Hydro-bio-geomechanical properties of hydrate-bearing sediments from Nankai Trough

J.C. Santamarina; Shifeng Dai; M. Terzariol; Jeonghwan Jang; William F. Waite; William J. Winters; J. Nagao; J. Yoneda; Y. Konno; T. Fujii; K. Suzuki

doi:10.1016/j.marpetgeo.2015.02.033

USGS · 70190286

Hydro-bio-geomechanical properties of hydrate-bearing sediments from Nankai Trough

J.C. Santamarina·Shifeng Dai·M. Terzariol·Jeonghwan Jang·William F. Waite·William J. Winters·J. Nagao·J. Yoneda·Y. Konno·T. Fujii·K. Suzuki

View original source ↗Export metadata ↓

Abstract

Natural hydrate-bearing sediments from the Nankai Trough, offshore Japan, were studied using the Pressure Core Characterization Tools (PCCTs) to obtain geomechanical, hydrological, electrical, and biological properties under in situ pressure, temperature, and restored effective stress conditions. Measurement results, combined with index-property data and analytical physics-based models, provide unique insight into hydrate-bearing sediments in situ. Tested cores contain some silty-sands, but are predominantly sandy- and clayey-silts. Hydrate saturations S h range from 0.15 to 0.74, with significant concentrations in the silty-sands. Wave velocity and flexible-wall permeameter measurements on never-depressurized pressure-core sediments suggest hydrates in the coarser-grained zones, the silty-sands where S h exceeds 0.4, contribute to soil-skeletal stability and are load-bearing. In the sandy- and clayey-silts, where S h < 0.4, the state of effective stress and stress history are significant factors determining sediment stiffness. Controlled depressurization tests show that hydrate dissociation occurs too quickly to maintain thermodynamic equilibrium, and pressure–temperature conditions track the hydrate stability boundary in pure-water, rather than that in seawater, in spite of both the in situ pore water and the water used to maintain specimen pore pressure prior to dissociation being saline. Hydrate dissociation accompanied with fines migration caused up to 2.4% vertical strain contraction. The first-ever direct shear measurements on never-depressurized pressure-core specimens show hydrate-bearing sediments have higher sediment strength and peak friction angle than post-dissociation sediments, but the residual friction angle remains the same in both cases. Permeability measurements made before and after hydrate dissociation demonstrate that water permeability increases after dissociation, but the gain is limited by the transition from hydrate saturation before dissociation to gas saturation after dissociation. In a proof-of-concept study, sediment microbial communities were successfully extracted and stored under high-pressure, anoxic conditions. Depressurized samples of these extractions were incubated in air, where microbes exhibited temperature-dependent growth rates.

Explore related subjects

Journal of Marine and Petroleum Geology Article

Keep this discovery

Explore connections, maps & timelines

BibTeX RIS

J.C. Santamarina, Shifeng Dai, M. Terzariol, Jeonghwan Jang, William F. Waite, William J. Winters, J. Nagao, J. Yoneda, Y. Konno, T. Fujii, K. Suzuki. 2015. Hydro-bio-geomechanical properties of hydrate-bearing sediments from Nankai Trough. https://doi.org/10.1016/j.marpetgeo.2015.02.033

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related USGS reports

USGS2023

Characterization of a complex sand-rich gas hydrate reservoir system in the Indian marine continental margin with downhole log and seismic data

Logging-while-drilling (LWD) and coring data were acquired in Areas A, B, C and E during the National Gas Hydrate Program Expedition 02 (NGHP-02). At Sites NGHP-02-16, −17, −20, −23 and −24 of Area B in the Indian Krishna-Godavari Basin, the gas hydrate-bearing sand-rich reservoirs directly in contact with an underlying water-saturated sediment were revealed near the seismic-inferred bottom simulating reflector (BSR) along a large anticlinal structure. Lithofacies analysis of cores show that the lower gas hydrate-bearing reservoir section at these sites is an interbedded unit with thin fine-sand layers alternating with clay-rich layers. We reanalyzed the LWD data including resistivity, compressional-wave and shear-wave acoustic velocities to assess and compare the spatial variation of sand-hosted gas hydrate and possible related free-gas accumulations. The presence of free gas-bearing sediments in direct contact with gas hydrate-bearing sediments was confirmed at Sites NGHP-02-20 and −24 along the northeastern flank of the anticline. The sand-rich reservoirs associated with the Area B anticlinal feature reveal different pore-filling constituents and variable boundary conditions, including gas hydrate/water contacts and gas hydrate/free gas contacts. We infer that the sedimentary depositional history at Sites NGHP-02-20 and −24, may have resulted in an upward shift of the base of gas hydrate stability zone, that could have led to in situ gas hydrate dissociation and the accumulation of free gas and coexistence interval below the log-inferred gas hydrate-bearing reservoir sections. This study demonstrates that reservoir heterogeneity and fluid migration were major factors affecting the distribution of gas hydrate and free gas in the identified sand-rich reservoirs.

