Search USGS⌕ Search

Geology topics

Research about Appalachian Basin

Source-linked reports with geographic coverage including Appalachian Basin.

At least 19 recordsLinked to original sources
USGS2024

Utica/Point Pleasant brine isotopic compositions (δ7Li, δ11B, δ138Ba) elucidate mechanisms of lithium enrichment in the Appalachian Basin

Global Li production will require a ~500 % increase to meet 2050 projected energy storage demands. One potential source is oil and gas wastewater (i.e., produced water or brine), which naturally has high total dissolved solids (TDS) concentrations, that can also be enriched in Li (>100 mg/L). Understanding the sources and mechanisms responsible for high naturally-occurring Li concentrations can aid in efficient targeting of these brines. The isotopic composition (δ 7 Li, δ 11 B, δ 138 Ba) of produced water and core samples from the Utica Shale and Point Pleasant Formation (UPP) in the Appalachian Basin, USA indicates that depth-dependent thermal maturity and water-rock interaction, including diagenetic clay mineral transformations, likely control Li concentrations. A survey of Li content in produced waters throughout the USA indicates that Appalachian Basin brines from the Marcellus Shale to the UPP have the potential for economic resource recovery.

Maryland, Ohio, Pennsylvania, West Virginia↗
USGS2019

Accuracy of methods for reporting inorganic element concentrations and radioactivity in oil and gas wastewaters from the Appalachian Basin, U.S. based on an inter-laboratory comparison.

Accurate and precise analyses of oil and gas (O&G) wastewaters and solids ( e.g. , sediments and sludge) are important for the regulatory monitoring of O&G development and tracing potential O&G contamination in the environment. In this study, 15 laboratories participated in an inter-laboratory comparison on the chemical characterization of three O&G wastewaters from the Appalachian Basin and four solids impacted by O&G development, with the goal of evaluating the quality of data and the accuracy of measurements for various analytes of concern. Using a variety of different methods, analytes in the wastewaters with high concentrations ( i.e. , >5 mg L −1 ) were easily detectable with relatively high accuracy, often within ±10% of the most probable value (MPV). In contrast, often less than 7 of the 15 labs were able to report detectable trace metal(loid) concentrations ( i.e. , Cr, Ni, Cu, Zn, As, and Pb) with accuracies of approximately ±40%. Despite most labs using inductively coupled plasma mass spectrometry (ICP-MS) with low instrument detection capabilities for trace metal analyses, large dilution factors during sample preparation and low trace metal concentrations in the wastewaters limited the number of quantifiable determinations and likely influenced analytical accuracy. In contrast, all the labs measuring Ra in the wastewaters were able to report detectable concentrations using a variety of methods including gamma spectroscopy and wet chemical approaches following Environmental Protection Agency (EPA) standard methods. However, the reported radium activities were often greater than ±30% different to the MPV possibly due to calibration inconsistencies among labs, radon leakage, or failing to correct for self-attenuation. Reported radium activities in solid materials had less variability (±20% from MPV) but accuracy could likely be improved by using certified radium standards and accounting for self-attenuation that results from matrix interferences or a density difference between the calibration standard and the unknown sample. This inter-laboratory comparison illustrates that numerous methods can be used to measure major cation, minor cation, and anion concentrations in O&G wastewaters with relatively high accuracy while trace metal(loid) and radioactivity analyses in liquids may often be over ±20% different from the MPV.

