Search USGSSearch

Geology topics

Groundwater & aquifers

Find USGS groundwater and aquifer publications. Search an aquifer name or place, compare source-supplied dates and open reports for hydrogeology, recharge and water-level studies.

351 records · Page 3Linked to original sources

Status and understanding of groundwater quality in the San Joaquin Valley Kern County subbasin domestic-supply aquifer study unit, 2022—California GAMA Priority Basin Project

The quality of water accessed by domestic wells (here referred to as domestic groundwater resources) in the San Joaquin Valley Kern County subbasin (basin number 5-022.14) was assessed as part of the California Groundwater Ambient Monitoring and Assessment (GAMA) Program Priority Basin Project (GAMA-PBP), in cooperation with the California State Water Resources Control Board. Kern County is at the southern end of the San Joaquin Valley in California, and about 30,000 residents are estimated to use privately owned domestic wells for drinking water. Domestic wells typically draw from shallower parts of the aquifer system than public-supply wells and can be more vulnerable to effects from surface activities. Kern County is host to a highly productive agricultural industry, with Bakersfield as the main urban center. The Kern River runs through Bakersfield from the southern Sierra Nevada and intersects the Kern Water Bank, one of the largest groundwater banking operations in California, at the Kern River Intertie. The section of the Kern River running through the Kern Water Bank is dry most years. Kern County also encompasses some of the most productive oil and gas basins in California, with extensive underground and surface disposal of oil-field wastewater. This study was based on data collected from 33 sites sampled by the U.S. Geological Survey for the GAMA-PBP in 2022. To provide context for the water quality assessment, measured concentrations were compared to regulatory and non-regulatory health-based and aesthetic benchmarks. A grid-based method was used to estimate the proportions of the groundwater resources used for domestic-supply wells that have water-quality constituents below (low relative concentration), approaching (moderate relative concentration), or above (high relative concentration) benchmark concentrations. At least one measured constituent with a regulatory benchmark was categorized as having a high relative concentration in 72 percent of the aquifer area used for domestic groundwater resources. Inorganic constituents were detected at high concentrations in 45 percent of the domestic groundwater resources, and the constituents detected above regulatory benchmarks were arsenic, nitrate, and uranium. At least one organic constituent was detected at high concentrations in 41 percent of the domestic groundwater resources, and the constituents exceeding regulatory benchmarks were the fumigants 1,2,3-trichloropropane (1,2,3-TCP), 1,2-dibromo-3-chloropropane (dibromochloropropane [DBCP]), 1,2-dibromoethane (EDB), and the per-and polyfluoroalkyl substance (PFAS) perfluorooctanesulfonate. The disinfection by-product chloroform, the fumigant 1,2-dichloropropane, the herbicides atrazine and hexazinone, and the herbicide degradates 2-chloro-6-ethylamino-4-amino-s-triazine, 2-chloro-4,6-diamino-s-triazine, 4-hydroxychlorothalonil, and metolachlor sulfonic acid were detected in more than 10 percent of domestic groundwater resources, but concentrations did not exceed regulatory benchmarks. Land use, groundwater age (fraction of modern water and mean age), and geochemical environment (oxic or anoxic conditions, pH, alkalinity) were associated with the distribution of high relative concentrations of inorganic and organic constituents. Young, oxygenated water is recharged along the Kern River and adjacent recharge ponds, or as irrigation water in the agricultural areas. High concentrations of nitrate and volatile organic compounds occurred in the oxic water in urban and agricultural areas. The fumigants 1,2,3-TCP, DBCP, and EDB were reported throughout the agricultural areas, whereas chloroform, tetrachloroethene, and PFAS were associated with urban land use. High uranium concentrations were associated with young, modern groundwater in agricultural areas with low pH and high bicarbonate. Total dissolved solids increased with distance from the Kern River, as the contributions of fresh, oxic water decreased. High concentrations of arsenic were present in older anoxic or alkaline groundwater away from areas of recharge. Overall, groundwater age, redox conditions, and the source of recharge as a result of different land uses contribute to large aquifer-scale portions of domestic groundwater resources that exceed health-based benchmarks for nitrate, uranium, and fumigant concentrations.

