SEARCH · Search USGS

Results for “Geological Journal”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16Linked to original sources

USGS2016

Hydrogeochemistry and coal-associated bacterial populations from a methanogenic coal bed

Biogenic coalbed methane (CBM), a microbially-generated source of natural gas trapped within coal beds, is an important energy resource in many countries. Specific bacterial populations and enzymes involved in coal degradation, the potential rate-limiting step of CBM formation, are relatively unknown. The U.S. Geological Survey (USGS) has established a field site, (Birney test site), in an undeveloped area of the Powder River Basin (PRB), with four wells completed in the Flowers-Goodale coal bed, one in the overlying sandstone formation, and four in overlying and underlying coal beds (Knoblach, Nance, and Terret). The nine wells were positioned to characterize the hydraulic conductivity of the Flowers-Goodale coal bed and were selectively cored to investigate the hydrogeochemistry and microbiology associated with CBM production at the Birney test site. Aquifer-test results indicated the Flowers-Goodale coal bed, in a zone from about 112 to 120 m below land surface at the test site, had very low hydraulic conductivity (0.005 m/d) compared to other PRB coal beds examined. Consistent with microbial methanogenesis, groundwater in the coal bed and overlying sandstone contain dissolved methane (46 mg/L average) with low δ 13 C values (−67&permil; average), high alkalinity values (22 meq/kg average), relatively positive δ 13 C-DIC values (4&permil; average), and no detectable higher chain hydrocarbons, NO 3 − , or SO 4 2− . Bioassay methane production was greatest at the upper interface of the Flowers-Goodale coal bed near the overlying sandstone. Pyrotag analysis identified Aeribacillus as a dominant in situ bacterial community member in the coal near the sandstone and statistical analysis indicated Actinobacteria predominated coal core samples compared to claystone or sandstone cores. These bacteria, which previously have been correlated with hydrocarbon-containing environments such as oil reservoirs, have demonstrated the ability to produce biosurfactants to break down hydrocarbons. Identifying microorganisms involved in coal degradation and the hydrogeochemical conditions that promote their activity is crucial to understanding and improving in situ CBM production.

Montana, Wyoming↗

USGS2008

Biogenic origin of coalbed gas in the northern Gulf of Mexico Coastal Plain, U.S.A

New coal-gas exploration and production in northern Louisiana and south-central Mississippi, Gulf of Mexico Basin, is focused on the Wilcox Group (Paleocene–Eocene), where the depth to targeted subbituminous C to high volatile C bituminous coal beds ranges from 300 to 1680 m, and individual coal beds have a maximum thickness of about 6 m. Total gas content (generally excluding residual gas) of the coal beds ranges from less than 0.37 cm 3 /g (as-analyzed or raw basis; 1.2 cm 3 /g, dry, ash free basis, daf) at depths less than 400 m, to greater than 7.3 cm 3 /g (as-analyzed basis; 8.76 cm 3 /g, daf) in deeper (> 1,500 m) parts of the basin. About 20 Wilcox coal-gas wells in northern Louisiana produce from 200 to 6485 m 3 of gas/day and cumulative gas production from these wells is approximately 25 million m 3 (as of December, 2006). U.S. Geological Survey assessment of undiscovered, technically recoverable gas resources in the Gulf of Mexico Coastal Plain, including northern and south-central Mississippi, indicates that coal beds of the Wilcox Group contain an estimated mean total 109.3 million m 3 (3.86 trillion ft 3 ) of producible natural gas. To determine the origin of the Wilcox Group coal gases in northern Louisiana, samples of gas, water, and oil were collected from Wilcox coal and sandstone reservoirs and from under- and overlying Late Cretaceous and Eocene carbonate and sandstone reservoirs. Isotopic data from Wilcox coal-gas samples have an average δ 13 C CH4 value of − 62.6‰ VPDB (relative to Vienna Peedee Belemnite) and an average δ D CH4 value of − 199.9‰ VSMOW (relative to Vienna Standard Mean Ocean Water). Values of δ 13 C CO2 range from − 25.4 to 3.42‰ VPDB. Produced Wilcox saline water collected from oil, conventional gas, and coalbed gas wells have δ D H2O values that range from − 27.3 to − 18.0‰ VSMOW. These data suggest that the coal gases primarily are generated in saline formation water by bacterial reduction of CO 2 . Shallow (< 150 m) Wilcox coal beds containing freshwater have little or no biogenic gas. Molecular and isotopic analyses of gas samples collected from conventional gas and oil wells suggests that both biogenic and thermogenic gases are present in and adjacent to the Wilcox intervals that contain biogenic coal gases. Oil, probably sourced from thermally mature, down-structural-dip parts of the Wilcox Group, is produced from sandstones within the coal-bearing interval. Gas chromatograms of C 10+ saturated hydrocarbons from Wilcox oils show a depletion of n -alkanes probably resulting from biodegradation of the oil. Isotopic composition of the gases associated with the oils is of mixed themogenic and biogenic origin (average δ 13 C CH4 = − 44.4‰ VPDB, and average δ D CH4 = − 182.4‰ VSMOW).

