to less than -4,000 feet; the structural high occurs in the outcrop area and the structural low occurs in southeastern Arkansas near the Desha Basin structural feature. The thickness of the Nacatoch Sand ranges from 0 to over 550 feet. The minimum thickness occurs where the formation pinches out in the outcrop area, and the maximum thickness occurs in the southwestern corner of Arkansas. Other areas of large thickness include the area of the Desha Basin structural feature in southeastern Arkansas and in an area on the border of Cross and St. Francis Counties in eastern Arkansas. The clean-sand percentage of the total Nacatoch Sand thickness ranges from less than 20 percent to more than 60 percent and generally decreases downdip. The Nacatoch Sand contains more than 120.5 million acre-feet of water with a dissolved-solids concentration between 1,000 and 10,000 milligrams per liter (mg/L), more than 57.5 million acre-feet of water with a dissolved-solids concentration between 10,000 and 35,000 mg/L, and more than 122.5 million acre-feet of water with a dissolved-solids concentration more than 35,000 mg/L. The altitude of the top of the Tokio Formation, in Arkansas, ranges from more than 200 feet to less than -4,400 feet; the structural high occurs in the outcrop area and the structural low occurs in southeastern Arkansas near the Desha Basin structural feature. The thickness of the Tokio Formation, in Arkansas, ranges from 0 to over 400 feet. The minimum thickness occurs where the formation pinches out in the outcrop area, and the maximum thickness occurs in the southwestern corner of Arkansas. The clean-sand percentage of the total Tokio Formation thickness ranges from less than 20 percent to more than 60 percent and generally decreases away from the outcrop area. The Tokio Formation contains more than 2.5 million acre-feet of water with a dissolved-solids concentration between 1,000 and 10,000 mg/L, more than 12.5 million acre-feet of water with a dissolved-solids concentration between 10,000 and 35,000 mg/L, and nearly 43.5 million acre-feet of water with a dissolved-solids concentration more than 35,000 mg/L.

Arkansas↗
USGS2025

Statistical approaches for modeling correlated grade and tonnage distributions and applications for mineral resource assessments

Correlations between grade and tonnage exist in mineral resource data compiled from published reports, but they are not always addressed during quantitative assessment of undiscovered mineral resources. Failure to account for correlated grade and tonnage distributions can result in geologically unrealistic assessment results. Current software tools simulate univariate ore tonnage and multivariate resource grades of undiscovered deposits independently. As a result, analysts are forced to rely on ad-hoc solutions to minimize the correlation issues by: 1) creating subsets of data with restricted criteria; 2) truncating grade and tonnage distributions; and 3) testing model robustness using exploratory data analysis. While these methods represent pragmatic solutions, the statistical solutions presented here provide additional options to address real correlations in grade and tonnage data used for mineral resource assessments. We present a modified version of the MapMark4 package in R that introduces two alternatives for modeling grade and tonnage distributions, consisting of a multivariate solution that accounts for correlations between ore tonnage and metal grades and an empirical solution that utilizes simple random sampling with replacement to reproduce coupled grades and tonnages from the input data. We present simulations for contained ore and metal for three case studies representing tungsten skarn, komatiite-hosted nickel, and sediment-hosted carbonate amagmatic zinc-lead (Mississippi Valley-type) deposits. Employing the methods presented here yields quantitative mineral resource assessment results that more closely reflect the empirical distributions of grades and tonnages observed in nature and expands the applicability of these tools for ongoing critical mineral resource assessments.

