Search USGS⌕ Search

Geology topics

Research about Los Angeles, California

Source-linked reports with geographic coverage including Los Angeles, California.

At least 55 records · Page 3Linked to original sources
USGS1998

First-generation site-response maps for the Los Angeles region based on earthquake ground motions

Ground-motion records from aftershocks of the 1994 Northridge earthquake and mainshock records from the 1971 San Fernando, 1987 Whittier Narrows, 1991 Sierra Madre, and 1994 Northridge earthquakes are used to estimate site response relative to a rock site for the urban Los Angeles area. Site response is estimated at 232 mainshock and 201 aftershock sites relative to a low-amplitude site in the Santa Monica Mountains. Average amplification values are calculated for the frequency bands: 1 to 3, 3 to 5, and 5 to 7 Hz. These bands are chosen based on limitations in aftershock recording equipment at lower frequencies and reduced significance to the building inventory at higher frequencies. Site amplification factors determined at the instrumented locations are grouped by the surficial geology and contoured to produce a continuous spatial estimation of amplification. The maps in this article represent the first attempt to produce estimates of site amplification based on observations of ground motion for such a large areal extent of the Los Angeles region. These maps are expected to evolve as more data become available and more analysis is done.

California↗
USGS1998

The San Gabriel Mountains bright reflective zone: Possible evidence of young mid-crustal thrust faulting in southern California

During the Los Angeles Region Seismic Experiment (LARSE), a reflection/refraction survey was conducted along a line extending northeastward from Seal Beach, California, to the Mojave Desert, crossing the Los Angeles basin and San Gabriel Mountains. Shots and receivers were spaced most densely through the San Gabriel Mountains for the purpose of obtaining a combined reflection and refraction image of the crust in that area. A stack of common-midpoint (CMP) data reveals a bright reflective zone, 1-s thick, that dominates the stack and extends throughout most of the mid-crust of the San Gabriel Mountains. The top of this zone ranges in depth from 6 s (∼18-km depth) in the southern San Gabriel Mountains to 7.5 s (∼23-km depth) in the northern San Gabriel Mountains. The zone bends downward beneath the surface traces of the San Gabriel and San Andreas faults. It is brightest between these two faults, where it is given the name San Gabriel Mountains ‘bright spot’ (SGMBS), and becomes more poorly defined south of the San Gabriel fault and north of the San Andreas fault. The polarity of the seismic signal at the top of this zone is clearly negative, and our analysis suggests it represents a negative velocity step. The magnitude of the velocity step is approximately 1.7 km/s. In at least one location, an event with positive polarity can be observed 0.2 s beneath the top of this zone, indicating a thickness of the order of 500 m for the low-velocity zone at this location. Several factors combine to make the preferred interpretation of this bright reflective zone a young fault zone, possibly a ‘master’ decollement. (1) It represents a significant velocity reduction. If the rocks in this zone contain fluids, such a reduction could be caused by a differential change in fluid pressure between the caprock and the rocks in the SGMBS; near-lithostatic fluid pressure is required in the SGMBS. Such differential changes are believed to occur in the neighborhood of active fault zones, where ‘fault-value’ action has been postulated. Less likely alternative explanations for this velocity reduction include the presence of magma and a change in composition to serpentinite or metagraywacke. (2) It occurs at or near the brittle-ductile transition, at least in the southern San Gabriel Mountains, a possible zone of concentrated shear. (3) A thin reflection rising from its top in the southern San Gabriel Mountains projects to the hypocenter of the 1987 M 5.9 Whittier Narrows earthquake, a blind thrust-fault earthquake with one focal plane subparallel to the reflection. Alternatively, one could argue that the bends or disruptions in the reflective zone seen at the San Gabriel and San Andreas faults are actually offsets and that the reflective zone is therefore an older feature, possibly an older fault zone.

