Search USGS⌕ Search

USGS · b1082G

Areal geology of the Little Cone quadrangle, Colorado

Abstract

The Little Cone quadrangle includes an area of about 59 square miles in eastern San Miguel County in southwestern Colorado. The quadrangle contains features characteristic of both the Colorado Plateaus physiographic province and the San Juan Mountains, and it has been affected by geologic events and processes of two different geologic environments. The continental sedimentary rocks of the Cutler formation of Permian age are the oldest rocks exposed in the quadrangle. Deposition of the Cutler was followed by a long period of erosion and peneplanation. There is no marked angular discordance between the Cutler and the overlying Dolores formation in the Little Cone quadrangle, but there is in areas some tens of miles east and west of the quadrangle where some crustal warping took place. The continental sedimentary rocks of the Dolores formation of Late Triassic age are red beds that are similar in gross lithology to those of the Cutler. The Dolores formation is subdivided into five general units that persist throughout the quadrangle and for some tens of miles to the north, south, and east. A second long period of erosion followed deposition of the Dolores. The Entrada sandstone of Late Jurassic age overlies the Dolores formation, and is in turn overlain by the Wanakah formation, also of Late Jurassic age. The Wanakah consists of the Pony Express limestone member at the base, the Bilk Creek sandstone'member near the center, and a "marl" member at the top. The Morrison formation, which overlies the Wanakah, consists of the Salt Wash sandstone member in the lower part and the Brushy Basin shale member in the upper part. A period of erosion, probably of relatively short duration, followed deposition of the Brushy Basin member. The Burro Canyon formation of Early Cretaceous age occurs as discontinuous bodies that fill channels cut in the top of the Morrison formation. Deposition of the Burro Canyon formation was followed by another period of erosion, which in turn ended with deposition of the Dakota sandstone of Late Cretaceous age. The Dakota sandstone grades upward into the Mancos shale, also of Late Cretaceous age. The Paleozoic and Mesozoic formations were broadly folded during Laramide time as part of an orogeny of regional extent, and the San Juan Mountains area was uplifted as a broad dome. Extensive erosion followed deformation, and the Cretaceous rocks in the area of the Little Cone quadrangle and the Mesozoic and Paleozoic rocks eastward from the quadrangle were successively bevelled. The Telluride conglomerate of Oligocene(?) age was laid down on this surface. In the Little Cone quadrangle several hundred feet of the Telluride was deposited upon a considerable thickness (probably 3,000 feet or more) of the Mancos shale. At Telluride, about 12 miles east of the quadrangle, the Telluride conglomerate lies upon the Dolores formation. Volcanic rocks of Miocene (?) and Miocene age were deposited widely upon the Telluride conglomerate; at one time they had a thickness of probably 1,000 feet or more in the quadrangle. They have been eroded completely from the quadrangle, but are present in the San Miguel Mountains a few miles to the south and southeast. During the middle Tertiary, probably during the Miocene, the sedimentary rocks were cut by many igneous bodies. Four major rock types are represented; in decreasing order of abundance they are granogabbro, granodidrite, rhyolite(?), and microgabbro. The granogabbro is by far the most abundant, and it forms the Flat Top Peak plug, the Little Cone laccolith, several sills in the Dakota sandstone and the Mancos shale, and a few dikes. The granodiorite forms sills in the Dakota sandstone and the Mancos shale, and the rhyolite(?) forms a single major sill in the Dakota. The microgabbro forms dikes that cut rocks as young as the Mancos shale. Metamorphic effects adjacent to the intrusive bodies generally are restricted to baking that extends only a few feet out into the enclosing rocks; in many places no metamorphic effects are evident. The rocks in the Little Cone quadrangle were displaced along numerous faults in middle Tertiary time, probably after the igneous rocks were injected. All of the faults are normal, and have vertical or very steep dips. In part, the faults form two long and narrow northward- and northwestward-trending grabens that extend into the adjoining Placerville quadrangle to the north. The graben faults form two systems, one trending northward to northwestward, and the other trending northwestward, that are probably contemporaneous. Other faults trend eastward to northeastward; some of these appear to be related to the intrusion of the igneous rocks. At the end of the Tertiary, probably in the early Pleistocene, the general area was again uplifted and subjected to extensive erosion. The Mancos shale was stripped from the northern part of the Little Cone quadrangle, and in this part of the area, the upland surfaces formed on top of the Dakota sandstone were largely controlled by the geologic structure. During the Quaternary a basalt flow was erupted on Specie Mesa on a surface that cuts both the Mancos and the Dakota. The surface preserved beneath the flow has virtually the same position and slope as the adjacent present-day surfaces. Pleistocene deposits consist of (a) high-level or older drift that is unrelated to the present drainage systems and is correlated with the Cerro glacial stage of early Pleistocene age, and (b) younger drift and valley fill within the valleys of the present drainage systems that are correlated with the Durango or Wisconsin glacial stages and may represent both. Recent surficial, landslide, and spring deposits are also present. Within the Little Cone quadrangle and in the Placerville quadrangle to the north and the Gray Head quadrangle to the east, the Entrada sandstone of Late Jurassic age contains vanadium deposits with which are associated large but low-grade amounts of uranium. These deposits form a practically continuous layer about 10 miles long and 1 to 1% miles wide, and possibly a second layer of smaller dimensions. Placer gold deposits in terrace gravel and valley fill of Pleistocene age and in alluvium of Recent age contain the only other ores.