Applied Computing and Geosciences↗
USGS2008

Estimated Withdrawals from Stream-Valley Aquifers and Refined Estimated Withdrawals from Selected Aquifers in the United States, 2000

The U.S. Geological Survey National Water Use Information Program compiles estimates of fresh ground-water withdrawals in the United States on a 5-year interval. In the year-2000 compilation, withdrawals were reported from principal aquifers and aquifer systems including two general aquifers - Alluvial and Other aquifers. Withdrawals from a widespread aquifer group - stream-valley aquifers - were not specifically identified in the year-2000 compilation, but they are important sources of ground water. Stream-valley aquifers are alluvial aquifers located in the valley of major streams and rivers. Stream-valley aquifers are long but narrow aquifers that are in direct hydraulic connection with associated streams and limited in extent compared to most principal aquifers. Based in large part on information published in U.S. Geological Survey reports, preliminary analysis of withdrawal data and hydrogeologic and surface-water information indicated areas in the United States where possible stream-valley aquifers were located. Further assessment focused on 24 states and the Commonwealth of Puerto Rico. Withdrawals reported from Alluvial aquifers in 16 states and withdrawals reported from Other aquifers in 6 states and the Commonwealth of Puerto Rico were investigated. Two additional States - Arkansas and New Jersey - were investigated because withdrawals reported from other principal aquifers in these two States may be from stream-valley aquifers. Withdrawals from stream-valley aquifers were identified in 20 States and were about 1,560 Mgal/d (million gallons per day), a rate comparable to withdrawals from the 10 most productive principal aquifers in the United States. Of the 1,560 Mgal/d of withdrawals attributed to stream-valley aquifers, 1,240 Mgal/d were disaggregated from Alluvial aquifers, 150 Mgal/d from glacial sand and gravel aquifers, 116 Mgal/d from Other aquifers, 28.1 Mgal/d from Pennsylvanian aquifers, and 24.9 Mgal/d from the Mississippi River Valley alluvial aquifer. Five States, including Colorado (552 Mgal/d), Kansas (384 Mgal/d), Oklahoma (126 Mgal/d), Kentucky (102 Mgal/d), and Ohio (100 Mgal/d), accounted for 81 percent of estimated stream-valley aquifer withdrawals identified in this report. Of the total withdrawals from stream-valley aquifers, about 63 percent (984 Mgal/d) were used for irrigation, 26 percent (400 Mgal/d) for public-supply, and 11 percent (177 Mgal/d) for self-supplied industrial uses. The largest estimated water withdrawals were from stream-valley aquifers associated with the South Platte (404 Mgal/d), Arkansas (395 Mgal/d), and Ohio (221 Mgal/d) Rivers.

Scientific Investigations Report↗
USGS1989

The geomorphology of the Mississippi River chenier plain

The chenier plain of the Mississippi River is a shore-parallel zone of alternating transgressive clastic ridges separated by progradational mudflats. The term chenier is derived from the cajun term chene for oak, the tree species that colonizes the crests of the higher ridges. The Mississippi River chenier plain stretches 200 km from Sabine Pass, Texas, to Southwest Point, Louisiana and ranges between 20 and 30 km wide, with elevations of 2–6 m. The timing and the process of formation could be re-evaluated in the light of new chronostratigraphic findings in the Mississippi River delta plain. The stratigraphic relationship between the Teche and Lafourche delta complexes and Ship Shoal offshore indicates that these delta complexes belong to different delta plains that developed at different sealevels. It appears that the Teche delta complex is associated with the late Holocene delta plain which developed 7000 to 3000 yrs B.P. when sealevel stood 5–6 m lower than present. A regional transgression occurred between approximately 3000 BP and 2500 yrs B.P., leading to the transgressive submergence of the late Holocene delta plain, producing the regional Teche shoreline. The timing of this transgression conforms to the age of the most landward ridge in the chenier plain, the Little Chenier-Little Pecan Island trend, which dates at about 2500 yrs B.P. This ridge trend was originally interpreted as representing the Teche delta complex switching event with the landward Holocene/Pleistocene contact representing the high stand shoreline. The implication of this new interpretation is that the Little Chenier-Little Pecan Island trend represents the high stand shoreline, a continuation of the Teche shoreline separating the late Holocene and Recent delta plains, and that the Holocene/Pleistocene contact represents the leading edge of the marshes transgressing onto the Prairie Terrace. Significant mudflat progradation seems to require a westerly position of the Mississippi River, but the numerous different forms and ages of cheniers do not correspond well to the timing of major delta complex switching. Progradation of the chenier plain appears to be associated with building of the Recent delta plain and not the Teche complex of the late Holocene delta plain. The occurrence of individual ridges appears to be primarily tied to delta lobe switching within the Lafourche complex and variations in sediment supply from local rivers. The recent development of the Atchafalaya delta complex to the west is the closest position of an active distributary to the chenier plain since sealevel stabilization; a new episode of rapid mudflat progradation is thus taking place.