Appalachian Basin↗
USGS2019

Trade-offs relating to grassland and forest mine reclamation approaches in the central Appalachian region and its implications for the songbird community

Surface mining in the Appalachian region, USA, converts large areas of mature forest to early-successional habitat. This shift in landscape structure has the potential to reduce habitat availability and suitability for forest-dwelling songbirds by reducing and fragmenting mature forest, but also to increase habitat availability for grassland and shrubland-associated songbirds. We examined the influence of mountaintop mining/valley fill (MTMVF) reclamation habitats (grassland, shrubland, and remnant forest) on songbird community composition and abundance at three former MTMVF mines in southwestern West Virginia, relative to intact forest. We quantified the songbird community in 1999 and 2000 using point counts arranged throughout the mine complexes to assess landscape composition of the songbird community. Community analysis showed songbirds had strong associations with their respective guild based on species’ habitat preferences. Although remnant and intact forest treatments had similar species compositions, the forest interior guild had greater richness in intact than remnant forest. Total species richness was greatest in the reclaimed shrubland treatment. Focal species analysis followed similar trends as community assessments, as species’ abundances within treatment types were strongly associated with species’ habitat preferences. Our study indicates reclamation habitat decisions (i.e. grasslands versus forests) can have large effects on avian community composition. Determining appropriate mine restoration actions depends on the suite of species desired for long-term occupancy and their conservation priority.

Appalachian Basin↗
USGS2015

Geochemical and mineralogical sampling of the Devonian shales in the Broadtop synclinorium, Appalachian basin, in Virginia, West Virginia, Maryland, and Pennsylvania

Reconnaissance field mapping and outcrop sampling for geochemical and mineralogical analyses indicate that the Middle Devonian Marcellus Shale in the Broadtop synclinorium and nearby areas from southeastern West Virginia to south-central Pennsylvania has an organic content sufficiently high and a thermal maturity sufficiently moderate to be considered for a shale gas play. The organic matter-rich Marcellus Shale is present throughout most of the synclinorium, being absent only where it has been eroded from the crest of anticlines. Geochemical analyses of outcrop and well drill-cuttings samples indicate that variable levels of hydrocarbons have been generated and expelled from the kerogen originally in place in the mudstone. The mineralogical characteristics of the Marcellus Shale samples from the study area are conducive to a continuous resource play, but the Middle Devonian strata are folded, faulted, and moderately to heavily sheared in the Broadtop synclinorium. The presence of conventional anticlinal gas fields in the study area that are productive from the underlying Lower Devonian Oriskany Sandstone suggests that an unconventional (or continuous) shale gas system may be in place within the Marcellus Shale in the study area. Results of this study indicate that the Marcellus Shale in the Broadtop synclinorium generally is similar in organic geochemical nature throughout its extent, and based on the sample analyses, there are no clearly identifiable high potential areas (or “sweet spots”) in the study area. This report contains analyses of 132 outcrop and well drill-cuttings samples.