California

Hydrogeology, groundwater salinity distributions, and assessment of the effect of oil-production activities on groundwater in the Midway Valley area, western Kern County, San Joaquin Valley, California

This study seeks to determine the effects of oil field produced water disposal operations and well mechanical integrity issues on groundwater quality in oil fields in the southwest San Joaquin Valley, California. Whereas previous studies used groundwater wells to study shallow aquifers outside the oil fields, this study demonstrates that future approaches may use oil well geophysical logs to map groundwater head gradients, create salinity profiles and document changes in salinity over time in oil field areas with sparse groundwater well data and at depths greater than 330 m. We also incorporate an analysis of well histories to determine potential effects of compromised wellbore seals on changes in aquifer quality that cannot be explained by water disposal practices. Water quality in the aquifers is naturally brackish across most of the area, with better quality groundwater occurring in the eastern part. Geophysical logs are used to determine salinity variations within aquifers including the depth at which TDS exceeds 10,000 mg/L. This depth ranges from 366 m in the northwest to approximately 1,500 m in the southeast. Oil well porosity logs are used to determine water table elevations. These logs indicate the water table slopes south-southeast, showing the predominant groundwater flow direction is from oil field disposal areas toward better quality groundwater east of the oil fields. Geophysical logs show formation resistivity near some disposal facilities has decreased over time, indicating the salinity of the aquifer has increased due to disposal of saline produced water in injection wells and ponds. Oil well history analysis suggests that increased salinity over time in water-saturated sand intervals >1.5 km from disposal facilities may be caused by mechanical failures and/or incomplete borehole seals in poorly constructed or abandoned wellbores prevalent throughout the study area—particularly wells drilled prior to 1930.

California

Evaluation of models for estimating hydraulic conductivity in glacial aquifers from NMR logging

Nuclear magnetic resonance (NMR) logging is a promising method for estimating hydraulic conductivity ( K ). During the past ∼60 years, NMR logging has been used for petroleum applications, and different models have been developed for deriving estimates of permeability. These models involve calibration parameters whose values were determined through decades of research on sandstones and carbonates. We assessed the use of five models to derive estimates of K in glacial aquifers from NMR logging data acquired in two wells at each of two field sites in central Wisconsin, USA. Measurements of K , obtained with a direct push permeameter (DPP), K DPP , were used to obtain the calibration parameters in the Schlumberger-Doll Research, Seevers, Timur-Coates, Kozeny-Godefroy, and sum-of-echoes (SOE) models so as to predict K from the NMR data; and were also used to assess the ability of the models to predict K DPP . We obtained four well-scale calibration parameter values for each model using the NMR and DPP measurements in each well; and one study-scale parameter value for each model by using all data. The SOE model achieved an agreement with K DPP that matched or exceeded that of the other models. The Timur-Coates estimates of K were found to be substantially different from K DPP . Although the well-scale parameter values for the Schlumberger-Doll, Seevers, and SOE models were found to vary by less than a factor of 2, more research is needed to confirm their general applicability so that site-specific calibration is not required to obtain accurate estimates of K from NMR logging data.

Wisconsin

Iodine-129 in the eastern Snake River Plain aquifer at and near the Idaho National Laboratory, Idaho, 2021–22

