Search USGS⌕ Search
Home/Archive/USGS

USGS · 70277739

Velocity-independent dry friction on mica: A realization of ideal Amontons-Coulomb friction

Hiroshi Sakuma·Diane E. Moore·David A. Lockner·Toshihiro Kogure
View original source ↗Export metadata ↓

Abstract

The Amontons-Coulomb friction law assumes that the frictional force between materials is independent of sliding velocity. However, as Coulomb noted, this is a rough approximation, and a second-order dependence of friction on the logarithm of sliding velocity is incorporated in a commonly used ‘rate- and state-dependent’ friction representation. Here we conduct shear experiments on mica, a layer-structured mineral, at temperatures ranging from 25 to 200ºC and under normal stress of 100 MPa. The friction coefficient clearly depends on the logarithmic sliding velocity at 25ºC, but rate sensitivity decreases with increasing temperature until at 200ºC, the friction coefficient is independent of sliding velocity. Our findings could initiate the development of velocity-independent frictional materials, realizing the ideal Amontons-Coulomb friction.

Explore related subjects

Physical Review LettersArticle

Keep this discovery

BibTeXRIS

Hiroshi Sakuma, Diane E. Moore, David A. Lockner, Toshihiro Kogure. 2026-07-20. Velocity-independent dry friction on mica: A realization of ideal Amontons-Coulomb friction. https://doi.org/10.1103/y3jy-nqcd

Cite the original work for its findings. Save a collection to share your selection of sources.

Discover connections

Article subjectPhysical Review Letters subject

Connections use source metadata and explicit phrase matches, not verified experimental comparisons.

KEEP EXPLORING

Related USGS reports

USGS2025

High-pass corner frequency selection and review tool for use in ground-motion processing

Raw seismological waveform data contain noise from the instrument’s surroundings and the instrument itself that can dominate recordings at low and high frequencies. To use these data in ground‐motion modeling, the effects of noise on the signals must be reduced and the signals’ usable frequency range identified. We present automated procedures to efficiently reduce low‐frequency noise that are implemented in the software package gmprocess. These procedures check for, and as needed remove, low‐frequency artifacts in the displacement record using polynomial fits, which can be used in combination with existing signal‐to‐noise ratio (SNR)‐based corner‐frequency selection procedures. The automated selections are then efficiently verified and refined using a graphical user interface (GUI) that plots relevant ground‐motion time series and spectra and tracks modifications to signal processing parameters. We demonstrate these procedures using recordings from the 2020 M 5.1 Sparta, North Carolina, and the 2013 M 4.7 southern Ontario earthquakes. Data processed with the SNR‐only and polynomial criteria for these events contain displacement artifacts in 37% and 23% of processed traces, respectively. Records with remaining artifacts are corrected manually using the GUI. These processing steps illustrate the workflow for efficient data processing with quality control.

Seismological Research Letters↗
USGS2025

Deterministic physics-based earthquake sequence simulators match empirical ground-motion models and enable extrapolation to data poor regimes: Application to multifault multimechanism ruptures

We use the deterministic earthquake simulator RSQSim to generate complex sequences of ruptures on fault systems used for hazard assessment. We show that the source motions combined with a wave propagation code create surface ground motions that fall within the range of epistemic uncertainties for the Next Generation Attenuation‐West2 set of empirical models. We show the model is well calibrated where there are good data constraints, and has good correspondence in regions with fewer data constraints. We show magnitude, distance, and mechanism dependence all arising naturally from the same underlying friction. The deterministic physics‐based approach provides an opportunity for better understanding the physical origins of ground motions. For example, we find that reduced stress drops in shallow layers relative to constant stress drop with depth lead to peak ground velocities in the near field that better match empirical models. The simulators may also provide better extrapolations into regimes that are poorly empirically constrained by data because physics, rather than surface shaking data parameterizations, is underlying the extrapolations. Having shown the model is credible, we apply it to a problem where observations are lacking. We examine the case of crustal faults above a shallow subduction interface seen to break coseismically in simulations of the New Zealand fault system. These types of events were left out of consideration in the most recent New Zealand national seismic hazard model due to the modeling complexity and lack of observational data to constrain ground‐motion models (GMMs). Here, we show that in the model, by breaking up the coseismic crustal and interface rupturing fault motions into two separate subevents, and then recombining the resulting ground‐motion measures in a square‐root‐of‐sum‐of‐squares incoherent manner, we reproduce well the ground‐motion measures from the full event rupture. This provides a new method for extrapolating GMMs to more complex multifault ruptures.

Seismological Research Letters↗
USGS2025

Probing lower-crustal fault properties with frequency-dependent tidal tremor triggering

The way seismicity responds to periodic stress perturbations offers crucial insights into the processes that can trigger an earthquake. Laboratory and theoretical analyses have shown that the period of imposed forcing and source properties affect the sensitivity to triggering, but frequency-dependent triggering of tectonic faults is poorly understood. The rate of low-frequency earthquakes (LFEs) near Parkfield, California has been found to be strongly correlated with solid earth tides. Tidal forcing acts over multiple frequencies, and the sensitivity to tidal triggering of LFEs therefore provides a unique opportunity to probe the physics of earthquake triggering and underlying fault properties. Here, we find that the response of LFEs to solid earth tides at diurnal and semi-diurnal frequencies is highly variable but spatially coherent along the San Andreas Fault. Using rate-state friction modeling, we find that the variation of the amplitude of tidal modulation is mainly affected by the spatial variation of the background effective normal stress, whereas the spatially varied tidal modulation at diurnal and semi-diurnal frequencies is mainly affected by the fault frictional property. The spatial variations of the LFE response reveal a heterogeneous lower-crustal geologic structure and complex physical faulting processes below the rupture zone of eventual great earthquakes.

California↗