California↗
USGS1998

A method for producing digital probabilistic seismic landslide hazard maps: An example from the Los Angeles, California, area

The 1994 Northridge, California, earthquake is the first earthquake for which we have all of the data sets needed to conduct a rigorous regional analysis of seismic slope instability. These data sets include (1) a comprehensive inventory of triggered landslides, (2) about 200 strong-motion records of the mainshock, (3) 1:24,000-scale geologic mapping of the region, (4) extensive data on engineering properties of geologic units, and (5) high-resolution digital elevation models of the topography. All of these data sets have been digitized and rasterized at 10-m grid spacing in the ARC/INFO GIS platform. Combining these data sets in a dynamic model based on Newmark's permanent-deformation (sliding-block) analysis yields estimates of coseismic landslide displacement in each grid cell from the Northridge earthquake. The modeled displacements are then compared with the digital inventory of landslides triggered by the Northridge earthquake to construct a probability curve relating predicted displacement to probability of failure. This probability function can be applied to predict and map the spatial variability in failure probability in any ground-shaking conditions of interest. We anticipate that this mapping procedure will be used to construct seismic landslide hazard maps that will assist in emergency preparedness planning and in making rational decisions regarding development and construction in areas susceptible to seismic slope failure.

California↗
USGS1997

Variability of site response in the Los Angeles urban area

This article addresses the variability of site response in the Los Angeles area and possible structural causes for the observations. Aftershock records from 231 sites in the San Fernando and Los Angeles basins and the surrounding mountains are used in this study. Spectral ratios, taken with respect to a low-amplitude reference site, are used to document the variation in site amplification in the frequency range 2 to 6 Hz, both spatially and with backazimuth to the source. At higher frequencies (6 to 10 Hz), spectral ratios are shown to have greater spatial variability. Interstation spectral ratios are used to measure the standard deviation among source as a function of station separation. An increase in the variation in ground motion is shown to take place at a station separation of 1 km. Relative site-response estimates between nearby stations are used to demonstrate that preferred directions of motion can exist even in areas with no surface topographic effects.

California↗
USGS1997

Determination of site amplification in the Los Angeles urban area from inversion of strong-motion records

The amplification of strong ground motion at sites in the greater Los Angeles, California, region is determined using the generalized-inverse method of Andrews (1986). Site-amplification estimates are determined at 281 strong-motion sites that provided horizontal-component accelerograms from the 1971 San Fernando, 1987 Whittier Narrows, 1991 Sierra Madre, or 1994 Northridge mainshocks. The estimates are determined relative to the spectral level recorded at a single reference site. In a second inversion, a source-site interaction term is added to Andrews's (1986) model to quantify the effect selected mainshock records have on site-amplification estimates. The source-site interaction term is applied to the San Fernando Valley sites' records of the Northridge earthquake and to three Los Angeles basin sites' records of the Whittier Narrows mainshock.

California↗
USGS1997

Estimating the diminution of shear-wave amplitude with distance: Application to the Los Angeles, California, urban area

The rate of decay with distance of shear-wave amplitude, computed from 20-sec S -wave spectra, is determined from TERRA scope records of small earthquakes in the greater Los Angeles area. Piecewise log-linear interpolation functions and traditional diminution functions are used to fit spectral decay to a maximum distance of 150 km. Simultaneously, isotropic source and receiver terms are determined. Separate branches of the spectral decay function are found for two categories of source depth: greater than 10 km and less than 10 km. In the hypocentral distance range of 20 to 150 km and in the frequency range of 0.5 to 8.0 Hz, an important result of the investigation is that the horizontal-component decay rate associated with deeper-crustal sources is generally greater than that associated with shallower sources and is greater than that which is estimated using more traditional models of spectral decay with distance. The same behavior generally holds for vertical-component spectra. The variation in apparent attenuation rate with source depth should affect seismic-hazard estimates associated with the rupture of blind thrust faults in the Los Angeles basin and vicinity. The results of the inversions suggest that interpolation function representations of spectral decay are sensitive to perturbations of S -wave amplitude due to crustal reflectors, such as post-critical S -wave arrivals from mid-crustal to deep-crustal velocity interfaces.

California↗
USGS1996

Site-response maps for the Los Angeles region based on earthquake ground motions

Ground-motion records from aftershocks of the 1994 Northridge earthquake and main-shock records from the 1971 San Fernando, 1987 Whittier Narrows, 1991 Sierra Madre, and 1994 Northridge earthquakes are used to estimate site response in the urban Los Angeles, California, area. Two frequency bands are considered, 0.5-1.5 Hz and 2.0-6.0 Hz. Instrument characteristics prevented going to lower frequencies, and frequencies above 6.0 Hz are less important to the building inventory. Site response determined at the instrumented locations is associated with the surficial geology and contoured to produce a continuous spatial estimation of site response. The maps in this report are preliminary and will evolve as more data become available and more analysis is done.