Between the 1950s and 1980s, wastewater generated at the Idaho National Laboratory contained Iodine-129 ( 129 I); this wastewater was discharged directly into the eastern Snake River Plain (ESRP) aquifer through a deep disposal well, unlined infiltration ponds, or leaked from distribution systems below industrial facilities. During 2021–22, the U.S. Geological Survey, in cooperation with the U.S. Department of Energy and the Idaho Department of Environmental Quality Idaho National Laboratory Oversight Program, collected groundwater samples from 64 monitoring wells in the ESRP aquifer, 6 of which are part of a multilevel monitoring system, to determine the concentration of 129 I in the groundwater. These samples were analyzed by accelerator mass spectrometry as part of a long-term ongoing study to track trends and occurrences of this carcinogenic, long-lived radionuclide in the environment. Concentrations ranged from slightly above the locally determined background concentration of 5.4×10 −6 picocuries per liter, to just below the U.S. Environmental Protection Agency’s maximum contaminant level of 1 picocurie per liter. Discharge of wastewater containing 129 I has been discontinued to the aquifer, and long-term trends from a subset (n=15) of sampled wells show decreasing 129 I concentrations over the last three decades. Concentrations of 129 I in groundwater from monitoring wells near facilities at the Idaho National Laboratory are affected by episodic recharge from an ephemeral surface-water source and by the fracture-flow dominated hydrologic regime in the ESRP aquifer. The spatially focused sampling effort has also identified a low-level 129 I plume that affects long-term water quality near and downgradient from the Advanced Test Reactor Complex in the southwestern part of the facility that had not been clearly defined in previous sampling efforts, although the definition of the plume is somewhat limited by available data.

Idaho

Tapwater exposures, residential risk, and mitigation in a PFAS-impacted-groundwater community

Tapwater (TW) safety and sustainability are priorities in the United States. Per/polyfluoroalkyl substance(s) (PFAS) contamination is a growing public-health concern due to prolific use, widespread TW exposures, and mounting human-health concerns. Historically-rural, actively-urbanizing communities that rely on surficial-aquifer private wells incur elevated risks of unrecognized TW exposures, including PFAS, due to limited private-well monitoring and contaminant-source proliferation in urbanizing landscapes. Here, a broad-analytical-scope TW-assessment was conducted in a hydrologically-vulnerable, Mississippi River alluvial-island community, where PFAS contamination of the shallow-alluvial drinking-water aquifer has been documented, but more comprehensive contaminant characterization to inform decision-making is currently lacking. In 2021, we analyzed 510 organics, 34 inorganics, and 3 microbial groups in 11 residential and community locations to assess (1) TW risks beyond recognized PFAS issues, (2) day-to-day and year-to-year risk variability, and (3) suitability of the underlying sandstone aquifer as an alternative source to mitigate TW-PFAS exposures. Seventy-six organics and 25 inorganics were detected. Potential human-health risks of detected TW exposures were explored based on cumulative benchmark-based toxicity quotients ( ∑ TQ ). Elevated risks ( ∑ TQ ≥ 1) from organic and inorganic contaminants were observed in all alluvial-aquifer-sourced synoptic samples but not in sandstone-aquifer-sourced samples. Repeated sampling at 3 sites over 52–55 h indicated limited variability in risk over the short-term. Comparable PFAS-specific ∑ TQ for spatial-synoptic, short-term (3 days) temporal, and long-term (3 years quarterly) temporal samples indicated that synoptic results provided useful insight into the risks of TW-PFAS exposures at French Island over the long-term. No PFAS detections in sandstone-aquifer-sourced samples over a 3 year period indicated no PFAS-associated risk and supported the sandstone aquifer as an alternative drinking-water source to mitigate community TW-PFAS exposures. This study illustrated the importance of expanded contaminant monitoring of private-well TW, beyond known concerns (in this case, PFAS), to reduce the risks of a range of unrecognized contaminant exposures.

Wisconsin

Hydraulic conductivity and transmissivity estimates from slug tests in wells within the Mississippi Alluvial Plain, Arkansas and Mississippi, 2020