International Journal of Coal Geology↗

USGS2012

Geostatistical modeling of the gas emission zone and its in-place gas content for Pittsburgh-seam mines using sequential Gaussian simulation

Determination of the size of the gas emission zone, the locations of gas sources within, and especially the amount of gas retained in those zones is one of the most important steps for designing a successful methane control strategy and an efficient ventilation system in longwall coal mining. The formation of the gas emission zone and the potential amount of gas-in-place (GIP) that might be available for migration into a mine are factors of local geology and rock properties that usually show spatial variability in continuity and may also show geometric anisotropy . Geostatistical methods are used here for modeling and prediction of gas amounts and for assessing their associated uncertainty in gas emission zones of longwall mines for methane control. This study used core data obtained from 276 vertical exploration boreholes drilled from the surface to the bottom of the Pittsburgh coal seam in a mining district in the Northern Appalachian basin. After identifying important coal and non-coal layers for the gas emission zone, univariate statistical and semivariogram analyses were conducted for data from different formations to define the distribution and continuity of various attributes. Sequential simulations performed stochastic assessment of these attributes, such as gas content, strata thickness, and strata displacement. These analyses were followed by calculations of gas-in-place and their uncertainties in the Pittsburgh seam caved zone and fractured zone of longwall mines in this mining district. Grid blanking was used to isolate the volume over the actual panels from the entire modeled district and to calculate gas amounts that were directly related to the emissions in longwall mines. Results indicated that gas-in-place in the Pittsburgh seam, in the caved zone and in the fractured zone, as well as displacements in major rock units, showed spatial correlations that could be modeled and estimated using geostatistical methods. This study showed that GIP volumes may change up to 3 MMscf per acre and, in a multi-panel district, may total 9 Bcf of methane within the gas emission zone. Therefore, ventilation and gas capture systems should be designed accordingly. In addition, rock displacements within the gas emission zone are spatially distributed. From an engineering and practical point of view, spatial distributions of GIP and distributions of rock displacements should be correlated with in-mine emissions and gob gas venthole productions.

International Journal of Coal Geology↗

USGS2009

The timing of eclogite facies metamorphism and migmatization in the Orlica–Śnieżnik complex, Bohemian Massif: Constraints from a multimethod geochronological study

The Orlica–Śnieżnik complex (OSC) is a key geological element of the eastern Variscides and mainly consists of amphibolite facies orthogneisses and metasedimentary rocks. Sporadic occurrences of eclogites and granulites record high-pressure (HP) to ultrahigh-pressure (UHP) metamorphic conditions. A multimethod geochronological approach ( 40 Ar– 39 Ar, Rb–Sr, Sm–Nd, U–Pb) has been used to gain further insights into the polymetamorphic evolution of eclogites and associated country rocks. Special attention was given to the unresolved significance of a 370- to 360 Ma age group that was repeatedly described in previous studies. Efforts to verify the accuracy of c. 370 Ma K–Ar phengite and biotite dates reported for an eclogite and associated country-rock gneiss from the location Nowa Wieś suggest that these dates are meaningless, due to contamination with extraneous Ar. Extraneous Ar is also considered to be responsible for a significantly older 40 Ar– 39 Ar phengite date of c. 455 Ma for an eclogite from the location Wojtowka. Attempts to further substantiate the importance of 370–360 Ma zircon dates as an indicator for a melt-forming high-temperature (HT) episode did not provide evidence in support of anatectic processes at this time. Instead, SHRIMP U–Pb zircon dating of leucosomes and leucocratic veins within both orthogneisses and (U)HP granulites revealed two age populations (490–450 and 345–330 Ma respectively) that correspond to protolith ages of the magmatic precursors and late Variscan anatexis. The results of this study further underline the importance of Late Carboniferous metamorphic processes for the evolution of the OSC that comprise the waning stages of HP metamorphism and lower pressure HT overprinting with partial melting. Eclogites and their country rocks provided no chronometric evidence for an UHP and ultrahigh-temperature episode at 387–360 Ma, as recently suggested for granulites from the OSC, based on Lu–Hf garnet ages ( Anczkiewicz et al. , 2007 ).

Orlica-Snieznik complex↗

USGS2020

Sample mounting for organic petrology: No thermal effects from transient exposure to elevated temperatures

