Search USGS⌕ Search

Geology topics

Research about North Slope

Source-linked reports with geographic coverage including North Slope.

At least 19 recordsLinked to original sources
USGS2026

Permeability and compressibility of “seal” sediment overlying the B1 sand gas hydrate reservoir: Hydrate 02 Geo Data Well, Prudhoe Bay unit, Alaska North Slope

An important element in evaluating the viability of extracting methane from a gas hydrate-bearing reservoir is establishing the effectiveness of the overlying bounding sediment as a seal to prevent gas loss, to enable effective depressurization, and to prevent fluid from entering the reservoir during production. This laboratory study presents results for index properties (e.g., grain density, grain size, and liquid limit), compressibility and swelling indices, and permeability measurements on sediment overlying the gas hydrate-bearing reservoir that was the target of the recent JOGMEC-DOE-USGS collaborative gas hydrate production testing project on the Alaska North Slope (ANS). Sediment analyzed in this study was collected during pressure coring operations in the HYDRATE 02 Geo Data Well (GDW). The ∼6.1 m sediment interval recovered in Cores 13P and 14P (878.74–884.88 m measured depth, MD) exhibited heterogeneous sedimentologic characteristics at the centimeter scale, with sediments ranging from clay to thin silty-sand lithologies. Permeability measurements and index-property correlations indicate the interval’s overall in situ vertical permeability ranges from 0.2 to 3.6 microdarcy (μD). Results for compressibility ( C C = 0.255 ± 0.02) and swelling index ( C S = 0.04 ± 0.01) are consistent with estimates based on mineralogy and liquid limit correlations. Based on the measured compressibility, the ∼3 MPa increase in effective stress during the stable phase of depressurization-induced production is anticipated to have imposed 2.43 cm of compaction per meter in the reservoir overburden, reducing permeability by ∼36%. The overburden sediment’s low in situ permeability (3 to 4 orders of magnitude below permeabilities measured in the gas hydrate-bearing part of the B1 sand (unit B)) suggests the B1 sand′s overburden provides an effective seal. Such a seal promotes efficient production by limiting fluid flow into the reservoir during depressurization-induced gas hydrate dissociation.

Alaska↗
USGS2025

The effects of carnivory and herbivory on the energy balance of Arctic grizzly bears

Omnivores often face tradeoffs between selecting for spatially dispersed energy-dense vertebrate prey versus densely distributed herbivorous resources that have limited energetic value per unit intake. Arctic grizzly bears ( Ursus arctos ) are large omnivores within a resource-limited ecosystem that are known to exhibit smaller body masses and occur at lower densities than grizzly bears in other regions of North America. We evaluated the energy balance of Arctic grizzly bears during a portion of the fall hyperphagic period in two ecologically differing regions on Alaska’s northern Arctic coast by monitoring mass change, food intake, activity, and energy expenditure of 12 individuals over 17–22 days. Bears in coastal areas were more carnivorous than bears in the foothills that were predominantly herbivorous and frugivorous. Carnivory was associated with greater movement, body fat, and energy expenditure and two of four carnivorous bears lost mass. Overall, the mean body fat of the bears in this study was 34% lower than other grizzly bear populations in North America in the fall. Furthermore, the bears in this study exhibited relatively small changes in body mass (x̄ = 3%, range =−2 to 11%) that were 60% lower than other grizzly bear populations which typically gain substantial mass in the fall in preparation for denning. Our results, while representing a snapshot from a small number of bears during the fall hyperphagic period, are consistent with previous studies and indicate limited availability of energy-dense food resources during this time for grizzly bears in this region of the Arctic.

Alaska↗
USGS2024

Long-term distributed temperature sensing monitoring for near-wellbore gas migration and gas hydrate formation

Well integrity monitoring has always been a critical component of subsurface oil and gas operations. Distributed fiber-optic sensing is an emerging technology that shows great promise for monitoring processes, both in boreholes and in other settings. In this study, we present a case study of using distributed temperature sensing (DTS) technology to monitor a cemented and plugged well in the Alaska North Slope (ANS). The well was drilled as part of a long-term gas hydrate study, and the downhole DTS data were recorded over a period of approximately 2 years. By applying a temporal gradient and removing instrument instability noise, we reveal subtle (<0.001°C/h) thermal anomalies, which are characterized by brief warming periods followed by longer cooling periods at discrete depths along the borehole. The observed coherent events show an upward trajectory from deeper formations into the overlying permafrost interval, with the thermal anomalies concentrated in relatively coarse-grained sandstone layers. We also observe that the upward migration rate of the DTS anomalies varies with formation lithology and that there is a spatial and temporal correlation between the subsurface events and measured wellhead annular pressures. We interpret that the observed warming events represent the exothermic process of gas hydrate formation that is occurring in association with the upward migration of gas outside the well casing, and this interpretation is confirmed by numerical simulations. These observations demonstrate the ability of suitably processed DTS data to detect subtle processes and highlight the value of DTS technologies for wellbore integrity monitoring.

