Search USGS⌕ Search

Geology topics

Research about Red River Valley

Source-linked reports with geographic coverage including Red River Valley.

10 recordsLinked to original sources
USGS2008

Questa baseline and pre-mining ground-water quality investigation. 17. Geomorphology of the Red River Valley, Taos County, New Mexico, and influence on ground-water flow in the shallow alluvial aquifer

In April 2001, the U.S. Geological Survey (USGS) and the New Mexico Environment Department (NMED) began a cooperative study to infer the pre-mining ground-water chemistry at the Molycorp molybdenum mine site in the Red River Valley of north-central New Mexico. This report is one in a series of reports that can be used to determine pre-mining ground-water conditions at the mine site. Molycorp’s Questa molybdenum mine in the Red River Valley, northern New Mexico, is located near the margin of the Questa caldera in a highly mineralized region. The bedrock of the Taos Range surrounding the Red River is composed of Proterozoic rocks of various types, which are intruded and overlain by Oligocene volcanic rocks associated with the Questa caldera. Locally, these rocks were altered by hydrothermal activity. The alteration zones that contain sulfide minerals are particularly important because they constitute the commercial ore bodies of the region and, where exposed to weathering, form sites of rapid erosion referred to as alteration scars. Over the past thousand years, if not over the entire Holocene, erosion rates were spatially variable. Forested hillslopes eroded at about 0.04 millimeter per year, whereas alteration scars eroded at about 2.7 millimeters per year. The erosion rate of the alteration scars is unusually rapid for naturally occurring sites that have not been disturbed by humans. Watersheds containing large alteration scars delivered more sediment to the Red River Valley than the Red River could remove. Consequently, large debris fans, as much as 80 meters thick, developed within the valley. The geomorphology of the Red River Valley has had several large influences on the hydrology of the shallow alluvial aquifer, and those influences were in effect before the onset of mining within the watershed. Several reaches where alluvial ground water emerges to become Red River streamflow were observed by a tracer dilution study conducted in 2001. The aquifer narrows where erosion-resistant bedrock, which tends to form vertical cliffs, restricts the width of the valley bottom. Although the presence of a shallow bedrock sill, overlain by shallow alluvium, is a plausible cause of ground-water emergence, this cause was not demonstrated in the study area. The water-table gradient can locally decrease in the downstream direction because of changes in the hydraulic properties of the alluvium, and this may be a contributing cause of ground-water emergence. However, at one site (near Cabin Springs), ground-water emergence could not be explained by spatial changes in geometric or hydraulic properties of the aquifer. Furthermore, the available evidence demonstrates that ground water flowing through bedrock fractures or colluvium entered the north side of the alluvial aquifer, and is the cause of ground-water emergence. At that location the alluvial aquifer was already flowing full, causing the excess water to emerge into the stream. An indirect consequence of altered rock in the tributary watersheds is the rapid erosion rate of alteration scars combined with the hydraulic properties of sediments shed from those scars. Where alteration scars are large the debris fans at the mouths of the tributary watersheds substantially encroach into the Red River Valley. At such locations debris-fan materials dominate the width and thickness of the alluvium in the valley and reduce the rate of flow of ground water within the Red River alluvial aquifer. Most sites of groundwater emergence are located immediately upstream from or along the margins of debris fans. A substantial fraction of the ground water approaching a debris fan can emerge to become streamflow. This last observation has three implications. First, very little water can flow the entire length of the study area entirely within the alluvial aquifer because the ground water repeatedly contacts debris-fan sediments over that length. Second, it follows that emerging water containing unique elemental constituents must have entered the alluvial aquifer at a relatively short distance upstream. Third, a gravel aquifer downstream from a large debris fan can transmit more ground water than flows into it through the debris fan. This observation explains how the water table can be naturally, and permanently, located well beneath the level of the bed of a perennial stream.

