SEARCH · Search USGS

Results for “The Sedimentary Record”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17Linked to original sources

USGS2020

Site response, basin amplification, and earthquake stress drops in the Portland, Oregon area

Site response, sedimentary basin amplification, and earthquake stress drops for the Portland, Oregon area were determined using accelerometer recordings at 16 sites of 10 local earthquakes with M D "> M D MD 2.6–4.0. A nonlinear inversion was applied to calculate site response (0.5–10 Hz), corner frequencies, and seismic moments from the Fourier spectra of the earthquakes. Site amplifications at lower frequencies of 0.1–2.0 Hz were determined from Fourier spectra of four regional earthquakes with M w "> M w Mw 5.8–6.4. Amplifications were calculated relative to a stiff‐soil site outside the Portland and Tualatin basins. Sites on artificial fill and Holocene alluvium show strong amplification peaks (factor of 5) around 1–2 Hz. Sites on the Portland Hills, consisting of thin soil over basalt, display spectral peaks at 4–5 Hz (factor of 4). Spectral peaks at both sites are similar to those predicted for vertically propagating S waves from V S "> V S VS profiles determined at these sites using a borehole and refraction microtremor analysis. The largest amplifications at 0.1–1 Hz were found at stiff‐soil sites in the Tualatin basin, based on recordings of regional earthquakes. Amplifications of a factor of 10, at about 0.3 Hz, were observed for a site in the deeper portion of the Tualatin basin and a factor of 7 at 0.5–0.6 Hz for two adjacent sites closer to the border of that basin. Stiff‐soil sites in the Portland basin exhibit amplifications of 2–3 at frequencies of about 0.3–0.8 Hz. The frequencies of the amplification peaks for the deep Tualatin basin site can be explained by S ‐wave resonance in the shallow sediments, but the observed amplification is underestimated. Earthquake stress drops determined from the inversion range from 3 to 11 MPa, with no overall dependence on seismic moment.

Oregon↗

USGS2003

Geologic map and digital database of the Yucaipa 7.5’ quadrangle, San Bernardino and Riverside Counties, California

Introduction This geologic database of the Yucaipa 7.5' quadrangle was prepared by the Southern California Areal Mapping Project (SCAMP), a regional geologic-mapping project sponsored jointly by the U.S. Geological Survey and the California Geological Survey. The database was developed as a contribution to the National Cooperative Geologic Mapping Program's National Geologic Map Database, and is intended to provide a general geologic setting of the Yucaipa quadrangle. The database and map provide information about earth materials and geologic structures, including faults and folds that have developed in the quadrangle due to complexities in the San Andreas Fault system. The Yucaipa 7.5' quadrangle contains materials and structures that provide unique insight into the Mesozoic and Cenozoic geologic evolution of southern California. Stratigraphic and structural elements include: (1) strands of the San Andreas Fault that bound far-traveled terranes of crystalline and sedimentary rock; (2) Mesozoic crystalline rocks that form lower and upper plates of the regionwide Vincent-Orocopia Thrust system; and (3) late Tertiary and Quaternary sedimentary materials and geologic structures that formed during the last million years or so and that record complex geologic interactions within the San Andreas Fault system. These materials and the structures that deform them provide the geologic framework for investigations of geologic hazards and ground-water recharge and subsurface flow. Geologic information contained in the Yucaipa database is general-purpose data that is applicable to land-related investigations in the earth and biological sciences. The term "generalpurpose" means that all geologic-feature classes have minimal information content adequate to characterize their general geologic characteristics and to interpret their general geologic history. However, no single feature class has enough information to definitively characterize its properties and origin. For this reason the database cannot be used for site-specific geologic evaluations, although it can be used to plan and guide investigations at the site-specific level.