Alaska↗
USGS2024

Insights into glendonite formation from the upper Oligocene Sagavanirktok Formation, North Slope, Alaska

The type locality for the upper Oligocene Nuwok Member of the Sagavanirktok Formation (Carter Creek, North Slope, Alaska, USA) contains abundant occurrence of glendonite, a pseudomorph after the calcium carbonate mineral ikaite, which typically forms in the shallow subsurface of cold marine sediments. The region during the time of Nuwok Member deposition was located at a high latitude, similar to today, and the study site is characterized by sands and silty muds interpreted here to have been deposited in coastal and shelfal marine environments. Isotopic (Sr) and biostratigraphic (foraminifera) evidence presented here refine the depositional age of the outcrop to approximately 24 Ma. Glendonites occur in two basic forms: radial clusters, commonly centered around a single larger primary crystal ( approx. 10 cm; Type A) and larger single blades generally without accessory crystals (approx. 15–25 cm; Type B). Microscopic examination revealed a sequence of multiple types of replacive calcite that formed as a direct result of ikaite transformation: Type 1 rhombohedral crystals characterized by microporous and inclusion-rich cores and concentric zones, Type 2A, composed of clear calcite that overgrew and augmented Type 1 crystals, and inclusion-rich, microcrystalline Type 2B, which formed a matrix surrounding the rhombs and commonly dominates the outer rims of glendonite specimens. Type 3 calcite precipitated as fibrous, botryoidal epitaxial cement atop previous phases and is not ikaite-derived. These phases are distributed in similar ways in all examined specimens and are consistent with several previously described glendonite occurrences around the world, despite differing diagenetic and geologic histories. Stable isotope evidence (δ13C and δ18O) suggests sourcing of glendonite carbon from both organic and methanogenic sources. Glendonites of the Nuwok Member can therefore assist in the determination of a more comprehensive ikaite transformation model, improving our understanding of glendonite formation and the sedimentological and environmental context of their occurrence. Oligocene glendonites are uncommon globally; the well-preserved occurrence described here can allow future studies to better reconstruct Arctic environmental conditions and paleoclimates during this time.

Alaska↗
USGS2024

Characterization of the structural–stratigraphic and reservoir controls on the occurrence of gas hydrates in the Eileen Gas Hydrate Trend, Alaska North Slope

One of the most studied permafrost-associated gas hydrate accumulations in Arctic Alaska is the Eileen Gas Hydrate Trend. This study provides a detailed re-examination of the Eileen Gas Hydrate Trend with a focus on the gas hydrate accumulation in the western part of the Prudhoe Bay Unit. This integrated analysis of downhole well log data and published geophysical data has provided new insight on structural, stratigraphic, and reservoir controls on the occurrence of gas hydrates in the Eileen Gas Hydrate Trend. This study revealed the relatively complex nature of the gas hydrate occurrences in the Eileen Gas Hydrate Trend, with gas hydrates present in a series of coarsening upward, laterally pervasive, mostly fine-grained sand beds exhibiting high gas hydrate saturations. Most of the gas hydrate-bearing reservoirs in the Eileen Gas Hydrate Trend are laterally segmented into distinct northwest- to southeast-trending fault blocks, occur in a combination of structural–stratigraphic traps, and are only partially hydrate filled with distinct down-dip water contacts. These findings suggest that the traditional parts of a petroleum system (i.e., reservoir, gas source, gas migration, and geologic timing of the system formation) also control the occurrence of gas hydrates in the Eileen Gas Hydrate Trend.