Marine Geology↗
USGS2006

Status of Water Levels and Selected Water-Quality Conditions in the Mississippi River Valley Alluvial Aquifer in Eastern Arkansas, 2004

During the spring of 2004, water levels were measured in 684 wells completed in the Mississippi River Valley alluvial aquifer in eastern Arkansas. Ground-water levels are affected by intense ground-water withdrawals resulting in extensive potentiometric depressions. In 2004, the highest water-level altitude measured was 293 feet above National Geodetic Vertical Datum of 1929 in northeastern Clay County. The lowest water-level altitude measured was 76 feet above National Geodetic Vertical Datum of 1929 in the center of Arkansas County. A large depression in the potentiometric surface was located in Arkansas, Lonoke, and Prairie Counties during 1998 and persisted to 2002. The area enclosed in the 100-foot contour in Arkansas County in 2004 is about the same as in 2002, however, the area enclosed in the 100-foot contour in Lonoke and Prairie Counties in 2004 has receded. Two shallower cones of depressions were located in Craighead, Cross, and Poinsett Counties and St. Francis, Woodruff, Lee, and Monroe Counties west of Crowleys Ridge during 1998. The 2004 potentiometricsurface map shows that the areas enclosed by the 140-foot contour have continued to expand. A map of changes in water-level measurements between 2000 and 2004 was constructed using the difference between water-level measurements from 625 wells reported in this report and the 2000 Mississippi River Valley alluvial aquifer report. Water-level changes between 2000 and 2004 ranged from -31.1 feet to 16.3 feet, with a mean of -0.7 feet (negative changes indicating water-level declines, positive changes indicating water-level rises). The largest rise of 16.3 feet is in Arkansas County and the largest decline of -31.1 feet is in Prairie County. Long-term water-level changes were calculated for 134 wells in the alluvial aquifer for the period from 1980 to 2004. The mean annual decline in water level for the entire study area was -0.31 feet per year with a range of -1.35 feet per year to 0.84 feet per year. The analysis of long-term water-level changes (1980-2004) in the depression in Arkansas and Prairie Counties shows the effects of the elongation of this depression. Water samples were collected from 138 wells completed in the alluvial aquifer and measured onsite for specific conductance and temperature. Samples were collected at 71 wells for dissolved chloride analysis at the U.S. Geological Survey National Water Quality Laboratory. Specific conductance ranged from 205 microsiemens per centimeter at 25 degrees Celsius at a well in Lonoke County to 1,440 microsiemens per centimeter at 25 degrees Celsius at a well in Monroe County.

Scientific Investigations Report↗
USGS2011

Monitoring a large volume CO2 injection: Year two results from SECARB project at Denbury’s Cranfield, Mississippi, USA