During the spring and summer of 2020, the U.S. Geological Survey conducted single-well slug tests on selected observation wells within the Mississippi Alluvial Plain in Arkansas and Mississippi to estimate hydraulic conductivity and transmissivity values for the Mississippi River Valley alluvial and middle Claiborne aquifers. Well and aquifer data were collected from field measurements, well-construction reports, and published aquifer-thickness information. A total of 324 slug-in and slug-out tests were conducted on 48 wells by using mechanical slugs to displace the water column and submersible pressure transducers to record changes in water levels in the wells. Hydraulic conductivity of the aquifers in which the wells are screened was estimated by curve fitting the water-level-change data using aquifer test analysis software. Estimates of aquifer transmissivity were made by multiplying the estimated hydraulic conductivity value by the aquifer thickness at well locations. Mean hydraulic conductivity estimates for 44 observation wells screened in the Mississippi River Valley alluvial aquifer range from 3 to 401 feet per day, and mean transmissivity estimates range from 285 to 80,559 feet squared per day. Mean hydraulic conductivity estimates for four observation wells screened in units of the middle Claiborne aquifer range from 0.14 to 183 feet per day, and mean transmissivity estimates range from 55 to 67,913 feet squared per day. The results from these tests can be used to improve the understanding of water availability and groundwater migration, to refine groundwater models, and to ultimately provide stakeholders and decisionmakers better information for management of the groundwater resources within the Mississippi Alluvial Plain.

Arkansas, Mississippi

Assessment of water levels, nitrate, and arsenic in the Carson Valley Alluvial Aquifer and the development of a data visualization tool for the Carson River Basin, Nevada

Residents of Carson Valley, Douglas County, Nevada, rely on the basin-fill alluvial aquifer underlying the valley for drinking water. Since the 1980s, groundwater levels and water-quality data have been collected to monitor the status of the aquifer system and to assist in planning efforts to address current (2024) and future demand. The U.S. Geological Survey (USGS), in cooperation with Douglas County, Nevada, evaluated trends in water levels, nitrate, and arsenic concentrations from a network of monitoring and domestic wells in Carson Valley. This work also assessed the monitoring well network to determine the suitability of wells for characterizing the occurrence of arsenic in the groundwater. Monitoring of constituents, such as nitrate and arsenic concentrations, is needed to assess changes in contaminant distribution and to evaluate the effect that changing land use and groundwater pumping has on their occurrence and transport. Results of the trend analysis indicate water levels are declining ( p <0.05) in 17 of 26 selected monitoring wells (65 percent). Areas with the largest change in water levels, with more than 20 feet of declines, were within the community areas of Johnson Lane, Ruhenstroth, South Agricultural, East Valley, and Fish Springs. Variations in water levels measured in wells from the Central Agricultural, Minden, Foothill, Alpine County (one well), and Gardnerville Ranchos areas show periods of increase and decrease over time, but they also maintain long-term declining trends ( p <0.05). Increases in nitrate concentrations in groundwater samples collected from 9 out of 14 selected monitoring wells (64 percent) are statistically significant ( p <0.05) within the Ruhenstroth, Gardnerville Ranchos, East Valley, Genoa, and Johnson Lane community areas. Samples collected from a well in Indian Hills/Jacks Valley indicated a decreasing trend in nitrate concentration over time. Nitrate concentrations in samples collected from wells in East Valley, Genoa, Johnson Lane, and Indian Hills/Jack Valley were consistently low (less than 3 milligrams per liter [mg/L]) and stable. Nitrate concentrations from selected wells in Johnson Lane and Garnerville Ranchos exceeded the U.S. Environmental Protection Agency (EPA) maximum contaminant level (MCL) of 10 mg/L (as nitrogen) and have trends that are increasing over time. In 2022, a sample collected from Johnson Lane had a concentration (7.3 mg/L) below the MCL with an increasing trend over time. Temporal trend analyses for groundwater arsenic concentrations in Carson Valley could not be done because of a lack of temporal data. However, using available historical data, arsenic concentrations seem to be greater in groundwater from wells located on the eastern and northern areas of the valley than in wells located on the western or southern areas. Groundwater arsenic concentrations exceed 5 micrograms per liter (μg/L) in most samples collected from wells in Johnson Lane, Airport, Central Agricultural, and East Valley areas and in many cases exceed the U.S. Environmental Protection Agency (EPA) MCL of 10 μg/L. Data indicate that groundwater from domestic wells screened at deeper intervals are likely more vulnerable to elevated arsenic concentrations than shallower wells. A groundwater network evaluation for Carson Valley identified potential modifications in the sampling locations and frequency to better understand the effect of groundwater pumping in communities where municipal and domestic demand are greatest, potentially enhancing understanding of contaminant transport in these areas. Potential modifications to the active well network include reducing the frequency of sample collection from existing network wells (6 out of 11) that have consistently shown low and stable nitrate concentrations, adding wells in areas where data are sparse, and increasing the number of wells in areas with elevated groundwater nitrate concentrations. Including the analysis of arsenic in samples from the active groundwater monitoring well network will provide more detail on the temporal and spatial variability of arsenic concentrations. A visualization tool for the Carson River Basin was developed to provide access to discrete and near real-time hydrologic and water-quality data. The Carson River Basin Hydro Mapper (CBH; U.S. Geological Survey, 2023b) shows active and historical discrete water levels measured by the USGS and the State of Nevada Division of Water Resources, discrete groundwater nitrate and arsenic concentration data collected by the USGS, near real-time streamflow, and surface water levels for select waterbodies. The hydrologic data in the CBH provides resource managers, the public, and the scientific community with an easily accessible tool to present and communicate the most up-to-date information available about local and basin-wide water resources.