For sample mounting, organic petrology laboratories typically use cold-setting epoxy-resin (e.g., 40 °C, used by Oklahoma Geological Survey, OGS) or heat-setting thermoplastic (e.g., 180 °C, used by U.S. Geological Survey, USGS). Previous workers have suggested a systematic huminite/vitrinite reflectance (VR o ) increase was associated with the thermoplastic preparation process, relative to epoxy mounting, which was possibly attributed to moisture loss from organic matter due to the transient high temperatures of plastic mounting. In this study, we evaluated thermal effects to low thermal maturity organic matter from transient exposure to elevated temperatures. A subbituminous coal sample was subjected to long-term (4 to 38 weeks) exposure to temperatures of 85 to 120 °C and afterward evaluated by multiple approaches to test thermal advance [elemental analyses, Rock-Eval pyrolysis, Fourier transform infrared spectroscopy (FTIR), nuclear magnetic resonance (NMR), pyrolysis gas chromatography, and petrographic analyses, including huminite/vitrinite reflectance and spectral fluorescence], all of which showed no detectable systematic (statistically insignificant) changes between the original sample and its heat-treated products. We also compared huminite/vitrinite reflectance of six low thermal maturity samples (those most likely to react to transient heating) mounted via both cold-setting epoxy-resin and heat-setting thermoplastic. Results indicate measured VR o of a sample prepared by one mounting process was within the standard deviation of reflectance for the same sample prepared via the other process. Moreover, VR o results were not systematically higher in thermoplastic mounts. Contrary to previous work, these results suggest thermoplastic mounting or other transient exposure to elevated temperatures does not impact thermal maturity estimates from reflectance measurement for low thermal maturity organic samples. Furthermore, the average interlaboratory difference in measured VR o (between OGS and USGS) for the same sample prepared by either epoxy-resin or thermoplastic mounting was 0.038%, about double the average difference between VR o for the same sample prepared via epoxy-resin versus thermoplastic in a single laboratory (0.024%). This result indicates interlaboratory variability impacts VR o measurement reproducibility to the extent that systematic differences could not be observed between thermoplastic and cold-setting sample preparation approaches, even if such differences were present.

International Journal of Coal Geology↗

USGS2012

Minor element distribution in iron disulfides in coal: a geochemical review

Electron beam microanalysis of coal samples in U.S. Geological Survey (USGS) labs confirms that As is the most abundant minor constituent in Fe disulfides in coal and that Se, Ni, and other minor constituents are present less commonly and at lower concentrations than those for As. In nearly all cases, Hg occurs in Fe disulfides in coal at concentrations below detection by electron beam instruments. Its presence is shown by laser ablation ICP-MS, by selective leaching studies of bulk coal, and by correlation with Fe disulfide proxies such as total Fe and pyritic sulfur. Multiple generations of Fe disulfides are present in coal. These commonly show grain-to-grain and within-grain minor- or trace element compositional variation that is a function of the early diagenetic, coalification, and post-coalification history of the coal. Framboidal pyrite is almost always the earliest Fe disulfide generation, as shown by overgrowths of later Fe disulfides which may include pyrite or marcasite. Cleat- (or vein) pyrite (or marcasite) is typically the latest Fe disulfide generation, as shown by cross-cutting relations. Cleat pyrite forms by fluid migration within a coal basin and consequently may be enriched in elements such as As by deposition from compaction-driven fluids, metal enriched basinal brines or hydrothermal fluids. In some cases, framboidal pyrite shows preferential Ni enrichment with respect to co-occurring pyrite forms. This is consistent with bacterial complexing of metals in anoxic sediments and derivation of framboidal pyrite from greigite (Fe 3 S 4 ), an Fe monosulfide precursor to framboidal pyrite having the thio-spinel structure which accommodates transition metals. Elements such as As, Se, and Sb substitute for S in the pyrite structure whereas metals, including transition metals, Hg and Pb, are thought to substitute for Fe. Understanding the distribution of minor and trace elements in Fe disulfides in coal has important implications for their availability to the environment through coal mining and use, as well as for potential reduction by coal preparation, and for delineating diagenetic compositional changes throughout and after coal formation.

International Journal of Coal Geology↗

USGS2007

Cleats and their relation to geologic lineaments and coalbed methane potential in Pennsylvanian coals in Indiana

Cleats and fractures in Pennsylvanian coals in southwestern Indiana were described, statistically analyzed, and subsequently interpreted in terms of their origin, relation to geologic lineaments, and significance for coal permeability and coalbed gas generation and storage. These cleats can be interpreted as the result of superimposed endogenic and exogenic processes. Endogenic processes are associated with coalification (i.e., matrix dehydration and shrinkage), while exogenic processes are mainly associated with larger-scale phenomena, such as tectonic stress. At least two distinct generations of cleats were identified on the basis of field reconnaissance and microscopic study: a first generation of cleats that developed early on during coalification and a second generation that cuts through the previous one at an angle that mimics the orientation of the present-day stress field. The observed parallelism between early-formed cleats and mapped lineaments suggests a well-established tectonic control during early cleat formation. Authigenic minerals filling early cleats represent the vestiges of once open hydrologic regimes. The second generation of cleats is characterized by less prominent features (i.e., smaller apertures) with a much less pronounced occurrence of authigenic mineralization. Our findings suggest a multistage development of cleats that resulted from tectonic stress regimes that changed orientation during coalification and basin evolution. The coals studied are characterized by a macrocleat distribution similar to that of well-developed coalbed methane basins (e.g., Black Warrior Basin, Alabama). Scatter plots and regression analyses of meso- and microcleats reveal a power-law distribution between spacing and cleat aperture. The same distribution was observed for fractures at microscopic scale. Our observations suggest that microcleats enhance permeability by providing additional paths for migration of gas out of the coal matrix, in addition to providing access for methanogenic bacteria. The abundance, distribution, and orientation of cleats control coal fabric and are crucial features in all stages of coalbed gas operations (i.e., exploration and production). Understanding coal fabric is important for coal gas exploration as it may be related to groundwater migration and the occurrence of methanogenic bacteria, prerequisite to biogenic gas accumulations. Likewise, the distribution of cleats in coal also determines pathways for migration and accumulation of thermogenic gas generated during coalification. ?? 2007 Elsevier B.V. All rights reserved.