The Southeast Regional Carbon Sequestration Partnership (SECARB) early project in western Mississippi has been testing monitoring tools and approaches to document storage efficiency and storage permanence under conditions of CO 2 EOR as well as downdip injection into brine. Denbury Onshore LLC is host for the study and has brought a depleted oil and gas reservoir, Cranfield Field, under CO 2 flood. Injection was started in July 2008 and has now achieved injection rates greater than 1.2 million tons/year though 23 wells, with cumulative mass injected as of August, 2010 of 2.2 million metric tons. Injection is into coarse grained fluvial deposits of the Cretaceous lower Tuscaloosa Formation in a gentle anticline at depths of 3300 m. A team of researchers from 10 institutions has collected data from five study areas, each with a different goal and different spatial and temporal scale. The Phase 2 study began at the start of injection and has been using pressure and temperature as a tool for assessing permanence mostly in the oil productive interval. Real-time read-out shows high sensitivity to distant changes in injection rate and confirms the geologic model of reservoir compartmentalization. Above-zone pressure monitoring ∼120 m above the injection interval is used to test the sensitivity of this approach for documentation of integrity of the confining system in an area of numerous well completions as pressure increase is induced in the reservoir by more than 70 bar. Monitoring of the High Volume Injection Test (HiVIT) area includes repeat measurements of aqueous geochemistry in the injection zone. Rock-water- CO 2 interactions in the reservoir as CO 2 dissolves are minimized by mineral “armoring” by abundant chlorite cement in high permeability reservoir sandstone. Geochemical monitoring of confined freshwater aquifers at depths of 70–100 m is underway. Groundwater analysis focuses on assessment of the sensitivity of this method to detect leakage above background variability. A repeat seismic survey of the HiVIT is planned for late 2010 to assess saturation change especially in downdip brine-only areas. A study focused on feasibility of monitoring the shallow subsurface to separate leakage from normal complex surface fluxes is underway at an monitoring array installed in October 2009 to assess the interactions of recharge, soil gas, and shallow groundwater aquifers. Recent well re-entry and tracer injection will provide further information to interpret observed elevated deep-sourced methane. The Detailed Area Study (DAS) is collecting dense time-lapse data from closely-spaced three well array of an injector and two observation wells. The observation wells were completed with fiberglass casing to facilitate electrical resistance tomography (ERT) measurements, and a diverse array of instrumentation was both cemented behind casing and suspended on tubing. Injection started at the DAS December 1, 2009. We have measured pulsed neutron and resistivity via wireline, downhole and above-zone pressure, distributed temperature, and fluid chemistry including introduced pulses of perfluorocarbons, noble gases, and SF6 as tracers. Between wells, time-lapse crosswell seismic and electrical resistance tomography (ERT) are used to measure saturation change. The goals are to measure changes as fluids evolve from single phase (brine) to two phase (CO 2 –brine) in order to document linkages between pressure and sweep efficiency. A time-lapse VSP survey bridges the vertical resolution and areal coverage between cross-well and surface seismic. The repeat surveys for many tools are scheduled for September, 2010. Reservoir characterization based on cores, historic and new wireline log data, production history, hydrologic tests, fluid analysis, and a three-D seismic survey have been used in multiple numerical models to predict reservoir response in order to design effective monitoring strategies and optimize deployment. History matching of observed response to predicted response is used to interpret results and improve confidence in conceptual models and numerical approaches. Probabilistic methods have been used to assess the significant uncertainties resulting from reservoir heterogeneity.

