Search USGS⌕ Search
Home/Archive/USGS

USGS · 70019918

Adsorbed natural gas storage with activated carbons made from Illinois coals and scrap tires

Jielun Sun·T.A. Brady·M.J. Rood·C.M. Lehmann·M. Rostam-Abadi·A.A. Lizzio
View original source ↗Export metadata ↓

Abstract

Activated carbons for natural gas storage were produced from Illinois bituminous coals (IBC-102 and IBC-106) and scrap tires by physical activation with steam or CO 2 and by chemical activation with KOH, H 3 PO 4 , or ZnCl 2 . The products were characterized for N 2 -BET area, micropore volume, bulk density, pore size distribution, and volumetric methane storage capacity ( V m / V s ). V m / V s values for Illinois coal-derived carbons ranged from 54 to 83 cm 3 /cm 3 , which are 35−55% of a target value of 150 cm 3 /cm 3 . Both granular and pelletized carbons made with preoxidized Illinois coal gave higher micropore volumes and larger V m / V s values than those made without preoxidation. This confirmed that preoxidation is a desirable step in the production of carbons from caking materials. Pelletization of preoxidized IBC-106 coal, followed by steam activation, resulted in the highest V m / V s value. With roughly the same micropore volume, pelletization alone increased V m / V s of coal carbon by 10%. Tire-derived carbons had V m / V s values ranging from 44 to 53 cm 3 /cm 3 , lower than those of coal carbons due to their lower bulk densities. Pelletization of the tire carbons increased bulk density up to 160%. However, this increase was offset by a decrease in micropore volume of the pelletized materials, presumably due to the pellet binder. As a result, V m / V s values were about the same for granular and pelletized tire carbons. Compared with coal carbons, tire carbons had a higher percentage of mesopores and macropores.

Explore related subjects

Energy and FuelsArticle

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

Jielun Sun, T.A. Brady, M.J. Rood, C.M. Lehmann, M. Rostam-Abadi, A.A. Lizzio. 1997-03-19. Adsorbed natural gas storage with activated carbons made from Illinois coals and scrap tires. https://doi.org/10.1021/ef960201h

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related USGS reports

USGS2026

Lithological control of gas hydrate saturation determined by pressure core analysis in sub-permafrost reservoirs of the Alaska North Slope (HYDRATE 02 Geo Data Well)

Quantitatively degassing pressure cores by controlled depressurization is a key approach to characterizing gas hydrate reservoirs by measuring the gas hydrate saturation (S h ) of sediments. We measured S h for 53 core sections from the Alaska North Slope during the JOGMEC-DOE-USGS Collaborative Gas Hydrate R&D Project in Alaska, from subpermafrost sediments that were later subjected to an extended-duration gas production test. We characterized lithologic influences on S h using physical property core scans (P-wave velocity, gamma ray attenuation density, and X-ray computed tomography) and grain size measurements. Pressure cores were recovered from the Hydrate-02 Geo Data Well (GDW) at the Kuparuk State 7-11-12 site through two hydrate-bearing sand reservoirs, the B1 and D1 sands, and their finer-grained bounding sediments. S h reaches very high values (68 to 91% of the pore space) in silty fine sands within the B1 sand, which also contains two lower P-wave velocity intervals (one measured at 30% S h ) within the main reservoir. S h and grain sizes of the B1 sand are generally higher than the D1 sand, which hosts high S h (53 to 73%) within its sandy silt to silty fine sands. The heterogeneous silty clay to silt “seal” sediments directly overlying both reservoirs have low S h (0 to 13%) even in thin, coarser beds, suggesting minimal methane transport between the reservoir and seal. S h decreases with depth downward toward the base of both the D1 and B1 sands, corresponding to decreasing grain size. These transitions are underlain by silty clay to clayey silt sediments with low S h (<10%), similar to the seal sediments. Slow depressurization was used to estimate a brackish salinity based on the pressure and temperature of the onset of hydrate dissociation for two core sections within the B1 sand. We show that S h increases with median grain size, sand content, and porosity but exhibits some variation within the sand beds that is not directly explained by lithology.