Maryland, Pennsylvania, Virginia, West Virginia↗
USGS2014

Executive summary

Fossil fuels from the Appalachian basin region have been major contributors to the Nation’s energy needs over much of the last three centuries. Early records indicate that Appalachian coal was first mined in the middle 1700s (Virginia and Pennsylvania) and was used sparingly to fuel colonial settlements and, later, a fledgling industrial-based economy along the eastern seaboard of the United States (de Witt and Milici, 1989). In 2011, central Appalachian basin coal production accounted for approximately 77 percent of all U.S. metallurgical (or coking) coal and 29 percent of total U.S. production (U.S. Energy Information Administration, 2013). Following initial discoveries and commercial use in western New York (1821) and Ohio and West Virginia (mid-1830s), the Appalachian petroleum (oil and gas) industry began in earnest in 1859 with the discovery of oil at the Drake well in northwestern Pennsylvania. Between 1860 and 1989, the Appalachian basin produced more than 2.5 billion barrels of oil (BBO) and more than 30 trillion cubic feet of gas (TCFG) from more than 500,000 wells (de Witt and Milici, 1989). Although both oil and gas continue to be produced in the Appalachian basin, most new wells in the region are drilled in shale reservoirs to produce natural gas. Appalachian coal and petroleum resources are still available in sufficient quantities to contribute significantly to the Nation’s energy needs. For example, the U.S. Energy Information Administration (2010) estimated that there are 6,484 million short tons of recoverable coal reserves in the Appalachian basin. Similarly, about 14.7 billion barrels of oil equivalent (BBOE) (1.2 BBO+81 TCFG [or 13.5 BBOE]) of recoverable Appalachian basin oil and gas remain available of an estimated ultimate endowment of approximately 25.5 billion BBOE (cumulative production + reserves + estimated recoverable undiscovered resources) (this volume, chap. C.1). U.S. Geological Survey (USGS) Professional Paper 1708 is a modern, indepth collection of reports, cross sections, and maps that describe the geology of the Appalachian basin and its fossil fuel resources. Several of the chapters have been published in outside journals or as other USGS publications. Although this volume is not a comprehensive regional treatment of all notable geologic and fossil fuel localities in the Appalachian basin, the selected study areas and topics presented in the chapters cover large segments of the basin and a wide range of stratigraphic intervals. As the title implies, this volume addresses topics that refer to the locations of coal and petroleum accumulations, the stratigraphic and structural framework, and the geochemical characteristics of the coal beds and petroleum in the basin, as well as the results and documentation of recent USGS assessments of coal, oil, and gas resources in the basin. Many of the maps and accompanying data supporting the reports in this volume are available as downloadable geographic information system (GIS) data files (such as selected coal beds, selected oil and gas fields, locations of oil and gas wells, coal production, coal chemistry, total petroleum system (TPS) boundaries, and bedrock geology). Log ASCII Standard (LAS) files for geophysical (gamma ray) wireline well logs also are included. This publication supplements and updates older USGS regional studies of Appalachian basin coal and petroleum resources such as those by Arndt and others (1968) and the numerous contributors to USGS Miscellaneous Map Series I−917 (for example, Harris and others, 1978), respectively. USGS Professional Paper 1708 is intended primarily for geoscientists in academia, industry, and government who are interested in Appalachian basin geology and its coal and petroleum resources. Other users, however, may find the wide variety of topics, papers, and digital images of value for landuse and policy planning issues. Among the anticipated benefits of the report are improvements in (1) resource assessment estimates and methodology, (2) exploration strategies, (3) basin models, and (4) energy use policies.

Appalachian Basin↗
USGS2013

Thermal maturity of northern Appalachian Basin Devonian shales: Insights from sterane and terpane biomarkers

To better estimate thermal maturity of Devonian shales in the northern Appalachian Basin, eleven samples of Marcellus and Huron Shale were characterized via multiple analytical techniques. Vitrinite reflectance, Rock–Eval pyrolysis, gas chromatography (GC) of whole rock extracts, and GC–mass spectrometry (GCMS) of extract saturate fractions were evaluated on three transects that lie across previously documented regional thermal maturity isolines. Results from vitrinite reflectance suggest that most samples are immature with respect to hydrocarbon generation. However, bulk geochemical data and sterane and terpane biomarker ratios from GCMS suggest that almost all samples are in the oil window. This observation is consistent with the presence of thermogenic gas in the study area and higher vitrinite reflectance values recorded from overlying Pennsylvanian coals. These results suggest that vitrinite reflectance is a poor predictor of thermal maturity in early mature areas of Devonian shale, perhaps because reported measurements often include determinations of solid bitumen reflectance. Vitrinite reflectance interpretations in areas of early mature Devonian shale should be supplanted by evaluation of thermal maturity information from biomarker ratios and bulk geochemical data.