California↗

USGS2003

Geologic map and digital database of the Redlands 7.5' quadrangle, San Bernardino and Riverside Counties, California

This geologic database of the Redlands 7.5' quadrangle was prepared by the Southern California Areal Mapping Project (SCAMP), a regional geologic-mapping project sponsored jointly by the U.S. Geological Survey and the California Geological Survey. The database was developed as a contribution to the National Cooperative Geologic Mapping Program's National Geologic Map Database, and is intended to provide a general geologic setting of the Redlands quadrangle. The database and map provide information about earth materials and geologic structures, including faults and folds that have developed in the quadrangle due to complexities in the San Andreas Fault system. The Redlands 7.5' quadrangle contains earth materials and structures that provide insight into the late Cenozoic geologic evolution of the southern California Inland Empire region. Important stratigraphic and structural elements include (1) the modern trace of the San Andreas and San Jacinto faults and (2) late Tertiary and Quaternary sedimentary materials and geologic structures that formed during the last million years or so and that record complex geologic interactions within the San Andreas Fault system. These materials and the structures that deform them provide the geologic framework for investigations of earthquake hazards and ground-water recharge and subsurface flow. Geologic information contained in the Redlands database is general-purpose data that is applicable to land-related investigations in the earth and biological sciences. The term "general-purpose" means that all geologic-feature classes have minimal information content adequate to characterize their general geologic characteristics and to interpret their general geologic history. However, no single feature class has enough information to definitively characterize its properties and origin. For this reason the database cannot be used for site-specific geologic evaluations, although it can be used to plan and guide investigations at the site-specific level. This summary pamphlet discusses major categories of surficial materials in the Redlands quadrangle, and provides a conceptual framework and basis for how geologicmap units containing such materials are recognized and correlated.

California↗

USGS1981

Sedimentary framework of the Potomac River estuary, Maryland

Analyses of seismic-reflection profiles, sediment cores, grab samples, and side-scan sonar records, along with previously collected borehole data, reveal the characteristics, distribution, and geologic history of the shallow strata beneath the Potomac River estuary. The lowermost strata are sediments of the Chesapeake Group (lower Miocene to lower Pleistocene) that crop out on land near the shore but are buried as much as 40 m below the floor of the estuary. The top of these sediments is an erosional unconformity that outlines the Wisconsinan valley of the Potomac River. This valley has a sinuous trend, a flat bottom, a relief of 15 to 34 m, and axial depths of 34 to 54 m below present sea level. During the Holocene transgression of sea level, the ancestral valley was filled with as much as 40 m of sandy and silty, fluvial-to-shallow estuarine sediments. The fill became the substrate for oyster bars in the upper reach and now forms most marginal slopes of the estuary. Since sea level approached its present position (2,000 to 3,000 yr ago), the main channel has become the locus of deposition for watery, gray to black clay or silty clay, and waves and currents have eroded the heterogeneous Quaternary sediments along the margins, leaving winnowed brown sand on shallow shoreline flats. Pb-210 analyses indicate that modern mud is accumulating at rates ranging from 0.16 to 1.80 cm/yr, being lowest near the mouth and increasing toward the head of the estuary. This trend reflects an increased accumulation of fine-grained fluvial sediments near the turbidity maximum, similar to that found in nearby Chesapeake Bay. The present annual accumulation of mud is about 1.54 million metric tons; the cumulative mass is 406 million metric tons.

Maryl↗

USGS2017

100,000-year-long terrestrial record of millennial-scale linkage between eastern North American mid-latitude paleovegetation shifts and Greenland ice-core oxygen isotope trends