Alaska↗
USGS2024

3-D geological modeling for numerical flow simulation studies of gas hydrate reservoirs at the Kuparuk State 7-11-12 Pad in the Prudhoe Bay Unit on the Alaska North Slope

Accurate reservoir evaluation requires reliable three-dimensional (3-D) geological models. This study conducted 3-D geological modeling for numerical flow simulation of the B1 sand gas hydrate reservoir at the Kuparuk State 7-11-12 pad, Prudhoe Bay Unit, Alaska North Slope. The model integrates well logs, core, and seismic data to address spatial heterogeneity in geological structures and reservoir properties. Two modeling types were performed: structural framework modeling and petrophysical property modeling. For structural framework modeling, seismic data and well log markers were used to reproduce subsurface structures characterized by a normal fault system. A volume-based modeling algorithm and stair-step gridding were applied. The resulting 3-D model comprised 2,640,000 grid cells across 264 layers, including seven fault grids. For petrophysical property modeling, total porosity was initially modeled using sequential Gaussian simulation with collocated cokriging. To reproduce the upward coarsening of the B1 sand, upscaled log-derived total porosity and a 3-D trend depicting total porosity variation were used as primary and secondary data, respectively. Gas hydrate saturation distribution was modeled similarly, with secondary data from estimated porosity distribution and seismic-derived acoustic impedance map enhancing accuracy. Results indicate higher gas hydrate saturation in the upper part of the B1 sand and areas with higher acoustic impedance. Intrinsic permeability was modeled from the total porosity and clay-bound water volume, and effective permeability was derived from the gas hydrate saturation and intrinsic permeability distributions based on the “Tokyo model”. Effective permeability distributions were influenced by the total porosity, gas hydrate saturation, and intrinsic permeability. Within the same layer, higher gas hydrate saturation leads to decreased effective permeability. In total, 100 sets of multiple scenarios were prepared, providing input data for dynamic flow simulations to evaluate the effects of lateral heterogeneity in reservoir properties and the hydraulic characteristics of faults on production behavior for preassessment before the long-term production test.

Alaska↗
USGS2020

Nanoscale molecular composition of solid bitumen from the Eagle Ford Group across a natural thermal maturity gradient

Microscopic solid bitumen is a petrographically defined secondary organic matter residue produced during petroleum generation and subsequent oil transformation. The presence of solid bitumen impacts many reservoir properties including porosity, permeability, and hydrocarbon generation and storage, among others. Furthermore, solid bitumen reflectance is an important parameter for assessing the thermal maturity of formations with little to no vitrinite. While the molecular composition of solid bitumen will strongly impact associated parameters such as the development of organic matter porosity, hydrocarbon generation, and optical reflectance, assessing the molecular composition of solid bitumen in situ within shale reservoirs can be challenging due to the small grain sizes (often ≤1 μm in diameter) and the inherent heterogeneity of shale formations. Here we employ the recently developed atomic force microscopy based infrared spectroscopy (AFM-IR) technique to investigate solid bitumen molecular composition in situ within shale samples from the Late Cretaceous Eagle Ford Group. These samples possess sulfur-rich type II kerogens that span a natural thermal maturity gradient from early oil generation to the dry gas window. The application of AFM-IR allows for the rapid collection of thousands of compositional measurements from solid bitumen with ∼50 nm resolution. Our results indicate that (i) solid bitumen from the lower Eagle Ford displays both intra- and intergranular variation in the relative abundance of CH 2 , C═C, and C═O moieties present; (ii) this molecular variation tends to, but does not always, decrease with an increase in thermal maturity; and (iii) the solid bitumen composition between samples, from an atomic ratio perspective, is more similar than analysis of bulk kerogen isolates would indicate. These findings are discussed with perspective toward understanding the impact of thermal stress on the composition of secondary organic matter within the Eagle Ford Shale and highlight the growing awareness that organic matter heterogeneity within petroliferous mudrocks extends down to the nanoscale regime.

Energy and Fuels↗