Alaska↗
USGS2024

Assessing the utility of uncrewed aerial system photogrammetrically derived point clouds for land cover classification in the Alaska North Slope

Uncrewed aerial systems (UASs) have been used to collect “pseudo field plot” data in the form of large-scale stereo imagery to supplement and bolster direct field observations to monitor areas in Alaska. These data supplement field data that is difficult to collect in such a vast landscape with a relatively short field season. Dense photogrammetrically derived point clouds are created and are facilitated to extract land cover data using a support vector machine (SVM) classifier in this study. We test our approach using point clouds derived from 1-cm stereo imagery of plots in the Alaska North Slope region and compare the results to field observations. The results show that the overall accuracy of six land cover classes (bare soil, shrub, grass, forb/herb, rock, and litter) is 96.8% from classified patches. Shrub had the highest accuracy (>99%) and forb/herb achieved the lowest (<48%). This study reveals that the approach could be used as reference data to check field observations in remote areas.

Alaska↗
USGS2023

Unrecorded tundra fires of the Arctic Slope, Alaska USA

Few fires are known to have burned the tundra of the Arctic Slope north of the Brooks Range in Alaska, USA. A total of 90 fires between 1969 and 2022 are known. Because fire has been rare, old burns can be detected by the traces of thermokarst and distinct vegetation they leave in otherwise uniform tundra, which are visible in aerial photograph archives. Several prehistoric tundra burns have been found in this way. Detection of tundra fires in this sparsely populated and remote area has been historically inconsistent and opportunistic, relying on reports by aircraft pilots. Fire reports have been logged into an administrative database which, out of necessity, has been used to scientifically evaluate changes in the fire regime. To improve the consistency of the record, we completed a systematic search of Landsat Collection 2 for the Brooks Range Foothills ecoregion over the period 1972–2022. We found 57 unrecorded tundra burns, about 41% of the total, which now numbers 138. Only 15% and 33% of all fires appear in MODIS and VIIRS satellite-borne thermal anomaly products, respectively. The fire frequency in the first 37 years of the record is 0.89 y −1 for natural ignitions that spread ≥10 ha. Frequency in the last 13 years is 2.5 y −1 , indicating a nearly three-fold increase in fire frequency.

Alaska↗
USGS2022

Geological reservoir characterization of a gas hydrate prospect associated with the Hydrate-01 Stratigraphic Test Well, Alaska North Slope

Geological reservoir characterization is essential for accurate evaluation of gas production performance from gas hydrate reservoirs. Particularly, the understanding of reservoir architecture and heterogeneity is of great importance since these are considered as major controls on fluid hydrodynamic and thermodynamic conditions. This study deals with well log and three-dimensional (3-D) vertical seismic profile (VSP) data acquired from the Hydrate-01 Stratigraphic Test Well within the 7-11-12 prospect, Prudhoe Bay Unit, Alaska North Slope and reports on the results of geological/geophysical evaluation related to the geological structure and reservoir properties of the 7-11-12 prospect. The structural trends of the target reservoirs, based on well correlations, are mostly consistent with the predrill prediction using the surface seismic data, and infer the existence of subseismic faults cutting through the Hydrate-01 well. The 3-D VSP data confirm a down-to-the-east normal fault that offsets the reservoir units across the Hydrate-01 well, which is concordant with the well identification of the same fault, and indicate a northeast-dipping relay structure associated with the overstepping normal faults. The edge enhancement attribute associated with discontinuity generated from the 3-D VSP data shows small faults/fractures, possibly as part of a complex fault network within the imaged normal fault system. These results reveal that the 3-D VSP data provide detailed structural information that is not present from the surface seismic data. The Hydrate-01 well log data confirm the occurrence of gas hydrate at high saturation in the two targeted sand units (B1 and D1 sands), and the comparison to a nearby pre-existing well (7-11-12 well) shows the same general trend in gas hydrate saturation as a map of seismic impedance generated from surface seismic data. The well log data also suggest that the base of gas hydrate occurrence in the Hydrate-01 and 7-11-12 wells is almost aligned at the same depth in both of the targeted B1 and D1 sand reservoirs. Especially for the D1 sand in the Hydrate-01 well, the resistivity logs show a sharp transition from high gas hydrate saturation to fully water-saturated within the D1 sand, suggesting a common gas hydrate/water contact. The results of this study will be used to construct the geological models needed for reservoir simulation studies and they can provide important insights into the geological factors that control the occurrence of gas hydrate on the Alaska North Slope.