We document frequent, rapid, strong, millennial-scale paleovegetation shifts throughout the late Pleistocene, within a 100,000+ yr interval (~ 115–15 ka) of terrestrial sediments from the mid-Atlantic Region (MAR) of North America. High-resolution analyses of fossil pollen from one core locality revealed a continuously shifting sequence of thermally dependent forest assemblages, ranging between two endmembers: subtropical oak-tupelo-bald cypress-gum forest and high boreal spruce-pine forest. Sedimentary textural evidence indicates fluvial, paludal, and loess deposition, and paleosol formation, representing sequential freshwater to subaerial environments in which this record was deposited. Its total age"depth model, based on radiocarbon and optically stimulated luminescence ages, ranges from terrestrial oxygen isotope stages (OIS) 6 to 1. The particular core sub-interval presented here is correlative in trend and timing to that portion of the oxygen isotope sequence common among several Greenland ice cores: interstades GI2 to GI24 (≈ OIS2–5 d). This site thus provides the first evidence for an essentially complete series of "Dansgaard"Oeschger" climate events in the MAR. These data reveal that the ~ 100,000 yr preceding the Late Glacial and Holocene in the MAR of North America were characterized by frequently and dynamically changing climate states, and by vegetation shifts that closely tracked the Greenland paleoclimate sequence.

Quaternary Research↗

USGS2006

Hydrogeologic framework of sedimentary deposits in six structural basins, Yakima River basin, Washington

The hydrogeologic framework was delineated for the ground-water flow system of the sedimentary deposits in six structural basins in the Yakima River Basin, Washington. The six basins delineated, from north to south are: Roslyn, Kittitas, Selah, Yakima, Toppenish, and Benton. Extent and thicknesses of the hydrogeologic units and total basin sediment thickness were mapped for each basin. Interpretations were based on information from about 4,700 well records using geochemical, geophysical, geologist's or driller's logs, and from the surficial geology and previously constructed maps and well interpretations. The sedimentary deposits were thickest in the Kittitas Basin reaching a depth of greater than 2,000 ft, followed by successively thinner sedimentary deposits in the Selah basin with about 1,900 ft, Yakima Basin with about 1,800 ft, Toppenish Basin with about 1,200 ft, Benton basin with about 870 ft and Roslyn Basin with about 700 ft.

Scientific Investigations Report↗

USGS2015

The Palos Verdes Fault offshore southern California: late Pleistocene to present tectonic geomorphology, seascape evolution and slip rate estimate based on AUV and ROV surveys

The Palos Verdes Fault (PVF) is one of few active faults in Southern California that crosses the shoreline and can be studied using both terrestrial and subaqueous methodologies. To characterize the near-seafloor fault morphology, tectonic influences on continental slope sedimentary processes and late Pleistocene to present slip rate, a grid of high-resolution multibeam bathymetric data, and chirp subbottom profiles were acquired with an autonomous underwater vehicle (AUV) along the main trace of PVF in water depths between 250 and 600 m. Radiocarbon dates were obtained from vibracores collected using a remotely operated vehicle (ROV) and ship-based gravity cores. The PVF is expressed as a well-defined seafloor lineation marked by subtle along-strike bends. Right-stepping transtensional bends exert first-order control on sediment flow dynamics and the spatial distribution of Holocene depocenters; deformed strata within a small pull-apart basin record punctuated growth faulting associated with at least three Holocene surface ruptures. An upper (shallower) landslide scarp, a buried sedimentary mound, and a deeper scarp have been right-laterally offset across the PVF by 55 ± 5, 52 ± 4 , and 39 ± 8 m, respectively. The ages of the upper scarp and buried mound are approximately 31 ka; the age of the deeper scarp is bracketed to 17–24 ka. These three piercing points bracket the late Pleistocene to present slip rate to 1.3–2.8 mm/yr and provide a best estimate of 1.6–1.9 mm/yr. The deformation observed along the PVF is characteristic of strike-slip faulting and accounts for 20–30% of the total right-lateral slip budget accommodated offshore Southern California.