Maryland, New York, Ohio, Pennsylvania, West Virgi↗
USGS2013

Water resources and shale gas/oil production in the Appalachian Basin: critical issues and evolving developments

Unconventional natural gas and oil resources in the United States are important components of a national energy program. While the Nation seeks greater energy independence and greener sources of energy, Federal agencies with environmental responsibilities, state and local regulators and water-resource agencies, and citizens throughout areas of unconventional shale gas development have concerns about the environmental effects of high volume hydraulic fracturing (HVHF), including those in the Appalachian Basin in the northeastern United States (fig. 1). Environmental concerns posing critical challenges include the availability and use of surface water and groundwater for hydraulic fracturing; the migration of stray gas and potential effects on overlying aquifers; the potential for flowback, formation fluids, and other wastes to contaminate surface water and groundwater; and the effects from drill pads, roads, and pipeline infrastructure on land disturbance in small watersheds and headwater streams (U.S. Government Printing Office, 2012). Federal, state, regional and local agencies, along with the gas industry, are striving to use the best science and technology to develop these unconventional resources in an environmentally safe manner. Some of these concerns were addressed in U.S. Geological Survey (USGS) Fact Sheet 2009–3032 (Soeder and Kappel, 2009) about potential critical effects on water resources associated with the development of gas extraction from the Marcellus Shale of the Hamilton Group (Ver Straeten and others, 1994). Since that time, (1) the extraction process has evolved, (2) environmental awareness related to high-volume hydraulic fracturing process has increased, (3) state regulations concerning gas well drilling have been modified, and (4) the practices used by industry to obtain, transport, recover, treat, recycle, and ultimately dispose of the spent fluids and solid waste materials have evolved. This report updates and expands on Fact Sheet 2009–3032 and presents new information regarding selected aspects of unconventional shale gas development in the Appalachian Basin (primarily Virginia, West Virginia, Maryland, Pennsylvania, Ohio, and New York). This document was prepared by the USGS, in cooperation with the U.S. Department of Energy, and reviews the evolving technical advances and scientific studies made in the Appalachian Basin between 2009 and the present (2013), addressing past and current issues for oil and gas development in the region.

Maryl;New York;Ohio;Pennsylvania;Virginia;West Vir↗
USGS2012

Distribution of arsenic, selenium, and other trace elements in high pyrite Appalachian coals: evidence for multiple episodes of pyrite formation

Pennsylvanian coals in the Appalachian Basin host pyrite that is locally enriched in potentially toxic trace elements such as As, Se, Hg, Pb, and Ni. A comparison of pyrite-rich coals from northwestern Alabama, eastern Kentucky, and West Virginia reveals differences in concentrations and mode of occurrence of trace elements in pyrite. Pyrite occurs as framboids, dendrites, or in massive crystalline form in cell lumens or crosscutting veins. Metal concentrations in pyrite vary over all scales, from microscopic to mine to regional, because trace elements are inhomogeneously distributed in the different morphological forms of pyrite, and in the multiple generations of sulfide mineral precipitates. Early diagenetic framboidal pyrite is usually depleted in As, Se, and Hg, and enriched in Pb and Ni, compared to other pyrite forms. In dendritic pyrite, maps of As distribution show a chemical gradient from As-rich centers to As-poor distal branches, whereas Se concentrations are highest at the distal edges of the branches. Massive crystalline pyrite that fills veins is composed of several generations of sulfide minerals. Pyrite in late-stage veins commonly exhibits As-rich growth zones, indicating a probable epigenetic hydrothermal origin. Selenium is concentrated at the distal edges of veins. A positive correlation of As and Se in pyrite veins from Kentucky coals, and of As and Hg in pyrite-filled veins from Alabama coals, suggests coprecipitation of these elements from the same fluid. In the Kentucky coal samples (n = 18), As and Se contents in pyrite-filled veins average 4200 ppm and 200 ppm, respectively. In Alabama coal samples, As in pyrite-filled veins averages 2700 ppm (n = 34), whereas As in pyrite-filled cellular structures averages 6470 ppm (n = 35). In these same Alabama samples, Se averages 80 ppm in pyrite-filled veins, but was below the detection limit in cell structures. In samples of West Virginia massive pyrite, As averages 1700 ppm, and Se averages 270 ppm (n = 24). The highest concentration of Hg (≤ 102 ppm) is in Alabama pyrite veins. Improved detailed descriptions of sulfide morphology, sulfide mineral paragenesis, and trace-element concentration and distribution allow more informed predictions of: (1) the relative rate of release of trace elements during weathering of pyrite in coals, and (2) the relative effectiveness of various coal-cleaning procedures of removing pyrite. For example, trace element-rich pyrite has been shown to be more soluble than stoichiometric pyrite, and fragile fine-grained pyrite forms such as dendrites and framboids are more susceptible to dissolution and disaggregation but less amenable to removal during coal cleaning.