Explore related subjects

90° N90° S · 180° W ← longitude → 180° E
Source-reported bounding extent: 37.875° to 38° latitude; -108.125° to -108° longitude. This indicates report coverage, not an exact sampling location. View area on OpenStreetMap.

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

A.L. Bush, O.T. Marsh, R. B. Taylor. 1960. Areal geology of the Little Cone quadrangle, Colorado. https://doi.org/10.3133/b1082g

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related USGS reports

Groundwater flow model for the Little Plover River basin in Wisconsin’s Central Sands

The Little Plover River is a groundwater-fed stream in the sand plains region of central Wisconsin. In this region, sandy sediment deposited during or soon after the last glaciation forms an important unconfined sand and gravel aquifer. This aquifer supplies water for numerous high-capacity irrigation, municipal, and industrial wells that support a thriving agricultural industry. In recent years the addition of many new wells, combined with observed diminished flows in the Little Plover and other nearby rivers, has raised concerns about the impacts of the wells on groundwater levels and on water levels and flows in nearby lakes, streams, and wetlands. Diverse stakeholder groups, including well operators, Growers, environmentalists, local land owners, and regulatory and government officials have sought a better understanding of the local groundwater-surface water system and have a shared desire to balance the water needs of the he liagricultural, industrial, and urban users with the maintenance and protection of groundwater-dependent natural resources. To help address these issues, the Wisconsin Department of Natural Resources requested that the Wisconsin Geological and Natural History Survey and U.S. Geological Survey cooperatively develop a groundwater flow model that could be used to demonstrate the relationships among groundwater, surface water, and well withdrawals and also be a tool for testing and evaluating alternative water management strategies for the central sands region. Because of an abundance of previous studies, data availability, local interest, and existing regulatory constraints the model focuses on the Little Plover River watershed, but the modeling methodology developed during this study can apply to much of the larger central sands of Wisconsin. The Little Plover River groundwater flow model simulates three-dimensional groundwater movement in and around the Little Plover River basin under steady-state and transient conditions. This model explicitly includes all high-capacity wells in the model domain and simulates seasonal variations in recharge and well pumping. The model represents the Little Plover River, and other significant streams and drainage ditches in the model domain, as fully connected to the groundwater system, computes stream base flow resulting from groundwater discharge, and routes the flow along the stream channel. A separate soil-water-balance (SWB) model was used to develop groundwater recharge arrays as input for the groundwater flow model. The SWB model uses topography, soils, land use, and climatic data to estimate recharge as deep drainage from the soil zone. The SWB model explicitly includes recharge originating as irrigation water, and computes irrigation using techniques similar to those used by local irrigation operators. The groundwater flow model uses the U.S. Geological Survey’s MODFLOW modeling code which is freely available, widely accepted, and commonly used by the groundwater community. The groundwater flow model and the SWB model use identical high-resolution numerical grids having model cells 100 feet on a side, with physical properties assigned to each grid cell. This grid allows accurate geographic placement of wells, streams, and other model features. The 3-dimensional grid has three layers; layers 1 and 2 represent the sand and gravel aquifer and layer 3 represents the underlying sandstone. The distribution of material properties in the model (hydraulic conductivity, aquifer thickness, etc.) comes from previous published geologic studies of the region, updated by calibration to recent streamflow and groundwater level data. The SWB model operates on a daily time step. The groundwater flow model was calibrated to monthly stress periods with time steps ranging from 1 to 16 days. More detailed time discretization is possible. The groundwater model was calibrated to water-level and streamflow data collected during 2013 and 2014 by adjusting model parameters (primarily hydraulic conductivity, storage, and recharge) until the model produced a conditionally optimal fit between field observations and model output, subject to consistency with previously published geologic studies. Calibration was performed under both steady and transient conditions, and used a sophisticated parameter-estimation procedure (PEST) for the calibration process and to identify important model parameters. For the Little Plover River, the two most important parameters are the global recharge multiplier and the hydraulic conductivity of the stream bed. The calibrated model produces water-level and mass-balance results that are consistent with field observations and previous studies of the area. The completed model is a powerful tool for testing and demonstrating alternative water-management scenarios. Example model applications described in this report include simulating how the cumulative impacts of pumping and land-use change have affected average baseflow in the Little Plover River. Depletion-potential mapping represents a method for predicting which wells and well locations have the greatest impact on nearby surface-water resources. The completed model is publicly available, along with a companion user’s guide to assist with its operation, at http://wgnhs.org/littleplover- river-groundwater-model.

