SEARCH · Search USGS

Results for “World & I”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52Linked to original sources

USGS1984

Characteristics of some silver-, and base metal-bearing, epithermal deposits of Mexico and Peru

Introduction Lithotectonic, mineralogical, and geochemical data on two silver- and base metal-bearing deposits from Peru and two from Mexico are compiled to facilitate comparisons with other epithermal deposits. Silver and base metal-bearing deposits of Mexico and Peru constitute an important portion of the world silver production derived from shallow, vein-type deposits hosted in volcanic rocks. Although these deposits are generally similar to epithermal deposits of Nevada and Colorado in the western United States, they have some important differences. Because of this, data on the geological attributes of these deposits are very useful for developing models of ore formation that can be used in mineral exploration. The data collected for this compilation are presented in the following pages in summaries of the important characteristics of each deposit. This compilation, which shows the complexities in the geology of epithermal ore deposits in Mexico and Peru, serves as a basis for further comparisons among epithermal deposits throughout the world. The case studies provide data useful to geologists and exploration!'sts interested in developing models of ore formation to be used in exploration for mineral deposits of this type. The deposits described in this report are the Guanajuato district of Guanajuato, Mexico, the Pachuca-Real del Monte district of Hidalgo, Mexico, the Colqui district of Lima, Peru, and the Julcani district of Huancavelica, Peru. Although many characteristics of the geology and geochemistry of this type of deposit were considered, the most important criterion for choosing these deposits was that they have substantial quantities of precious- and base-metal mineralization. Additional criteria for selecting the deposits were that they be hosted primarily by calc-alkaline volcanic rocks of intermediate to silicic composition and that they be younger than Tertiary in age. Many deposits in Mexico and Peru and other parts of Central and South America were excluded because the literature describing the districts is not readily available. Furthermore, many districts have not been examined in detail or the information available is of limited geological scope. The four districts that are compiled in this report were chosen because they are described in abundant literature dating from early mining reports on the general geology and mineralogy to very recent data on detailed geochemical and mineralogical studies. They were chosen as being fairly typical, classic examples of near-surface, low-temperature vein deposits as described by Lindgren (1928) in his treatise on ore deposits (Mineral deposits, McGraw-Hill, 1049 p.). These deposits are similar in aspects of their geology and geochemistry to many of the famous, epithermal silver mining districts in Colorado and Nevada including Creede, Colorado, Tonapah, Nevada, and the Sunnyside Mine of the Eureka district, Colorado, and, in the special case of Julcani, to Summitville, Colorado, and Goldfield, Nevada. The characteristics that distinguish them include overall size, production and alteration assemblage. The information documented in each summary will be used in a forthcoming series of papers on the comparative anatomy of precious and base metal deposits in North and South America.

Guanajuato, Hidalgo. Huancavelica, Lima↗

USGS1986

Trace-element contents of postorogenic granites of the eastern Arabian Shield, Kingdom of Saudi Arabia

Trace-element contents for 46 postorogenic granitoids vary by as much as two orders of magnitude; most samples are strongly enriched in incompatible elements (such as the heavy rare earths, yttrium, niobium, and uranium) and depleted in the compatible elements (such as barium, strontium, scandium, europium, and cobalt). These trace-element characteristics are typical of A-type granites found in other areas of the world. In spite of the wide range in trace-element contents, no samples contained economically significant concentrations of a single element. Samples range from peralkaline to strongly peraluminous; most are weakly peraluminous or metaluminous. All three subgroups (peralkaline, metaluminous, and peraluminous) are enriched in uranium and hafnium and are depleted in compatible elements. The peralkaline granites are generally enriched in yttrium and niobium - the strongly peraluminous granites in rubidium and tantalum; both groups are also somewhat enriched in the heavy-rare-earth elements. Several of the peraluminous granites are known to be tin-bearing and, like tin-bearing granites found elsewhere in the world, their chondrite-normalized, rare-earth-element patterns are flat and have large negative europium anomalies. Samples from several plutons have very anomalous ratios for geochemically similar elements such as yttrium and holmium, niobium and tantalum, and zirconium and hafnium. These ratios may reflect differential complexing with a halogen-rich aqueous phase that may be characteristic of plutons that have been subjected to an ore-forming process. A program to test these hypotheses, through study of known mineralized areas and laboratory experiments, should be implemented. The regional trends for the chemical data and geochemical correlations over the large area sampled, suggest that the postorogenic granites were derived from a single protolith that formed by the mixing of oceanic sediments from the west, continental sediments from the east.