California↗

USGS2021

Isolating detrital and diagenetic signals in magnetic susceptibility records from methane-bearing marine sediments

Volume-dependent magnetic susceptibility (κ) is commonly used for paleoenvironmental reconstructions in both terrestrial and marine sedimentary environments where it reflects a mixed signal between primary deposition and secondary diagenesis. In the marine environment, κ is strongly influenced by the abundance of ferrimagnetic minerals regulated by sediment transport processes. Post-depositional alteration by H 2 S, however, can dissolve titanomagnetite, releasing reactive Fe that promotes pyritization and subsequently decreases κ. Here, we provide a new approach for isolating the detrital signal in κ and identifying intervals of diagenetic alteration of κ driven by organoclastic sulfate reduction (OSR) and the anaerobic oxidation of methane (AOM) in methane-bearing marine sediments offshore India. Using the correlation of a heavy mineral proxy from X-ray fluorescence data (Zr/Rb) and κ in unaltered sediments, we predict the primary detrital κ signal and identify intervals of decreased κ, which correspond to increased total sulfur content. Our approach is a rapid, high-resolution method that can identify overprinted κ resulting from pyritization of titanomagnetite due to H 2 S production in marine sediments. In addition, total organic carbon, total sulfur, and authigenic carbonate δ 13 C measurements indicate that both OSR and AOM can drive the observed κ loss, but AOM drives the greatest decreases in κ. Overall, our approach can enhance paleoenvironmental reconstructions and provide insight into paleo-positions of the sulfate-methane transition zone, past enhancements of OSR or paleo-methane seepage, and the role of detrital iron oxide minerals on the marine sediment sulfur sink, with consequences influencing the development of chemosynthetic biological communities at methane seeps.

Geochemistry, Geophysics, Geosystems↗

USGS2012

A seismic refraction survey of the Imperial Valley Region, California

The U.S. Geological Survey conducted an extensive seismic refraction survey in the Imperial Valley region of California in 1979. The Imperial Valley is located in the Salton Trough, an active rift between the Pacific and North American plates. Forty shots fired at seven shot points were recorded by 100 portable seismic instruments at typical spacing of 0.5–1 km. More than 1300 recording locations were occupied, and more than 3000 usable seismograms were obtained. We analyzed five profiles using a standard ray‐tracing program, constructed a contour map of reduced travel times from our most widely recorded shot point, and modeled an existing gravity profile across the Salton Trough. Results are itemized: (1) All models have in common a sedimentary layer ( V p = 1.8–5.0 km/s), a “transition zone” ( V p = 5.0–5.65 km/s), a basement ( V p = 5.65 km/s in the Imperial Valley, 5.9 km/s on the bordering mesas), and subbasement ( V p = 7.2 km/s). (2) The sedimentary layer ranges in thickness along the axis of the Salton Trough from 3.7 km (Salton Sea) to 4.8 km (U.S.‐Mexican border). On the bordering mesas it is quite variable in thickness. (3) The “transition” zone is about 1 km thick in most places. In the Imperial Valley there are no marked velocity discontinuities in this zone between the sedimentary layer and basement. On the bordering mesas, however, there is a discontinuity at the top of this zone. (4) There are apparently two types of basement. On the bordering mesas, basement is crystalline igneous and metamorphic rocks. In the Imperial Valley, basement is mostly lower‐greenshist‐facies sedimentary rocks, based primarily on the smooth transition in character from sediment to basement arrivals, the low value of basement velocity, and the fact that deep (4 km) wells in the valley penetrate only the upper part of the known Cenozoic stratigraphic column for the Salton Trough. (5) The subbasement, or intermediate crustal layer, ranges in depth along the axis of the Salton Trough from 16 km (Salton Sea) to 10 km (U.S.‐Mexican border). Gravity modeling requires that this layer deepen and/or pinch out beneath the bordering mesas and mountain ranges. Based on its high velocity and the presence of intrusive basaltic rocks in the sedimentary section in the Imperial Valley, the subbasement is thought to be a mafic intrusive complex similar to oceanic middle crust. (6) Several structures are seen that affect basement, transition zone, and deeper parts of the sedimentary layer. They include a scarp along the Imperial fault, as much as 1 km down to the northeast, and a scarp passing roughly along the topographic boundary between the Imperial Valley and the bordering mesa to the west, as much as 3½ km down to the east. We interpret the latter scarp to be the suture, or rift boundary, between the older crystalline basement on the mesa and the younger metasedimentary basement in the Imperial Valley. (7) On a contour map of reduced travel time from our most widely recorded shot point, subtle patches of early arrivals among otherwise late arrivals in the central Imperial Valley correlate well with known geothermal resource areas having reservoir temperatures of more than 150°C. Apparently the Salton Trough is a location where new crust is being generated. As the rift opens, mafic intrusive rocks fill it from below as sedimentary rocks fill it from above. Rifting and intrusion produce high heat flow that metamorphoses the sedimentary rocks to shallow depth (metasedimentary basement in the Imperial Valley) and thus consolidates the new crust.