Mississippi↗
USGS2017

Evaluation of the Hydrolab HL4 water-quality sonde and sensors

The U.S. Geological Survey (USGS) Hydrologic Instrumentation Facility evaluated three Hydrolab HL4 multiparameter water-quality sondes by OTT Hydromet. The sondes were equipped with temperature, conductivity, pH, dissolved oxygen (DO), and turbidity sensors. The sensors were evaluated for compliance with the USGS National Field Manual for the Collection of Water-Quality Data (NFM) criteria for continuous water-quality monitors and to verify the validity of the manufacturer’s technical specifications. The conductivity sensors were evaluated for the accuracy of the specific conductance (SC) values (conductance at 25 degrees Celsius [ o C]), that were calculated by using the vendor default method, Hydrolab Fresh. The HL4’s communication protocols and operating temperature range along with accuracy of the water-quality sensors were tested in a controlled laboratory setting May 1–19, 2016. To evaluate the sonde’s performance in a surface-water field application, an HL4 equipped with temperature, conductivity, pH, DO, and turbidity sensors was deployed June 20–July 22, 2016, at USGS water-monitoring site 02492620, Pearl River at National Space Technology Laboratories (NSTL) Station, Mississippi, located near Bay Saint Louis, Mississippi, and compared to the adjacent well-maintained EXO2 site sonde. The three HL4 sondes met the USGS temperature testing criteria and the manufacturer’s technical specifications for temperature based upon the median room temperature difference between the measured and standard temperatures, but two of the three sondes exceeded the allowable difference criteria at the temperature extremes of approximately 5 and 40 ºC. Two sondes met the USGS criteria for SC. One of the sondes failed the criteria for SC when evaluated in a 100,000-microsiemens-per-centimeter (μS/cm) standard at room temperature, and also failed in a 10,000-μS/cm standard at 5, 15, and 40 ºC. All three sondes met the USGS criteria for pH and DO at room temperature, but one sonde exceeded the allowable difference criteria when tested in pH 5.00 buffer and at 40 ºC. The USGS criteria and the technical specifications for turbidity were met by one sonde in standards ranging from 10 to 3,000 nephelometric turbidity units (NTU). A second sonde met the USGS criteria and the technical specifications except in the 3,000-NTU standard, and the third sonde exceeded the USGS calibration criteria in the 10- and 20-NTU standards and the technical specifications in the 20-NTU standard. Results of the field test showed acceptable performance and revealed that differences in data sample processing between sonde manufacturers may result in variances between the reported measurements when comparing one sonde to another. These variances in data would be more pronounced in dynamic site conditions. The lack of a wiper or other sensor-cleaning device on the DO sensor could prove problematic, and could limit the use of the HL4 to profiling applications or at sites with limited biofouling.

Open-File Report↗
USGS1988

Stable isotope geochemistry of sphalerite and other mineral matter in coal beds of the Illinois and Forest City basins

Cleat and clastic dikes of Middle Pennsylvanian-age coal beds of the Illinois and Forest City basins of Illinois, Iowa, Missouri, and Kansas locally contain appreciable amounts of sphalerite within a kaolinite-pyrite-sphalerite (+ or - pyrite)-calcite paragenetic sequence. The sphalerite and associated minerals are of interest as a partial record of the history of fluids in the sedimentary basin and as possible indicators of Mississippi Valley-type mineralization. Moreover, zinc from the sphalerite may represent an exploitable by-product of coal mining and combustion.Pyrite is abundant in these coals both as fine-grained disseminated framboids that formed during early diagenesis and as coarser grained cleat fillings, etc., that formed much later. The delta 34 S values of this later pyrite, the sphalerite, and the coal organic matter range from -12 to 19 per mil. Within individual samples, however, pyrite, sphalerite, and organic matter sulfur delta 34 S values are nearly identical. This similarity strongly suggests related origins. The delta 34 S values of pyrite, sphalerite, and organic matter from coals of the Illinois basin and the central and southern Forest City basin range from -12 to 0 per mil. This range is not unique to the sphalerite-bearing coals; pyrite and organic matter from sphalerite-free high sulfur coals have similar delta 34 S values (Price and Shieh, 1979). We believe that sulfur produced by the breakdown of organosulfur compounds in the coal is incorporated into the epigenetic sulfides. In the northern Forest City basin, however, many samples have delta 34 S values between 8 and 19 per mil. These are similar to the delta 34 S values of sphalerite and pyrite from the Upper Mississippi Valley Zn-Pb district which lies northeast of the Forest City basin and north of the Illinois basin. This similarity suggests input from a Mississippi Valley-type hydrothermal system.Cleat kaolinite has delta D values of -36 to -24 per mil and delta 18 O values of 19.2 to 20.2 per mil. Assuming that clearing postdated the lignite rank of coalification implies that kaolinite was deposited between 40 degrees and 100 degrees C. At the lower temperatures, the kaolinite fluid would have had an isotopic composition similar to seawater; at the higher temperatures, it would have had a composition similar to the sphalerite-depositing fluid. Sphalerite was deposited from a fluid that was chemically and isotopically similar to the fluids responsible for the main-stage ores of the Upper Mississippi Valley Zn-Pb district (75 degrees -113 degrees C, approximately 21 equiv wt % NaCl, delta D = -65 to -3ppm, and delta 18 O = -0.9-9.9ppm). The isotopic compositions (delta 13 C = -12.4 to -2.7ppm and delta 18 O = 21.1-25.8ppm) and paragenetic positions of the cleat calcite samples are similar to those of the late-stage calcite of the Upper Mississippi Valley Zn-Pb and Illinois-Kentucky fluorspar districts. Calcite inclusion fluids had delta D (sub H 2 O) values of -80 and -58 per mil, implying a meteoric water source. At probable temperatures of 15 degrees to 75 degrees C, this calcite formed from fluids having calculated delta 18 O (sub H 2 O) values of -9 to 1 per mil, implying slight to moderate exchange with sedimentary rocks. The diagenetic-epigenetic history of fluids recorded by the cleat minerals probably began with a slightly evolved seawater, followed by a metal-bearing deep basin brine, and concluded with a cooler, slightly evolved, meteoric-water fluid.