Open-File Report↗

USGS1986

Water resources scientific information center

The Water Resources Scientific Information Center (WRSIC) acquires, abstracts and indexes the major water resources related literature of the world, and makes information available to the water resources community and the public. A component of the Water Resources Division of the US Geological Survey, the Center maintains a searchable computerized bibliographic data base, and publishers a monthly journal of abstracts. Through its services, the Center is able to provide reliable scientific and technical information about the most recent water resources developments, as well as long-term trends and changes. WRSIC was established in 1966 by the Secretary of the Interior to further the objectives of the Water Resources Research Act of 1964--legislation that encouraged research in water resources and the prevention of needless duplication of research efforts. It was determined the WRSIC should be the national center for information on water resources, covering research reports, scientific journals, and other water resources literature of the world. WRSIC would evaluate all water resources literature, catalog selected articles, and make the information available in publications or by computer access. In this way WRSIC would increase the availability and awareness of water related scientific and technical information. (Lantz-PTT)

Open-File Report↗

USGS1989

IRIS/USGS plans for upgrading the Global Seismograph Network

This report has been prepared to provide information to organizations that may be asked to participate in a program to upgrade the global seismographic network. In most cases, the organizations that will be offered new instrumentation by the U.S. Geological Survey currently operate stations in the World-Wide Standardized Seismograph Network (WWSSN) or the Global Digital Seismograph Network (GDSN). The deployment of the WWSSN in the 1960's and the subsequent equipping of some WWSSN stations with digital equipment and borehole seismometers during the 1970's has been a remarkably successful program that generated the high- quality data needed to fuel an unprecedented period of progress in earthquake and tectonic research. The success of the WWSSN can be attributed to the importance of the data, to the strong commitment by participating organizations to international scientific cooperation, to the dedication and skill of the station operators, and to the resourcefulness of the staff supporting the network. Benefits have been widespread. The community of scientists world-wide has benefited from unrestricted access to a standardized base of calibrated data, and the participating stations have benefited from the donation of modern observatory instruments that have been useful for local earthquake studies and for the training of scientists and engineers. Now, an exciting opportunity has arisen to deploy a new generation of seismograph systems to replace the outdated equipment at many of the WWSSN and GDSN stations. The U.S. Geological Survey (USGS) is cooperating with the Incorporated Research Institutions for Seismology (IRIS) in a program to upgrade the global seismograph network. The equipment development phase is nearly complete with a prototype of the new broadband seismograph system currently undergoing final testing at the USGS Albuquerque Seismological Laboratory. Deployment of the new equipment is expected to begin in early 1990. As this report will demonstrate, the IRIS broadband seismograph system combines the very latest data acquisition and computer technology to produce seismic data with unprecedented bandwidth and dynamic range. Moreover, the system has been designed so that the high-quality digital data are accessible for local display and analysis. The functional design of the new system, which uses off-the-shelf modules and a standard computer bus, will make it much easier than it has been in the past to modify and upgrade the data acquisition system as improvements in technology become available. With adequate support for the program, the new IRIS seismograph system need never become obsolete. We want you to be aware of our plans and the possibility that you may be asked to participate in this ,program. The schedule for upgrading WWSSN and GDSN stations depends on the level of funding earmarked for the program by our National Science Foundation. We hope to deploy at least ten new GSN data systems each year. If you have any questions concerning this program, please contact the Albuquerque Seismological Laboratory, U.S. Geological Survey, Albuquerque, New Mexico 87115-5000. This report was revised in February 1992 in order to update information concerning the current program and instrumentation. The amp in Figure 1 was revised in June 1993, April 1994, December 1994, and September 1996 to reflect updated siting information. In September 1996 a composite photo of standard and optional components of the IRIS-2 GSN system hardware was added as a separate page between Figures 9 and 10.