California↗

USGS2010

Correlation of aptian-albian carbon isotope excursions in continental strata of the cretaceous Foreland Basin, Eastern Utah, U.S.A.

Nodular carbonates ("calcretes") in continental foreland-basin strata of the Early Cretaceous Cedar Mountain Formation (CMF) in eastern Utah yield ??13C and ??O records of changes in the exogenic carbon cycle related to oceanic anoxic events (OAEs), and terrestrial paleoclimate. Chemostratigraphic profiles of both forebulge and foredeep sections show two prominent positive ??13C excursions, each with a peak value of -3% VPDB, and having background ??13C values of about -6% VPDB. These excursions correlate with the global early Aptian (Ap7) and late Aptian-early Albian (Apl2-All) carbon isotope excursions. Aptian-Albian positive ??13C excursions in the CMF also correspond to 3-4 per mil increases in carbonate ??18O. These phenomena record local aridification events. The chemostratigraphic profile on the thinner forebulge section of the CMF is calibrated, for the first time, by a radiogenic U-Pb date of 119.4 ?? 2.6 Ma on a carbonate bed, and by detrital zircon U-Pb dates on two bounding sandstone units (maximum depositional ages of 146 Ma and 112 Ma). P??trographie observations and diagenetic analyses of micritic to microsparitic carbonates from nodules indicate palustrine origins and demonstrate that they crystallized in shallow early meteoric phreatic environments. Meteoric calcite lines derived from CMF carbonates have ??18O values ranging between -8.1 to -7.5%o VPDB, supporting an estimate of zonal mean groundwater ??18O of -6% VSMOW for an Aptian-Albian paleolatitude of 34?? N. Furthermore, our two chemostratigraphic profiles exhibit a generally proportionate thinning of correlative strata from the foredeep on to the forebulge, suggesting that there were consistently lower rates of accumulation on the forebulge during the Aptian-Albian. Identification of the global Aptian-Albian ??13C excursions in purely continental strata, as demonstrated in this paper, opens a new avenue of research by identifying specific stratigraphie intervals that record the terrestrial paleoclimatic impacts of perturbations of the global carbon cycle. Copyright ?? 2010, SEPM (Society for Sedimentary Geology).

Journal of Sedimentary Research↗

USGS2015

Geologic and geophysical maps of the El Casco 7.5′ quadrangle, Riverside County, southern California, with accompanying geologic-map database