Nevada

Top Elevation of Glacial Till and Thickness of the Big Sioux Aquifer Delineated From Electrical Resistivity Tomography Surveys Near Sioux Falls, South Dakota, 2022 and 2025

The City of Sioux Falls, South Dakota, requested the U.S. Geological Survey perform electrical resistivity surveys on three parcels of land north of the city. Electrical resistivity data were collected along a total of 22 transects during March 14–18, 2022, and November 17–21, 2025. Results from electrical resistivity surveys were used to delineate the top of glacial till deposits for the purpose of characterizing the Big Sioux aquifer near the city. Delineating geologic contacts provides important information on groundwater storage, flow dynamics, well design and placement, contaminant transport, groundwater–surface-water interactions, and regional water modeling. The top elevation of glacial till and the thickness of the Big Sioux aquifer varied among the three survey areas. The interpreted top elevation of glacial till in the North survey area decreases from east to west toward a slough, with elevations ranging from 1,403 to 1,418 feet (ft). The estimated thickness of the Big Sioux aquifer in the North survey area increased from east to west, with thicknesses ranging from 23 to 38 ft. The top elevation of glacial till in the Well 72 survey area generally decreases from northwest to southeast. Top elevations of the glacial till in the Well 72 survey area ranged from 1,400 to 1,409 ft along the southern end of transect W72_2. The estimated thickness of the Big Sioux aquifer in the Well 72 survey area was greatest along a southeast to northwest trending channel, with thicknesses ranging from 28 to 40 ft. The top elevation of glacial till in the Nose survey area generally decreases west toward the Big Sioux River. Top elevations of the glacial till in the Nose survey area ranged from 1,362 to 1,395 ft. The estimated thickness of the Big Sioux aquifer in the Nose survey area ranged from 33 to 70 ft.

South Dakota

A new groundwater energy transport model for the MODFLOW hydrologic simulator

Heat transport in the subsurface is an important aspect of research related to the effects of a warming climate on ecological services (i.e., cold-water refugia); the development of geothermal resources for energy banking schemes (i.e., aquifer thermal energy storage [ATES]); and the effects of temperature on other aspects of groundwater quality, such as nutrient cycling. Historically, simulation of heat transport using the MODFLOW groundwater simulator and related codes was performed by scaling the input parameters of a solute-transport model to emulate heat transport. However, that approach required additional pre- and post-processing of input and output and could not account for the variation in effective thermal storage and transport properties during transient, unsaturated flow, for example. True heat-transport capabilities in the context of MODFLOW were first introduced in a variant called USG-Transport. More recently, a new groundwater energy-transport (GWE) model type has been added to MODFLOW 6, the core version of the MODFLOW hydrologic simulator. GWE supports the simulation of heat transport on structured or unstructured grids as well as within and between features of advanced packages that represent streams, lakes, multi-aquifer wells, and the unsaturated zone. GWE is integrated within MODFLOW 6 and is accessible through the FloPy Python package and the MODFLOW 6 application programming interface (API). An example simulation demonstrates conduction between grid cells through both the water and the solid aquifer material, including thermal bleeding from saturated overburden cells into a groundwater flow field.

