Static and kinetic friction of granite at high normal stress

J.D. Byerlee

doi:10.1016/0148-9062(70)90018-5

Home/Archive/USGS

USGS · 70010188

Static and kinetic friction of granite at high normal stress

J.D. Byerlee

View original source ↗Export metadata ↓

Abstract

Frictional sliding on ground surfaces of granite, angle of sliding planes 30° and 45°, was investigated as a function of confining pressure. Over the normal stress range of 2–12 kb, the static frictional shear stress τ s follows the relationship τ s = 0·5 + 0· σ n and the kinetic frictional shear stress τ k was calculated to be τ k = 0·25 + 0·47 σ n .

Explore related subjects

International Journal of Rock Mechanics and Mining Sciences & Geomechanics Abstracts Article

Keep this discovery

Explore connections, maps & timelines

BibTeX RIS

J.D. Byerlee. 1970. Static and kinetic friction of granite at high normal stress. https://doi.org/10.1016/0148-9062(70)90018-5

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related USGS reports

USGS1997

Dual-porosity analysis of conservative tracer testing in saturated volcanic rocks at Yucca Mountain in Nye County, Nevada

A radially convergent conservative tracer injection test was conducted between boreholes UE-25 #2 and UE-25 c #3 of the C-hole complex at Yucca Mountain to determine effective porosity and longitudinal dispersivity. Approximately 47% of the tracer mass was recovered and a dual-porosity analytical model replicates the breakthrough curve. Fractured-rock analyses focus on the fracture-porosity and geometry as the controlling factors in transport.

International Journal of Rock Mechanics and Mining↗

USGS1997

Borehole sampling of fracture populations - compensating for borehole sampling bias in crystalline bedrock aquifers, Mirror Lake, Grafton County, New Hampshire

The clustering of orientations of hydraulically conductive fractures in bedrock at the Mirror Lake, New Hampshire fractured rock study site was investigated by comparing the orientations of fracture populations in two subvertical borehole arrays with those mapped on four adjacent subvertical roadcuts. In the boreholes and the roadcuts, the orientation of fracture populations appears very similar after borehole data are compensated for undersampling of steeply dipping fractures. Compensated borehole and pavement fracture data indicate a northeast-striking population of fractures with varying dips concentrated near that of the local foliation in the adjacent rock. The data show no correlation between fracture density (fractures/linear meter) and distance from lithologic contacts in both the boreholes and the roadcuts. The population of water-producing borehole fractures is too small (28 out of 610 fractures) to yield meaningful orientation comparisons. However, the orientation of large aperture fractures (which contains all the producing fractures) contains two or three subsidiary clusters in orientation frequency that are not evident in stereographic projections of the entire population containing all aperture sizes. Further, these subsidiary orientation clusters do not coincide with the dominant (subhorizontal and subvertical) regional fracture orientations.

International Journal of Rock Mechanics and Mining↗

USGS1994

Gravitational stresses in long symmetric ridges and valleys in anisotropic rock

The effect of topography and rock mass anisotropy on gravitational stresses in long isolated symmetric ridges and valleys is modeled using an analytical method proposed earlier by the first two authors. The rock mass deforms under a condition of plane strain. A parametric study is presented on the effect of (1) topography, (2) orientation of anisotropy and (3) degree of anisotropy on the magnitude and distribution of gravitational stresses in transversely isotropic rock masses with planes of anisotropy striking parallel to the ridge or valley axis. It is found that compressive stresses develop near ridge crests and that tensile stresses develop in valley bottoms and valley walls. The magnitude of the gravitational stresses is of the order of the characteristics stress ??{variant}g??b?? where ??{variant} is the rock density, g is the gravitational acceleration and ??b?? is the height of the ridge or depth of the valley. ?? 1994.

International Journal of Rock Mechanics and Mining↗