Open-File Report↗

USGS1990

A numerical study of some potential sources of error in side-by-side seismometer evaluations

This report presents the results of a series of computer simulations of potential errors in test data, which might be obtained when conducting side-by-side comparisons of seismometers. These results can be used as guides in estimating potential sources and magnitudes of errors one might expect when analyzing real test data. First, the derivation of a direct method for calculating the noise levels of two sensors in a side-by-side evaluation is repeated and extended slightly herein. This bulk of this derivation was presented previously (see Holcomb 1989); it is repeated here for easy reference. This method is applied to the analysis of a simulated test of two sensors in a side-by-side test in which the outputs of both sensors consist of white noise spectra with known signal-tonoise ratios (SNR's). This report extends this analysis to high SNR's to determine the limitations of the direct method for calculating the noise levels at signal-to-noise levels which are much higher than presented previously (see Holcomb 1989). Next, the method is used to analyze a simulated test of two sensors in a side-by-side test in which the outputs of both sensors consist of bandshaped noise spectra with known signal-tonoise ratios. This is a much more realistic representation of real world data because the earth's background spectrum is certainly not flat. Finally, the results of the analysis of simulated white and bandshaped side-by-side test data are used to assist in interpreting the analysis of the effects of simulated azimuthal misalignment in side-by-side sensor evaluations. A thorough understanding of azimuthal misalignment errors is important because of the physical impossibility of perfectly aligning two sensors in a real world situation. The analysis herein indicates that alignment errors place lower limits on the levels of system noise which can be resolved in a side-by-side measurement It also indicates that alignment errors are the source of the fact that real data noise spectra tend to follow the earth's background spectra in shape.

Open-File Report↗

USGS1997

Reports and maps of the Military Geology Unit, 1942-1975

Included here are reports and maps which were prepared in the Military Geology Unit of the U. S. Geological Survey from 1942 through 1975. In addition to the references prepared primarily for military use and listed here, more than 200 reports of more general geologic interest were prepared for publication as Survey bulletins and professional papers and in outside journals. These reports are listed in "Publications of the Geological Survey" and other bibliographies. Military Geology reports generally include basic subjects such as rock types, soils, water resources, landforms and vegetation, as well as interpretive subjects such as suitability of terrain for cross-country movement and for construction of roads and airfields in areas throughout the world. Reports on specific areas range from generalized texts with small scab maps derived from published sources to detailed texts with large-scale maps commonly based on photo-interpretation and, especially for Alaska and western Pacific islands, involving field mapping. Other reports treat topics of interest in military geology without reference to specific areas. A number of reports covering the moon include the first photogeologic map of the near side. Authors are cited for some kinds of reports; however, many intelligence reports were published anonymously. Most of the reports were prepared by teams made up mainly of geologists but commonly including soils scientists, botanists, climatologists and geographers. Nearly all the soil scientists and climatologists were members of the World Soil Geography Unit, Soil Survey, Soil Conservation Service, U. S. Department of Agriculture. Manuscripts from this Unit were passed through a common review and other processing, as were the manuscripts originating in the Military Geology office, to be issued under the aegis of the latter. In some instances where it has not been possible to list all authors, names of project supervisors are given. File copies of many of the Military Geology reports prepared since 1975 are kept in the Special Geologic Studies Group, U.S. Geological Survey, National Center, Reston, and may be examined there by appropriately cleared persons. Additionally, copies of many of the unclassified studies are in the U.S. Geological Survey Library. Some of the older reports are in the files of the Terrain Analysis Center, Fort Belvoir, Virginia, and other offices within the Corps of Engineers. Most of the reports are out of print and many of the other studies are no longer available.

Open-File Report↗

USGS1998

Database of significant deposits of gold, silver, copper, lead, and zinc in the United States

It has long been recognized that the largest mineral deposits contain most of the known mineral endowment (Singer and DeYoung, 1980). Sometimes called giant or world-class deposits, these largest deposits account for a very large share of historic and current mineral production and resources in industrial society (Singer, 1995). For example, Singer (1995) shows that the largest 10 percent of the world’s gold deposits contain 86 percent of the gold discovered to date. Many mineral resource issues and investigations are more easily addressed if limited to the relatively small number of deposits that contain most of the known mineral resources. An estimate of known resources using just these deposits would normally be sufficient, because considering smaller deposits would not add significantly to the total estimate. Land-use planning should treat mainly with these deposits due to their relative scarcity, the large share of known resources they contain, and the fact that economies of scale allow minerals to be produced much more cheaply from larger deposits. Investigation of environmental and other hazards that result from mining operations can be limited to these largest deposits because they account for most of past and current production. The National Mineral Resource Assessment project of the U.S. Geological Survey (USGS) has compiled a database on the largest known deposits of gold, silver, copper, lead, and zinc in the United States to complement the 1996 national assessment of undiscovered deposits of these same metals (Ludington and Cox, 1996). The deposits in this database account for approximately 99 percent of domestic production of these metals and probably a similar share of identified resources. These data may be compared with results of the assessment of undiscovered resources to characterize the nation’s total mineral endowment for these metals. This database is a starting point for any national or regional mineral-resource or mineral-environmental investigation.