International Journal of Coal Geology↗

USGS2022

Flood lavas on Earth, Io and Mars

Flood lavas are major geological features on all the major rocky planetary bodies. They provide important insight into the dynamics and chemistry of the interior of these bodies. On the Earth, they appear to be associated with major and mass extinction events. It is therefore not surprising that there has been significant research on flood lavas in recent years. Initial models suggested eruption durations of days and volumetric fluxes of order 10 7 m 3 s −1 with flows moving as turbulent floods. However, our understanding of how lava flows can be emplaced under an insulating crust was revolutionized by the observations of actively inflating pahoehoe flows in Hawaii. These new ideas led to the hypothesis that flood lavas were emplaced over many years with eruption rates of the order of 10 4 m 3 s −1 . The field evidence indicates that flood lava flows in the Columbia River Basalts, Deccan Traps, Etendeka lavas, and the Kerguelen Plateau were emplaced as inflated pahoehoe sheet flows. This was reinforced by the observation of active lava flows of ≥100 km length on Io being formed as tube-fed flows fed by moderate eruption rates (10 2 –10 3 m 3 s −1 ). More recently it has been found that some flood lavas are also emplaced in a more rapid manner. New high-resolution images from Mars revealed ‘platy–ridged’ flood lava flows, named after the large rafted plates and ridges formed by compression of the flow top. A search for appropriate terrestrial analogues found an excellent example in Iceland: the 1783–1784 Laki Flow Field. The brecciated Laki flow top consists of pieces of pahoehoe, not aa clinker, leading us to call this ‘rubbly pahoehoe’. Similar flows have been found in the Columbia River Basalts and the Kerguelen Plateau. We hypothesize that these flows form with a thick, insulating, but mobile crust, which is disrupted when surges in the erupted flux are too large to maintain the normal pahoehoe mode of emplacement. Flood lavas emplaced in this manner could have (intermittently) reached effusion rates of the order of 10 6 m 3 s −1 .

Journal of the Geological Society↗

USGS1993

Coal resources of the Sonda coal field, Sindh Province, Pakistan

Approximately 4.7 billion t of original coal resources, ranging from lignite A to subbituminous C in rank, are estimated to be present in the Sonda coal field. These resources occur in 10 coal zones in the Bara Formation of Paleocene age. The Bara Formation does not out crop in the area covered by this report. Thin discontinuous coal beds also occur in the Sonhari Member of the Laki Formation, of Paleocene and Eocene age, but they are unimportant as a resource of the Sonda coal field. The coal resource assessment was based on 56 exploratory drill holes that were completed in the Sonda field between April 1986 and February 1988. The Sonda coal field is split into two, roughly equal, areas by the southwestward flowing Indus River, a major barrier to the logistics of communications between the two halves. As a result the two halves, called the Sonda East and Sonda West areas, were evaluated at different times by slightlydifferent techniques; but, because the geology is consistent between the two areas, the results of both evaluations have been summarized in this report. The resource estimates for the Sonda East area, approximately 1,700 million t, were based on the thickest coal bed in each zone at each drill hole. This method gives a conservative estimate of the total amount of coal in the Sonda East area. The resource estimates for the Sonda West area, approximately 3,000 million t, were based on cumulative coal bed thicknesses within each coal zone, resulting in a more liberal estimate. In both cases, minimum parameters for qualifying coal were a thickness of 30 cm or greater and no more than 50% ash; partings thicker than 1 cm were excluded. The three most important coal zones in the Sonda field are the Inayatabad, the Middle Sonda and the Lower Sonda. Together, these three coal zones contain 50% of the total resources. Isopachs were constructed for the thickest coal beds in these three coal zones and indicate large variations in thickness over relatively small distances. Coal beds in the Sonda coal field were difficult to correlate because of poor core recovery in some intervals and abrupt lateral thinning and thickening. Most coal zones are separated by 5–10 m of interburden, although in some places the interburden between zones is over 100 m thick. More closely spaced drill holes should clarify and significantly improve coal zone correlations in the Bara Formation. Coal resources in the Sonda coal field were calculated for three reliability categories; measured, indicated, and inferred. The most reliable estimates are those for the measured category. Measured coal resources are approximately 91 million t, or about 2% of the total resource; indicated resources are 681 million t, or about 14% of the total; and inferred resources, the least reliable resource category, are 3,931 million t, or 84% of the total resources. The distribution of resources by reliability category is due to the relatively wide spacing (approximately 5 km) between core holes. Analyses of 90 coal samples, on an as-received basis, indicate average ash and sulfur contents of 13.7% and 3.6%, respectively, and a range in rank from lignite A to subbituminous C. Calorific values for these samples range from 6,000 to 8,000 Btu/lb (1 Btu = 1055J; 1 lb = 4536 kg).