New Mexico↗
USGS2007

Questa baseline and pre-mining ground-water quality investigation 15.—Methods of phase II and III well installation and development and results of well logging, hydraulic testing, and water-level measurements in the Red River Valley, New Mexico, 2002-04

In April 2001, the U.S. Geological Survey and the New Mexico Environment Department began a cooperative study to infer the pre-mining ground-water chemistry at the Molycorp molybdenum mine site in the Red River Valley of north- central New Mexico. This report is one in a series of reports that can be used to determine pre-mining ground-water conditions at the mine site. Weathering of hydrothermally altered bedrock in the study area has resulted in steep, highly erosive, and sparsely vegetated scar areas that are clearly visible from the ground and in aerial photographs. Runoff from intense summer rainfall over tributary drainages containing scar areas can transport large quantities of sediment and form debris fans where these tributaries join the Red River. Twenty-nine observation wells were installed in three phases as part of this study in the Red River Valley and tributary drainages. Eight Phase II observation wells were drilled using an air-rotary/hammer rig. Three Phase II and 10 phase III small-diameter wells were installed using a direct-push rig. Lithologic logs were recorded for all eight Phase II drilled wells. Borehole geophysical logging (including natural gamma, induction, and single-detector neutron) was conducted in three Phase II wells. Aquifer tests conducted during 2003 to estimate the hydraulic properties of debris-flow and Red River alluvial deposits in and near Straight Creek included a flow-meter survey, slug tests, and a pumping test. Results of a flow-meter survey in well SC-7A indicated that about 77 percent of the water entered the well from a 10-foot-thick zone near the top of the screened interval and about 23 percent of the water entered the well from a 15-foot-thick zone near the bottom of the screened interval. Slug tests, performed in 11 wells during June 3-5, 2003, indicated that the mean and median estimated hydraulic conductivities for debris-flow deposits were 15.25 and 15.35 feet per day, respectively, for bedrock were 0.12 and 0.08 feet per day, respectively, and for mixed debris flow and Red River alluvium were 73-207 (estimated range) and 80 feet per day. In general, bedrock has the smallest hydraulic conductivity, debris-flow material has the next highest hydraulic conductivity, and mixed debris flow and Red River alluvium has the largest hydraulic conductivity. A pumping test conducted December 3-4, 2003, using well AWWT-1 as the pumped well, and wells AWWT-2, SC-5A, SC-5B, SC-7A, and SC-8A as observation wells, indicated estimated transmissivity of 12,000 to 34,000 feet squared per day and estimated hydraulic conductivity of 230 to 340 feet per day. Water-level measurements in wells SC-6A, SC-7A, SC-8A, and the Hottentot, Hansen, and La Bobita wells show that water levels typically rose rapidly during melting of the winter snowpack in the springtime and then generally declined during the rest of the year. The water-level rise in response to spring snowmelt occurred earlier and was smaller at larger distances from the Red River. Differences between the stage in the Red River and water levels in wells SC-8A and SC-9A, and the absence of water in well SC-9A at the time of well completion, indicate that the Red River has a poor hydraulic connection to the underlying ground-water system and the surface-water system is perched above the ground-water system at this site. Water levels in Phase III wells indicate that the Red River and the shallow ground-water system are connected hydraulically from near wells 4-1D and 4-1S downstream to near wells 2-1 and 2-2 but are poorly connected near the La Bobita well and well 1.

New Mexico↗
USGS2005

Questa baseline and pre-mining ground-water quality investigation. 5. Well installation, water-level data, and surface- and ground-water geochemistry in the Straight Creek drainage basin, Red River Valley, New Mexico, 2001-03