Open-File Report↗

USGS1998

Contributions to the gold metallogeny of northern Nevada

Nevada is one of the Earth's premier gold producing regions, accounting for approximately 64 percent of the U.S and nine percent of the world total. The impact of these mines on nearby local economies and on our national balance of payments is profound, and will continue well into the next century. Of principal importance in this region are giant sedimentary-rock-hosted (Carlin-type) deposits. These are some of the world's largest deposits, but yet are poorly understood. Other sedimentary-rock hosted deposits in the region, the distal-disseminated Ag-Au type, are genetically related to shallow plutonic complexes. Hot-spring gold-silver systems associated with Tertiary volcanic rocks represent a third type of precious metal deposit in northern Nevada. These deposits, despite being generally smaller than sedimentary-rock-hosted gold deposits, are also important gold-silver resources. Aspects about the geologic and metallogenic setting of gold-silver deposits in northern Nevada are addressed in the twenty-two chapters that compose this volume. The volume is organized along four themes: (1) crustal structure; (2) Carlin-type deposits; (3) pluton-related gold-silver deposits near Battle Mountain; and (4) hot-spring gold-silver deposits. This Open-File Report, the result of ongoing geologic and mineral-resource investigations, provides a basis for mineral exploration, for land-use planning decisions, and for environmental questions in northern Nevada.

Open-File Report↗

USGS1998

Contributions to the gold metallogeny of northern Nevada

Open-File Report↗

USGS1998

Experimental investigations regarding the use of sand as an inhibitor of air convection in deep seismic boreholes