Introduction Earth materials and structures in the El Casco quadrangle provide considerable information about the late Cenozoic geologic evolution of southern California’s Inland Empire region (fig. 2). Important structural and stratigraphic elements include (1) modern traces of the right-lateral San Jacinto Fault zone, (2) older traces of the San Jacinto Fault zone, and (3) sedimentary materials and geologic structures that formed during the last eight million years or so and that record interactions within the San Andreas Fault system. These materials, and the structures that deform them, provide a geologic context 3 for investigations of groundwater recharge and subsurface flow (Waring, 1919; Burnham and Dutcher, 1960; Bloyd, 1971; Rewis and others, 2006). This geologic database of the El Casco 7.5′ quadrangle was prepared by the Basins and Landscape Co-Evolution Project (BALANCE), a regional geologic-mapping project sponsored jointly by the U.S. Geological Survey and the California Geological Survey. The database was developed as a contribution to the National Cooperative Geologic Mapping Program’s National Geologic Map Database, and provides a general geologic setting of the El Casco quadrangle. The database and map provide information about earth materials and geologic structures, including faults and folds that have developed in the quadrangle due to complexities in the San Andreas Fault system. Geologic information contained in the El Casco database is general-purpose data applicable to land-related investigations in the earth and biological sciences. The term “general-purpose” means that all geologic-feature classes have minimal information content adequate to characterize their general geologic characteristics and to interpret their general geologic history. However, no single feature class has enough information to definitively characterize its properties and origin. For this reason the database cannot be used for site-specific geologic evaluations, although it can be used to plan and guide investigations at the site-specific level.

California↗

USGS1972

Cenozoic rocks of the Santa Rita Mountains, southeast of Tucson, Arizona

The Santa Rita Mountains of southeastern Arizona are underlain, in part, by volcanic and sedimentary rocks and by many small intrusives, of Cenozoic age. These rocks provide a more complete geologic record than that of other ranges in the region, and consequently the Santa Rita Mountains are a useful reference area from which to develop the Cenozoic geologic history of the region. Many isotopic ages provide the basis for dating key units and add to the confidence in the interpretations of the geologic record of the rocks themselves. The rocks of the greatest potential economic interest are the Greaterville intrusives of the Helvetia and Greaterville mining districts and the quartz vein swarm of the Tyndall and Wrightson mining districts.

Arizona↗

USGS2025

Cyanotoxin production in shallow subtropical lakes is driven by nutrient enrichment and primary producer abundance on the millennial scale

Increased cyanotoxin concentrations from harmful algal blooms (HABs) in lake systems pose a global challenge to water quality. Although progress has been made in monitoring cyanotoxins in modern environments over recent decades, identifying the triggers of cyanotoxin release by cyanobacteria has yielded mixed results from experimental and analytical studies. Paleolimnological reconstructions can reveal whole-lake long-term changes, but few studies have directly measured cyanotoxins alongside other water quality proxies. Here, we investigated the drivers of sedimentary total microcystin (MC) concentrations on millennial scales in hypereutrophic Lakes Dora and Marian in central Florida, USA. We analyzed dated sediment records using paleolimnological techniques to reconstruct nutrient deposition, cyanobacteria abundance (photosynthetic pigments), and cyanotoxins (total MCs). The objective was to investigate the linkage between MC concentrations in the sediments with both biotic (cyanobacteria and other primary producers) and abiotic factors (nutrients and climate). We found that MC production occurred throughout the ∼7000-year period, progressing from periods of moderate to low, and then to high concentrations in both lakes. Statistical analyses showed that historical MC concentrations were correlated with sedimentary measurements of total phosphorus (TP), cyanobacteria abundance, and other primary producer groups, such as cryptophytes. However, there was only a minimal correspondence with climate proxies, such as charcoal and pollen, suggesting that internal nutrient cycling and human pressures were the dominant drivers of MC deposition. Our study demonstrates that cyanotoxins have occurred for millennia in both lakes with maintained relationships to nutrients and other environmental factors that existed both in historic and modern limnological conditions.

Florida↗

USGS2015

Coastal evidence for Holocene subduction-zone earthquakes and tsunamis in central Chile

