Search USGSSearch

USGS · 70185383

Chemical and isotopic methods for quantifying ground-water recharge in a regional, semiarid environment

Abstract

The High Plains aquifer underlying the semiarid Southern High Plains of Texas and New Mexico, USA was used to illustrate solute and isotopic methods for evaluating recharge fluxes, runoff, and spatial and temporal distribution of recharge. The chloride mass-balance method can provide, under certain conditions, a time-integrated technique for evaluation of recharge flux to regional aquifers that is independent of physical parameters. Applying this method to the High Plains aquifer of the Southern High Plains suggests that recharge flux is approximately 2% of precipitation, or approximately 11 ± 2 mm/y, consistent with previous estimates based on a variety of physically based measurements. The method is useful because long-term average precipitation and chloride concentrations in rain and ground water have less uncertainty and are generally less expensive to acquire than physically based parameters commonly used in analyzing recharge. Spatial and temporal distribution of recharge was evaluated by use of δ 2 H, δ 18 O, and tritium concentrations in both ground water and the unsaturated zone. Analyses suggest that nearly half of the recharge to the Southern High Plains occurs as piston flow through playa basin floors that occupy approximately 6% of the area, and that macropore recharge may be important in the remaining recharge. Tritium and chloride concentrations in the unsaturated zone were used in a new equation developed to quantify runoff. Using this equation and data from a representative basin, runoff was found to be 24 ± 3 mm/y; that is in close agreement with values obtained from water-balance measurements on experimental watersheds in the area. Such geochemical estimates are possible because tritium is used to calculate a recharge flux that is independent of precipitation and runoff, whereas recharge flux based on chloride concentration in the unsaturated zone is dependent upon the amount of runoff. The difference between these two estimates yields the amount of runoff to the basin.

Explore related subjects

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

Warren W. Wood, Ward E. Sanford. 2005-08-04. Chemical and isotopic methods for quantifying ground-water recharge in a regional, semiarid environment. https://doi.org/10.1111/j.1745-6584.1995.tb00302.x

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related USGS reports

Computing flow-field distortion coefficients from well-construction and formation properties

Direct measurements of groundwater velocity made with borehole flowmeters in screened wells must be compensated for the effects of flow-field distortion (also known as borehole acceleration). A theoretical equation developed by Drost et al. (1968) and simple inputs describing hydraulic properties of well construction and geologic formation were programmed into an Excel workbook to facilitate computation by groundwater-flowmeter users. Tables describing the physical and hydraulic properties for well constructions and gravel pack media are provided with an example to facilitate use of the workbook. Groundwater flowlines converge or diverge as they pass from a geologic formation, through a gravel pack and well screen. The extent of flowline convergence or divergence and the value of the flow-field distortion coefficient is related to the relative changes in hydraulic conductivity of the well screen, gravel pack, and geologic formation. Convergence or divergence is accompanied by acceleration or deceleration of groundwater. Direct measurements of groundwater velocity at the center of the monitoring well can be adjusted to provide a more accurate estimate of velocity in the formation by applying a correction for flow-field distortion. Variables required to compute the flow-field distortion coefficient include the hydraulic conductivity of the gravel pack, well screen, and the geologic formation surrounding the well screen; the borehole radius, and the inside radius and outside radius of the well screen.

Groundwater

Deep groundwater total dissolved solids mapping in the Dakota Group, Williston Basin, USA

Growing concern about the quantity of available freshwater around the world has led to interest in surveying groundwater total dissolved solids (TDS) below water well depths. Deep TDS has not been systematically mapped, and there is much to learn about the distribution and controls on deeper groundwater. In sedimentary basins across the United States, groundwater resources often overlie hydrocarbon resources, providing an opportunity to use borehole geophysical data collected for hydrocarbons to characterize groundwater and pore space resources. This study adapts a recently developed subsurface geostatistical and geophysical modeling approach to continuously map groundwater TDS, porosity, and temperature in the Dakota Group of the Williston Basin—an undercharacterized regional aquifer system overlying deeper hydrocarbon reservoirs. Groundwater TDS in the Dakota Group ranges from approximately 4800 to 26,900 mg/L. TDS patterns are stratified with higher TDS in the lower and upper Dakota Group, and relatively lower TDS in the middle Dakota Group. The lower TDS in the middle zone may represent a preferential regional flow path for lower-TDS meteoric recharge from the west. The alternating pattern of TDS may also be evidence of higher-TDS inflows into the Dakota Group from underlying and potentially from overlying aquifers. Porosity is lower near the center of the Williston Basin and tends to be higher to the east, which may be related to grain size distributions. The new regional TDS and porosity modeling serves as a quantitative reference for water users and provides supporting evidence for hypotheses on Dakota Group recharge.

Montana, North Dakota, South Dakota