The U.S. Geological Survey, in cooperation with the New Mexico Environment Department, is investigating the pre-mining ground-water chemistry at the Molycorp molybdenum mine in the Red River Valley, northern New Mexico. The primary approach is to determine the processes controlling ground-water chemistry at an unmined, off-site, proximal analog. The Straight Creek drainage basin, chosen for this purpose, consists of the same quartz-sericite-pyrite altered andesitic and rhyolitic volcanic rock of Tertiary age as the mine site. The weathered and rugged volcanic bedrock surface is overlain by heterogeneous debris-flow deposits that interfinger with alluvial deposits near the confluence of Straight Creek and the Red River. Pyritized rock in the upper part of the drainage basin is the source of acid rock drainage (pH 2.8-3.3) that infiltrates debris-flow deposits containing acidic ground water (pH 3.0-4.0) and bedrock containing water of circumneutral pH values (5.6-7.7). Eleven observation wells were installed in the Straight Creek drainage basin. The wells were completed in debris-flow deposits, bedrock, and interfingering debris-flow and Red River alluvial deposits. Chemical analyses of ground water from these wells, combined with chemical analyses of surface water, water-level data, and lithologic and geophysical logs, provided information used to develop an understanding of the processes contributing to the chemistry of ground water in the Straight Creek drainage basin. Surface- and ground-water samples were routinely collected for determination of total major cations and selected trace metals; dissolved major cations, selected trace metals, and rare-earth elements; anions and alkalinity; and dissolved-iron species. Rare-earth elements were determined on selected samples only. Samples were collected for determination of dissolved organic carbon, mercury, sulfur isotopic composition (34S and 18O of sulfate), and water isotopic composition (2H and 18O) during selected samplings. One set of ground-water samples was collected for helium-3/tritium and chlorofluorocarbon (CFC) age dating. Several lines of evidence indicate that surface water is the primary input to the Straight Creek ground-water system. Straight Creek streamflow and water levels in wells closest to the apex of the Straight Creek debris fan and closest to Straight Creek itself appear to respond to the same seasonal inputs. Oxygen and hydrogen isotopic compositions in Straight Creek surface water and ground water are similar, and concentrations of most dissolved constituents in most Straight Creek surface-water and shallow (debris-flow and alluvial) aquifer ground-water samples correlate strongly with sulfate (concentrations decrease linearly with sulfate in a downgradient direction). After infiltration of surface water, dilution along the flow path is the dominant mechanism controlling ground-water chemistry. However, concentrations of some constituents can be higher in ground water than can be accounted for by concentrations in Straight Creek surface water, and additional sources of these constituents must therefore be inferred. Constituents for which concentrations in ground water can be high relative to surface water include calcium, magnesium, strontium, silica, sodium, and potassium in ground water from debris-flow and alluvial aquifers and manganese, calcium, magnesium, strontium, sodium, and potassium in ground water from the bedrock aquifer. All ground water is a calcium sulfate type, often at or near gypsum saturation because of abundant gypsum in the aquifer material developed from co-existing calcite and pyrite mineralization. Calcite dissolution, the major buffering mechanism for bedrock aquifer ground water, also contributes to relatively higher calcium concentrations in some ground water. The main source of the second most abundant cation, magnesium, is probably dissolution of magnesium-rich carbonates or silicates.

New Mexico↗
USGS2004

Questa baseline and pre-mining ground-water quality investigation 4. Historical surface-water quality for the Red River Valley, New Mexico, 1965 to 2001

Historical water-quality samples collected from the Red River over the past 35 years were compiled, reviewed for quality, and evaluated to determine influences on water quality over time. Hydrologic conditions in the Red River were found to have a major effect on water quality. The lowest sulfate concentrations were associated with the highest flow events, especially peak, rising limb, and falling limb conditions. The highest sulfate concentrations were associated with the early part of the rising limb of summer thunderstorm events and early snowmelt runoff, transient events that can be difficult to capture as part of planned sampling programs but were observed in some of the data. The first increase in flows in the spring, or during summer thunderstorm events, causes a flushing of sulfide oxidation products from scars and mine-disturbed areas to the Red River before being diluted by rising river waters. A trend of increasing sulfate concentrations and loads over long time periods also was noted at the Questa Ranger Station gage on the Red River, possibly related to mining activities, because the same trend is not apparent for concentrations upstream. This trend was only apparent when the dynamic events of snowmelt and summer rainstorms were eliminated and only low-flow concentrations were considered. An increase in sulfate concentrations and loads over time was not seen at locations upstream from the Molycorp, Inc., molybdenum mine and downstream from scar areas. Sulfate concentrations and loads and zinc concentrations downstream from the mine were uniformly higher, and alkalinity values were consistently lower, than those upstream from the mine, suggesting that additional sources of sulfate, zinc, and acidity enter the river in the vicinity of the mine. During storm events, alkalinity values decreased both upstream and downstream of the mine, indicating that natural sources, most likely scar areas, can cause short-term changes in the buffering capacity of the Red River. The major-element water chemistry of the Red River is controlled by dissolution of calcite and gypsum and the oxidation of pyrite, and the river is generally not well buffered with respect to pH. During higher-flow periods, Red River water was diluted by calcium-carbonate waters, most likely from unmineralized Red River tributaries and areas upstream from scars. The effect of pyrite oxidation on Red River water chemistry was more pronounced after the early 1980's. Elevated zinc concentrations were most apparent during summer thunderstorm and rising limb times, which also were associated with a decrease in alkalinity and an increase in sulfate concentrations and conductivity. The water-quality results demonstrate that it is critical to consider hydrologic conditions when interpreting water chemistry in naturally mineralized or mined drainages.