Wisconsin↗

The 2016 groundwater flow model for Dane County, Wisconsin

A new groundwater flow model for Dane County, Wisconsin, replaces an earlier model developed in the 1990s by the Wisconsin Geological and Natural History Survey (WGNHS) and the U.S. Geological Survey (USGS). This modeling study was conducted cooperatively by the WGNHS and the USGS with funding from the Capital Area Regional Planning Commission (CARPC). Although the overall conceptual model of the groundwater system remains largely unchanged, the incorporation of newly acquired high-quality datasets, recent research findings, and improved modeling and calibration techniques have led to the development of a more detailed and sophisticated model representation of the groundwater system. The new model is three-dimensional and transient, and conceptualizes the county’s hydrogeology as a 12-layer system including all major unlithified and bedrock hydrostratigraphic units and two high-conductivity horizontal fracture zones. Beginning from the surface down, the model represents the unlithified deposits as two distinct model layers (1 and 2). A single layer (3) simulates the Ordovician sandstone and dolomite of the Sinnipee, Ancell, and Prairie du Chien Groups. Sandstone of the Jordan Formation (layer 4) and silty dolostone of the St. Lawrence Formation (layer 5) each comprise separate model layers. The underlying glauconitic sandstone of the Tunnel City Group makes up three distinct layers: an upper aquifer (layer 6), a fracture feature (layer 7), and a lower aquifer (layer 8). The fracture layer represents a network of horizontal bedding-plane fractures that serve as a preferential pathway for groundwater flow. The model simulates the sandstone of the Wonewoc Formation as an upper aquifer (layer 9) with a bedding-plane fracture feature (layer 10) at its base. The Eau Claire aquitard (layer 11) includes shale beds within the upper portion of the Eau Claire Formation. This layer, along with overlying bedrock units, is mostly absent in the preglacially eroded valleys along the Yahara River valley and in northeastern Dane County. Layer 12 represents the Mount Simon sandstone as the lowermost model layer. It directly overlies the Precambrian crystalline basement rock, whose top surface forms the lower boundary of the model. The model uses the USGS MODFLOW-NWT finite-difference code, a standalone version of MODFLOW-2005 that incorporates the Newton (NWT) solver. MODFLOW-NWT improves the handling of unconfined conditions by smoothing the transition from wet to dry cells. The model explicitly simulates groundwater–surface-water interaction with streamflow routing and lake-level fluctuation. Model input included published and unpublished hydrogeologic data from recent estimates of aquifer hydraulic conductivities. A spatial groundwater recharge distribution was obtained from a recent GIS-based, soil-water-balance model for Dane County. Groundwater withdrawals from pumping were simulated for 572 wells across the entire model domain, which includes Dane County and portions of seven neighboring counties—Columbia, Dodge, Green, Iowa, Jefferson, Lafayette, and Rock. These wells withdrew an average of 60 million gallons per day (mgd) over the 5-year period from 2006 through 2010. Within Dane County, 385 wells were simulated with an average withdrawal rate of 52 mgd. Model calibration used the parameter estimation code PEST, and calibration targets included heads, stream and spring flows, lake levels, and borehole flows. Steady-state calibration focused on the period 2006 through 2010; the transient calibration focused on the 7-week drought period from late May through July 2012. This model represents a significant step forward from previous work because of its finer grid resolution, improved hydrostratigraphic discretization, transient capabilities, and more sophisticated representation of surface-water features and multi-aquifer wells. Potential applications of the model include evaluation of potential sites for and impacts of new high-capacity wells, development of wellhead protection plans, evaluating the effects of changing land use and climate on groundwater, and quantifying the relationships between groundwater and surface water.

