Search USGS⌕ Search

SEARCH · Search USGS

Results for “Florida Geological Survey Report of Investigations”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10Linked to original sources
USGS2009

EAARL Coastal Topography-Assateague Island National Seashore, 2008: Bare Earth

These remotely sensed, geographically referenced elevation measurements of lidar-derived bare-earth (BE) topography were produced as a collaborative effort between the U.S. Geological Survey (USGS), Florida Integrated Science Center (FISC), St. Petersburg, FL; the National Park Service (NPS), Northeast Coastal and Barrier Network, Kingston, RI; and the National Aeronautics and Space Administration (NASA), Wallops Flight Facility, VA. This project provides highly detailed and accurate datasets of the Assateague Island National Seashore in Maryland and Virginia, acquired March 24-25, 2008. The datasets are made available for use as a management tool to research scientists and natural-resource managers. An innovative airborne lidar instrument originally developed at the NASA Wallops Flight Facility, and known as the Experimental Advanced Airborne Research Lidar (EAARL) was used during data acquisition. The EAARL system is a raster-scanning, waveform-resolving, green-wavelength (532-nanometer) lidar designed to map near-shore bathymetry, topography, and vegetation structure simultaneously. The EAARL sensor suite includes the raster-scanning, water-penetrating full-waveform adaptive lidar, a down-looking red-green-blue (RGB) digital camera, a high-resolution multi-spectral color infrared (CIR) camera, two precision dual-frequency kinematic carrier-phase GPS receivers, and an integrated miniature digital inertial measurement unit, which provide for sub-meter georeferencing of each laser sample. The nominal EAARL platform is a twin-engine Cessna 310 aircraft, but the instrument may be deployed on a range of light aircraft. A single pilot, a lidar operator, and a data analyst constitute the crew for most survey operations. This sensor has the potential to make significant contributions in measuring sub-aerial and submarine coastal topography within cross-environmental surveys. Elevation measurements were collected over the survey area using the EAARL system, and the resulting data were then processed using the Airborne Lidar Processing System (ALPS), a custom-built processing system developed in a NASA-USGS collaboration. ALPS supports the exploration and processing of lidar data in an interactive or batch mode. Modules for pre-survey flight-line definition, flight-path plotting, lidar raster and waveform investigation, and digital camera image playback have been developed. Processing algorithms have been developed to extract the range to the first and last significant return within each waveform. ALPS is used routinely to create maps that represent submerged or sub-aerial topography. Specialized filtering algorithms have been implemented to determine the 'bare earth' under vegetation from a point cloud of last return elevations.

Data Series↗
USGS2009

EAARL Coastal Topography-Pearl River Delta 2008: Bare Earth

These remotely sensed, geographically referenced elevation measurements of Lidar-derived bare earth (BE) topography were produced as a collaborative effort between the U.S. Geological Survey (USGS), Florida Integrated Science Center (FISC), St. Petersburg, FL; the University of New Orleans (UNO), Pontchartrain Institute for Environmental Sciences (PIES), New Orleans, LA; and the National Aeronautics and Space Administration (NASA), Wallops Flight Facility, VA. This project provides highly detailed and accurate datasets of a portion of the Pearl River Delta in Louisiana and Mississippi, acquired March 9-11, 2008. The datasets are made available for use as a management tool to research scientists and natural resource managers. An innovative airborne Lidar instrument originally developed at the NASA Wallops Flight Facility, and known as the Experimental Advanced Airborne Research Lidar (EAARL), was used during data acquisition. The EAARL system is a raster-scanning, waveform-resolving, green-wavelength (532-nanometer) Lidar designed to map near-shore bathymetry, topography, and vegetation structure simultaneously. The EAARL sensor suite includes the raster-scanning, water-penetrating full-waveform adaptive Lidar, a down-looking red-green-blue (RGB) digital camera, a high-resolution multi-spectral color infrared (CIR) camera, two precision dual-frequency kinematic carrier-phase GPS receivers, and an integrated miniature digital inertial measurement unit, which provide for submeter georeferencing of each laser sample. The nominal EAARL platform is a twin-engine Cessna 310 aircraft, but the instrument may be deployed on a range of light aircraft. A single pilot, a Lidar operator, and a data analyst constitute the crew for most survey operations. This sensor has the potential to make significant contributions in measuring sub-aerial and submarine coastal topography within cross-environmental surveys. Elevation measurements were collected over the survey area using the EAARL system, and the resulting data were then processed using the Airborne Lidar Processing System (ALPS), a custom-built processing system developed in a NASA-USGS collaboration. ALPS supports the exploration and processing of Lidar data in an interactive or batch mode. Modules for presurvey flight line definition, flight path plotting, Lidar raster and waveform investigation, and digital camera image playback have been developed. Processing algorithms have been developed to extract the range to the first and last significant return within each waveform. ALPS is used routinely to create maps that represent submerged or first surface topography. Specialized filtering algorithms have been implemented to determine the 'bare earth' under vegetation from a point cloud of last return elevations.

