Characteristics of faults and shear zones in deep mines

R. E. Wallace; H. T. Morris

doi:10.1007/bf00875721

Home/Archive/USGS

USGS · 70014911

Characteristics of faults and shear zones in deep mines

R. E. Wallace·H. T. Morris

View original source ↗Export metadata ↓

Abstract

The characteristics of fault and shear zones to depths of 2.5 km are well documented in deep mines in North America. The characteristics may be summarized as follows. (a) Fault zones usually are irregular, branched, anastomosed, and curved rather than simple and planar. (b) Faults are generally composed of one or more clay or clay-like gouge zones in a matrix of sheared and foliated rock bordered by highly fractured rock. (c) The widths of fault zones appear to be greater when faults have greater displacement, probably as a result of a long history of repeated minor movements. Fault zones with kilometers of displacement tend to be 100 m or more wide, whereas those with only a few hundred meters of displacement commonly are only 1 m or less wide. (d) Some zones represent shear distributed across hundreds of meters without local concentration in a narrow gouge zone. (e) Many fault zones are wet even above the water table, and water moves along them at various rates, but some also serve as subsurface dams, ponding ground water as much as several hundred meters higher on one side than on the other. No striking differences in the characteristics of faults over the vertical range of 2.5 km are documented. ?? 1986 Birkha??user Verlag.

Explore related subjects

Pure and Applied Geophysics PAGEOPH Article

Keep this discovery

Explore connections, maps & timelines

BibTeX RIS

R. E. Wallace, H. T. Morris. 1986. Characteristics of faults and shear zones in deep mines. https://doi.org/10.1007/bf00875721

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related USGS reports

USGS2016

Introduction to “Global tsunami science: Past and future, Volume I”

Twenty-five papers on the study of tsunamis are included in Volume I of the PAGEOPH topical issue “Global Tsunami Science: Past and Future”. Six papers examine various aspects of tsunami probability and uncertainty analysis related to hazard assessment. Three papers relate to deterministic hazard and risk assessment. Five more papers present new methods for tsunami warning and detection. Six papers describe new methods for modeling tsunami hydrodynamics. Two papers investigate tsunamis generated by non-seismic sources: landslides and meteorological disturbances. The final three papers describe important case studies of recent and historical events. Collectively, this volume highlights contemporary trends in global tsunami research, both fundamental and applied toward hazard assessment and mitigation.

Pure and Applied Geophysics PAGEOPH↗

USGS1995

Implications of Coulomb plasticity for the velocity dependence of experimental faults

Simulated fault gouges often deform more stably than initially bare surfaces of the same composition. It is important to understand why the sliding stability is enhanced because the presence of gouge on natural faults may have the same effect as seen in experiments, and thus explain the absence of earthquakes at shallow depths. Gouge stabilization in experiments has been attributed to positive contributions to velocity dependence within gouge layers from either dilation (Maroneet al., 1990) or grain fracture (Biegelet al., 1989). In this study we test the hypothesis that some aspects of gouge and initially bare surface velocity dependence are identical by measuring the time-dependent constitutive parameter b. An important result follows however from stress analysis: if both sample configurations are frictional in the Mohr-Coulomb sense, each configuration is required to deform on planes of distinctly different orientation. The measured strength and velocity dependence will reflect this geometric difference. Our observed values of b for simulated granite and quartz gouge are two to two and a half times smaller than b for initially bare surfaces. This difference is completely accounted for if gouge is represented as a cohesionless-Coulomb plastic material. The analysis demonstrates the following points: 1) gouge deformation is fully consistent with Coulomb plasticity, 2) observed gouge velocity dependence is a function of observed strength and 3) the constitutive parameter b is the same for both bare surfaces and gouge. Furthermore, the results suggest that there is no time-dependent strengthening associated with stabilizing effects in gouge. These observations provide a framework for understanding how slip on initially bare surfaces and gouge deformation are related. ?? 1995 Birkha??user Verlag.

Pure and Applied Geophysics PAGEOPH↗

USGS1995

The effect of fault-bend folding on seismic velocity in the marginal ridge of accretionary prisms

Fluid venting in accretionary prisms, which feeds chemosynthetic biological communities, occurs mostly on the marginal thrust ridge. New seismic data for the marginal ridge of the Cascadia prism show significantly lower velocity than that in the adjacent oceanic basin and place important constraints on the interpretations of why fluid venting occurs mostly on the marginal ridge. We employed a finite-element method to analyze a typical fault-bend folding model to explain the phenomenon. The fault in the model is simulated by contact elements. The elements are characterized not only by finite sliding along a slide line, but also by elastoplastic deformation. We present the results of a stress analysis which show that the marginal ridge is under subhorizontal extension and the frontal thrust is under compression. This state of stress favors the growth of tensile cracks in the marginal ridge, facilitates fluid flow and reduces seismic velocities therein; on the other hand, it may close fluid pathways along the frontal thrust and divert fluid flow to the marginal ridge. ?? 1995 Birkha??user Verlag.

Pure and Applied Geophysics PAGEOPH↗