Alaska↗
USGS2022

Advanced distributed acoustic sensing vertical seismic profile imaging of an Alaska North Slope gas hydrate field

Gas hydrates are found in significant quantities on the North Slope of Alaska in subpermafrost sand units and intermixed in lower portions of permafrost within the hydrate stability window. While conventional surface seismic data and established imaging methods can indicate the presence of gas hydrate reservoirs, producing high-resolution images of (seismically) thin layers remains challenging due to the preferential attenuation of the higher-frequency data components. An alternative strategy is to use distributed acoustic sensing (DAS) involving cementing optical fibers into boreholes to measure seismic wavefield energy closer to the strata of interest using vertical seismic profiling (VSP). DAS VSP imaging takes advantage of the shorter travel paths and reduced attenuation to generate higher-resolution near-well images. We illustrate these benefits on a DAS VSP data set acquired at the Hydrate-01 stratigraphic test well located in the Prudhoe Bay Unit of Alaska where significant gas hydrate deposits have been detected in two subpermafrost sand layers that are intended for long-duration production testing. Our DAS data preprocessing workflow effectively isolates the upgoing compressional-wave (P-wave) reflections required for subsurface acoustic imaging. After applying three-dimensional (3-D) tomography to improve the quality of the 3-D migration velocity model, we use 3-D reverse-time migration (RTM) to develop high-quality images of the two target sands and minor near-well faulting. We validate our RTM images through highly accurate well-ties with previously acquired petrophysical log data. This study demonstrates that combining 3-D RTM imaging with DAS VSP data provides significant value to gas hydrate and similar projects, and it suggests that more advanced inversion approaches such as (elastic) least-squares RTM could recover higher-resolution and more quantitative estimates of subsurface reflectivity, which would be valuable for refining the understanding of gas hydrate systems.

Alaska↗
USGS2022

Gas hydrate saturation estimates, gas hydrate occurrence, and reservoir characteristics based on well log data from the hydrate-01 stratigraphic test well, Alaska North Slope

The Hydrate-01 Stratigraphic Test Well was drilled at the Kuparuk 7-11-12 site on the Alaska North Slope in December 2018. Sonic log data provide compressional (P) and shear (S) slowness from which we determine gas hydrate saturation ( S gh ) estimates using effective medium theory. The sonic S gh estimates compare favorably with S gh estimated from resistivity and nuclear magnetic resonance (NMR) logs, showing that gas hydrate occupies up to approximately 90% of the pore space in the target reservoir sands. The informally named B1 sand (2294 feet below mean sea level) shows lower V P / V S ratios than the D1 sand (2770 feet below mean sea level), with the lower part of the B1 sand showing lower V P / V S ratios than the upper part of the B1 sand. This corresponds to a stiffer, or more “cemented”, behavior for the lower B1 sand and less cemented behavior for the D1 sand. This trend could be due to differences in the reservoirs themselves or in the gas hydrate morphology or to both factors. We observe that the presence of gas hydrate in the upper B1 sand has greater impact on hydraulic permeability (measurements suggest a greater difference between intrinsic and effective permeability) than in the D1 sand, possibly related to gas hydrate morphology but more likely due simply to higher gas hydrate saturations in the upper B1 sand. Analyses of S gh relative to porosity, shale fraction, and intrinsic permeability show that reservoir quality (as represented by these three metrics) exerts control on gas hydrate saturation. Grain size and mineralogy data show somewhat smaller grains and better sorting in the D1 reservoir relative to the upper B1 reservoir and smaller grains and greater clay fraction in the lower B1 reservoir relative to the other two reservoir zones. Together, these data suggest that reservoir characteristics play a role in the observed V P / V S patterns, but gas hydrate morphology (possibly varying with saturation) must also be considered.

Alaska↗
USGS2021

Multiple physical properties of gas hydrate-bearing sediments recovered from Alaska North Slope 2018 Hydrate-01 Stratigraphic Test Well

Knowledge of the petrophysical and geomechanical properties of gas hydrate-bearing sediments is essential for predicting reservoir responses to gas production from gas hydrate reservoirs. In December 2018, Stratigraphic Test Well Hydrate-01 was drilled in the western part of the Prudhoe Bay Unit, Alaska North Slope, as part of the technical planning effort for a future long-term gas hydrate production test. Side-wall pressure coring was conducted to recover gas hydrate-bearing sediments from two reservoir sections named Unit B and Unit D. A total of 34 cores were successfully recovered during five runs of a wireline deployed pressure corer, and a total of 17 cores were preserved for advanced laboratory analysis. The samples were frozen inside the pressure core autoclave by liquid nitrogen while at high pressure before being removed and stored under liquid nitrogen at atmospheric pressure. High-resolution X-ray computed tomography showed the samples were high-quality, with undisturbed lithological layers. The Unit B and D sediments were categorized as sand or sandy silt with high hydrate saturation. Gas compositions suggest the hydrates formed with thermogenic and microbial mixed gases. Permeability tests and triaxial compression tests were conducted on the hydrate-bearing sediments. Low strengthening and high permeability at hydrate saturation S h > 80% were observed. There was a small permeability reduction during the triaxial compression tests owing to porosity loss with increasing effective stress in the highly permeable sandy sediment after hydrate dissociation. The apparent minimal changes in porosity and permeability during the tests were due to the low-clay content and low compressibility of the quartz sand grains in the recovered cores. X-ray powder diffraction and thermal conductivity analysis also suggested a high quartz content for the analyzed samples.