Data Series↗
USGS2009

EAARL Coastal Topography-Pearl River Delta 2008: First Surface

These remotely sensed, geographically referenced elevation measurements of Lidar-derived first surface (FS) topography were produced as a collaborative effort between the U.S. Geological Survey (USGS), Florida Integrated Science Center (FISC), St. Petersburg, FL; the University of New Orleans (UNO), Pontchartrain Institute for Environmental Sciences (PIES), New Orleans, LA; and the National Aeronautics and Space Administration (NASA), Wallops Flight Facility, VA. This project provides highly detailed and accurate datasets of a portion of the Pearl River Delta in Louisiana and Mississippi, acquired March 9-11, 2008. The datasets are made available for use as a management tool to research scientists and natural resource managers. An innovative airborne Lidar instrument originally developed at the NASA Wallops Flight Facility, and known as the Experimental Advanced Airborne Research Lidar (EAARL), was used during data acquisition. The EAARL system is a raster-scanning, waveform-resolving, green-wavelength (532-nanometer) Lidar designed to map near-shore bathymetry, topography, and vegetation structure simultaneously. The EAARL sensor suite includes the raster-scanning, water-penetrating full-waveform adaptive Lidar, a down-looking red-green-blue (RGB) digital camera, a high-resolution multi-spectral color infrared (CIR) camera, two precision dual-frequency kinematic carrier-phase GPS receivers, and an integrated miniature digital inertial measurement unit, which provide for submeter georeferencing of each laser sample. The nominal EAARL platform is a twin-engine Cessna 310 aircraft, but the instrument may be deployed on a range of light aircraft. A single pilot, a Lidar operator, and a data analyst constitute the crew for most survey operations. This sensor has the potential to make significant contributions in measuring sub-aerial and submarine coastal topography within cross-environmental surveys. Elevation measurements were collected over the survey area using the EAARL system, and the resulting data were then processed using the Airborne Lidar Processing System (ALPS), a custom-built processing system developed in a NASA-USGS collaboration. ALPS supports the exploration and processing of Lidar data in an interactive or batch mode. Modules for presurvey flight line definition, flight path plotting, Lidar raster and waveform investigation, and digital camera image playback have been developed. Processing algorithms have been developed to extract the range to the first and last significant return within each waveform. ALPS is used routinely to create maps that represent submerged or first surface topography. Specialized filtering algorithms have been implemented to determine the 'bare earth' under vegetation from a point cloud of last return elevations.

Data Series↗
USGS2014

EAARL-B coastal topography: Fire Island, New York, pre-Hurricane Sandy, 2012: seamless (bare earth and submerged)

These remotely sensed, geographically referenced elevation measurements of lidar-derived seamless (bare-earth and submerged) topography datasets were produced by the U.S. Geological Survey (USGS), St. Petersburg Coastal and Marine Science Center, St. Petersburg, Florida. This project provides highly detailed and accurate datasets for part of Fire Island, New York, acquired pre-Hurricane Sandy on October 27, 2012. The datasets are made available for use as a management tool to research scientists and natural-resource managers. An innovative airborne lidar, known as the second-generation Experimental Advanced Airborne Research Lidar (EAARL-B), was used during data acquisition. The EAARL-B system is a raster-scanning, waveform-resolving, green-wavelength (532-nm) lidar designed to map near-shore bathymetry, topography, and vegetation structure simultaneously. The EAARL-B sensor suite includes the raster-scanning, water-penetrating full-waveform adaptive lidar, down-looking red-green-blue (RGB) and infrared (IR) digital cameras, two precision dual-frequency kinematic carrier-phase GPS receivers, and an integrated miniature digital inertial measurement unit, which provide for sub-meter georeferencing of each laser sample. The nominal EAARL-B platform is a twin-engine Cessna 310 aircraft, but the instrument may be deployed on a range of light aircraft. A single pilot, a lidar operator, and a data analyst constitute the crew for most survey operations. This sensor has the potential to make significant contributions in measuring sub-aerial and submarine coastal topography within cross-environmental surveys. Elevation measurements were collected over the survey area using the EAARL-B system. The resulting data were then processed using the Airborne Lidar Processing System (ALPS), a custom-built processing system developed originally in a NASA-USGS collaboration. The exploration and processing of lidar data in an interactive or batch mode is supported using ALPS. Modules for presurvey flight-line definition, flight-path plotting, lidar raster and waveform investigation, and digital camera image playback have been developed. Processing algorithms have been developed to extract the range to the first and last significant return within each waveform. The Airborne Lidar Processing System (ALPS) is used routinely to create maps that represent submerged or sub-aerial topography. Specialized filtering algorithms have been implemented to determine the "bare earth" under vegetation from a point cloud of last return elevations. For more information about similar projects, please visit the Lidar for Science and Resource Management Web site.

New York↗
USGS2008

Assessment of Water-Quality Monitoring and a Proposed Water-Quality Monitoring Network for the Mosquito Lagoon Basin, East-Central Florida

Surface- and ground-water quality data from the Mosquito Lagoon Basin were compiled and analyzed to: (1) describe historical and current monitoring in the basin, (2) summarize surface- and ground-water quality conditions with an emphasis on identifying areas that require additional monitoring, and (3) develop a water-quality monitoring network to meet the goals of Canaveral National Seashore (a National Park) and to fill gaps in current monitoring. Water-quality data were compiled from the U.S. Environmental Protection Agency's STORET system, the U.S. Geological Survey's National Water Information System, or from the agency which collected the data. Most water-quality monitoring focused on assessing conditions in Mosquito Lagoon. Significant spatial and/or seasonal variations in water-quality constituents in the lagoon were quantified for pH values, fecal coliform bacteria counts, and concentrations of dissolved oxygen, total nitrogen, total phosphorus, chlorophyll-a, and total suspended solids. Trace element, pesticide, and ground-water-quality data were more limited. Organochlorine insecticides were the major class of pesticides analyzed. A surface- and ground-water-quality monitoring network was designed for the Mosquito Lagoon Basin which emphasizes: (1) analysis of compounds indicative of human activities, including pesticides and other trace organic compounds present in domestic and industrial waste; (2) greater data collection in the southern part of Mosquito Lagoon where spatial variations in water-quality constituents were quantified; and (3) additional ground-water-quality data collection in the surficial aquifer system and Upper Floridan aquifer. Surface-water-quality data collected as part of this network would include a fixed-station monitoring network of eight sites in the southern part of the basin, including a canal draining Oak Hill. Ground-water quality monitoring should be done routinely at about 20 wells in the surficial aquifer system and Upper Floridan aquifer, distributed between developed and undeveloped parts of the basin. Water samples collected should be analyzed for a wide range of constituents, including physical properties, nutrients, suspended sediment, and constituents associated with increased urban development such as pesticides, other trace organic compounds associated with domestic and industrial waste, and trace elements.

