Bathymetry and capacity of Chambers Lake, Chester County, Pennsylvania

Matthew C. Gyves

doi:10.3133/sim3346

Home/Archive/USGS

USGS · sim3346

Bathymetry and capacity of Chambers Lake, Chester County, Pennsylvania

Matthew C. Gyves

View original source ↗Read source document ↗Export metadata ↓

Abstract

Introduction Chambers Lake is a manmade reservoir on Birch Run, a tributary to West Branch Brandywine Creek in Chester County, Pennsylvania. The lake was created in 1994 after the completion of Multi-Purpose Dam PA-436F (Hibernia Dam), which was built under the Watershed Protection & Flood Control Prevention Act (U.S. Soil Conservation Service, 1991). Hibernia dam is 1,700 feet upstream from the confluence of Birch Run with West Branch Brandywine Creek. The primary objectives for Hibernia Dam were to provide (1) flood control, (2) a supplemental source of water supply for the greater City of Coatesville public water system, and (3) recreational opportunities. The drainage basin of Chambers Lake encompasses approximately 4.5 square miles, and the lake covers a surface area of about 95 acres at normal pool, which is at an elevation of 579.2 feet above the North American Vertical Datum of 1988 (NAVD 88) [580.0 feet above the National Geodetic Vertical Datum of 1929 (NGVD 29)]. The crest of the auxiliary spillway of the dam is 586.6 feet above NAVD 88. The elevation of the auxiliary spillway is important to this investigation because this elevation defines the flood storage capacity of Chambers Lake. Water levels exceeding this elevation are routed through the auxiliary spillway and flow through adjoining woodland to Birch Run. The U.S. Geological Survey (USGS), in cooperation with Chester County Water Resources Authority (CCWRA) and the County of Chester, surveyed the bathymetry and selected above-water features of Chambers Lake in September 2014. The purpose of the survey was to develop an accurate representation of the surface of the bottom of Chambers Lake and to determine the stage area and reservoir-storage capacity relation as of September 2014. CCWRA is responsible for operation of the dam and water-supply reservoir. Since construction, CCWRA has used a stage–storage capacity relation developed from the original survey conducted in the 1990s to estimate the volume of water available for water supply and the available flood storage. The bathymetric mapping effort was initiated due to interest in potential changes in current (2014) storage capacity when compared to the stage–storage capacity relation developed during design. The generated bathymetric surface may serve as a baseline to which temporal changes in storage capacity, owing to sedimentation and other factors, can be compared. In addition, these data will improve the overall accuracy of the stage–storage capacity table that CCWRA uses for reservoir and flood management operations. This report describes the methods used to create a bathymetric map of Chambers Lake for the computation of reservoir storage capacity as of September 2014. The product is a bathymetric map and a table showing the storage capacity of the reservoir at 2-foot increments from minimum usable elevation up to full capacity at the crest of the auxiliary spillway.

Explore related subjects

Scientific Investigations Map Report

Source-reported bounding extent: 40.02781160777367° to 40.03622367578228° latitude; -75.86523056030273° to -75.84815025329588° longitude. This indicates report coverage, not an exact sampling location. View area on OpenStreetMap.

Keep this discovery

Explore connections, maps & timelines

BibTeX RIS

Matthew C. Gyves. 2015-10-26. Bathymetry and capacity of Chambers Lake, Chester County, Pennsylvania. https://doi.org/10.3133/sim3346

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related USGS reports

USGS2026

Altitude of the potentiometric surface and depth to water in the Mississippi River Valley alluvial aquifer, spring 2024

Potentiometric-surface and depth-to-water maps for spring 2024 were created for the Mississippi River Valley alluvial aquifer using groundwater-altitude data from 1,151 wells completed in the Mississippi River Valley alluvial aquifer and from the altitude of the top of the water surface in area rivers from 160 U.S. Geological Survey and U.S. Army Corps of Engineers streamgages. The potentiometric-surface and depth-to-water maps for 2024 were created to support investigations to characterize the Mississippi River Valley alluvial aquifer as part of the U.S. Geological Survey Water Availability and Use Science Program. Sufficient data were available to map the potentiometric surface and depth to water of the Mississippi River Valley alluvial aquifer for spring 2024 for about 83 percent of the aquifer area. The potentiometric contours ranged from 0 to 330 feet (ft) above the North American Vertical Datum of 1988. The regional direction of the groundwater gradient was generally to the south-southwest, except in areas of groundwater-altitude depressions, where the groundwater gradient direction was into the depression, and near rivers, where the groundwater gradient direction was either from the aquifer to the river or from the river into the aquifer. Groundwater depressions in the potentiometric-surface map are in the lower one-half of the Cache region and in most of the Grand Prairie and Delta regions. Depth to water by well in the Mississippi River Valley alluvial aquifer in spring 2024 ranged from 0.27 ft above land surface to 145.65 ft below land surface.