Groundwater

Water-withdrawal and groundwater-level fluctuations, physical and infiltration characteristics of Ohio River sediment, and isotope-based estimates of water sources relative to a riverbank filtration system in an alluvial aquifer, Louisville, Kentucky, 2000–20

The U.S. Geological Survey and the Louisville Water Company, from 2000 to 2020, cooperatively investigated physical and hydrologic conditions in the Ohio River alluvial aquifer and adjacent riverbed sediments in the northeast part of Louisville, Kentucky, to increase knowledge of processes affecting water sources to collector wells during operation of a riverbank filtration system (RBF). The RBF, in 2020, included an initial collector well (CW1) completed in 1999 and a tunnel and collector well system (TCWS) composed of four collector wells (CW2–CW5) completed in late 2010 that were connected by a tunnel that routed water to a pumping station and a treatment plant. Daily mean water-withdrawal rates typically ranged from about 10.4 to 20.7 million gallons per day (Mgal/d) from 2005 to 2007, then were cyclic from 2008 to 2010 and ranged from as low as about 9 to 13 Mgal/d in winter-spring months up to about 19 to 20 Mgal/d in summer-autumn months. From 2011 through 2017, peak daily mean water-withdrawal rates from CW2–CW5 fluctuated between winter-spring lows of about 20–30 Mgal/d to summer-autumn peak rates of about 41.6 Mgal/d in 2013 to about 48.2 Mgal/d in 2012. From 2017 to 2020, TCWS peak daily mean water-withdrawal rates decreased from about 45.7 Mgal/d in 2017 to about 37.5 Mgal/d in 2020 and peak daily mean rates from CW1 ranged from about 20.7 Mgal/d in 2020 to about 21.6 Mgal/d in 2018. Periods in 2019–20 with tunnel pumping station daily mean water-withdrawal rates smaller than about 30 Mgal/d had generally stable water levels in CW2 and indicated the sustainable yield of the TCWS collector wells under the prevailing hydrologic conditions. Drawdown during July–August of 2008 and 2009 was associated with CW1, the sole operating collector well. Groundwater-flow directions outside the CW1 cone of depression during July–August of 2008 and 2009 were from areas near the alluvial valley margin toward the Ohio River and in 2009 toward Harrods Creek. Collector wells CW2 through CW5 derived water during 2011–19 surveys from surface-water infiltration, as indicated by drawdown that extended beneath the Ohio River and Harrods Creek. Increases in drawdown toward the alluvial valley margins in July–August of 2013 and 2015, compared with July 2011, indicated less available recharge from those flow directions and decreased yield of groundwater from the aquifer after progressively longer TCWS water withdrawals. Drawdown at CW2–CW5 and at observation wells between them lessened in October 2019 and indicated that onshore groundwater levels can recover when collector well withdrawals decrease. Overlapping cones of depression in 2011–15 potentiometric surfaces centered around CW2, CW3, CW4, and CW5, and drawdown along divides between those wells indicated well interference between collector wells. Well-interference effects increased during 2013 and 2015 survey periods, despite decreased water-withdrawal rates compared with July 2011, and expanded to include CW1 when its use resumed. Groundwater-level fluctuations in observation wells near the Ohio River were consistent with gradual depletion of groundwater yield during tunnel pumping station operation at river elevations of about 420 feet above the National Geodetic Vertical Datum of 1929 (NGVD 29) and enhanced recharge of the aquifer when river elevations were above flood stage of about 430 feet above NGVD 29. Groundwater-level declines in observation wells near the Ohio River were most apparent in summer and some autumn months between 2012 and 2017 during periods when tunnel pumping station mean daily water-withdrawal rates were about 35 Mgal/d or more. Periods of relatively stable groundwater levels during 2019–20 in observation wells between CW2–CW5, when tunnel pumping station water-withdrawal rates were about 30–33 Mgal/d or less, also indicated that the prevailing sustainable yield was about 30 Mgal/d or less. Wells associated with CW3 and CW4 had the largest increases in slopes of best-fit lines relating water-level difference to water-withdrawal rate between 2012 and 2020, an indication of decreased efficiencies of those wells to supply water or of changes in groundwater yield around the well. Increased slopes of best-fit lines relating water-level difference to water-withdrawal rate from 2019 to 2020, when groundwater levels were otherwise relatively stable, also indicated that the specific capacity of one or more TCWS collector wells may have declined during that period. Riverbed surface elevation, roughness, and hardness changes between hydroacoustic surveys indicated active accretion and erosion of bed sediment offshore from the riverbank filtration system in 2002–4. Riverbed hydraulic conductivity computed from 2013 to 2015 in tests at 11 sites ranged from 0.2 to 230 feet per day. Ten temporary piezometer sites with adjacent operating collector wells had drawdowns that ranged from about 4 to 11.7 feet and hammer blows greater than or equal to 49 counts, which indicated a relatively great density of alluvial sediments and the potential for diminished riverbed infiltration rates. Contributions of Ohio River infiltration to collector wells estimated from deuterium and oxygen-18 isotopic ratios in representative Ohio River and groundwater samples were considerably larger in warmer months than cooler months and ranged from 80–90 percent in CW1–CW5 in May 2020 to 100 percent in May 2019 at CW2, CW4, and CW5. Groundwater contributions to water withdrawals by collector wells increased in cooler autumn months and ranged from 40 percent at CW3 and CW5 in November 2020 to 70 percent at CW2, CW4, and CW5 in November–December 2019. November 2019 and November 2020 isotopic compositions of water from the collector wells had enriched deuterium and oxygen-18 isotopic ratios consistent with mixtures of evaporation-modified water from the Ohio River and meteoric-origin groundwater.