The &sim;500-year historical record of seismicity along the central Chile coast (30–34°S) is characterized by a series of &sim;M 8.0–8.5 earthquakes followed by low tsunamis (<4 m) occurring on the megathrust about every 80 years. One exception is the AD 1730 great earthquake (M 9.0–9.5) and high tsunami (>10 m), but the frequency of such large events is unknown. We extend the seismic history of central Chile through a study of a lowland stratigraphic sequence along the metropolitan coast north of Valparaíso (33°S). At this site, higher relative sea level during the mid Holocene created a tidal marsh and the accommodation space necessary for sediment that preserves earthquake and tsunami evidence. Within this 2600-yr-long sequence, we traced six laterally continuous sand beds probably deposited by high tsunamis. Plant remains that underlie the sand beds were radiocarbon dated to 6200, 5600, 5000, 4400, 3800, and 3700 cal yr BP. Sediment properties and diatom assemblages of the sand beds—for example, anomalous marine planktonic diatoms and upward fining of silt-sized diatom valves—point to a marine sediment source and high-energy deposition. Grain-size analysis shows a strong similarity between inferred tsunami deposits and modern coastal sediment. Upward fining sequences characteristic of suspension deposition are present in five of the six sand beds. Despite the lack of significant lithologic changes between the sedimentary units under- and overlying tsunami deposits, we infer that the increase in freshwater siliceous microfossils in overlying units records coseismic uplift concurrent with the deposition of five of the sand beds. During our mid-Holocene window of evidence preservation, the mean recurrence interval of earthquakes and tsunamis is &sim;500 years. Our findings imply that the frequency of historical earthquakes in central Chile is not representative of the greatest earthquakes and tsunamis that the central Chilean subduction zone has produced.

Quaternary Science Reviews↗

USGS2017

Abundant carbon substrates drive extremely high sulfate reduction rates and methane fluxes in Prairie Pothole Wetlands

Inland waters are increasingly recognized as critical sites of methane emissions to the atmosphere, but the biogeochemical reactions driving such fluxes are less well understood. The Prairie Pothole Region (PPR) of North America is one of the largest wetland complexes in the world, containing millions of small, shallow wetlands. The sediment pore waters of PPR wetlands contain some of the highest concentrations of dissolved organic carbon (DOC) and sulfur species ever recorded in terrestrial aquatic environments. Using a suite of geochemical and microbiological analyses, we measured the impact of sedimentary carbon and sulfur transformations in these wetlands on methane fluxes to the atmosphere. This research represents the first study of coupled geochemistry and microbiology within the PPR and demonstrates how the conversion of abundant labile DOC pools into methane results in some of the highest fluxes of this greenhouse gas to the atmosphere ever reported. Abundant DOC and sulfate additionally supported some of the highest sulfate reduction rates ever measured in terrestrial aquatic environments, which we infer to account for a large fraction of carbon mineralization in this system. Methane accumulations in zones of active sulfate reduction may be due to either the transport of free methane gas from deeper locations or the co-occurrence of methanogenesis and sulfate reduction. If both respiratory processes are concurrent, any competitive inhibition of methanogenesis by sulfate-reducing bacteria may be lessened by the presence of large labile DOC pools that yield noncompetitive substrates such as methanol. Our results reveal some of the underlying mechanisms that make PPR wetlands biogeochemical hotspots, which ultimately leads to their critical, but poorly recognized role in regional greenhouse gas emissions.