Tilt has been the nemesis of horizontal long period seismology since its inception. Modern horizontal long period seismometers with their long natural periods are incredibly sensitive to tilt. They can sense tilts smaller than 10 -11 radians. To most readers, this is just a very very small number, so we will begin with an example, which should help to illustrate just how small 10 -11 radians is. Suppose we have an absolutely rigid rod which is approximately 4170 kilometers long; this just happens to be the Rand McNally map scaled crow flight distance between Los Angeles and Boston. Tilting this rod 10 -11 radians corresponds to raising one end of the rod 0.0000417 meters. Alas, this is just another very very small number! However, this corresponds to slipping a little less than one third a sheet of ordinary copying paper under one end of this perfectly rigid rod. To clarify, we mean, take a sheet of paper just like the paper this report is printed on and split it a little less than one third in the thickness direction, then put it under the end of the 4170 kilometer long rod! This will tilt the rod 10 -11 radians. Real world seismometers are nowhere near the length of this rod. A KS-54000 is about two meters long. Tilting a rod only two meters long 10~n radians corresponds to moving one end of this rod a mere 0.00000000002 meters or 0.02 millimicrons. As one of the authors old math teachers used to say, "That's PDS" (PDS = Pretty Damn Small). Unfortunately, the long period seismologist does not have the luxury of ignoring PDS numbers when it suits him as the mathematician frequently does. He must live in the real world in which tilts this small create severe contamination of long period seismic data. At periods longer than 20 seconds, tilt noise contaminates the long period data from all instruments installed on or near the earth's surface. Many years of experimentation revealed that installing the sensors at depth in deep mines drastically reduced the level of tilt noise in long period data. However, low levels of tilt noise persisted even at great depth; this noise was caused by air convection in the vault in which the sensors were installed. Over the years, methods were developed to control the air motion with mechanical barriers (boxes) around the sensors and by stratifying (creating a situation in which the air temperature increases with height) the air in the vault near the seismometer. These methods decreased tilt noise in deep mines to very low levels. However, deep mines, that are economically and environmentally suitable and accessible to seismology, are not plentiful and are not evenly distributed over the earth's surface. Therefore, the borehole deployable Teledyne Geotech KS-36000 and later the KS-54000 sensor systems were developed to fulfill the need for instruments that could be installed at depth wherever high quality long period data was desired. Early in the development program, it became evident to the Teledyne Geotech personnel that air convection within the borehole was going to be a significant problem in KS deployments. Experimental and theoretical investigations conducted by Teledyne Geotech (see Douze and Sherwin, 1975, and Sherwin and Cook, 1976) produced a list of recommended installation procedures for reducing the effects of air convection. These procedures consisted of wrapping the sensor in a relatively thin layer of foam insulation, filling the free space volume in the vicinity of the centralizer-bail assembly with foam insulation, and the installation of styrofoam hole plugs immediately above the cable strain relief assembly at the top of the sensor package and at the top of the borehole. This technology has performed quite satisfactorily for over 20 years but evidence of tilt noise in the system output has persisted throughout the KS deployment program (the evidence was that the horizontal components were usually noisier than the vertical components) even in deep boreholes. Some deep borehole sites have been plagued by quite high levels of horizontal noise. Therefore, there has been a definite need for a new technique for controlling low level tilt noise in deep boreholes and the use of sand has been under consideration for several years. Figure 1 contains conceptual illustrations of both the conventional holelock installed KS sensor system and the same sensor installed in sand. This figure demonstrates the major differences between the two installation methods. The curved arrows in the borehole on the left in the figure denote possible air convection cells which are believed to be the source of tilt noise in some of the conventional installations. This air motion is eliminated in a sand installation by filling most of the free air volume surrounding the seismometer with sand as shown in the right hand portion of the figure. The sand actually performs two functions; it prevents air motion and provides a remarkably ridgid clamping of the seismometer in the borehole. This report presents the results of quantitative experimental investigations into the effectiveness of controlling low level air convection in seismic borehole installations with sand. The main body of the experimental effort consisted of installing two KS-540001 sensor systems in closely spaced shallow boreholes, allowing the sensors to reach equilibrium operation, and then pouring sand into both boreholes to observe any changes caused by pouring sand into the holes. The hypothesis of the experiment was that the sand would fill up the entire free air volume between the sensor package and the borehole walls thereby preventing movement of the air in the vicinity of the sensor package. The validity of this hypothesis had been qualitatively proven by earlier experiments at ASL and by the sand installations at the IRIS/ASL stations ANMO in 1995 and COLA in 1996. This experiment documents the degree of improved noise levels to be expected if KS instruments are installed in sand instead of in the conventional manner.

Open-File Report↗

USGS1998

Comparative geology and geochemistry of sedimentary-rock-hosted (Carlin Type) gold deposits in the People's Republic of China and in Nevada, USA

Sedimentary-rock-hosted (Carlin-type) gold deposits have been considered economically significant and geologically distinct since the early 1960's. This report consists of a nine-part text and an interactive database. This small database is to help Western companies get more information about these gold deposits in China, and to help geologists who are interested in world Carlin-type deposits conduct research on them. Because of their economic significance and geological distinctiveness, these deposits have caught the interest of economic geologists all over the world since the early 1960's. Similar deposits have been discovered in China, Australia, Dominican Republic, Spain, and Russia besides Nevada. Perhaps most significant are the 165 Carlin-type gold deposits that were found in southwest China during the past 15 years. Of these, at least 19 deposits have proven to be of substantial tonnage, making China the second leading country to exploit such deposits. With the increasing interest in Chinese Carlin-type gold deposits, some western companies and geologists desire to get more information about these Chinese deposits. This seems to have been very difficult because the literature was in Chinese. It is estimated that several hundred scientific publications (including papers, books, and technical reports) have been published. This database of Chinese Carlin-type Gold deposits is built on the documentation published during the most recent 10 years and includes six subjects, which consist of 165 records and 30 fields. A new Proterozoic-age sedimentary-rock-hosted gold deposit in northeastern P.R. China also is described. Note that for the old version 1.1 on the CD-ROM, the latitude and longitude locations of the mineral occurrences have been estimated from sketch maps and journal articles and are not intended for digital analysis. One of the improvements in this version 1.2 is the accuracy of geographic data. Version 1.3 updates to the database and includes maps and photos of deposits, deposit information and a geochemical model. See the version history for details.

Open-File Report↗

USGS1929

The copper deposits of Michigan

The copper district of Keweenaw Point, in the northern peninsula of Michigan, is the second largest producer of copper in the world. The output of the district since 1845 has been more than 7,500,000,000 pounds and showed a rather steady and consistent increase from the beginning of production to the end of the World War in 1918, since which there has been a marked decrease.