Alabama;Kentucky;West Virginia↗
USGS2012

Determining the source and genetic fingerprint of natural gases using noble gas geochemistry: a northern Appalachian Basin case study

Silurian and Devonian natural gas reservoirs present within New York state represent an example of unconventional gas accumulations within the northern Appalachian Basin. These unconventional energy resources, previously thought to be noneconomically viable, have come into play following advances in drilling (i.e., horizontal drilling) and extraction (i.e., hydraulic fracturing) capabilities. Therefore, efforts to understand these and other domestic and global natural gas reserves have recently increased. The suspicion of fugitive mass migration issues within current Appalachian production fields has catalyzed the need to develop a greater understanding of the genetic grouping (source) and migrational history of natural gases in this area. We introduce new noble gas data in the context of published hydrocarbon carbon (C 1 ,C 2+ ) ( 13 C) data to explore the genesis of thermogenic gases in the Appalachian Basin. This study includes natural gases from two distinct genetic groups: group 1, Upper Devonian (Marcellus shale and Canadaway Group) gases generated in situ, characterized by early mature ( 13 C[ C1 C2 ][ 13 C 1 13 C 2 ]: –9 ), isotopically light methane, with low ( 4 He) (average, 1 10 3 cc/cc) elevated 4 He/ 40 Ar and 21 Ne / 40 Ar (where the asterisk denotes excess radiogenic or nucleogenic production beyond the atmospheric ratio), and a variable, atmospherically (air-saturated–water) derived noble gas component; and group 2, a migratory natural gas that emanated from Lower Ordovician source rocks (i.e., most likely, Middle Ordovician Trenton or Black River group) that is currently hosted primarily in Lower Silurian sands (i.e., Medina or Clinton group) characterized by isotopically heavy, mature methane ( 13 C [C1 – C2] [ 13 C 1 13 C 2 ]: 3 ), with high ( 4 He) (average, 1.85 10 3 cc/cc) 4 He/ 40 Ar and 21 Ne / 40 Ar near crustal production levels and elevated crustal noble gas content (enriched 4 He, 21 Ne , 40 Ar ). Because the release of each crustal noble gas (i.e., He, Ne, Ar) from mineral grains in the shale matrix is regulated by temperature, natural gases obtain and retain a record of the thermal conditions of the source rock. Therefore, noble gases constitute a valuable technique for distinguishing the genetic source and post-genetic processes of natural gases.

New York↗
USGS2012

Assessment of undiscovered oil and gas resources of the Ordovician Utica Shale of the Appalachian Basin Province, 2012

The U.S. Geological Survey assessed unconventional oil and gas resources of the Upper Ordovician Utica Shale and adjacent units in the Appalachian Basin Province. The assessment covers parts of Maryland, New York, Ohio, Pennsylvania, Virginia, and West Virginia. The geologic concept is that black shale of the Utica Shale and adjacent units generated hydrocarbons from Type II organic material in areas that are thermally mature for oil and gas. The source rocks generated petroleum that migrated into adjacent units, but also retained significant hydrocarbons within the matrix and adsorbed to organic matter of the shale. These are potentially technically recoverable resources that can be exploited by using horizontal drilling combined with hydraulic fracturing techniques.