International Journal of Coal Geology↗

USGS2008

Progression in sulfur isotopic compositions from coal to fly ash: Examples from single-source combustion in Indiana

Sulfur occurs in multiple mineral forms in coals, and its fate in coal combustion is still not well understood. The sulfur isotopic composition of coal from two coal mines in Indiana and fly ash from two power plants that use these coals were studied using geological and geochemical methods. The two coal beds are Middle Pennsylvanian in age; one seam is the low-sulfur (< 1%) Danville Coal Member of the Dugger Formation and the other is the high-sulfur (> 5%) Springfield Coal Member of the Petersburg Formation. Both seams have ash contents of approximately 11%. Fly-ash samples were collected at various points in the ash-collection system in the two plants. The results show notable difference in ??34S for sulfur species within and between the low-sulfur and high-sulfur coal. The ??34S values for all sulfur species are exclusively positive in the low-sulfur Danville coal, whereas the ??34S values for sulfate, pyritic, and organic sulfur are both positive and negative in the high-sulfur Springfield coal. Each coal exhibits a distinct pattern of stratigraphic variation in sulfur isotopic composition. Overall, the ??34S for sulfur species values increase up the section in the low-sulfur Danville coal, whereas they show a decrease up the vertical section in the high-sulfur Springfield coal. Based on the evolution of ??34S for sulfur species, it is suggested that there was influence of seawater on peat swamp, with two marine incursions occurring during peat accumulation of the high-sulfur Springfield coal. Therefore, bacterial sulfate reduction played a key role in converting sulfate into hydrogen sulfide, sulfide minerals, and elemental sulfur. The differences in ??34S between sulfate sulfur and pyritic sulfur is very small between individual benches of both coals, implying that some oxidation occurred during deposition or postdeposition. The ??34S values for fly ash from the high-sulfur Springfield coal (averaging 9.7???) are greatly enriched in 34S relative to those in the parent coal (averaging 2.2???). This indicates a fractionation of sulfur isotopes during high-sulfur coal combustion. By contrast, the ??34S values for fly-ash samples from the low-sulfur Danville coal average 10.2???, only slightly enriched in 34S relative to those from the parent coal (average 7.5???). The ??34S values for bulk S determined directly from the fly-ash samples show close correspondence with the ??34S values for SO4- 2 leached from the fly ash in the low-sulfur coal, suggesting that the transition from pyrite to sulfate occurred via high-temperature oxidation during coal combustion. ?? 2007 Elsevier B.V. All rights reserved.

International Journal of Coal Geology↗

USGS2024

Novel insights about petroleum systems from source and reservoir rock characterization, Cretaceous Deposits, Babouri-Figuil Basin, Northern Cameroon

The Babouri-Figuil Basin (BFB) is a frontier basin for petroleum in Cameroon. It belongs to the series of Cretaceous rift basins of the West and Central Rift System (WCARS), the origin of which is related to the opening of the South Atlantic. Within the same rift system, commercial hydrocarbon accumulations have been discovered in Chad, Sudan, Niger and, more recently, in Nigeria (Gongola Basin). The study of the geology of the BFB just recently received considerable attention, mainly because of its presumed hydrocarbon potential. In the pursuit of researching possible petroleum systems in the BFB, the current study provides a first look into the characterization of source and reservoir rock and its integration into a 2D lithostratigraphic model. The study was solely based on outcrop samples. Black shale and massive claystone are good to excellent hydrocarbon source rocks [e.g., up to 38 wt% total organic carbon (TOC), up to 943 mg/g hydrogen index, up to 85 m thickness, up to 20–30 km lateral extension], with moderate to high values of extractable organic matter (e.g., >10,000 ppm). Calcareous claystone, on the other hand, are poor source rocks [e.g., <0.20 wt% TOC]. The samples are thermally immature, except for those located close to volcanic intrusion at Golombe that have reached the threshold for oil generation (Tmax >435 °C, production index >0.1). The petrographic analysis of sandstone revealed that they are fine-grained to coarse-grained, poorly to moderately sorted, texturally and compositionally immature to submature, subarkosic to arkosic arenites. The main diagenetic processes that affected sandstones are as follows: moderate to intense compaction characterized by the development of long, concavo-convex, and sutured contacts between grains; cementation through calcite, iron oxide, and quartz cements; alteration of mica and feldspar grains; partial to complete dissolution of feldspar, mica, amphibole grains, and calcite cement; and the replacement of feldspar and mica grains by clay minerals. Alteration and dissolution increase the porosity of sandstone through the creation of secondary pores. However, mechanical compaction through the development of a pseudomatrix and cementation as pore-filling materials have significantly reduced the quality of sandstone beds as conventional petroleum reservoirs. Hence, the best reservoir-quality sandstones in the basin are generally located in the upper portion of the basin in terms of its lithostratigraphic model. They are the cleanest sandstones with the smallest amount of cement and the lowest ductile grain content (pseudomatrix), with a thickness that varies from 3 m to 120 m and a lateral extension of 20 km. The lithostratigraphic model of the basin is characterized by an extensive lacustrine environment that provided a thick sequence of organic-rich formations; sand deposited as extensive reservoirs sandwiched between shale/claystone beds; the development of stratigraphic traps through lateral facies change; and the widespread deposition of lacustrine and floodplain claystone that provide regional seals. The similarities between the Babouri-Figuil Basin and proven petroleum systems in other WCARS rift basins suggest that the basin may host at least one petroleum system where actively generating source rocks are present.