North Dakota↗

USGS2000

Strong motion from surface waves in deep sedimentary basins

It is widely recognized that long-period surface waves generated by conversion of body waves at the boundaries of deep sedimentary basins make an important contribution to strong ground motion. The factors controlling the amplitude of such motion, however, are not widely understood. A study of pseudovelocity response spectra of strong-motion records from the Los Angeles Basin shows that late-arriving surface waves with group velocities of about 1 km/sec dominate the ground motion for periods of 3 sec and longer. The rate of amplitude decay for these waves is less than for the body waves and depends significantly on period, with smaller decay for longer periods. The amplitude can be modeled by the equation log y = f(M, RE) + c + bRB where y is the pseudovelocity response, f(M, RE) is an attenuation relation based on a general strong-motion data set, M is moment magnitude, RE is the distance from the source to the edge of the basin, RB is the distance from the edge of the basin to the recording site, and b and c are parameters fit to the data. The equation gives values larger by as much as a factor of 3 than given by the attenuation relationships based on general strong-motion data sets for the same source-site distance. It is clear that surface waves need to be taken into account in the design of long-period structures in deep sedimentary basins. The ground-motion levels specified by the earthquake provisions of current building codes, in California at least, accommodate the long-period ground motions from basin-edge-generated surface waves for periods of 5 sec and less and earthquakes with moment magnitudes of 7.5 or less located more than 20 km outside the basin. There may be problems at longer periods and for earthquakes located closer to the basin edge. The results of this study suggest that anelastic attenuation may need to be included in attempts to model long-period motion in deep sedimentary basins. To obtain better data on surface waves in the future, operators of strong-motion networks should take special care for the faithful recording of the long-period components of ground motion. It will also be necessary to insure that at least some selected recorders, once triggered, continue to operate for a time sufficient for the surface waves to traverse the basin. With velocities of about 1 km/sec, that time will be as long as 100 sec for a basin the size of the Los Angeles Basin.

Bulletin of the Seismological Society of America↗

USGS2008

Geologic map of the Denver West 30' x 60' quadrangle, north-central Colorado

The Denver West quadrangle extends east-west across the entire axis of the Front Range, one of numerous uplifts in the Rocky Mountain region in which Precambrian rocks are exposed. The history of the basement rocks in the Denver West quadrangle is as old as 1,790 Ma. Along the east side of the range, a sequence of sedimentary rocks as old as Pennsylvanian, but dominated by Cretaceous-age rocks, overlies these ancient basement rocks and was upturned and locally faulted during Laramide (Late Cretaceous to early Tertiary) uplift of the range. The increasingly coarser grained sediments up section in rocks of latest Cretaceous to early Tertiary age record in remarkable detail this Laramide period of mountain building. On the west side of the range, a major Laramide fault (Williams Range thrust) places Precambrian rocks over Cretaceous sedimentary rocks. The geologic history of the quadrangle, therefore, can be divided into four major periods: (1) Proterozoic history, (2) Pennsylvanian to pre-Laramide, Late Cretaceous history, (3) Late Cretaceous to early Tertiary Laramide mountain building, and (4) post-Laramide history. In particular, the Quaternary history of the Denver West quadrangle is described in detail, based largely on extensive new mapping.

Scientific Investigations Map↗

USGS2021

A rock record of complex aeolian bedforms in a Hesperian desert landscape: The Stimson formation as exposed in the Murray Buttes, Gale Crater, Mars

Lithified aeolian strata encode information about ancient planetary surface processes and the climate during deposition. Decoding these strata provides insight regarding past sediment transport processes, bedform kinematics, depositional landscape, and the prevailing climate. Deciphering these signatures requires a detailed analysis of sedimentary architecture to reconstruct dune morphology, motion, and the conditions that enabled their formation. Here, we show that a distinct sandstone unit exposed in the foothills of Mount Sharp, Gale crater, Mars, records the preserved expression of compound aeolian bedforms that accumulated in a large dune field. Analysis of Mastcam images of the Stimson formation shows that it consists of cross‐stratified sandstone beds separated by a hierarchy of erosive bounding surfaces formed during dune migration. The presence of two orders of surfaces with distinct geometrical relations reveals that the Stimson‐era landscape consisted of large dunes (draas) with smaller, superimposed dunes migrating across their lee slopes. Analysis of cross‐lamination and subset bounding surface geometries indicate a complex wind regime that transported sediment toward the north, constructing oblique dunes. This dune field was a direct product of the regional climate and the surface processes active in Gale crater during the fraction of the Hesperian Period recorded by the Stimson formation. The environment was arid, supporting a large aeolian dune field; this setting contrasts with earlier humid depositional episodes, recorded by the lacustrine sediments of the Murray formation (also Hesperian). Such fine‐scale reconstruction of landscapes on the ancient surface of Mars is important to understanding the planet’s past climate and habitability.

Journal of Geophysical Research - Planets↗