Alaska↗
USGS2021

Geochemical advances in Arctic Alaska oil typing - North Slope oil correlation and charge history

The Arctic Alaska petroleum province is geologically and geochemically complex. Mixed hydrocarbon charge from multiple source rocks and/or levels of thermal maturity is common within an individual oil pool. Biomarker and chemometric statistical analyses were used to correlate twenty-nine oils to five oil families derived from: (1) Triassic Shublik Formation (calcareous organofacies), (2) Triassic Shublik Formation (shaly organofacies), (3) Jurassic Kingak Shale, (4) Cretaceous shale (pebble shale unit and Hue Shale), and (5) Paleogene shale (Canning Formation). Age-diagnostic and source-related oil biomarker parameters establish clear genetic relationships between the normal oil-window components and their putative source designations. However, application of diamondoid analyses reveals mixed-oil accumulations with postmature charge contributions (diamondoid-rich and biomarker-poor) in many oils. Most sampled reservoirs contain a predominant charge derived from a single oil-window source plus a minor contribution from one or more higher maturity source(s). Variations in source organofacies also are recognized in the Shublik, Kingak, and Cretaceous oil families. In some cases, oils from multiple pools within a single field display relatively homogeneous geochemical profiles, suggesting a common source and migration pathway. For example, oil from the significant Pikka discovery is inferred to originate mainly from the calcareous Shublik Formation. In other cases, variability among oils from multiple pools within a single field (e.g., Milne Point, Colville River, and Northstar) likely indicates a more complex source, migration, and charge history. Results may be useful for anticipating the composition of oil charge in stratigraphic traps with low-permeability sandstone reservoirs, where oil gravity and other chemical parameters may influence economic viability.

Alaska↗
USGS2020

The influence of snow cover, air temperature, and groundwater flow on the active-layer thermal regime of Arctic hillslopes drained by water tracks

Permafrost in Arctic watersheds limits soil biological activity to a thin, seasonally thawed active layer that contributes water to streams. In many hillslopes, relatively wet drainage features called water tracks have distinct freeze-thaw patterns that affect groundwater flow and storage, and thus the export of heat and solutes to Arctic streams. This study uses groundwater flow and energy transport models to examine potential controls on the timing and duration of freeze–thaw conditions and the magnitude of temperature fluctuations within water tracks and their adjacent hillslopes. The simulated length of the active-layer thaw season varies by 1 month over the range of snow-cover and mean annual air-temperature scenarios simulated. The timing and duration of freezing is particularly sensitive to depth and duration of snow cover. Thus, the deeper snowpack covers that can accumulate in water tracks contribute to their more persistent thaw conditions and their ability to conduct groundwater downslope. A three-dimensional simulation shows that during the summer thaw season, the water track captures groundwater laterally from half way across the hillslope. The models presented here elucidate key mechanisms driving small-scale variation in the active-layer thermal regime of tundra hillslopes, which may be responsible for changes in drainage-network geometry and Arctic biogeochemical fluxes under a warming climate.

Alaska↗
USGS2020

Surface to subsurface correlation of the Middle-Upper Triassic Shublik Formation within a revised sequence stratigraphic framework

Recent work on cores and outcrops of the Middle-Upper Triassic Shublik Formation has facilitated surface to subsurface correlation of depositional sequences across the Alaska North Slope. Five transgressive-regressive depositional sequences have been defined within three large-scale stratigraphic units. Outcrop spectral gamma-ray (GR) profiles were used to correlate observed stacking patterns with nearby exploration wells, and GR logs from 161 exploration wells were used to correlate the three large-scale stratigraphic units across the North Slope and nearby offshore. Interpretations of depositional facies and sequence stratigraphy in cores from 26 wells were used to corroborate regional correlations. Isochore maps constructed for each of the three stratigraphic units illustrate the influence of accommodation on depositional patterns and suggest reactivation of several older tectonic elements during Shublik deposition. An isochore map of the richest, oil-prone interval of the Shublik Formation reveals a thick pod south of Harrison Bay, the eastern part of which lies beneath a recent giant Shublik-sourced oil discovery in the Cretaceous Nanushuk Formation. In addition, when integrated with thermal maturity, this isochore map may provide leads for areas that are optimal for unconventional resource exploration.