Scientific Investigations Report↗
USGS2014

EAARL-B coastal topography: eastern New Jersey, Hurricane Sandy, 2012: first surface

These remotely sensed, geographically referenced elevation measurements of lidar-derived first-surface (FS) topography datasets were produced by the U.S. Geological Survey (USGS), St. Petersburg Coastal and Marine Science Center, St. Petersburg, Florida. This project provides highly detailed and accurate datasets for a portion of the New Jersey coastline beachface, acquired pre-Hurricane Sandy on October 26, and post-Hurricane Sandy on November 1 and November 5, 2012. The datasets are made available for use as a management tool to research scientists and natural-resource managers. An innovative airborne lidar system, known as the second-generation Experimental Advanced Airborne Research Lidar (EAARL-B), was used during data acquisition. The EAARL-B system is a raster-scanning, waveform-resolving, green-wavelength (532-nm) lidar designed to map nearshore bathymetry, topography, and vegetation structure simultaneously. The EAARL-B sensor suite includes the raster-scanning, water-penetrating full-waveform adaptive lidar, down-looking red-green-blue (RGB) and infrared (IR) digital cameras, two precision dual-frequency kinematic carrier-phase GPS receivers, and an integrated miniature digital inertial measurement unit, which provide for sub-meter georeferencing of each laser sample. The nominal EAARL-B platform is a twin-engine Cessna 310 aircraft, but the instrument may be deployed on a range of light aircraft. A single pilot, a lidar operator, and a data analyst constitute the crew for most survey operations. This sensor has the potential to make significant contributions in measuring sub-aerial and submarine coastal topography within cross-environmental surveys. Elevation measurements were collected over the survey area using the EAARL-B system. The resulting data were then processed using the Airborne Lidar Processing System (ALPS), a custom-built processing system developed in a NASA-USGS collaboration. ALPS supports the exploration and processing of lidar data in an interactive or batch mode. Modules for presurvey flight-line definition, flight-path plotting, lidar raster and waveform investigation, and digital camera image playback have been developed. Processing algorithms have been developed to extract the range to the first and last significant return within each waveform. ALPS is used routinely to create maps that represent submerged or sub-aerial topography. Specialized filtering algorithms have been implemented to determine the "bare earth" under vegetation from a point cloud of last return elevations. For more information about similar projects, please visit the Lidar for Science and Resource Management Web site.

New Jersey↗
USGS2014

EAARL-B submerged topography: Barnegat Bay, New Jersey, pre-Hurricane Sandy, 2012

These remotely sensed, geographically referenced elevation measurements of lidar-derived submerged topography datasets were produced by the U.S. Geological Survey (USGS), St. Petersburg Coastal and Marine Science Center, St. Petersburg, Florida. This project provides highly detailed and accurate datasets for part of Barnegat Bay, New Jersey, acquired pre-Hurricane Sandy on October 18, 22, 23, and 26, 2012. The datasets are made available for use as a management tool to research scientists and natural-resource managers. An innovative airborne lidar, known as the second-generation Experimental Advanced Airborne Research Lidar (EAARL-B), was used during data acquisition. The EAARL-B system is a raster-scanning, waveform-resolving, green-wavelength (532-nm) lidar designed to map near-shore bathymetry, topography, and vegetation structure simultaneously. The EAARL-B sensor suite includes the raster-scanning, water-penetrating full-waveform adaptive lidar, down-looking red-green-blue (RGB) and infrared (IR) digital cameras, two precision dual-frequency kinematic carrier-phase GPS receivers, and an integrated miniature digital inertial measurement unit, which provide for sub-meter georeferencing of each laser sample. The nominal EAARL-B platform is a twin-engine Cessna 310 aircraft, but the instrument may be deployed on a range of light aircraft. A single pilot, a lidar operator, and a data analyst constitute the crew for most survey operations. This sensor has the potential to make significant contributions in measuring sub-aerial and submarine coastal topography within cross-environmental surveys. Elevation measurements were collected over the survey area using the EAARL-B system. The resulting data were then processed using the Airborne Lidar Processing System (ALPS), a custom-built processing system developed originally in a NASA-USGS collaboration. The exploration and processing of lidar data in an interactive or batch mode is supported using ALPS. Modules for presurvey flight-line definition, flight-path plotting, lidar raster and waveform investigation, and digital camera image playback have been developed. Processing algorithms have been developed to extract the range to the first and last significant return within each waveform. The Airborne Lidar Processing System (ALPS) is used routinely to create maps that represent submerged or sub-aerial topography. Specialized filtering algorithms have been implemented to determine the "bare earth" under vegetation from a point cloud of last return elevations. For more information about similar projects, please visit the Lidar for Science and Resource Management Web site.