Indiana, Kentucky

Remote sensing-based actual evapotranspiration assessment in a data-scarce area of Brazil: A case study of the Urucuia Aquifer System

The large groundwater reserves of the Urucuia Aquifer System (UAS) enabled agricultural development and economic growth in the western Bahia State, in northeastern Brazil. Over the last several years, concern has grown around the aquifer’s diminishing water levels, and water balance (WB) studies are in demand. Considering the lack of measured actual evapotranspiration (ET a ), a major component of the water cycle, this work uses the Operational Simplified Surface Energy Balance (SSEBop) model to estimate ET a , and compares it to basin-scale estimates from the Soil Moisture Accounting Procedure (SMAP) monthly model and from an annual WB closure method, based on gridded meteorological data and the Gravity Recovery and Climate Experiment (GRACE) product. Additionally, a comparative assessment of different versions of the SSEBop parameterization was performed. Moderate Resolution Imaging Spectroradiometer (MODIS) imagery was used to implement eight different versions of the SSEBop algorithm over the UAS between 2000 and 2013. SSEBop and SMAP ET a yielded similar seasonal patterns, with correlation coefficient (r) up to 0.65, mean difference (MD) of 0.8 mm/month and mean absolute difference (MAD) of 18.5 mm/month. Comparison of SSEBop annual ET a estimates to annual SMAP and WB closure estimates yielded low MD (12.1 and −7.3 mm/year, respectively) and MAD (82.5 and 82.8 mm/year, respectively), but also low r values (0.00 and 0.37, respectively). The comparison of the different SSEBop versions indicated the need to incorporate a calibration step of the aerodynamic heat resistance (r ah ) parameter. SSEBop results were also used for land cover and drought monitoring. Analysis indicates that agriculture, associated with an increasing trend of atmospheric evaporative demand, is responsible for the decrease in groundwater levels and streamflow in the studied time period.