California↗
USGS1995

Earthquakes in the Los Angeles metropolitan region: A possible fractal distribution of rupture size

Although there is debate on the maximum size of earthquake that is possible on any of several known fault systems in the greater Los Angeles metropolitan region, it is reasonable to assume that the distribution of earthquakes will follow a fractal distribution of rupture areas. For this assumption and an overall slip-rate for the region of approximately 1 centimeter per year, roughly one magnitude 7.4 to 7.5 event is expected to occur every 245 to 325 years. A model in which the earthquake distribution is fractal predicts that, additionally, there should be approximately six events in the range of magnitude 6.6 in this same span of time, a higher rate than has occurred in the historic record.

California↗
USGS1995

Multichannel seismic-reflection profiling on the R/V Maurice Ewing during the Los Angeles Region Seismic Experiment (LARSE), California

This report describes the acquisition of deep-crustal multichannel seismic-reflection data in the Inner California Borderland aboard the R/V Maurice Ewing, conducted in October 1994 as part of the Los Angeles Regional Seismic Experiment (LARSE). LARSE is a cooperative study of the crustal structure of southern California involving earth scientists from the U.S. Geological Survey, Caltech, the University of Southern California, the University of California Los Angeles, and the Southern California Earthquake Center (SCEC). During LARSE, the R/V Ewing's 20- element air gun array, totaling 137.7 liters (8470 cu. in.), was used as the primary seismic source for wide-angle recording along three main onshore-offshore lines centered on the Los Angeles basin and the epicenters of the 1933 Long Beach and 1994 Northridge earthquakes. The LARSE onshore-offshore lines were each 200-250 km long, with the offshore portions being between 90 and 150 km long. The nearly 24,000 air gun signals generated by the Ewing were recorded by an array of 170 PASSCAL REFTEK recorders deployed at 2 km intervals along all three of the onshore lines and 9 ocean bottom seismometers (OBSs) deployed along two of the lines. Separate passes over the OBS-deployment lines were performed with a long air gun repetition rate (60 and 90 seconds) to minimize acoustic-wave interference from previous shots in the OBS data. The Ewing's 4.2-km, 160-channel, digital streamer was also used to record approximately 1250 km of 40-fold multichannel seismic-reflection data. To enhance the fold of the wide-angle data recorded onshore, mitigating against cultural and wind noise in the Los Angeles basin, the entire ship track was repeated at least once resulting in fewer than about 660 km of unique trackline coverage in the Inner Borderland. Portions of the seismic-reflection lines were repeated up to 6 times. A variety of other geophysical data were also continuously recorded, including 3.5 kHz bathymetry, multi-beam swath Hydrosweep bathymetry, magnetics, and gravity data. In this report, we describe the equipment and procedures used to acquire multichannel seismic-reflection and other geophysical data aboard the Ewing, provide a detailed cruise narrative, discuss the reduction of the data, and present near-trace constant offset seismic sections of the acquired profiles.

California↗
USGS1995

Earthquake damage in greater Los Angeles

Generalized regions of highest damage from three Los Angeles area earthquakes of the 20th century. The area of highest damage from the 1971 San Fernando earthquake, not shown, lay mostly within the area that experience high damage in 19947. The map illustrates that moderate magnitude earthquakes can produce series effects over large areas. The map is not intended to depict future damage patterns.

California↗
USGS1991

Seismic excitation by the space shuttle Columbia

Seismic stations in southern California recorded the atmospheric shock waves generated by the space shuttle Columbia on its return to the Edwards Air Force base on 13 August 1989 (Fig. 1). In addition to the shock wave, the broad-band IRIS–TERRAscope station at Pasadena recorded a distinct pulse with a period of ~2–3 seconds, which arrived 12.5 seconds before the shock wave (Fig. 2). This pulse was also recorded at the University of Southern California, near downtown Los Angeles, where it arrived 3 seconds after the shock wave. The origin of this pulse could not be readily identified. We show here that it was a seismic P wave excited by the motion of high-rise buildings in downtown Los Angeles, which were hit by the shock wave. The proximity of the natural period of the high-rise buildings to that of the Los Angeles basin enabled efficient energy transfer from shock wave to seismic wave.

