Search USGSSearch

USGS · 70254502

Elastic stress coupling between supraglacial lakes

Abstract

Supraglacial lakes have been observed to drain within hours of each other, leading to the hypothesis that stress transmission following one drainage may be sufficient to induce hydro-fracture-driven drainages of other nearby lakes. However, available observations characterizing drainage-induced stress perturbations have been insufficient to evaluate this hypothesis. Here, we use ice-sheet surface-displacement observations from a dense global positioning system array deployed in the Greenland Ice Sheet ablation zone to investigate elastic stress transmission between three neighboring supraglacial lake basins. We find that drainage of a central lake can place neighboring basins in either tensional or compressional stress relative to their hydro-fracture scarp orientations, either promoting or inhibiting hydro-fracture initiation beneath those lakes. For two lakes located within our array that drain close in time, we identify tensional surface stresses caused by ice-sheet uplift due to basal-cavity opening as the physical explanation for these lakes' temporally clustered hydro-fracture-driven drainages and frequent triggering behavior. However, lake-drainage-induced stresses in the up-flowline direction remain low beyond the margins of the drained lakes. This short stress-coupling length scale is consistent with idealized lake-drainage scenarios for a range of lake volumes and ice-sheet thicknesses. Thus, on elastic timescales, our observations and idealized-model results support a stress-transmission hypothesis for inducing hydro-fracture-driven drainage of lakes located within the region of basal cavity opening produced by the initial drainage, but refute this hypothesis for distal lakes.

Explore related subjects

90° N90° S · 180° W ← longitude → 180° E
Source-reported bounding extent: 68.6° to 68.8° latitude; -49.75° to -49.25° longitude. This indicates report coverage, not an exact sampling location. View area on OpenStreetMap.

Keep this discovery

BibTeXRIS

L. Stevens, S. Das, M. D. Behn, Jeffrey J. McGuire, Ching-Yao Lai, I. Joughin, S LaRochelle, M. Nettles. 2024-05-10. Elastic stress coupling between supraglacial lakes. https://doi.org/10.1029/2023jf007481

Cite the original work for its findings. Save a collection to share your selection of sources.

Discover connections

Connections use source metadata and explicit phrase matches, not verified experimental comparisons.

KEEP EXPLORING

Related USGS reports

Fully contained laboratory earthquakes: The effect of asperity aspect ratio and free surfaces

Corner frequency ( f c ) and seismic moment ( M 0 ) are key parameters derived from seismic signals that are used to characterize earthquake stress drop, rupture area, and slip. These parameters are also affected by fault geometry and boundary conditions. However, the systematic study of these effects in laboratory settings has been challenging. This study presents laboratory earthquake experiments that examine how rupture dynamics are influenced by (a) the aspect ratio of rectangular PMMA velocity-weakening (VW) asperities surrounded by the Teflon velocity-strengthening (VS) patches, and (b) whether the sides of a VW asperity are confined with VS patches or are free surfaces. We found that increasing confinement by reducing free surfaces or increasing the VW asperity aspect ratio stabilizes fault slip, so that higher normal stress is required to transition from aseismic to seismic slip. Increased confinement and high aspect ratios also reduced M 0 and increased f c , both of which were determined from the radiated seismic waves. M 0 and f c were primarily controlled by the shorter dimension of the VW asperity. Analysis of high-frequency acoustic emission signals revealed that ruptures on high-aspect-ratio VW asperities propagated more unidirectionally, whereas ruptures on square VW asperities were more complex. Further, the high-aspect-ratio asperities were more likely to be eroded by surrounding VS regions while low-aspect-ratio asperities were more likely to rupture into the VS surroundings. These results demonstrate that both the confinement from surrounding stable areas and the geometry of the seismogenic patch can affect rupture nucleation, propagation, and seismic source characteristics.

JGR Solid Earth

Three-dimensional seismic velocity models for the San Francisco Bay region, California from joint body-wave and surface-wave tomography validated by waveform simulation

A high-resolution seismic velocity model for both P and S waves is essential for the San Francisco Bay (SFB) region to accurately simulate earthquake ground motions and assess seismic hazards in this high-risk region. We present new three-dimensional P-wave and S-wave velocity (Vp and Vs) models of the SFB region developed using joint tomographic inversion with a rich set of earthquake and active-source body-wave data and ambient-noise surface-wave data. We designed a dynamic balance strategy to effectively balance the contributions of body-wave and surface-wave data during each iteration of the inversion. Owing to the complementary resolution of body-wave and surface-wave data, our new models are significantly improved compared to previous tomographic models. Major geologic features in the SFB region, including low-velocity basins, high-velocity Franciscan Complex, granite, and gabbro rocks, and across-fault velocity contrasts, are imaged in our Vp and Vs models. Compared to the geology-based U.S. Geological Survey velocity model, our new model has better defined structures for some important areas that are of great concern for seismic hazard assessment, such as the Sacramento-San Joaquin Delta, and the 2014 magnitude 6.0 South Napa earthquake area. We validated our model by simulating waveforms for a set of moderate-magnitude earthquakes. The good performance of our model in waveform simulation indicates its potential for improving ground motion simulation and seismic hazard assessment in the SFB region.

California

Multi-scale geophysical imaging of a hydrothermal system in Yellowstone National Park, USA

Little is known about the local plumbing systems that fuel Yellowstone’s famous hot springs, geysers and mud pots. A multi-method, multi-scale geophysical investigation was carried out in the Obsidian Pool Thermal Area (OPTA) to: (i) delineate the lateral extent of the hydrothermal area and associated surface features; (ii) estimate the dimensions of the upflow zone and identify its main controlling structures; (iii) assess fluids circulation pathways from depth to surface. Ground and airborne geophysical data were acquired to connect local and regional scales, from shallow to large depths. Maps of surface electrical resistivity show a strong correlation with hydrothermal features. At in-termediate depths, electrical resistivity permits delineating the upper limit of the upflow zone, while Poisson’s ratio highlights differences in subsurface fluid content. Combining these results with surface observations and topographic information, we speculate that differential mixing of hydrothermal and fresh water could explain the wide diversity of features observed at OPTA. Low electrical resistivity observed at large depths also suggest that a vast upflow zone, controlled by rhyolite flows and conjugate faults, underlies the OPTA. We speculate that hydrothermal fluids rise along fractures and reach the surface in topographic lows to form hydrothermal features. Our results show that synoptic, multi-scale geophysical measurements provide a roadmap for understanding where and how geologic heterogeneity, topography, fluid-gas separation, and the mixing of thermal and meteoric waters conspire to produce the wide variety of Yellowstone’s renowned hydrothermal features.

Wyoming