Arkansas, Illinois, Kentucky, Louisiana, Mississip↗

USGS2026

Color-Shaded Relief Bathymetry of Lake Chelan, Washington

In 2023, the U.S. Geological Survey (USGS) completed a 3-week field operation in Lake Chelan, Washington, the third deepest lake in the conterminous United States, to acquire sediment cores, high-resolution bathymetry data, and chirp sub-bottom profiles. The high-resolution bathymetry displayed in this map publication was collected using a Norbit Winghead i67-curved array multibeam system; raw data were cleaned and gridded (3 by 3 meters [m]) in the Teledyne CARIS software. In some locations where the slopes of Lake Chelan are near-vertical, multibeam returns were sparse, resulting in artifacts resembling holes that appear as grey dots within the color-shaded bathymetric relief. Although the 2023 bathymetric mapping of Lake Chelan resulted in similar morphometric characteristics to previous hydrographic campaigns (table 1; Kendra and Singleton, 1987; Pelletier and others, 1989), these new data provide a much more detailed understanding of the two physiographic basins that comprise Lake Chelan: the deeper (as deep as 445.8 m [fig. 1]; previously reported as 453 m) and narrower (1–2 kilometers [km] wide) Lucerne Basin to the north, and the shallower (as deep as 127.8 m [fig. 1]), and wider (2–3 km wide) Wapato Basin to the south. With this detailed imaging of Lake Chelan, we find pervasive morphological evidence of slope failure and mass-transport deposits (MTDs) in at least 89 locations within the lake and 63 subaqueous deltas (fig. 2). The deeper Lucerne Basin is dominated by steep slopes and numerous subaqueous deltas fed by steep fluvial catchments, whereas the Wapato Basin contains numerous landslide scarps, scars, and debris aprons along the more gently sloping lake margins, and abundant relict kettle structures from the Pleistocene deglaciation. Lake Chelan’s geomorphic, geophysical, and sediment data contain important records of glacial retreat and advance, regional volcanic eruptions, and earthquakes that generate ground motions severe enough to induce landslides recorded in the sediment as MTDs. The epicenter of the 1872 Washington State Earthquake (M 6.5–7.2; Bakun and others, 2002; Brocher and others, 2017; Sherrod and others, 2021) is along the Spencer Canyon Fault, near the southern end of Lake Chelan. Shaking from this earthquake was strong enough to affect local aquifers, induce liquefaction of unconsolidated sediments, produce large seiches (Brocher and others, 2018), and likely cause landslides within Lake Chelan.

Washington↗

USGS2026

Spectral characteristics and mapping of lithium-rich playas in the Basin and Range Province, western United States

This report presents a comprehensive set of prospectivity maps for lithium in brines located within the playas of the Basin and Range Province of western United States. The prospectivity assessment is based on criteria established in the descriptive deposit model outlined in a previous U.S. Geological Survey report, with a focus on regional remote sensing methodologies. The playas within the study area have been systematically ranked according to several key factors, including size, the presence and abundance of source rocks, vegetation as an indicator of water availability, documented prospects, and data products derived from the Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) sensor. Notably, the deposits in the playa of Clayton Valley make it stand out as the sole lithium brine-producing playa in the United States. The ASTER sensor provides optimal regional coverage, characterized by a 60-kilometer swath width and unique multispectral capabilities that are not available with other remote sensing instruments. This report and the accompanying maps are intended to serve as resources for further multidisciplinary assessments of lithium or other elements or commodities where prospectivity can be inferred from the presence of proxies such as alteration minerals.

Arizona, Baja California, California, Chihuahua, I↗