Journal of Marine and Petroleum Geology↗

USGS2022

Diatom influence on the production characteristics of hydrate-bearing sediments: Examples from Ulleung Basin, offshore South Korea

The Ulleung Basin Gas Hydrate field expeditions in 2007 (UBGH1) and 2010 (UBGH2) sought to assess the Basin's gas hydrate resource potential. Coring operations in both expeditions recovered evidence of gas hydrate, primarily as fracture-filling (or vein type) morphologies in mainly silt-sized, fine-grained sediment, but also as pore-occupying hydrate in the coarser-grained layers of interbedded sand and fine-grained systems. A commonality across many of these occurrences is the presence of diatoms in the fine-grained sediment. Here we tested fine-grained sediment (median grain size <12.5 μm) associated with hydrate occurrences at four UBGH2 sites (UBGH2-2-2, UBGH2-3, UBGH2-6 and UBGH2-11) to investigate potential impacts of diatoms on efforts to extract methane from hydrate, or to tap hydrocarbon reservoirs beneath hydrate-bearing sediment. Two key considerations are: the extent to which diatoms control sediment mechanical properties, and the extent to which pore-water freshening, which occurs as gas hydrate breaks down during resource extraction, alters the diatom control on sediment mechanical properties. We conducted experiments to measure sediment index properties, sedimentation behavior and compressibility to address these considerations. We relied on scanning electron microscope (SEM) imagery and X-ray powder diffraction (XRD) to characterize the sediment mineralogy. Our high-level findings are that at the ∼20–45% (by volume) diatom concentrations observed at these UBGH2 sites, sediment compressibility increases with diatom content, but diatoms only appear to increase porosity and permeability at the highest diatom concentration (∼45%). Our measurements suggest in situ compression indices of 0.35–0.55 and permeabilities on the order of 0.01milliDarcies (1 × 10 −17 m 2 ) can be anticipated at these sites. Importantly, these properties are not expected to vary significantly upon pore water freshening that accompanies gas hydrate dissociation during production.

East Sea, Ulleung Basin↗

USGS2021

Multiple physical properties of gas hydrate-bearing sediments recovered from Alaska North Slope 2018 Hydrate-01 Stratigraphic Test Well

Knowledge of the petrophysical and geomechanical properties of gas hydrate-bearing sediments is essential for predicting reservoir responses to gas production from gas hydrate reservoirs. In December 2018, Stratigraphic Test Well Hydrate-01 was drilled in the western part of the Prudhoe Bay Unit, Alaska North Slope, as part of the technical planning effort for a future long-term gas hydrate production test. Side-wall pressure coring was conducted to recover gas hydrate-bearing sediments from two reservoir sections named Unit B and Unit D. A total of 34 cores were successfully recovered during five runs of a wireline deployed pressure corer, and a total of 17 cores were preserved for advanced laboratory analysis. The samples were frozen inside the pressure core autoclave by liquid nitrogen while at high pressure before being removed and stored under liquid nitrogen at atmospheric pressure. High-resolution X-ray computed tomography showed the samples were high-quality, with undisturbed lithological layers. The Unit B and D sediments were categorized as sand or sandy silt with high hydrate saturation. Gas compositions suggest the hydrates formed with thermogenic and microbial mixed gases. Permeability tests and triaxial compression tests were conducted on the hydrate-bearing sediments. Low strengthening and high permeability at hydrate saturation S h > 80% were observed. There was a small permeability reduction during the triaxial compression tests owing to porosity loss with increasing effective stress in the highly permeable sandy sediment after hydrate dissociation. The apparent minimal changes in porosity and permeability during the tests were due to the low-clay content and low compressibility of the quartz sand grains in the recovered cores. X-ray powder diffraction and thermal conductivity analysis also suggested a high quartz content for the analyzed samples.

Alaska↗