New Mexico↗
USGS1979

Preconstruction and postconstruction ground-water levels, Lock and Dam 2, Red River Valley, Louisiana

Proposed construction of a series of locks and dams in the Red River in Louisiana will cause a permanent increase in average river stage. The potentiometric surface of the shallow alluvial aquifer and the water table in the fine-grained material confining the aquifer will be affected. The purpose of this study using digital-modeling techniques, was to predict the average postconstruction potentiometric surface (steady state) and the water table (nonsteady state) so that potential effects of the water-level changes could be evaluated. Plans for lock and dam 2 at mile 87 (kilometer 140) above the mouth of the Red River call for a pool elevation of 58 feet (17.7 meters) and will cause an average increase in river stage of 12.5 feet (3.8 meters). As a result, ground-water levels will be raised 1 foot (0.3 meter) or more within 4 miles (6.4 kilometers) of the river and will be near land surface in low areas. The potentiometric surface may be as much as 1 to 2 feet (0.3 to 0.6 meter) above land surface south of Latanier along Chatlin Lake Canal and south of the Annandale area of Alexandria. The magnitude of ground-water-level fluctuations near the river will be reduced.

Louisiana↗
USGS1979

Preconstruction and postconstruction ground-water levels, Lock and Dam 3, Red River Valley, Louisiana

Proposed construction of a series of locks and dams in the Red River in Louisiana will cause a permanent increase in average river stage. The potentiometric surface of the shallow alluvial aquifer and the water table in the fine-grained material confining the aquifer will be affected. The purpose of this study, using digital-modeling techniques, was to predict the average postconstruction potentiometric surface (steady state) and the water table (nonsteady state) so that potential effects of the water-level changes could be evaluated. Plans for lock and dam 3 at realined mile 111 (kilometer 179) above the mouth of the Red River call for a pool elevation of 87 feet (27 meters) and will cause an average increase in river stage ranging from 21 to 3.5 feet (l.4 to 1.1 meters). As a result, ground-water levels will be raised to near land surface in low areas east of the river from the damsite to Aloha and in a 0.5-mile (0.8-kilometer) strip along the west side extending 9 miles (14 kilometers) above the dam. The potentiometric surface may be above land surface locally near the dam. The magnitude of ground-water-level fluctuations near the river will be reduced to less than half the preconstruction range.

Louisiana↗
USGS1979

Preconstruction and postconstruction ground-water levels, Lock and Dam 4, Red River Valley, Louisiana

Proposed construction of a series of locks and dams in the Red River in Louisiana will cause a permanent increase in average river stage. The potentiometric surface of the shallow alluvial aquifer and the water table in the fine-grained material confining the aquifer will be affected. The purpose of this study, using digital-modeling techniques, was to predict the average postconstruction potentiometric surface (steady state) and the water table (nonsteady state) so that potential effects of the water-level changes could be evaluated. Plans for lock and dam 4 at realined mile 154 (kilometer 250) above the mouth of the Red River call for a pool elevation of 115 feet (35 meters) and will cause an average increase in river stage ranging from 24 to 4.5 feet (7 to 1.4 meters). As a result, ground-water levels will be raised 1 foot (0.3 meter) or more between the Red River and Bayou Pierre from the dam to Coushatta , and below Campti, east of the river. The potentiometric surface may be at or near land surface in low areas between the Red River and Bayou Pierre, and above land surface locally upstream from the dam. The magnitude of ground-water-level fluctuations near the river will be reduced to less than half the present range.

Louisiana↗
USGS1979

Preconstruction and postconstruction ground-water levels, Lock and Dam 5 and 6, Red River Valley, Louisiana

Proposed construction of a series of locks and dams in the Red River in Louisiana will cause a permanent increase in average river stage. The potentiometric surface of the shallow alluvial aquifer and the water table in the fine-grained material confining the aquifer will be affected. The purpose of this study, using digital-modeling techniques, was to predict the average postconstruction potentiometric surface (steady state) and the water table (nonsteady state) so that potential effects of the water-level changes could be evaluated. Plans for lock and dam 5 at mile 243 (kilometer 390) above the mouth of the Red River call for a pool elevation of 145 feet (44 meters) and will cause an average increase in river stage of 23 feet (7.0 meters). As a result, ground-water levels in the pool area will be raised to near land surface in much of the area between the river and Bayou Pierre and as much as 2 miles (3.2 kilometers) east of the river from the dam upstream to realined mile 220 (kilometer 350). Areas of Barksdale Air Force Base where levels are now near land surface would be enlarged and extend downstream along Flat River to near Curtis. The potentiometric surface may be above land surface near Howard, Anderson Island, and Dixie Gardens. (Woodard-USGS)

Louisiana↗