Michigan↗

USGS1998

Chapter A. The Loma Prieta, California, Earthquake of October 17, 1989 - Lifelines

To the general public who had their televisions tuned to watch the World Series, the 1989 Loma Prieta earthquake was a lifelines earthquake. It was the images seen around the world of the collapsed Cypress Street viaduct, with the frantic and heroic efforts to pull survivors from the structure that was billowing smoke; the collapsed section of the San Francisco-Oakland Bay Bridge and subsequent home video of a car plunging off the open span; and the spectacular fire in the Marina District of San Francisco fed by a broken gasline. To many of the residents of the San Francisco Bay region, the relation of lifelines to the earthquake was characterized by sitting in the dark because of power outage, the inability to make telephone calls because of network congestion, and the slow and snarled traffic. Had the public been aware of the actions of the engineers and tradespeople working for the utilities and other lifeline organizations on the emergency response and restoration of lifelines, the lifeline characteristics of this earthquake would have been even more significant. Unobserved by the public were the warlike devastation in several electrical-power substations, the 13 miles of gas-distribution lines that had to be replaced in several communities, and the more than 1,200 leaks and breaks in water mains and service connections that had to be excavated and repaired. Like the 1971 San Fernando, Calif., earthquake, which was a seminal event for activity to improve the earthquake performance of lifelines, the 1989 Loma Prieta earthquake demonstrated that the tasks of preparing lifelines in 'earthquake country' were incomplete-indeed, new lessons had to be learned.

Professional Paper↗

USGS2002

Habitat and environment of islands: primary and supplemental island sets

The original intent of the study was to develop a first-order synopsis of island hydrology with an integrated geologic basis on a global scale. As the study progressed, the aim was broadened to provide a framework for subsequent assessments on large regional or global scales of island resources and impacts on those resources that are derived from global changes. Fundamental to the study was the development of a comprehensive framework?a wide range of parameters that describe a set of 'saltwater' islands sufficiently large to Characterize the spatial distribution of the world?s islands; Account for all major archipelagos; Account for almost all oceanically isolated islands, and Account collectively for a very large proportion of the total area of the world?s islands whereby additional islands would only marginally contribute to the representativeness and accountability of the island set. The comprehensive framework, which is referred to as the ?Primary Island Set,? is built on 122 parameters that describe 1,000 islands. To complement the investigations based on the Primary Island Set, two supplemental island sets, Set A?Other Islands (not in the Primary Island Set) and Set B?Lagoonal Atolls, are included in the study. The Primary Island Set, together with the Supplemental Island Sets A and B, provides a framework that can be used in various scientific disciplines for their island-based studies on broad regional or global scales. The study uses an informal, coherent, geophysical organization of the islands that belong to the three island sets. The organization is in the form of a global island chain, which is a particular sequential ordering of the islands referred to as the 'Alisida.' The Alisida was developed through a trial-and-error procedure by seeking to strike a balance between 'minimizing the length of the global chain' and 'maximizing the chain?s geophysical coherence.' The fact that an objective function cannot be minimized and maximized simultaneously indicates that the Alisida is not unique. Global island chains other than the Alisida may better serve disciplines other than those of hydrology and geology.