New Jersey↗
USGS1990

Water-resources potential of the freshwater lens at Key West, Florida

The island of Key West lies at the end of the Florida Keys, about 150 miles southwest of Miami. The public-water supply for the island is provided by the Florida Keys Aqueduct Authority Well Field near Miami. However, there are many privately owned wells on the island that tap the local fresh ground-water lens for potable and nonpotable water supply. The number of people who use water from the wells for drinking purposes is unknown. From 1985 to 1988, the U.S. Geological Survey, in cooperation with the South Florida Water Management District, conducted an investigation to characterize the Key West freshwater lens. Observation wells were drilled to determine the extent of the lens and to characterize the water quality. Previous well logs and well-core data collected during the investigation showed the aquifer to be a highly permeable, porous, solution-riddled, oolitic limestone that allows rainfall recharge to quickly seep into the ocean and saltwater to easily intrude the aquifer. The small freshwater lens (250 milligrams per liter of chloride concentration, or less) averages 5 feet in thickness below the center of the western half (Old Town) of the island. The lens contains about 20 million gallons of fresh-water during the dry season and about 30 million gallons during the wet season. Underlying the freshwater lens is a transition zone of freshwater-saltwater mix that extends to the saltwater interface (19,000 milligrams per liter of chloride concentration), which is about 40-feet deep at the center of the lens. The water table fluctuates and the configuration of the lens constantly changes, largely as a result of tidal effects. Other events, such as rainfall, pumping, and evapotranspiration, are masked by the tidal effects. The freshwater lens is a calcium bicarbonate water that grades to a sodium chloride type near the saltwater interface. Elevated concentrations of nitrate nitrogen were found in water samples from wells in the Old Town district. However, concentrations generally were not above the maximum contaminant level of 10 milligrams per liter for drinking water established by the Florida Department of Environmental Regulation. Water samples near an old land-fill in the eastern half of the island had concentrations of iron (600-1,900 micrograms per liter) and lead (40-800 micrograms per liter) that extended maximum contaminant levels of 300 and 50 micrograms per liter. These trace-element concentrations generally decreased with distance from the landfill. Although the freshwater lens is a potential source of water for additional nonpotable water needs in Key West, any large-scale pumping could quickly exhaust the freshwater lens, and saline water could be rapidly drawn though the porous limestone aquifer. Water-quality data indicate that the lens is an unlikely source of potable water.

Florida↗
USGS2014

EAARL-B submerged topography: Barnegat Bay, New Jersey, post-Hurricane Sandy, 2012-2013

These remotely sensed, geographically referenced elevation measurements of lidar-derived submerged topography datasets were produced by the U.S. Geological Survey (USGS), St. Petersburg Coastal and Marine Science Center, St. Petersburg, Florida. This project provides highly detailed and accurate datasets for part of Barnegat Bay, New Jersey, acquired post-Hurricane Sandy on November 1, 5, 16, 20, and 30, 2012; December 5, 6, and 21, 2012; and January 10, 2013. The datasets are made available for use as a management tool to research scientists and natural-resource managers. An innovative airborne lidar system, known as the second-generation Experimental Advanced Airborne Research Lidar (EAARL-B), was used during data acquisition. The EAARL-B system is a raster-scanning, waveform-resolving, green-wavelength (532-nm) lidar designed to map nearshore bathymetry, topography, and vegetation structure simultaneously. The EAARL-B sensor suite includes the raster-scanning, water-penetrating full-waveform adaptive lidar, down-looking red-green-blue (RGB) and infrared (IR) digital cameras, two precision dual-frequency kinematic carrier-phase GPS receivers, and an integrated miniature digital inertial measurement unit, which provide for sub-meter georeferencing of each laser sample. The nominal EAARL-B platform is a twin-engine Cessna 310 aircraft, but the instrument may be deployed on a range of light aircraft. A single pilot, a lidar operator, and a data analyst constitute the crew for most survey operations. This sensor has the potential to make significant contributions in measuring sub-aerial and submarine coastal topography within cross-environmental surveys. Elevation measurements were collected over the survey area using the EAARL-B system. The resulting data were then processed using the Airborne Lidar Processing System (ALPS), a custom-built processing system developed originally in a NASA-USGS collaboration. The exploration and processing of lidar data in an interactive or batch mode is supported using ALPS. Modules for presurvey flight-line definition, flight-path plotting, lidar raster and waveform investigation, and digital camera image playback have been developed. Processing algorithms have been developed to extract the range to the first and last significant return within each waveform. The Airborne Lidar Processing System (ALPS) is used routinely to create maps that represent submerged or sub-aerial topography. Specialized filtering algorithms have been implemented to determine the "bare earth" under vegetation from a point cloud of last return elevations. For more information about similar projects, please visit the Lidar for Science and Resource Management Web site .

New Jersey↗
USGS2009

Factors Affecting Water Quality in Domestic Wells in the Upper Floridan Aquifer, Southeastern United States, 1998-2005

