Search USGSSearch

USGS · 70027292

Microforms in gravel bed rivers: Formation, disintegration, and effects on bedload transport

Abstract

This research aims to advance current knowledge on cluster formation and evolution by tackling some of the aspects associated with cluster microtopography and the effects of clusters on bedload transport. The specific objectives of the study are (1) to identify the bed shear stress range in which clusters form and disintegrate, (2) to quantitatively describe the spacing characteristics and orientation of clusters with respect to flow characteristics, (3) to quantify the effects clusters have on the mean bedload rate, and (4) to assess the effects of clusters on the pulsating nature of bedload. In order to meet the objectives of this study, two main experimental scenarios, namely, Test Series A and B (20 experiments overall) are considered in a laboratory flume under well-controlled conditions. Series A tests are performed to address objectives (1) and (2) while Series B is designed to meet objectives (3) and (4). Results show that cluster microforms develop in uniform sediment at 1.25 to 2 times the Shields parameter of an individual particle and start disintegrating at about 2.25 times the Shields parameter. It is found that during an unsteady flow event, effects of clusters on bedload transport rate can be classified in three different phases: a sink phase where clusters absorb incoming sediment, a neutral phase where clusters do not affect bedload, and a source phase where clusters release particles. Clusters also increase the magnitude of the fluctuations in bedload transport rate, showing that clusters amplify the unsteady nature of bedload transport. A fourth-order autoregressive, autoregressive integrated moving average model is employed to describe the time series of bedload and provide a predictive formula for predicting bedload at different periods. Finally, a change-point analysis enhanced with a binary segmentation procedure is performed to identify the abrupt changes in the bedload statistic characteristics due to the effects of clusters and detect the different phases in bedload time series using probability theory. The analysis verifies the experimental findings that three phases are detected in the bedload rate time series structure, namely, sink, neutral, and source. ?? ASCE / JUNE 2004.

Explore related subjects

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

K. Strom, A.N. Papanicolaou, N. Evangelopoulos, M. Odeh. 2004. Microforms in gravel bed rivers: Formation, disintegration, and effects on bedload transport. https://doi.org/10.1061/(asce)0733-9429(2004)130%3A6(554)

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related USGS reports

Discharge estimation using video recordings from small unoccupied aircraft systems

Measurement of river discharge during flooding events has especially been a challenging and dangerous task in the southwestern US, where flows can be flashy, laden with sediment, and at high velocity. Small unoccupied aircraft systems (sUAS) can be deployed to access unsafe field sites and capture imagery for measuring surface flow velocity and discharge. This paper compares flow discharge estimation at eight field sites—located at or near USGS gauging stations—using time-averaged surface velocities and the turbulence dissipation rate (TDR) derived from large-scale particle image velocimetry (LSPIV) analysis of sUAS videos with conventional measurement techniques conducted by professional USGS hydrographers. Sites characteristics include both natural and engineered channels. The conventional measured discharges were treated as the reference discharges for evaluating the accuracy of the LSPIV discharge estimates. This study evaluated four approaches to estimate the depth-averaged or cross-sectional averaged velocity: constant-velocity index, logarithmic law, power-law, and the entropy method. Results showed the discharges can be accurately calculated by using any of these methods, and that choice of method depended on width to depth ratios.

Journal of Hydraulic Engineering

Dynamic selection of exposure time for turbulent flow measurements

The selection of optimum sampling configurations to measure the aspects of turbulent flow of water depends on the variable being measured, the applied measurement technique, the degree of environmental noise, and flow characteristics in and near the sampling location. This work presents a method to dynamically select the exposure time (SET) during the flow-velocity measurement at each sampling location on the basis of the moving block bootstrap (MBB) technique. The MBB enables near real-time estimation of the confidence intervals and, subsequently, the COV for turbulence parameters. The dynamic SET method has been tested in this work using time series of synthetic turbulent flow-velocity signals. This method was implemented using actual flow-velocity signals recorded with acoustic Doppler velocity (ADVs) instruments and acoustic Doppler current profilers (ADCPs). The results obtained from the implementation of the dynamic SET method show that the sampling time to achieve a defined uncertainty threshold is not the same for different turbulence parameters. Consequently, using the dynamic SET method, the exposure time can be optimized to obtain the turbulence parameters with the required uncertainty level. The dynamic SET method can be implemented in the instrument’s data logger to dynamically select the exposure time during flow measurements for a given uncertainty of the required turbulence parameter.

Journal of Hydraulic Engineering

Effectiveness of submerged vanes for stabilizing streamside bluffs

The effectiveness of submerged vanes for stabilizing streamside bluffs varied over a 10-year monitoring period in a tributary to Lake Superior, United States. Submerged vanes are a river training device used to divert river flows away from eroding banks along meander bends and ultimately hold constant or reverse the direction of lateral migration. At the study site, the relatively steep slope, large substrate size, and flashy flow regime pushed the upper end of the design limitations of submerged vanes. Changes in channel location and morphology due to the vanes were monitored using repeat channel cross-section surveys along a 110-m reach. The vanes experienced 15 floods over the monitoring period. The two most damaging floods happened in the summer and fall of 2005 with annual exceedance probabilities of 7% and 6% respectively. A new data analysis method for rivers, using centroids of cross sections, was useful to track channel migration rapidly and objectively and, along with calculations of changes in bankfull channel size, provide metrics to describe channel change.

Journal of Hydraulic Engineering