Search USGS⌕ Search

USGS · 70014687

Piston core properties and disturbance effects.

Abstract

Laboratory geotechnical data on piston cores for 31 sites on the mid-Atlantic Upper Continental Slope show the near-surface sediments vary from normally consolidated to somewhat overconsolidated clayey silts and silty clays of low to high plasticity. They also exhibit normalized behavior and their index property correlations with the effective-stress friction angle, the undrained strength ratio, and the compression index are reasonably consistent with existing knowledge. Because existing knowledge concerning disturbance effect suggests that in-situ preconsolidation stress values should lie between those derived from the triaxial and laboratory vane data, the preconsolidation stress values obtained from the consolidation data appear to be appreciably smaller than in-situ values. -from ASCE Publications Information

Explore related subjects

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

H. W. Olsen, T. L. Rice, P. W. Mayne, R.D. Singh. 1986. Piston core properties and disturbance effects.. https://doi.org/10.1061/(asce)0733-9410(1986)112%3A6(608)

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related USGS reports

Piezometer performance at Wildlife liquefaction site, California

In response to an urgent need for field data from instrumented liquefaction sites, the U.S. Geological Survey in 1982 selected and instrumented a site in southern California called the Wildlife site. Two accelerometers (one at ground surface and one at a depth of 7.5 m) and six electrical pore‐pressure transducers (five in a liquefiable silty sand layer) were placed at the site. The November 1987 Superstition Hills earthquake triggered sand boils and the desired instrumental response by generating excess pore‐water pressure that approximately equaled the initial effective overburden pressure. These records are the first from a field site to trace ground motions and pore pressures through the entire liquefaction process. Because pore pressure continued to rise after most of the seismic energy had propagated through the site, questions about the fidelity of the pore‐pressure records have been raised. Because of the importance of the Wildlife records, we reexamine pertinent aspects of the instruments and their placement, review their 1987 response, evaluate and respond to criticisms by Hushmand et al. (1992a, 1992b), and examine analyses of the records by other investigators that are pertinent to an evaluation of the fidelity of the piezometer records. This review concludes that no data or analyses have been developed that convincingly demonstrate that the pore‐pressure piezometers responded incorrectly. Conversely, an analysis by Zeghal and Elgamal (1994) provides strong evidence that the piezometers responded with a high degree of fidelity.

California↗

Potential for seepage erosion of landslide dam

The failure potential of the debris-avalanche dam at Castle Lake near Mount St. Helens, Washington, by three processes of seepage erosion (1) Heave; (2) piping; and (3) internal erosion, is examined. Results indicated that the dam is stable against piping but potentially locally unstable against heave. -from Authors

Journal of Geotechnical Engineering↗

Sensitive strata in Bootlegger Cove Formation

Sensitivity magnitudes are interpreted from remolded strength values in recent subsurface geologic, geotechnical, and geochemical data from the Bootlegger Cove Formation adjacent to the Turnagain Heights Landslide. The results show that strata composed of highly sensitive clays occur in both the middle and lower zones of the formation, and that between these strata the clays are generally of low-to-medium sensitivity. The most sensitive stratum is in the middle zone between two sand layers, and its sensitivity increases from both clay-sand interfaces to a maximum at the center of the stratum. The pore fluid chemistry of the highly sensitive materials differs from that in the materials of low to medium sensitivity only in their concentrations of organic carbon, chloride, bicarbonate, and sulfate. The total dissolved solids concentration is low, and the ratio of monovalent to divalent cations is very high throughout the middle and lower zones of the formation. Of the known causes of high and extremely high sensitivities, only organic and/or anionic dispersants are consistent with these findings.

Journal of Geotechnical Engineering↗