California↗
USGS1991

Torsional response of unique building

Acceleration response records obtained during the October 1, 1987 Whittier‐Narrows earthquake ( M s = 5.6 ) "> ( M s = 5.6 ) from the 32‐story, vertically irregular 1100 Wilshire Finance Building, of which the cross section changes from a nominally rectangular shape to a triangular one, are analyzed. The building was instrumented with 21 channels of synchronized sensors, consisting of 12 uniaxial accelerometers deployed throughout the superstructure and connected to a central recording system and three triaxial strong‐motion accelerographs in the basement. At each of the four levels of the superstructure, three uniaxial accelerometers were deployed, two parallel and at a distance apart, and the third one orthogonal to the parallel pair. The records permit the identification of the predominantly coupled torsional‐translational response of the building and the associated frequency at approximately 0.7–0.8 Hz from the difference between accelerations recorded by the parallel pairs of accelerometers at different levels. This mode corresponds to the second torsional mode. A translational mode at 0.3 Hz is also identified from the records. The center of rigidity of any instrumented level is identified by minimizing the coherence between the relative accelerations and the translational acceleration. Employing system identification techniques provides the modal damping percentage for the second torsional mode as 6–7%.

California↗
USGS1989

Map showing late Quaternary faults and 1978-84 seismicity of the Los Angeles region, California

The Los Angeles region of California faces the greatest seismic risk of any part of the United States. The region is inhabited by more than 11 million people and is one of the Nation's key commercial and industrial centers. It lies astride a web of potentially active faults, including those segments of the San Andreas fault with the highest probability for generating a great earthquake during the next 30 years (Lindh, 1983; Sykes and Nishenko, 1984; Wesson and Wallace, 1985; U.S. Geological Survey, 1988). Moreover, many potentially active faults that can generate moderate-size, but damaging earthquakes lie within the metropolitan areas. Earthquakes along some of these faults—for example, a magnitude 6.5 event on the Newport-Inglewood zone—could produce losses exceeding those from a great earthquake on the more distant San Andreas fault (Evernden and Thomson, 1985). This map shows, at 1:250,000 scale, known or suspected late Quaternary faults of the Los Angeles region, the ages of their most recent surface movements, and the associated earthquake activity for a recent 7-year period (1978 through 1984). The geologic and seismologic character of these faults and their potential for generating damaging earthquakes recently were evaluated by Ziony and Yerkes (1985). The map is intended primarily to inform scientists, engineers, and planners of the distribution of those faults that may have a potential for generating damaging earthquakes and (or) displacements of the Earth's surface. The map data also should contribute to further investigations of the seismotectonic setting of the Los Angeles region. The mapped area extends from lat 33°15' N. to 34°45' N. and from long 116°45' W. to 120°00' W. This region encompasses parts of the Transverse Ranges (including the Santa Ynez, Santa Susana, Santa Monica, San Gabriel, and San Bernardino Mountains), the Los Angeles basin, part of the Mojave Desert, and segments of the Peninsular Ranges (including the Puente Hills, Santa Ana Mountains, and the northern San Jacinto Mountains). Offshore, it includes the eastern Santa Barbara Channel, several of the Channel Islands, the Santa Monica and San Pedro basins, Santa Catalina Island, and part of the Gulf of Santa Catalina. In addition to the Los Angeles metropolitan area, the cities of Santa Barbara, Ventura, Riverside, and San Bernardino are within the map area.

California↗
USGS1988

The 1987 Whittier Narrows earthquake in the Los Angeles metropolitan area, California

The Whittier Narrows earthquake sequence (local magnitude, M L = 5.9), which caused over 358-million dollars damage, indicates that assessments of earthquake hazards in the Los Angeles metropolitan area may be underestimated. The sequence ruptured a previously unidentified thrust fault that may be part of a large system of thrust faults that extends across the entire east-west length of the northern margin of the Los Angeles basin. Peak horizontal accelerations from the main shock, which were measured at ground level and in structures, were as high as 0.6 g (where g is the acceleration of gravity at sea level) within 50 kilometers of the epicenter. The distribution of the modified Mercalli intensity VII reflects a broad north-south elongated zone of damage that is approximately centered on the main shock epicenter.