The Floridan aquifer system is a highly productive carbonate aquifer that provides drinking water to about 10 million people in Florida, Georgia, and South Carolina. Approximately 1.6 million people rely on domestic wells (privately owned household wells) for drinking water. Withdrawals of water from the Floridan aquifer system have increased by more than 500 percent from 630 million gallons per day (2.38 cubic meters per day) in 1950 to 4,020 million gallons per day (15.2 cubic meters per day) in 2000, largely due to increases in population, tourism, and agriculture production. Water samples were collected from 148 domestic wells in the Upper Floridan aquifer in Florida, Georgia, South Carolina, and Alabama during 1998-2005 as part of the U.S. Geological Survey (USGS) National Water-Quality Assessment Program. The wells were located in different hydrogeologic settings based on confinement of the Upper Floridan aquifer. Five networks of wells were sampled con-sisting of 28 to 30 wells each: two networks were in unconfined areas, two networks were in semiconfined areas, and one network was in the confined area. Physical properties and concentrations of major ions, trace elements, nutrients, radon, and organic compounds (volatile organic compounds and pesticides) were measured in water samples. Concentrations were compared to water-quality benchmarks for human health, either U.S. Environmental Protection Agency (USEPA) Maximum Contaminant Levels (MCLs) for public water supplies or USGS Health-Based Screening Levels (HBSLs). The MCL for fluoride of 4 milligrams per liter (mg/L) was exceeded for two samples (about 1 percent of samples). A proposed MCL for radon of 300 picocuries per liter was exceeded in about 40 percent of samples. Nitrate concentrations in the Upper Floridan aquifer ranged from less than the laboratory reporting level of 0.06 to 8 mg/L, with a median nitrate concentration less than 0.06 mg/L (as nitrogen). Nitrate concentrations did not exceed the MCL of 10 mg/L. Statistical comparisons indicated that median nitrate concentrations were significantly different by degree of confinement where the highest median nitrate concentration was 1.46 mg/L for 58 samples from unconfined areas, and by network, where the highest median nitrate concentration was 2.43 mg/L in 28 samples from unconfined areas in southwestern Georgia. Nitrate concentrations in unconfined areas were positively correlated to: (1) the percentage of agricultural land use around the well, (2) the amount of nitrogen fertilizer applied, and (3) the dissolved oxygen concentrations in groundwater. Volatile organic compounds (VOCs) were detected in about 63 percent of all samples. Chloroform, carbon disulfide, and 1,2-dichloropropane were the most frequently detected VOCs. Chloroform, a byproduct of water chlorination, was most frequently detected in unconfined urban areas. Carbon disulfide, a solvent, was most frequently detected in confined areas in southeastern Georgia. Pesticides were detected in about 21 percent of all samples, but were detected in about 69 percent of the 28 samples from unconfined areas in southwestern Georgia. The herbicides atrazine, deethylatrazine, and metolachlor were the most frequently detected pesticides.

Scientific Investigations Report↗
USGS1995

Recharge to the surficial aquifer system in Lee and Hendry counties, Florida

Protection of ground-water recharge areas against contamination is of great interest in Florida, a State whose population depends heavily on ground water and that is experiencing rapid growth. The Florida Legislature is considering implementation of a tax incentive program to owners of high-rate recharge lands that remain undeveloped. High-rate recharge was arbitrarily set at 10 or more inches per year. The U.S. Geological Survey, in cooperation with the South Florida Water Management District, conducted a study to investigate the efficacy of several methods for estimating recharge to the surficial aquifer system in southwestern Florida and to map recharge at a scale of 1:100,000. Four maps were constructed at a scale of 1:100,000 for Lee and Hendry Counties, depicting the configuration of the water table of the surficial aquifer system, direction of ground-water flow, general soil characteristics, and recharge rates. Point recharge rates calculated for 25 sites in Lee County from comparisons of chloride concentrations in precipitation and in water from the surficial aquifer system ranged from 0.6 to 9.0 inches per year. Local recharge rates estimated by increases in flow along theoretical flow tubes in the surficial aquifer system were 8.0 inches per year in a part of Lee County and 8.2 inches per year in a part of Hendry County. Information on oxygen isotopes in precipitation and water from the surficial aquifer system was used to verify that the source of chlorides in the aquifer system was from precipitation rather than upward leakage of saline water. Soil maps and general topographic and hydrologic considerations were used with calculated point and local recharge rates to regionalize rates throughout Lee and Hendry Counties. The areas of greatest recharge were found in soils of flatwoods and sloughs, which were assigned estimated recharge rates of 0 to 10 inches per year. Soils of swamps and sloughs were assigned values of 0 to 3.0 inches per year; soils of tidal areas and barrier islands, soils of the Everglades, and soils of sloughs and freshwater marshes were assigned values of 0 to 2.0 inches per year; lastly, soils of manmade areas were assigned values of 0.5 to 1.5 inches per year. Small isolated areas of high-rate recharge (greater than 10 inches per year) might exist in Lee and Hendry Counties, but the maximum rate calculated in this study was 9.0 inches per year. Despite low natural recharge rates, lowering of the water table through pumping or canalization could create a potential for induced recharge in excess of 10 inches per year in parts of Lee and Hendry Counties.

Water-Resources Investigations Report↗
USGS2024

Evaporation from the interior of Lake Okeechobee—A large freshwater lake in Florida, 2013–16

In 2012, a platform at the approximate center of Lake Okeechobee in central Florida was instrumented to continuously measure evaporation with the Bowen-ratio energy-budget method as part of a long-term partnership between the South Florida Water Management District and the U.S. Geological Survey. The primary goal for the study was to quantify daily rates of open-water evaporation. A secondary goal was to assess differences in evaporation rates among alternate methods and determine if instrumentation and operational expenses associated with the Bowen-ratio method could be reduced. Mean annual evaporation from Lake Okeechobee for 2013–16 was about 1,825 millimeters per year. Annual evaporation from 2013 to 2016 was 1,760, 1,840, 1,810, and 1,890 millimeters per year, respectively. These evaporation rates are among the highest rates observed in Florida based on scientifically vetted methods such as evaporation pans, lysimeters, eddy-covariance, or Bowen-ratio methods. The high evaporation rates are largely a result of frequent clear-sky conditions over the interior of Lake Okeechobee, which allows solar radiation to reach the water surface and drive open-water evaporation. Cloud formation over the interior of Lake Okeechobee is suppressed because of a relatively large heat capacity for water that buffers convective fluxes of air that form clouds while rising and cooling. Estimated evaporation rates obtained using five alternative methods were compared to measured Bowen-ratio energy-budget daily, monthly, and annual evaporation: the Penman, Priestly-Taylor, Mass-Transfer, Simple, and Turc equations. All five methods performed relatively well (within 10 percent of the Bowen ratio annual totals). The Penman, Priestley-Taylor, and Mass-Transfer methods captured relatively large evaporation rates that occurred in the winter due to cold fronts, because these methods account for large wind speeds and vapor pressure deficits associated with the regional cold fronts. For operational implementation, the Simple, Mass-Transfer, or Turc methods are likely preferable because of their simplicity, limited data requirements, and improved accuracy for computing monthly and annual evaporation totals. The Turc equation computed monthly evaporation within 8 percent of the Bowen-ratio method, while requiring only air temperature and solar radiation data. The Simple equation achieved similar accuracy while requiring only solar radiation data.