Babouri-Figuil Basin↗

USGS2014

Petrographic maturity parameters of a Devonian shale maturation series, Appalachian Basin, USA. ICCP Thermal Indices Working Group interlaboratory exercise

This paper presents results of an interlaboratory exercise on organic matter optical maturity parameters using a natural maturation series comprised by three Devonian shale samples (Huron Member, Ohio Shale) from the Appalachian Basin, USA. This work was conducted by the Thermal Indices Working Group of the International Committee for Coal and Organic Petrology (ICCP) Commission II (Geological Applications of Organic Petrology). This study aimed to compare: 1. maturation predicted by different types of petrographic parameters (vitrinite reflectance and spectral fluorescence of telalginite), 2. reproducibility of the results for these maturation parameters obtained by different laboratories, and 3. improvements in the spectral fluorescence measurement obtained using modern detection systems in comparison with the results from historical round robin exercises. Mean random vitrinite reflectance measurements presented the highest level of reproducibility (group standard deviation 0.05) for low maturity and reproducibility diminished with increasing maturation (group standard deviation 0.12). Corrected fluorescence spectra, provided by 14 participants, showed a fair to good correspondence. Standard deviation of the mean values for spectral parameters was lowest for the low maturity sample but was also fairly low for higher maturity samples. A significant improvement in the reproducibility of corrected spectral fluorescence curves was obtained in the current exercise compared to a previous investigation of Toarcian organic matter spectra in a maturation series from the Paris Basin. This improvement is demonstrated by lower values of standard deviation and is interpreted to reflect better performance of newer photo-optical measuring systems. Fluorescence parameters measured here are in good agreement with vitrinite reflectance values for the least mature shale but indicate higher maturity than shown by vitrinite reflectance for the two more mature shales. This red shift in λ max beyond 0.65% vitrinite reflectance was also observed in studies of Devonian shale in other basins, suggesting that the accepted correlation for these two petrographic thermal maturity parameters needs to be re-evaluated. A good linear correlation between λ max and T max for this maturation series was observed and λ max 600 nm corresponds to T max of 440 °C. Nevertheless if a larger set of Devonian samples is included, the correlation is polynomial with a jump in λ max ranging from 540 to 570 nm. Up to 440 °C of T max , the λ max , mostly, reaches up to 500 nm; beyond a T max of 440 °C, λ max is in the range of 580–600 nm. This relationship places the “red shift” when the onset of the oil window is reached at T max of 440 °C. Moreover, the correlation between HI and λ max (r 2 = 0.70) shows a striking inflection and decrease in HI above a λ max of 600 nm, coincident with the approximate onset of hydrocarbon generation in these rocks.

International Journal of Coal Geology↗

USGS1989

The geology, botany and chemistry of selected peat-forming environments from temperate and tropical latitudes

Peat has been studied in several geologic settings: (1) glaciated terrain in cold temperate Maine and Minnesota, U.S.A.; (2) an island in the Atlantic Ocean off the coast of Maine, where sea level is rising; (3) the warm temperate U.S. Atlantic and Gulf Coastal Plains, where sea level has changed often; and (4) the tropical coast of Sarawak, Malaysia, and the tropical delta of the Batang Hari River, Sumatra, Indonesia. Most of these deposits are domed (ombrotrophic or partly ombrotrophic) bogs in which peat accumulation continued above the surface of the surrounding soil. However, the bogs of the U.S. Atlantic and Gulf Coastal Plains are comparatively not as domed, and many have almost level surfaces. In some bogs, aquatic or semi-aquatic plant materials accumulated, replaced water in the depressions, and formed a surface on which marsh or swamp vegetation could subsequently live, die, and accumulate. In others, the plant materials accumulated initially on level silt or sand surfaces supporting marshes or swamps. As the peat dome formed, plants growing on it changed from luxuriant ones near the base of the dome, where nutrients were brought into the bog by surface and ground water, to stunted ones at the top of the dome, where the raised bogs are fed by nutrient-poor precipitation. The physical and chemical changes that take place in the sequence of environments from the pond stage of deposit development, through the grassy marsh stage, through the forested swamp stage, and finally through the heath dome stage can be measured in terms of acidity and ash, volatile matter, carbon, hydrogen, nitrogen, sulfur and oxygen contents, as well as in the kind and distribution of trace elements. The organic and inorganic contents of the deposits relate to geomorphology, and geomorphology relates to their settings. As models of coal formation, some domed peat deposits may help in solving problems of distribution and character of ancient coal beds. But clearly not all peat deposits are precursors of coal. Most Holocene peat deposits are subject to destruction by erosion, fire and decomposition through microbial and chemical oxidation before burial. The best environments for coal precursors have biomass accumulation, a continuously rising water table within the mass, and minimum influx of clay and silt until preservation by burial. The most suitable settings for future economic coal deposits are domed bogs that accumulate thick, widespread peat having low ash and low sulfur contents. The ombrotrophic peat deposits of tropical Sarawak and Sumatra are thick and extensive, contain low-ash and low-sulfur peat, and have high heating values. They are considered to be the best tropical coal analogs because of their extent and chances of preservation; the base of the peat is below adjacent river levels, and chemical and structural conditions are favorable for accumulation.