Wisconsin↗

Geologic framework of the Alaska Peninsula, southwest Alaska, and the Alaska Peninsula terrane

The Alaska Peninsula is composed of the late Paleozoic to Quaternary sedimentary, igneous, and minor metamorphic rocks that record the history of a number of magmatic arcs. These magmatic arcs include an unnamed Late Triassic(?) and Early Jurassic island arc, the early Cenozoic Meshik arc, and the late Cenozoic Aleutian arc. Also found on the Alaska Peninsula is one of the most complete nonmetamorphosed, fossiliferous, marine Jurassic sedimentary sections known. As much as 8,500 m of section of Mesozoic sedimentary rocks record the growth and erosion of the Early Jurassic island arc. A thinner, but still thick (as much as 5,400 m), sequence of Tertiary sedimentary rocks that are predominantly continental overlies the Mesozoic section. A brief regression in early Tertiary time on the Alaska Peninsula and granodiorite plutonism in the Shumagin, Semidi, and Sanak Islands was followed by deposition of fluvial and minor marine clastic strata. This was followed by deposition of transgressive marine clastic strata and initiation of the Meshik arc, shown by an areally extensive outpouring of volcanic and volcaniclastic rocks and debris between late Eocene and earliest Miocene time. Late Miocene time was marked by another brief transgression and northwest- to southeast-directed compression, followed by renewed volcanism and plutonism which initiated the modern Aleutian magmatic arc. Extensive glacial and glaciomarine deposits of late Pleistocene age create an extensive lowland physiographic province on the northwest side of the Alaska Peninsula and join isolated mountain masses to the Alaska Peninsula on the southwest. Multiple active volcanoes and volcanic peaks dominate the skyline of the Alaska Peninsula and represent the continuation of magmatic activity that has formed the Aleutian arc since late Miocene time. The Alaska Peninsula has had a long and involved history since Paleozoic time. We propose that the Paleozoic and Mesozoic rocks that constitute much of the Alaska Peninsula be called the Alaska Peninsula terrane. Using the concept of subterranes, we divide the terrane into two distinct but tectonically related subterranes: the Chignik and Iliamna subterranes, which share a limited common geologic history. The Iliamna subterrane has served at most times as a source area for the Chignik subterrane; however, some rock units are in common across the subterranes. The Iliamna and Chignik subterranes are in part separated by the Bruin Bay fault system. The Iliamna subterrane is composed of moderately deformed early Mesozoic marine sedimentary and volcanic rocks and schist, gneiss, and marble of Paleozoic(?) and Mesozoic age, and plutonic rocks of the Alaska-Aleutian Range batholith. Characteristic of the Chignik subterrane are little-deformed, shallow-marine to continental clastic sedimentary rocks ranging in age from Permian to latest Cretaceous. However, deep-marine, volcaniclastic, and calcareous rocks form important components of the older rocks in the subterrane. The two subterranes of the Alaska Peninsula terrane are characterized by radically different structural and metamorphic styles. The nonplutonic rocks of the Iliamna subterrane are characterized by metamorphism up to amphibolite-facies grade and intense folding. In the Chignik subterrane, the structural style is dominated by large, open, en echelon anticlinal structures, normal faulting, and thrust and high-angle reverse faults that have minor displacement in a northwest to southeast direction. In the Outer Shumagin and Sanak Islands, rocks assigned to the Chugach terrane are characterized structurally by tight, generally northeast-trending folds. Dips in these rocks tend to be steep, rarely less than 35°, and overturned beds are locally common. The boundaries separating the Alaska Peninsula terrane from other terranes are commonly indistinct or poorly defined. A few boundaries have been defined at major faults, although the extensions of these faults are speculative through some areas. The west side of the Alaska Peninsula terrane is overlapped by Tertiary sedimentary and volcanic rocks and Quaternary deposits.

Alaska↗