Professional Paper↗

USGS2014

Bituminous coal production in the Appalachian basin: past, present, and future

Although small quantities of coal first were produced from the Appalachian basin in the early 1700s, the first production statistics of significance were gathered during the census of 1830 (Eavenson, 1942). Since then, about 35 billion short tons of bituminous coal have been produced from the Appalachian basin from an original potential coal reserve (PCR (o) ) estimated to range from about 60 to 90 billion short tons. The term “reserve” refers to economically producible coal, and a “potential coal reserve” (PCR (n) ) is an estimate of the amount of coal economically recoverable in a region (State, coal field) over a defined time period (n = number of years) and under a range of economic, societal, and technological conditions. Thus, the current cumulative production plus the PCR (n) equals an estimated cumulative production (ECP (n) ). The maps in this report (oversized figures 1, 2, 3, and 4) were produced from a digital database of historical and current coal production records by county. Sources of the original data include various State geological surveys, the U.S. Geological Survey, the former U.S. Bureau of Mines, and the U.S. Department of Energy’s Energy Information Administration. This report is part of the U.S. Geological Survey’s National Coal Resource Assessment Project. The Appalachian basin consistently has lead all other regions of the country in coal production and, until 1970, produced 70 percent or more of the coal produced in the Nation (fig. 5). Since 1970, however, the relative amount of coal coming from the Appalachian basin has declined from about 70 percent to 43 percent. Historically, coal production from the Appalachian basin may be divided into three economically driven cycles: (1) from the inception of exploration and development of the resource through World War I (1914) to the Depression (1929 to the early 1940s); (2) from the Depression through World War II (1944) to the production decline in 1961; and (3) from 1961 through the current period of increasing demand for coal by the electric power industry (fig. 6). Annual coal production from the Appalachian basin peaked in 1997 at 476.8 million tons and has since declined to 375.3 million tons as of 2003. This report on Appalachian basin coal production consists of four plates and associated graphs and tables that were used to construct the maps. Figure 1 shows the decade of greatest coal production by county. Figure 2 shows the amount of coal produced for each county (in thousands of short tons) during the year of greatest coal production. These data are sorted by decade. Figure 3 illustrates the cumulative coal production (in thousands of short tons) for each county since about the beginning of the 20th century. Figure 4 shows 2003 production by county in thousands of short tons.

Appalachian basin↗

USGS2006

Rates, trends, causes, and consequences of urban land-use change in the United States

Over the past 200 years, changes to the Nation's urban areas have been dramatic. Changes that have occurred relate both to the location of urban centers, as well as to the spatial extent of land dedicated to urban uses. Urban areas at the beginning of the 19th century were located primarily along major rivers or bodies of water, as waterways provided the most efficient means for transporting goods and people. As railroads became prominent, urban areas were able to expand or develop away from the water's edge. Geographic features such as steep slopes, wetlands, and lack of freshwater impeded settlement. In 1902, the National Reclamation Act was passed and with it came funding for the construction of water storage and transportation systems. This encouraged urban expansion in the arid west. After World War II, the Nation's urban areas continued to expand outward away from the city center as populations migrated to the margins of urban areas, where land was less expensive and the environment was less polluted. In 1956, the Federal Highway Act and the building of Interstate highways further facilitated urban expansion across the Unite States. Rural towns, small industrial centers, and farmland were engulfed by expanding urban centers. Over the past 200 years, numerous social, cultural, economic, and political incentives have encouraged urban expansion. In the 1800s, the industrial revolution influenced where people lived and worked. Many people shifted from agricultural production in rural areas to factory work in urban centers. Advances in transportation systems, such as rail transport in the 19th and early 20th centuries, followed by the mass production of the automobile and convenient air travel, facilitated a mobile society and a national economy. Economic growth and a population boom after World War II spurred increased suburbanization-the shifting of residential areas to the outlying section of a city or to a separate municipality-on the fringe of urban areas. Other economic and political incentives that shaped the urban environment included Federally backed home loans, credit and tax mechanisms that encouraged new development, and less restrictive municipal ordinances regarding building codes, environmental laws, and zoning regulations. Throughout the past two centuries land use changes associated with increasing urbanization have had impacts that resonate at local, regional, and even national scales. Landscape changes resulting from urbanization can be mapped and studied over time. Understanding these changes requires a study of the causes of change as related to social, economic, and political influences. Understanding these changes also requires analysis of how urbanization physically spreads across the landscape. The knowledge gained from studying urban land-use change can be helpful when it flows into local, regional, and national decisionmaking that relates to land-use decisions that impact the people, the economy, and the environment. Deriving a correlation between physical change and the explanations of the causes of change can help anticipate and mitigate the impacts of future change. Throughout the past two centuries changes to the Nation's urban areas are inextricably linked to population changes. The Nation's population started growing slowly along the eastern seaboard during the 17th and 18th centuries, accelerated in the second half of the 19th century, and then continued steadily spreading westward throughout the next hundred years. Currently, nearly 80 percent of the U.S. population resides in urban areas. Land area dedicated to urban use continues to expand, although differently than it has in the past. Most newly urbanized areas are much less densely populated and less intensively developed than they were 50 to 100 years ago.