Florida↗
USGS2000

Cruise report RV Ocean Surveyor cruise O-1-00-GM the bathymetry and acoustic backscatter of the Pinnacles area, northern Gulf of Mexico May 23, through June 10, 2000 Venice, LA to Venice, LA

An extensive deep (~100 m) reef tract occurs on the Mississippi-Alabama outer continental shelf (OCS). The tract, known as "The Pinnacles", is apparently part of a sequence of drowned reef complexes along the "40-fathom" shelf edge of the northern Gulf of Mexico (Ludwick and Walton, 1957). It is critical to determine the accurate geomorphology of deep-reefs because of their importance as benthic habitats for fisheries. The Pinnacles were mapped by Ludwick and Walton (1957) using a single-beam echo sounder but the spatial extent and morphology were interpreted from a series of widely separated, poorly navigated bathymetric profiles. Other recent studies, supported by Minerals Management Service (MMS), used towed sidescan sonars and single-channel seismic-reflection profiling. None of the existing studies provide the quality of geomorphic data necessary for reasonable habitat studies. The fish faunas of shallow hermatypic reefs have been well studied, but those of deep ahermatypic reefs have relatively ignored. The ecology of deep ahermatypic reefs is fundamentally different from hermatipic reefs because autochthonous intracellular symbiotic zooxanthellae (the carbon source for hermatypic corals) do not form the base of the trophic web. Instead, exogenous plankton, transported to the reef by currents, serves as the primary carbon source. Deep OCS reefs also lie below the practical working depths for SCUBA; consequently, remote investigations from a ship or in situ investigations using submersibles or ROVs are required. Community structure and trophodynamics of demersal fishes of the Pinnacles are presently the focus of USGS reseach. A goal of the research is to answer questions concerning the relataive roles played by geomorphology and surficial geology in the interaction with and control of biological differentiation. OCS reefs are important because we now know that such areas are important coral reef fish havens, key spawning 2 sites, and a critical early larval and juvenile habitats for economically important sport/food fishes. Also, deep-reef ecosystems as well as the fish populations they sustain are impacted by intensive oil-field development. It is now known that deep OCS reefs function as a key source of re-population (via seasonal and ontogenetic migration) of already heavily impacted inshore reefs. A reflection of this realization is the recent closure by the Gulf States Fisheries Management Council of a 600 mi 2 area of the Florida Middle Grounds (another unmapped major "40-fathom" OCS reef complex) to commercial fishing to preserve grouper spawning aggregations. It is known that the Pinnacles reefs support a lush fauna of ahermatypic hard corals, soft corals, black corals, sessile crinoids and sponges—together forming a living habitat for a well-developed fish fauna. The fish fauna comprises typical Caribbean reef fishes and Carolinian shelf fishes, plus epipelagic fishes, and a few deep-sea fishes. The base of the megafaunal invertebrate food web is plankton, borne by essentially continuous semi-laminar currents flowing predominantly out of the SW, up, along and across the shelf edge. These currents are intercepted by pinnacles reefs, which lie roughly in two linear tracts, parallel to the coastline (see fig. 1 in report). USGS research initiated in 1997 (Sulak et al., in progress) has demonstrated that the Pinnacles reef fish fauna is dominated by planktivorous fishes. Ongoing food habits, trophic web and stable isotope analyses by the USGS are reinforcing a basic picture of deep OCS reefs as ecosystems based on exogenous current-borne plankton. Long-term current meter deployments have demonstrated that the >3 m, <16m relief of the Pinnacles reefs disrupts the prevailing currents, inducing local complexity (F. Kelly, Texas A&M Univ., pers. comm.) favorable to plankton and planktivores. Geodetically accurate bathymetry maps, coregistered with calibrated acoustic backscatter maps, are critical to delineate benthic biotopes, and are essential to correlate biological community differentiation with the physical environment. Previous mapping of the Pinnacles area using the TAMU towed single-beam sidescan system (Anonymous., 1999) employed technology with inherent deficiencies in backscatter calibration, bathymetric precision, and geo-referencing. The resulting bathymetric interpretations of TAMU data are further degraded by ship-track-parallel artifacts that obliterate geomorphology rendering them inadequate to provide high-resolution mapping of individual target reefs (typical maximum relief 15 m, diameter 200-500 m). The sidescan-sonar surveys of the area (Laswell et al., 1990) suffer many of the same deficiencies as the TAMU data so they add no quantitative and little qualitative information about the geomorphology and surficial geology.