Economic Geology↗
USGS2022

Kentucky and Landsat

From its rolling pastures to its forested Appalachian peaks, Kentucky’s scenery offers beauty along with contrast. Rivers, including the Mississippi and the Ohio, border much of the State, and more rivers and hundreds of lakes are inside its borders. Kentucky is also home to the world’s longest known cave system, Mammoth Cave National Park, and its residents maintain long-held traditions of coal mining, farming, horse racing, and bourbon making. Although residents and visitors have a lot to explore up close, viewing Kentucky through a long lens—one extending into space—can offer even more information about its environmental and natural resources. Landsat satellite data can help State and Federal governments monitor the quality and health of Kentucky’s lands and waters. Here is a closer look at some of the many ways that Landsat benefits Kentucky.

Kentucky↗
USGS2018

Evaluation of the Radar Stage Sensor manufactured by Forest Technology Systems—Results of laboratory and field testing

Two identical Radar Stage Sensors from Forest Technology Systems were evaluated to determine if they are suitable for U.S. Geological Survey (USGS) hydrologic data collection. The sensors were evaluated in laboratory conditions to evaluate the distance accuracy of the sensor over the manufacturer’s specified operating temperatures and distance to water ranges. Laboratory results were compared to the manufacturer’s accuracy specification of ±0.007 foot (ft) and the USGS Office of Surface Water (OSW) policy requirement that water-level sensors have a measurement uncertainty of no more than 0.01 ft or 0.20 percent of the indicated reading. Both of the sensors tested were within the OSW policy requirement in both laboratory tests and within the manufacturer’s specification in the distance to water test over tested distances from 3 to 15 ft. In the temperature chamber test, both sensors were within the manufacturer’s specification for more than 90 percent of the data points collected over a temperature range of –40 to +60 degrees Celsius at a fixed distance of 8 ft. One sensor was subjected to an SDI-12 communication test, which it passed. A field test was conducted on one sensor at a USGS field site near Landon, Mississippi, from February 5 to March 29, 2016. Water-level measurements made by the radar during the field test were in agreement with those made by the Sutron Accubar Constant Flow Bubble Gauge. Upon the manufacturer’s release of updated firmware version 1.09, additional SDI-12 and temperature testing was performed to evaluate added SDI-12 functions and verify that performance was unaffected by the update. At this time, an Axiom data logger is required to perform a firmware update on this sensor. The data confirmed the results of the original test. Based on the test results, the Radar Stage Sensor is a suitable choice for USGS hydrologic data collection.