Alaska↗
USGS2020

Alaska North Slope 2018 Hydrate-01 Stratigraphic Test Well: Technical results

The Hydrate-01 Stratigraphic Test Well was drilled in December 2018 to confirm that a seismically-identified location within the western Prudhoe Bay Unit might be suitable for extended-duration scientific production testing. The well tested two primary targets: the deeper Unit B is highly favorable due to optimal reservoir temperature and minimal observed risk for direct communication with permeable, hydrate-free water-bearing zones. The shallower Unit D provides a secondary target and opportunity to assess additional scientific and operational issues.

Alaska↗
USGS2020

Gas hydrate saturation estimation from acoustic log data in the 2018 Alaska North Slope Hydrate-01 stratigraphic test well

Completed in December 2018, the Alaska North Slope Hydrate 01 stratigraphic test well provides a wealth of logging-while-drilling (LWD) data for strata to below the base of gas hydrate stability (BGHS). This well is intended to be the first of three wells drilled for a long-term gas hydrate production test to be conducted by the U.S. Department of Energy National Energy Technology Laboratory, the Japan Oil, Gas and Metals National Corporation, and the U.S. Geological Survey (USGS). The Hydrate 01 stratigraphic test well confirmed the presence of gas hydrate in two sand reservoirs within the hydrate stability zone, indicating the suitability of this location for a long-term gas hydrate production test. The USGS, using an effective-medium-theory rock-physics approach, has estimated gas hydrate saturations from compressional (P) and shear (S) wave log data acquired in the Hydrate 01 well. We assume that gas hydrate occurs as pore-filling load-bearing material (i.e., part of the grain matrix). For Unit D, approximately 500 feet above the BGHS, both P-wave and S-wave acoustic logs indicate high gas hydrate saturations with S-wave results slightly lower than those for P-waves. For Unit B, located just above the BGHS, we obtain high gas hydrate saturation estimates from both sonic logs. Our P-wave saturation estimates agree well with results from electrical-resistivity-based estimates, whereas estimates from nuclear magnetic resonance LWD data generally suggest 5 to 10 percent higher saturations; our S-wave results suggest lower saturations. These differences likely indicate complexities in the form of gas hydrate occurrence within the sediment pore space, potentially including differences between hydrate occurrence in Units B and D.

Alaska↗
USGS2020

EMD Gas Hydrates Committee annual report

Global research on the potential commercial viability of gas extraction from gas hydrates is continuing, predominantly in Asia and in the United States, where recent efforts have focused on the exploration and characterization of gas hydrate petroleum systems and conducting controlled production tests of gas hydrate deposits hosted in mostly sand-rich reservoir systems. In 2017, gas hydrate production testing was conducted in marine settings in the offshore of Japan and China. An additional test was conducted in the Shenhu region of the South China Sea in 2020 to further evaluate the effectiveness of various well completion technologies to produce gas from gas hydrates. Late in 2018, a research partnership led by the U.S. Department of Energy National Energy Technology Laboratory and the Japan Oil, Gas and Metals National Corporation established a new Alaska North Slope test site for an extended gas hydrate production pilot with the completion of a stratigraphic test well. With the successful completion of the Prudhoe Bay Unit Hydrate-01 stratigraphic test well, planning is now underway for drilling of three additional wells at the Alaska test site, which will include a geoscience data well and two production test wells. In 2019, the Government of India released the results of one of the most comprehensive gas hydrate scientific drilling investigations ever undertaken, the leadership of the Indian National Gas Hydrate Program Expedition 02 reported on the discovery of several significant gas hydrate accumulations that were considered suitable for future gas hydrate production testing. In September of 2019, the U.S. Geological Survey released a new assessment of the technically recoverable gas hydrate resources on the Alaska North Slope. In 2018, the University of Texas at Austin released a comprehensive report describing the operational and initial technical results of the UT-GOM2-1 Hydrate Pressure Coring Expedition, which drilled and partially cored two wells in Green Canyon Block 955 in the deepwater Gulf of Mexico. The results of these recently complete gas hydrate geologic and production studies have been further reviewed in this AAPG-EMD Gas Hydrate Committee report.

Alaska↗