Gulf of Mexico, the Pinnacles area↗
USGS2010

EAARL Coastal Topography and Imagery-Naval Live Oaks Area, Gulf Islands National Seashore, Florida, 2007

These remotely sensed, geographically referenced color-infrared (CIR) imagery and elevation measurements of lidar-derived bare-earth (BE) topography, first-surface (FS) topography, and canopy-height (CH) datasets were produced collaboratively by the U.S. Geological Survey (USGS), St. Petersburg Science Center, St. Petersburg, FL; the National Park Service (NPS), Gulf Coast Network, Lafayette, LA; and the National Aeronautics and Space Administration (NASA), Wallops Flight Facility, VA. This project provides highly detailed and accurate datasets of the Naval Live Oaks Area in Florida's Gulf Islands National Seashore, acquired June 30, 2007. The datasets are made available for use as a management tool to research scientists and natural-resource managers. An innovative airborne lidar instrument originally developed at the NASA Wallops Flight Facility, and known as the Experimental Advanced Airborne Research Lidar (EAARL), was used during data acquisition. The EAARL system is a raster-scanning, waveform-resolving, green-wavelength (532-nanometer) lidar designed to map near-shore bathymetry, topography, and vegetation structure simultaneously. The EAARL sensor suite includes the raster-scanning, water-penetrating full-waveform adaptive lidar, a down-looking red-green-blue (RGB) digital camera, a high-resolution multispectral CIR camera, two precision dual-frequency kinematic carrier-phase GPS receivers, and an integrated miniature digital inertial measurement unit, which provide for sub-meter georeferencing of each laser sample. The nominal EAARL platform is a twin-engine Cessna 310 aircraft, but the instrument may be deployed on a range of light aircraft. A single pilot, a lidar operator, and a data analyst constitute the crew for most survey operations. This sensor has the potential to make significant contributions in measuring sub-aerial and submarine coastal topography within cross-environmental surveys. Elevation measurements were collected over the survey area using the EAARL system, and the resulting data were then processed using the Airborne Lidar Processing System (ALPS), a custom-built processing system developed in a NASA-USGS collaboration. ALPS supports the exploration and processing of lidar data in an interactive or batch mode. Modules for presurvey flight-line definition, flight-path plotting, lidar raster and waveform investigation, and digital camera image playback have been developed. Processing algorithms have been developed to extract the range to the first and last significant return within each waveform. ALPS is used routinely to create maps that represent submerged or sub-aerial topography. Specialized filtering algorithms have been implemented to determine the 'bare earth' under vegetation from a point cloud of last return elevations. For more information about similar projects, please visit the Decision Support for Coastal Science and Management website.

Data Series↗
USGS2010

EAARL Coastal Topography-Eastern Florida, Post-Hurricane Jeanne, 2004: First Surface

These remotely sensed, geographically referenced elevation measurements of lidar-derived first-surface (FS) topography datasets were produced collaboratively by the U.S. Geological Survey (USGS), St. Petersburg Coastal and Marine Science Center, St. Petersburg, FL, and the National Aeronautics and Space Administration (NASA), Wallops Flight Facility, VA. This project provides highly detailed and accurate datasets of a portion of the eastern Florida coastline beachface, acquired post-Hurricane Jeanne (September 2004 hurricane) on October 1, 2004. The datasets are made available for use as a management tool to research scientists and natural-resource managers. An innovative airborne lidar instrument originally developed at the NASA Wallops Flight Facility, and known as the Experimental Advanced Airborne Research Lidar (EAARL), was used during data acquisition. The EAARL system is a raster-scanning, waveform-resolving, green-wavelength (532-nanometer) lidar designed to map near-shore bathymetry, topography, and vegetation structure simultaneously. The EAARL sensor suite includes the raster-scanning, water-penetrating full-waveform adaptive lidar, a down-looking red-green-blue (RGB) digital camera, a high-resolution multispectral color-infrared (CIR) camera, two precision dual-frequency kinematic carrier-phase GPS receivers, and an integrated miniature digital inertial measurement unit, which provide for sub-meter georeferencing of each laser sample. The nominal EAARL platform is a twin-engine Cessna 310 aircraft, but the instrument may be deployed on a range of light aircraft. A single pilot, a lidar operator, and a data analyst constitute the crew for most survey operations. This sensor has the potential to make significant contributions in measuring sub-aerial and submarine coastal topography within cross-environmental surveys. Elevation measurements were collected over the survey area using the EAARL system, and the resulting data were then processed using the Airborne Lidar Processing System (ALPS), a custom-built processing system developed in a NASA-USGS collaboration. ALPS supports the exploration and processing of lidar data in an interactive or batch mode. Modules for presurvey flight-line definition, flight-path plotting, lidar raster and waveform investigation, and digital camera image playback have been developed. Processing algorithms have been developed to extract the range to the first and last significant return within each waveform. ALPS is used routinely to create maps that represent submerged or sub-aerial topography. Specialized filtering algorithms have been implemented to determine the 'bare earth' under vegetation from a point cloud of last return elevations. For more information about similar projects, please visit the Decision Support for Coastal Science and Management website.

Data Series↗
USGS2013

EAARL coastal topography and imagery–Western Louisiana, post-Hurricane Rita, 2005: First surface