International Journal of Coal Geology↗

USGS1998

Developmental geology of coalbed methane from shallow to deep in Rocky Mountain basins and in Cook Inlet-Matanuska Basin, Alaska, USA and Canada

The Rocky Mountain basins of western North America contain vast deposits of coal of Cretaceous through early Tertiary age. Coalbed methane is produced in Rocky Mountain basins at depths ranging from 45 m (150 ft) to 1981 m (6500 ft) from coal of lignite to low-volatile bituminous rank. Although some production has been established in almost all Rocky Mountain basins, commercial production occurs in only a few. despite more than two decades of exploration for coalbed methane in the Rocky Mountain region, it is still difficult to predict production characteristics of coalbed methane wells prior to drilling. Commonly cited problems include low permeabilities, high water production, and coals that are significantly undersaturated with respect to methane. Sources of coalbed gases can be early biogenic, formed during the early stages of coalification, thermogenic, formed during the main stages of coalification, or late stage biogenic, formed as a result of the reintroduction of methane-gnerating bacteria by groundwater after uplift and erosion. Examples of all three types of coalbed gases, and combinations of more than one type, can be found in the Rocky Mountain region. Coals in the Rocky Mountain region achieved their present ranks largely as a result of burial beneath sediments that accumulated during the Laramide orogeny (Late Cretaceous through the end of the eocene) or shortly after. Thermal events since the end of the orogeny have also locally elevated coal ranks. Coal beds in the upper part of high-volatile A bituminous rank or greater commonly occur within much more extensive basin-centered gas deposits which cover large areas of the deeper parts of most Rocky Mountain basins. Within these basin-centered deposits all lithologies, including coals, sandstones, and shales, are gas saturated, and very little water is produced. The interbedded coals and carbonaceous shales are probably the source of much of this gas. Basin-centered gas deposits become overpressured from hydrocarbon generation as they form, and this overpressuring is probably responsible for driving out most of the water. Sandstone permeabilities are low, in part because of diagenesis caused by highly reactive water given off during the early stages of coalification. Coals within these basin-centered deposits commonly have high gas contents and produce little water, but they generally occur at depths greater than 5000 ft and have low permeabilities. Significant uplift and removal of overburden has occurred throughout the Rocky Mountain region since the end of the Eocene, and much of this erosion occurred after regional uplift began about 10 Ma. The removal of overburden generally causes methane saturation levels in coals to decrease, and thus a significant drop in pressure is required to initiate methane production. The most successful coalbed methane production in the Rocky Mountain region occurs in areas where gas contents were increased by post-Eocene thermal events and/or the generation of late-stage biogenic gas. Methane-generating bacteria were apparently reintroduced into the coals in some areas after uplift and erosion, and subsequent changes in pressure and temperature, allowed surface waters to rewater the coals. Groundwater may also help open up cleat systems making coals more permeable to methane. If water production is excessive, however, the economics of producing methane are impacted by the cost of water disposal.The Rocky Mountain basins of western North America contain vast deposits of coal of Cretaceous through early Tertiary age. Coalbed methane is produced in Rocky Mountain basins at depths ranging from 45 to 1981 m from coal of lignite to low volatile bituminous rank. Despite more than two decades of exploration for coalbed methane in Rocky Mountain region, it is still difficult to predict production characteristics of coalbed methane wells prior to drilling. Sources of coalbed gases can be early biogenic, formed during the main stages of coa

International Journal of Coal Geology↗

USGS1979

Measurement of fluid velocity using temperature profiles: Experimental verification

Temperature profiling has been used to predict the rate and direction of groundwater movement. A controlled field experiment was conducted to ascertain the validity of the rate calculations made using this method. The vertical velocity, or leakage, of groundwater between two aquifers was calculated utilizing both hydrologic and temperature measurements in a well drilled into the Paw Paw buried bedrock valley in northern Illinois. The experiment showed that accurate estimates of leakage can be made in stable boreholes where there are no geologic complications. Estimates utilizing temperature and hydrologic methods produced similar results for one of two aquicludes. However, the methods produced dissimilar results for the second aquiclude. It is speculated that the presence of a thin organic silt caused most of the problem; other complicating factors were lithologic variation and a very low hydraulic gradient. Nevertheless, the method appears to have great promise in many geologic environments.