Maryl;New York;Ohio;Pennsylvania;Virginia;West Vir↗
USGS2012

Thermal maturity map of Devonian shale in the Illinois, Michigan, and Appalachian basins of North America

Much of the oil and gas in the Illinois, Michigan, and Appalachian basins of eastern North America is thought to be derived from Devonian shale that is within these basins (for example, Milici and others, 2003; Swezey, 2002, 2008, 2009; Swezey and others, 2005, 2007). As the Devonian strata were buried by younger sediments, the Devonian shale was subjected to great temperature and pressure, and in some areas the shale crossed a thermal maturity threshold and began to generate oil. With increasing burial (increasing temperature and pressure), some of this oil-generating shale crossed another thermal maturity threshold and began to generate natural gas. Knowledge of the thermal maturity of the Devonian shale is therefore useful for predicting the occurrence and the spatial distribution of oil and gas within these three basins. This publication presents a thermal maturity map of Devonian shale in the Illinois, Michigan, and Appalachian basins. The map shows outlines of the three basins (dashed black lines) and an outline of Devonian shale (solid black lines). The basin outlines are compiled from Thomas and others (1989) and Swezey (2008, 2009). The outline of Devonian shale is a compilation from Freeman (1978), Thomas and others (1989), de Witt and others (1993), Dart (1995), Nicholson and others (2004), Dicken and others (2005a,b), and Stoeser and others (2005).

Alabama;Illinois;Indiana;Kentucky;Maryl;Michigan;M↗
USGS2011

Radium content of oil- and gas-field produced waters in the northern Appalachian Basin (USA): Summary and discussion of data

Radium activity data for waters co-produced with oil and gas in New York and Pennsylvania have been compiled from publicly available sources and are presented together with new data for six wells, including one time series. When available, total dissolved solids (TDS), and gross alpha and gross beta particle activities also were compiled. Data from the 1990s and earlier are from sandstone and limestone oil/gas reservoirs of Cambrian-Mississippian age; however, the recent data are almost exclusively from the Middle Devonian Marcellus Shale. The Marcellus Shale represents a vast resource of natural gas the size and significance of which have only recently been recognized. Exploitation of the Marcellus involves hydraulic fracturing of the shale to release tightly held gas. Analyses of the water produced with the gas commonly show elevated levels of salinity and radium. Similarities and differences in radium data from reservoirs of different ages and lithologies are discussed. The range of radium activities for samples from the Marcellus Shale (less than detection to 18,000 picocuries per liter (pCi/L)) overlaps the range for non-Marcellus reservoirs (less than detection to 6,700 pCi/L), and the median values are 2,460 pCi/L and 734 pCi/L, respectively. A positive correlation between the logs of TDS and radium activity can be demonstrated for the entire dataset, and controlling for this TDS dependence, Marcellus shale produced water samples contain statistically more radium than non-Marcellus samples. The radium isotopic ratio, Ra-228/Ra-226, in samples from the Marcellus Shale is generally less than 0.3, distinctly lower than the median values from other reservoirs. This ratio may serve as an indicator of the provenance or reservoir source of radium in samples of uncertain origin.

Pennsylvania;New York↗
USGS2010

New York-Alabama lineament: A buried right-slip fault bordering the Appalachians and mid-continent North America

The New York-Alabama (NY-AL) lineament , recognized in 1978, is a magnetic anomaly that delineates a fundamental though historically enigmatic crustal boundary in eastern North America that is deeply buried beneath the Appalachian basin. Data not in the original aeromagnetic data set, particularly the lack of any information available at the time to constrain the southern continuation of the anomaly southwest of Tennessee, left the source of the lineament open to conjecture. We use modern digital aeromagnetic maps to fill in these data gaps and, for the first time, constrain the southern termination of the NY-AL lineament . Our analysis indicates that the lineament reflects a crustal-scale, right-lateral strike-slip fault that has displaced anomalies attributed to Grenville orogenesis by ~220 km. Palinspastic restoration of this displacement rearranges the trace of the Grenville belt in southern Rodinia and implies only passive influence on later-formed Appalachian structures. The precise timing of dextral movement on the NY-AL structure is not resolvable from the existing data set, but it must have occurred during one of, or combinations of, the following events: (1) a late, postcontractional (post-Ottawan) stage of the Grenville orogeny; (2) late Neoproterozoic to Cambrian rifting of Laurentia; or (3) right-slip reactivation during the late Neoproterozoic-Cambrian rifting of Laurentia, or during Appalachian movements. Our palinspastic reconstruction also implies that the host rocks for modern earthquakes in the Eastern Tennessee Seismic Zone are metasedimentary gneisses, and it provides an explanation for the spatial location and size of the seismic zone. © 2010 Geological Society of America.