These remotely sensed, geographically referenced color-infrared (CIR) imagery and elevation measurements of lidar-derived first-surface (FS) topography datasets were produced by the U.S. Geological Survey (USGS), St. Petersburg Coastal and Marine Science Center, St. Petersburg, Florida, and the National Aeronautics and Space Administration (NASA), Wallops Flight Facility, Virginia. This project provides highly detailed and accurate datasets of a portion of the Louisiana coastline beachface, acquired post-Hurricane Rita on September 27-28 and October 2, 2005. The datasets are made available for use as a management tool to research scientists and natural-resource managers. An innovative airborne lidar instrument originally developed at the National Aeronautics and Space Administration (NASA) Wallops Flight Facility, and known as the Experimental Advanced Airborne Research Lidar (EAARL), was used during data acquisition. The EAARL system is a raster-scanning, waveform-resolving, green-wavelength (532-nanometer) lidar designed to map near-shore bathymetry, topography, and vegetation structure simultaneously. The EAARL sensor suite includes the raster-scanning, water-penetrating full-waveform adaptive lidar, a down-looking red-green-blue (RGB) digital camera, a high-resolution multispectral color-infrared (CIR) camera, two precision dual-frequency kinematic carrier-phase GPS receivers, and an integrated miniature digital inertial measurement unit, which provide for sub-meter georeferencing of each laser sample. The nominal EAARL platform is a twin-engine Cessna 310 aircraft, but the instrument may be deployed on a range of light aircraft. A single pilot, a lidar operator, and a data analyst constitute the crew for most survey operations. This sensor has the potential to make significant contributions in measuring sub-aerial and submarine coastal topography within cross-environmental surveys. Elevation measurements were collected over the survey area using the EAARL system, and the resulting data were then processed using the Airborne Lidar Processing System (ALPS), a custom-built processing system developed in a NASA-USGS collaboration. ALPS supports the exploration and processing of lidar data in an interactive or batch mode. Modules for presurvey flight-line definition, flight-path plotting, lidar raster and waveform investigation, and digital camera image playback have been developed. Processing algorithms have been developed to extract the range to the first and last significant return within each waveform. ALPS is used routinely to create maps that represent submerged or sub-aerial topography. Specialized filtering algorithms have been implemented to determine the "bare earth" under vegetation from a point cloud of last return elevations. For more information about similar projects, please visit the Lidar for Science and Resource Management Website.

Louisiana↗
USGS1996

A coupled surface-water and ground-water flow model (MODBRANCH) for simulation of stream-aquifer interaction

Ground-water and surface-water flow models traditionally have been developed separately, with interaction between subsurface flow and streamflow either not simulated at all or accounted for by simple formulations. In areas with dynamic and hydraulically well-connected ground-water and surface-water systems, stream-aquifer interaction should be simulated using deterministic responses of both systems coupled at the stream-aquifer interface. Accordingly, a new coupled ground-water and surface-water model was developed by combining the U.S. Geological Survey models MODFLOW and BRANCH; the interfacing code is referred to as MODBRANCH. MODFLOW is the widely used modular three-dimensional, finite-difference ground-water model, and BRANCH is a one-dimensional numerical model commonly used to simulate unsteady flow in open- channel networks. MODFLOW was originally written with the River package, which calculates leakage between the aquifer and stream, assuming that the stream's stage remains constant during one model stress period. A simple streamflow routing model has been added to MODFLOW, but is limited to steady flow in rectangular, prismatic channels. To overcome these limitations, the BRANCH model, which simulates unsteady, nonuniform flow by solving the St. Venant equations, was restructured and incorporated into MODFLOW. Terms that describe leakage between stream and aquifer as a function of streambed conductance and differences in aquifer and stream stage were added to the continuity equation in BRANCH. Thus, leakage between the aquifer and stream can be calculated separately in each model, or leakages calculated in BRANCH can be used in MODFLOW. Total mass in the coupled models is accounted for and conserved. The BRANCH model calculates new stream stages for each time interval in a transient simulation based on upstream boundary conditions, stream properties, and initial estimates of aquifer heads. Next, aquifer heads are calculated in MODFLOW based on stream stages calculated by BRANCH, aquifer properties, and stresses. This process is repeated until convergence criteria are met for head and stage. Because time steps used in ground-water modeling can be much longer than time intervals used in surface- water simulations, provision has been made for handling multiple BRANCH time intervals within one MODFLOW time step. An option was also added to BRANCH to allow the simulation of channel drying and rewetting. Testing of the coupled model was verified by using data from previous studies; by comparing results with output from a simpler, four-point implicit, open-channel flow model linked with MODFLOW; and by comparison to field studies of L-31N canal in southern Florida.

Techniques of Water-Resources Investigations↗
USGS1994

Quality-assurance results for routine water analysis in US Geological Survey laboratories, water year 1991

The US. Geological Survey operates a quality- assurance program based on the analyses of reference samples for the National Water Quality Laboratory in Arvada, Colorado, and the Quality of Water Service Unit in Ocala, Florida. Reference samples containing selected inorganic, nutrient, and low ionic-strength constituents are prepared and disguised as routine samples. The program goal is to determine precision and bias for as many analytical methods offered by the participating laboratories as possible. The samples typically are submitted at a rate of approximately 5 percent of the annual environmental sample load for each constituent. The samples are distributed to the laboratories throughout the year. Analytical data for these reference samples reflect the quality of environmental sample data produced by the laboratories because the samples are processed in the same manner for all steps from sample login through data release. The results are stored permanently in the National Water Data Storage and Retrieval System. During water year 1991, 86 analytical procedures were evaluated at the National Water Quality Laboratory and 37 analytical procedures were evaluated at the Quality of Water Service Unit. An overall evaluation of the inorganic (major ion and trace metal) constituent data for water year 1991 indicated analytical imprecision in the National Water Quality Laboratory for 5 of 67 analytical procedures: aluminum (whole-water recoverable, atomic emission spectrometric, direct-current plasma); calcium (atomic emission spectrometric, direct); fluoride (ion-exchange chromatographic); iron (whole-water recoverable, atomic absorption spectrometric, direct); and sulfate (ion-exchange chromatographic). The results for 11 of 67 analytical procedures had positive or negative bias during water year 1991. Analytical imprecision was indicated in the determination of two of the five National Water Quality Laboratory nutrient constituents: orthophosphate as phosphorus and phosphorus. A negative or positive bias condition was indicated in three of five nutrient constituents. There was acceptable precision and no indication of bias for the 14 low ionic-strength analytical procedures tested in the National Water Quality Laboratory program and for the 32 inorganic and 5 nutrient analytical procedures tested in the Quality of Water Service Unit during water year 1991.

Water-Resources Investigations Report↗