Illinois↗

USGS1981

Concentration of some platinum-group metals in coal

New data on some platinum group metals in coal indicate that the concentration of Pt is generally less than about 5 ppb, that of Pd is generally less than 1 ppb, and that of Rh is generally less than 0.5 ppb. No conclusive evidence was obtained concerning the mode of occurrence of these elements in coal.

International Journal of Coal Geology↗

USGS1981

Rank of coal beds of the Narragansett basin, Massachusetts and Rhode Island

Coal of the Narragansett basin generally has been considered to be anthracite and/or meta-anthracite. However, no single reliable method has been used to distinguish these two ranks in this basin. Three methods — chemical, X-ray, and petrographic — have been used with some degree of success on coal of the Narragansett basin, but too often the results are in conflict. Chemical methods have been limited by inadequate sampling on a coal-bed-by-coal-bed basis and by a lack of analyses made according to (American Society for Testing and Materials, 1974) standard specifications. In addition, when corrections are made by using the Parr formulas, as required by the ASTM (1974) procedures, the generally high to very high ash content of coal from the Narragansett basin causes the fixed-carbon content to appear higher than it actually is. X-ray methods using the degree of graphitization as a measure of rank are not reliable because some of the graphite is related to shearing and brecciation associated with folding and faulting. Petrographic methods using reflectance on vitrinite give results that are generally consistent with results from chemical determinations. However, it is not clear whether the mean maximum reflectance or mean bireflectance is a better indicator of similar rank of such high-rank coals that have been structurally deformed. Coal from the Cranston Mine, RI, is probably meta-anthracite and coal from the Portsmouth Mine is probably anthracite. These ranks are based on chemical,X-ray, and petrographic data and are supported by associated metamorphic mineral assemblages that indicate that the Cranston Mine is in a higher metamorphic zone than the zone containing the Porthmouth Mine. Interpretation of the rank of Mansfield, MA, coal on the basis of extant chemical data is difficult because it is an impure coal with an ash content of 33 to 50%. Reflectance data indicate that the Mansfield, Foxborough, and Plainville coals in the northern part of the Narragansett basin are meta-anthracite but this is in disagreement with the rank suggested by the low degree of metamorphism of the associated rocks.

International Journal of Coal Geology↗

USGS1982

Application of automated image analysis to coal petrography

The coal petrologist seeks to determine the petrographic characteristics of organic and inorganic coal constituents and their lateral and vertical variations within a single coal bed or different coal beds of a particular coal field. Definitive descriptions of coal characteristics and coal facies provide the basis for interpretation of depositional environments, diagenetic changes, and burial history and determination of the degree of coalification or metamorphism. Numerous coal core or columnar samples must be studied in detail in order to adequately describe and define coal microlithotypes, lithotypes, and lithologic facies and their variations. The large amount of petrographic information required can be obtained rapidly and quantitatively by use of an automated image-analysis system (AIAS). An AIAS can be used to generate quantitative megascopic and microscopic modal analyses for the lithologic units of an entire columnar section of a coal bed. In our scheme for megascopic analysis, distinctive bands 2 mm or more thick are first demarcated by visual inspection. These bands consist of either nearly pure microlithotypes or lithotypes such as vitrite/vitrain or fusite/fusain, or assemblages of microlithotypes. Megascopic analysis with the aid of the AIAS is next performed to determine volume percentages of vitrite, inertite, minerals, and microlithotype mixtures in bands 0.5 to 2 mm thick. The microlithotype mixtures are analyzed microscopically by use of the AIAS to determine their modal composition in terms of maceral and optically observable mineral components. Megascopic and microscopic data are combined to describe the coal unit quantitatively in terms of (V) for vitrite, (E) for liptite, (I) for inertite or fusite, (M) for mineral components other than iron sulfide, (S) for iron sulfide, and (VEIM) for the composition of the mixed phases (X i ) i = 1,2, etc. in terms of the maceral groups vitrinite V, exinite E, inertinite I, and optically observable mineral content M. The volume percentage of each component present is indicated by a subscript. For example, a lithologic unit was determined megascopically to have the composition (V) 13 (I) 1 (S) 1 (X 1 ) 83 (X 2 ) 2 . After microscopic analysis of the mixed phases, this composition was expressed as (V) 13 (I) 1 (S) 1 (V 63 E 19 I 14 M 4 ) 83 (V 67 E 11 I 13 M 9 ) 2 . Finally, these data were combined in a description of the bulk composition as V 67 E 16 I 13 M 3 S 1 . An AIAS can also analyze textural characteristics and can be used for quick and reliable determination of rank (reflectance). Our AIAS is completely software based and incorporates a television (TV) camera that has optimum response characteristics in the range of reflectance less than 5%, making it particularly suitable for coal studies. Analysis of the digitized signal from the TV camera is controlled by a microprocessor having a resolution of 64 gray levels between full illumination and dark current. The processed image is reconverted for display on a TV monitor screen, on which selection of phases or features to be analyzed is readily controlled and edited by the operator through use of a lightpen. We expect that automated image analysis, because it can rapidly provide a large amount of pertinent information, will play a major role in the advancement of coal petrography.

International Journal of Coal Geology↗