Integrated use of surface geophysical methods for site characterization — A case study in North Kingstown, Rhode Island

Carole D. Johnson; John W. Lane; William C. Brandon; Christine A.P. Williams; Eric A. White

doi:10.4133/1.3445441

Home/Archive/USGS

USGS · 70193759

Integrated use of surface geophysical methods for site characterization — A case study in North Kingstown, Rhode Island

Carole D. Johnson·John W. Lane·William C. Brandon·Christine A.P. Williams·Eric A. White

View original source ↗Export metadata ↓

Abstract

A suite of complementary, non‐invasive surface geophysical methods was used to assess their utility for site characterization in a pilot investigation at a former defense site in North Kingstown, Rhode Island. The methods included frequency‐domain electromagnetics (FDEM), ground‐penetrating radar (GPR), electrical resistivity tomography (ERT), and multi‐channel analysis of surface‐wave (MASW) seismic. The results of each method were compared to each other and to drive‐point data from the site. FDEM was used as a reconnaissance method to assess buried utilities and anthropogenic structures; to identify near‐surface changes in water chemistry related to conductive leachate from road‐salt storage; and to investigate a resistive signature possibly caused by groundwater discharge. Shallow anomalies observed in the GPR and ERT data were caused by near‐surface infrastructure and were consistent with anomalies observed in the FDEM data. Several parabolic reflectors were observed in the upper part of the GPR profiles, and a fairly continuous reflector that was interpreted as bedrock could be traced across the lower part of the profiles. MASW seismic data showed a sharp break in shear wave velocity at depth, which was interpreted as the overburden/bedrock interface. The MASW profile indicates the presence of a trough in the bedrock surface in the same location where the ERT data indicate lateral variations in resistivity. Depths to bedrock interpreted from the ERT, MASW, and GPR profiles were similar and consistent with the depths of refusal identified in the direct‐push wells. The interpretations of data collected using the individual methods yielded non‐unique solutions with considerable uncertainty. Integrated interpretation of the electrical, electromagnetic, and seismic geophysical profiles produced a more consistent and unique estimation of depth to bedrock that is consistent with ground‐truth data at the site. This test case shows that using complementary techniques that measure different properties can be more effective for site characterization than a single‐method investigation.

Explore related subjects

Conference Paper

Source-reported bounding extent: 41.48697733905992° to 41.64136125487125° latitude; -71.58176422119139° to -71.40666961669922° longitude. This indicates report coverage, not an exact sampling location. View area on OpenStreetMap.

Keep this discovery

Explore connections, maps & timelines

BibTeX RIS

Carole D. Johnson, John W. Lane, William C. Brandon, Christine A.P. Williams, Eric A. White. 2010-05-17. Integrated use of surface geophysical methods for site characterization — A case study in North Kingstown, Rhode Island. https://doi.org/10.4133/1.3445441

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related USGS reports

USGS2026

Authoritative knowledge infrastructure for GeoAI: Implications for scientific spatial data providers

Geospatial Artificial Intelligence (GeoAI) increasingly relies on automated analysis of authoritative geospatial data, exposing limitations in data infrastructures originally designed for simple dissemination rather than for knowledge-driven use. From the perspective of scientific spatial data providers, the challenge is enabling GeoAI responsibly while retaining semantic clarity, provenance, reproducibility, and governance. This short paper (i) examines how GeoAI exposed limitations within existing geospatial data infrastructures, and (ii) identifies provider-side requirements for an authoritative knowledge infrastructure. Drawing on GIScience, scientific workflow, and operational AI literature, the paper outlines implications for national mapping organizations that seek to support advanced analytics without jeopardizing scientific rigor or stewardship responsibilities.

Conference Paper↗

USGS2026

Springs of the Catskill Mountains: A conduit flow system in predominantly siliciclastic strata

The Catskill Mountains of New York state are composed of thick sequences of interbedded mudstone, sandstone, and siltstone that are intercalated with thin beds of paludal limestone and calcareous mudstone. Sandstones often contain rip-up clasts of calcareous material at their bases and contain minor amounts of carbonate cement throughout their mass. This minor amount of calcareous material weathers out to produce thin zones of solutional porosity and permeability integrated within perched aquifers that feed perennial hillslope springs. Solutional features are evident within thin carbonate lenses and along fractures in sandstones, occasionally resulting in explorable cave-sized conduits. This study focuses on the behavior of bedrock springs and seeps in the headwaters of the Neversink River basin above the Neversink Reservoir. Bedrock springs are numerous throughout the Catskill Mountains and serve to provide baseflow to the headwater streams that tends to be more persistent during dry times than other baseflow sources. We observed dissolution-influenced conduits within the bedrock, and suffosional conduits within unconsolidated materials. Continuous water temperature at six springs was monitored at hourly intervals from May to October 2022 to investigate the thermal response of groundwater to daily and seasonal changes in air temperature along with event-based meteorological events. Temperature monitoring was augmented at some springs with time-lapse photography to evaluate persistence of flow. The thermal responses of springs to precipitation events were highly variable across sites, with some springs exhibiting flashy responses indicating a strong connection to the surface, while other springs showed muted or no thermal response to events. The seasonal thermal response also varied across sites having lag times of 23-48 days between peak air temperature and peak spring water temperature. The water temperatures and geochemical compositions of these bedrock springs support a conceptual model of multiple residence times, showing both event and seasonal groundwater storage within the conduit flow system that feeds the springs of the Catskill Mountains.

New York↗

USGS2026

Stability changes after weak layer collapse: Insights from an unexpected dataset

While conducting avalanche mitigation or traveling through the backcountry, avalanche professionals sometimes experience a "whumpf": a collapse-mode crack accompanied by surface cracking that does not produce an avalanche. These whumpfs are a clear warning sign of instability in the surrounding terrain. But assessing the collapsed slope itself, if it is steep enough to avalanche, carries much more uncertainty. Can slopes that whumpf and are steep enough to slide still avalanche? The answer to this question supports avalanche mitigators and ski guides in assessing whether to open such slopes. Previous research on collapsed slopes is limited to one study conducted before tests that estimate crack propagation propensity, such as the Propagation Saw Test (PST), were developed. This work showed that weak layer shear strength decreased immediately after collapsing and then increased over time. However, no research has examined crack propagation propensity after a whumpf. Studying propagation propensity is key for assessing how whumpfs immediately affect slope stability. To improve our understanding of changes in propagation propensity following weak layer collapse, we conducted PSTs on a test slope in the hours and days after an unexpected collapse occurred on a layer of surface hoar. Two PSTs at our study site three days prior to this collapse provided an estimate of weak layer propagation propensity. PST cut lengths decreased immediately following the collapse, suggesting that the collapse increased the propagation propensity. However, over the next 4-5 hours, PST cut lengths steadily increased at our site, likely due to ongoing sintering and strengthening in the collapsed weak layer. By the end of day two, we were no longer able to initiate propagation, suggesting substantial stabilization of the weak layer. Our results support prior findings and observations suggesting that slopes may remain capable of producing avalanches immediately after a collapse but likely stabilize over the next day or two. Although this research does not provide answers about precisely when a slope becomes stable after a collapse, it does highlight uncertainties in our understanding and interpretation of the stability of slopes that have whumped.

Montana↗