California↗
USGS1985

Evaluating earthquake hazards in the Los Angeles region— An earth-science perspective

Potentially destructive earthquakes are inevitable in the Los Angeles region of California, but hazards prediction can provide a basis for reducing damage and loss. This volume identifies the principal geologically controlled earthquake hazards of the region (surface faulting, strong shaking, ground failure, and tsunamis), summarizes methods for characterizing their extent and severity, and suggests opportunities for their reduction. Two systems of active faults generate earthquakes in the Los Angeles region: northwest-trending, chiefly horizontal-slip faults, such as the San Andreas, and west-trending, chiefly vertical-slip faults, such as those of the Transverse Ranges. Faults in these two systems have produced more than 40 damaging earthquakes since 1800. Ninety-five faults have slipped in late Quaternary time (approximately the past 750,000 yr) and are judged capable of generating future moderate to large earthquakes and displacing the ground surface. Average rates of late Quaternary slip or separation along these faults provide an index of their relative activity. The San Andreas and San Jacinto faults have slip rates measured in tens of millimeters per year, but most other faults have rates of about 1 mm/yr or less. Intermediate rates of as much as 6 mm/yr characterize a belt of Transverse Ranges faults that extends from near Santa Barbara to near San Bernardino. The dimensions of late Quaternary faults provide a basis for estimating the maximum sizes of likely future earthquakes in the Los Angeles region: moment magnitude .(M) 8 for the San Andreas, M 7 for the other northwest-trending elements of that fault system, and M 7.5 for the Transverse Ranges faults. Geologic and seismologic evidence along these faults, however, suggests that, for planning and designing noncritical facilities, appropriate sizes would be M 8 for the San Andreas, M 7 for the San Jacinto, M 6.5 for other northwest-trending faults, and M 6.5 to 7 for the Transverse Ranges faults. The geologic and seismologic record indicates that parts of the San Andreas and San Jacinto faults have generated major earthquakes having recurrence intervals of several tens to a few hundred years. In contrast, the geologic evidence at points along other active faults suggests recurrence intervals measured in many hundreds to several thousands of years. The distribution and character of late Quaternary surface faulting permit estimation of the likely location, style, and amount of future surface displacements. An extensive body of geologic and geotechnical information is used to evaluate areal differences in future levels of shaking. Bedrock and alluvial deposits are differentiated according to the physical properties that control shaking response; maps of these properties are prepared by analyzing existing geologic and soils maps, the geomorphology of surficial units, and. geotechnical data obtained from boreholes. The shear-wave velocities of near-surface geologic units must be estimated for some methods of evaluating shaking potential. Regional-scale maps of highly generalized shearwave velocity groups, based on the age and texture of exposed geologic units and on a simple two-dimensional model of Quaternary sediment distribution, provide a first approximation of the areal variability in shaking response. More accurate depictions of near-surface shear-wave velocity useful for predicting ground-motion parameters take into account the thickness of the Quaternary deposits, vertical variations in sediment .type, and the correlation of shear-wave velocity with standard penetration resistance of different sediments. A map of the upper Santa Ana River basin showing shear-wave velocities to depths equal to one-quarter wavelength of a 1-s shear wave demonstrates the three-dimensional mapping procedure. Four methods for predicting the distribution and strength of shaking from future earthquakes are presented. These techniques use different measures of strong-motion

California↗
USGS1984

A comparative ground response study near Los Angeles using recordings of Nevada nuclear tests and the 1971 San Fernando earthquake

A comparative ground response study at sites in the Los Angeles region is based on the extensive strong-motion data set recorded in the 1971 San Fernando earthquake and 159 three-component recordings of distant nuclear tests in Nevada. Amplitude spectral ratios computed for the nuclear test data over those frequency bands for which there is an adequate signal-to-noise ratio provide statistically stable estimates of the local ground response related to the type of local geologic conditions. Comparison of the strong-motion data recorded from the 1971 San Fernando earthquake with that recorded at 28 of the same sites for the nuclear tests show that the corresponding amplitude spectral ratios are statistically equivalent for most sites, provided reference stations are chosen to minimize effects on the earthquake data of azimuthal source variations and crustal propagation path. Statistical equivalence of the spectral ratios for the two types of data sources suggests that amplitude spectral ratios computed with respect to the appropriate reference station provide a first-order estimate of local ground response.

California↗