New York, Pennsylvania, Ohio, Kentucky, Tennessee,↗
USGS2008

Stratigraphic framework of Cambrian and Ordovician rocks in the Appalachian Basin from Sequatchie County, Tennessee through eastern Kentucky, to Mingo County, West Virginia

Cross section H-H' is the seventh in a series of restored cross sections constructed by the lead author to show the stratigraphic framework of Cambrian and Ordovician rocks in the Appalachian basin from Pennsylvania to Tennessee. The sections show complexly intertongued carbonate and siliciclastic lithofacies, marked thickness variations, key marker horizons, unconformities, stratigraphic nomenclature of the Cambrian and Ordovician sequence, and major faults that offset Proterozoic basement and overlying lower Paleozoic rocks. Several of the drill holes along the cross section have yielded a variety of whole and (or) fragmented conodont elements. The identifiable conodonts are used to differentiate strata of Late Cambrian, Early Ordovician, and Middle Ordovician age, and their conodont color alteration index (CAI) values are used to establish the thermal maturity of the sequence. Previous cross sections in this series are G-G', F-F', E-E', D-D', C-C', and B-B'. Many of these cross sections (B-B', C-C', D-D', and G-G') have been improved with the addition of gamma-ray log traces, converted to digital images, and made accessible on the Web.

Kentucky, Tennessee, Virginia, West Virginia↗
USGS2006

Stratigraphic framework and depositional sequences in the Lower Silurian regional oil and gas accumulation, Appalachian Basin: From Licking County, Ohio, to Fayette County, West Virginia

The Lower Silurian regional oil and gas accumulation was named by Ryder and Zagorski (2003) for a 400-mile (mi)-long by 200-mi-wide hydrocarbon accumulation in the central Appalachian basin of the Eastern United States and Ontario, Canada. From the early 1880s to 2000, approximately 300 to 400 million barrels of oil and eight to nine trillion cubic feet of gas have been produced from the Lower Silurian regional oil and gas accumulation (Miller, 1975; McCormac and others, 1996; Harper and others, 1999). Dominant reservoirs in the regional accumulation are the Lower Silurian "Clinton" and Medina sandstones in Ohio and westernmost West Virginia and coeval rocks in the Lower Silurian Medina Group (Grimsby Sandstone (Formation) and Whirlpool Sandstone) in northwestern Pennsylvania and western New York. A secondary reservoir is the Upper Ordovician(?) and Lower Silurian Tuscarora Sandstone in central Pennsylvania and central West Virginia, a more proximal eastern facies of the "Clinton" sandstone and Medina Group (Yeakel, 1962; Cotter, 1982, 1983; Castle, 1998). The Lower Silurian regional oil and gas accumulation is subdivided by Ryder and Zagorski (2003) into the following three parts: (1) an easternmost part consisting of local gas-bearing sandstone units in the Tuscarora Sandstone that is included with the basin-center accumulation; (2) an eastern part consisting predominantly of gas-bearing "Clinton" sandstone-Medina Group sandstones that have many characteristics of a basin-center accumulation (Davis, 1984; Zagorski, 1988, 1991; Law and Spencer, 1993); and (3) a western part consisting of oil- and gas-bearing "Clinton" sandstone-Medina Group sandstones that is a conventional accumulation with hybrid features of a basin-center accumulation (Zagorski, 1999). With the notable exception of the offshore part of Lake Erie (de Witt, 1993), the supply of oil and (or) gas in the hybrid-conventional part of the regional accumulation continues to decline because of the many wells drilled there since the late 1880s. However, new gas and local oil continues to be discovered in the deeper basin-center part (Zagorski, 1991; Pees, 1994; Petroleum Information Corporation, 1994). In general, only small quantities of gas have been produced from the Tuscarora Sandstone fields because of their generally poor reservoir quality and because of the low energy (Btu) content of the gas (Avary, 1996). Although fracture porosity is the dominant porosity type in the Tuscarora Sandstone gas reservoirs (Avary, 1996), there are several fields, such as Indian Creek, where intergranular porosity seems to be important (Bruner, 1983; Castle and Byrnes, 2005). In order to better understand the character and origin of the Lower Silurian regional oil and gas accumulation and its component parts, six cross sections were drawn through the Lower Silurian strata in parts of New York, Ohio, Pennsylvania, and West Virginia. The locations of all six cross sections are shown on sheet 2 (figs. 1 and 2) of this report. Each cross section shows the stratigraphic framework, depositional setting, sequence stratigraphy, and hydrocarbon-producing intervals of the Lower Silurian sandstone reservoirs and adjoining strata. Cross section F–F′ presented here is about 215 mi long and trends northwestward, approximately normal to the depositional strike of the Lower Silurian sandstone system, and extends through large stretches of the basin-center and hybrid-conventional parts of the Lower Silurian regional oil and gas accumulation.