Professional Paper↗

USGS2014

The Hawaiian Volcano Observatory: A natural laboratory for studying basaltic volcanism

In the beginning of the 20th century, geologist Thomas A. Jaggar, Jr., argued that, to fully understand volcanic and associated hazards, the expeditionary mode of studying eruptions only after they occurred was inadequate. Instead, he fervently advocated the use of permanent observatories to record and measure volcanic phenomena—at and below the surface—before, during, and after eruptions to obtain the basic scientific information needed to protect people and property from volcanic hazards. With the crucial early help of American volcanologist Frank Alvord Perret and the Hawaiian business community, the Hawaiian Volcano Observatory (HVO) was established in 1912, and Jaggar’s vision became reality. From its inception, HVO’s mission has centered on several goals: (1) measuring and documenting the seismic, eruptive, and geodetic processes of active Hawaiian volcanoes (principally Kīlauea and Mauna Loa); (2) geological mapping and dating of deposits to reconstruct volcanic histories, understand island evolution, and determine eruptive frequencies and volcanic hazards; (3) systematically collecting eruptive products, including gases, for laboratory analysis; and (4) widely disseminating observatory-acquired data and analysis, reports, and hazard warnings to the global scientific community, emergency-management authorities, news media, and the public. The long-term focus on these goals by HVO scientists, in collaboration with investigators from many other organizations, continues to fulfill Jaggar’s career-long vision of reducing risks from volcanic and earthquake hazards across the globe. This chapter summarizes HVO’s history and some of the scientific achievements made possible by this permanent observatory over the past century as it grew from a small wooden structure with only a small staff and few instruments to a modern, well-staffed, world-class facility with state-of-the-art monitoring networks that constantly track volcanic and earthquake activity. The many successes of HVO, from improving basic knowledge about basaltic volcanism to providing hands-on experience and training for hundreds of scientists and students and serving as the testing ground for new instruments and technologies, stem directly from the acquisition, integration, and analysis of multiple datasets that span many decades of observations of frequent eruptive activity. HVO’s history of the compilation, interpretation, and communication of long-term volcano monitoring and eruption data (for instance, seismic, geodetic, and petrologic-geochemical data and detailed eruption chronologies) is perhaps unparalleled in the world community of volcano observatories. The discussion and conclusions drawn in this chapter, which emphasize developments since the 75th anniversary of HVO in 1987, are general and retrospective and are intended to provide context for the more detailed, topically focused chapters of this volume.

Hawaii↗

USGS2017

Environmental considerations related to mining of nonfuel minerals

Throughout most of human history, environmental stewardship during mining has not been a priority partly because of the lack of applicable laws and regulations and partly because of ignorance about the effects that mining can have on the environment. In the United States, the National Environmental Policy Act of 1969, in conjunction with related laws, codified a more modern approach to mining, including the responsibility for environmental stewardship, and provided a framework for incorporating environmental protection into mine planning. Today, similar frameworks are in place in the other developed countries of the world, and international mining companies generally follow similar procedures wherever they work in the world. The regulatory guidance has fostered an international effort among all stakeholders to identify best practices for environmental stewardship. The modern approach to mining using best practices involves the following: (a) establishment of a pre-mining baseline from which to monitor environmental effects during mining and help establish geologically reasonable closure goals; (b) identification of environmental risks related to mining through standardized approaches; and (c) formulation of an environmental closure plan before the start of mining. A key aspect of identifying the environmental risks and mitigating those risks is understanding how the risks vary from one deposit type to another—a concept that forms the basis for geoenvironmental mineral-deposit models. Accompanying the quest for best practices is the goal of making mining sustainable into the future. Sustainable mine development is generally considered to be development that meets the needs of the present generation without compromising the ability of future generations to meet their own needs. The concept extends beyond the availability of nonrenewable mineral commodities and includes the environmental and social effects of mine development. Global population growth, meanwhile, has decreased the percentage of inhabitable land available to support society’s material needs. Presently, the land area available to supply the mineral resources, energy resources, water, food, shelter, and waste disposal needs of all Earth’s inhabitants is estimated to be 135 square meters per person. Continued global population growth will only increase the challenges of sustainable mining. Current trends in mining are also expected to lead to new environmental challenges in the future, among which are mine-waste management issues related to mining larger deposits for lower ore grade; water-management issues related to both the mining of larger deposits and the changes in precipitation brought about by climate change; and greenhouse gas issues related to reducing the carbon footprint of larger, more energy-intensive mining operations.

Professional Paper↗