Open-File Report↗
USGS2022

Data-driven prospectivity modelling of sediment-hosted Zn-Pb mineral systems and their critical raw materials

Demand for critical raw materials is expected to accelerate over the next few decades due to continued population growth and the shifting consumption patterns of the global economy. Sedimentary basins are important sources for critical raw materials and new discoveries of sediment–hosted Mississippi Valley–type (MVT) and/or clastic–dominated (CD) Zn–Pb deposits are likely required to mitigate future supply chain disruptions for Zn, Pb, Ag, Cd, Ga, Ge, Sb, and In. Herein we integrate public geoscience datasets using a discrete global grid to system to model the mineral potential for MVT and CD deposits across Canada, the United States of America, and Australia. Statistical analysis of the model results demonstrates that surface–wave tomography and derivative products from satellite gravity datasets can be used to map the most favourable paleo–tectonic settings of MVT and CD deposits inboard of orogenic belts and at the rifted edges of cratonic lithosphere, respectively. Basin development at pre–existing crustal boundaries was likely important for maintaining the low geothermal–gradients that are favourable for metal transport and generating the crustal fluid pathways that were reactivated during ore–formation, as suggested by the statistical association of both sediment–hosted mineral deposit types with the edges of upward–continued gravity and long–wavelength magnetic anomalies. Multivariate statistical analysis demonstrates that the most prospective combination of these geophysical datasets varies for each geological region and deposit type. We further demonstrate that maximum and minimum geological ages, coupled with Phanerozoic paleogeographic reconstructions, represent mappable proxies for the availability of oxidized, brine–generating regions that are the most likely source of ore–forming fluids (e.g., low– to mid–latitude carbonate platforms and evaporites). Ore deposition was likely controlled by interaction between oxidized, low–temperature brines and sulfidic and/or carbonaceous rocks, which, in some cases, can be mapped at the exposed surface or identified using the available rock descriptions. Baseline weights–of–evidence models are based on regional geophysics and are the least impacted by missing surface information but yield relatively poor results, as demonstrated by the low area–under–the–curve (AUC) for the spatially independent test set on the success–rate plot (AUC = 0.787 for MVT and AUC = 0.870 for CD). Model performance can be improved by: (1) using advanced methods that were trained and validated during a series of semi–automated machine learning competitions; and/or (2) incorporating geological and geophysical datasets that are proxies for each component of the mineral system. The best–performing gradient boosting machine models yield higher AUC for the test set (AUC = 0.983 for MVT and AUC = 0.991 for CD) and reduce the search space by >94%. The model results highlight the potential benefits of mapping sediment–hosted mineral systems at continental scale to improve mineral exploration targeting for critical raw materials.

Ore Geology Reviews↗
USGS2012

Hydrologic and landscape database for the Cache and White River National Wildlife Refuges and contributing watersheds in Arkansas, Missouri, and Oklahoma

A hydrologic and landscape database was developed by the U.S. Geological Survey, in cooperation with the U.S. Fish and Wildlife Service, for the Cache River and White River National Wildlife Refuges and their contributing watersheds in Arkansas, Missouri, and Oklahoma. The database is composed of a set of ASCII files, Microsoft Access® files, Microsoft Excel® files, an Environmental Systems Research Institute (ESRI) ArcGIS® geodatabase, ESRI ArcGRID® raster datasets, and an ESRI ArcReader® published map. The database was developed as an assessment and evaluation tool to use in examining refuge-specific hydrologic patterns and trends as related to water availability for refuge ecosystems, habitats, and target species; and includes hydrologic time-series data, statistics, and hydroecological metrics that can be used to assess refuge hydrologic conditions and the availability of aquatic and riparian habitat. Landscape data that describe the refuge physiographic setting and the locations of hydrologic-data collection stations are also included in the database. Categories of landscape data include land cover, soil hydrologic characteristics, physiographic features, geographic and hydrographic boundaries, hydrographic features, regional runoff estimates, and gaging-station locations. The database geographic extent covers three hydrologic subregions—the Lower Mississippi–St Francis (0802), the Upper White (1101), and the Lower Arkansas (1111)—within which human activities, climatic variation, and hydrologic processes can potentially affect the hydrologic regime of the refuges and adjacent areas. Database construction has been automated to facilitate periodic updates with new data. The database report (1) serves as a user guide for the database, (2) describes the data-collection, data-reduction, and data-analysis methods used to construct the database, (3) provides a statistical and graphical description of the database, and (4) provides detailed information on the development of analytical techniques designed to assess water availability for ecological needs.

Arkansas;Missouri;Oklahoma↗