Ohio, West Virginia↗
USGS2004

Assessment of Appalachian Basin oil and gas resources: Carboniferous Coal-bed Gas Total Petroleum System

The Carboniferous Coal-bed Gas Total Petroleum System, lies within the central and northern parts of the Appalachian coal field. It consists of five assessment units (AU): the Pocahontas Basin in southwestern Virginia, southern West Virginia, and eastern Kentucky, the Central Appalachian Shelf in Tennessee, eastern Kentucky and southern West Virginia, East Dunkard (Folded) in western Pennsylvania and northern West Virginia, West Dunkard (Unfolded) in Ohio and adjacent parts of Pennsylvania and West Virginia, and the Appalachian Anthracite and Semi-Anthracite AU in Pennsylvania and Virginia. Of these, only the Pocahontas Basin and West Dunkard (Folded) AU were assessed quantitatively by the U.S. Geological survey in 2002 as containing about 3.6 and 4.8 Tcf of undiscovered, technically recoverable gas, respectively (Milici and others, 2003). In general, the coal beds of this Total Petroleum System, which are both the source rock and reservoir, were deposited together with their associated sedimentary strata in Mississippian and Pennsylvanian (Carboniferous) time. The generation of biogenic (microbial) gas probably began almost immediately as the peat deposits were first formed. Microbial gas generation is probably occurring at present to some degree throughout the basin, where the coal beds are relatively shallow and wet. With sufficient depth of burial, compaction, and coalification during the late Paleozoic and Early Mesozoic, the coal beds were heated sufficiently to generate thermogenic gas in the eastern part of the Appalachian basin. Trap formation began initially with the deposition of the paleopeat deposits during the Mississippian, and continued into the Late Pennsylvanian and Permian as the Appalachian Plateau strata were deformed during the Alleghanian orogeny. Seals are the connate waters that occupy fractures and larger pore spaces within the coal beds as well as the fine-grained siliciclastic sedimentary strata that are intercalated with the coal. The critical moment for the petroleum system occurred during this orogeny, when deformation created geologic structures in the eastern part of the basin that enhanced fracture porosity within the coal beds. In places, burial by thrust sheets (thrust loading) within the Appalachian fold-and-thrust belt may have resulted in additional generation of thermogenic CBM in the anthracite district of Pennsylvania and in the semianthracite deposits of Virginia and West Virginia.

Kentucky, Ohio, Pennsylvania, Virginia, West Virgi↗