Urucuia Aquifer System

Modeling seawater intrusion along the Alabama coastline using physical and machine learning models to evaluate the effects of multiscale natural and anthropogenic stresses

Seawater intrusion threatens groundwater resources in coastal regions, including southern Baldwin County, Alabama, where the freshwater-saltwater interface dynamics remain poorly understood. To address this gap, this study uses combined physics-based and machine-learning models to quantify seawater intrusion caused by natural (storm surges) and anthropogenic (human activities) perturbations. The long short-term memory network and wavelet analysis were used to assess vertical aquifer vulnerabilities, revealing that the shallow part of the Coastal lowlands aquifer system (CL1) in the southern Baldwin County region is more susceptible to sea level rise and groundwater extraction than deeper aquifers. Based on these findings, a cross-sectional numerical model (physics approach) for the CL1 aquifer was developed to evaluate tidal and storm surge effects, using Tropical Storm Claudette (June 2021) as a case study. Results showed that tidal fluctuations had a minimal impact on the saltwater-freshwater interface location, whereas storm surges caused substantial inland movement, with effects lasting for nine months. The steady-state version of the three-dimensional (3D) physical model predicted seawater intrusion across the entire area, and convolutional neural network-based modeling further validated the model results. The 3D physical model was also applied to a smaller area to assess human impact on the saltwater interface due to two groundwater pumping scenarios (± 50% of the baseline pumping rate). Results revealed that a 50% increase in groundwater withdrawals caused seawater to advance ~ 320 m inland, whereas a 50% reduction led to a ~ 270-meter retreat. This study highlights the vulnerability of Alabama’s shallow coastal aquifers to seawater intrusion due to storm surges and human activities, and demonstrates that combining physics-based models with machine learning approaches can improve groundwater predictions, though its accuracy depends on the availability of site-specific data.

Alabama

Status of water-level altitudes and long-term and short-term water-level changes in the Chicot and Evangeline (undifferentiated) and Jasper aquifers, greater Houston area, Texas, 2024

Since the early 1900s, groundwater withdrawn from the primary aquifers that compose the Gulf Coast aquifer system—the Chicot, Evangeline, and Jasper aquifers—has been an important source of water in the greater Houston area, Texas. This report, prepared by the U.S. Geological Survey in cooperation with the Harris-Galveston Subsidence District, City of Houston, Fort Bend Subsidence District, Lone Star Groundwater Conservation District, and Brazoria County Groundwater Conservation District, is one in an annual series of reports depicting the status of water-level altitudes and water-level changes in these aquifers in the greater Houston area. In this report, the Chicot and Evangeline aquifers are treated as a single aquifer for the purposes of providing annual assessments of regional-scale water-level altitudes and water-level changes over time. In 2024, shaded depictions of estimated water-level altitudes for the Chicot and Evangeline aquifers (undifferentiated) ranged from about 301 feet (ft) below the North American Vertical Datum of 1988 (NAVD 88) to about 184 ft above NAVD 88. The largest decline in water-level altitudes depicted by the 1977–2024 long-term water-level-change map was in south-central Montgomery County. In comparison, the 1990–2024 long-term water-level-change map depicts the largest declines in water-level altitudes in an area northwest of The Woodlands and in an area of northern Waller County. The largest rise in water-level altitudes for 1977–2024 is depicted in an area of east-central Harris County, whereas the largest rise in water-level altitudes for 1990–2024 is depicted in an area of central Harris County. The 5-year short-term water-level-change map depicts the largest declines in several parts of the study area, but these declines are concentrated primarily in northern Fort Bend County, southwestern Harris County, and south-central Montgomery County. The largest rise for 2019–24 is depicted at a well in northern Fort Bend County. The 1-year short-term water-level-change map depicts the largest declines at a well in northern Fort Bend County and a well in west-central Harris County. The largest rise for 2023–24 is depicted at a well in east-central Fort Bend County. In 2024, shaded depictions of estimated water-level altitudes for the Jasper aquifer ranged from about 255 ft below NAVD 88 to about 321 ft above NAVD 88. The 2000–24 long-term water-level-change map depicts the largest water-level decline in an area of central San Jacinto County; the largest rise is depicted in an area of central Grimes County. The 5-year short-term water-level-change map depicts the largest declines across parts of central and southern Montgomery County and at one well in north-central Harris County. The largest rise for 2019–24 is depicted at a well centered on the Montgomery-Grimes County line. The 1-year short-term water-level-change map depicts the largest declines at two wells in south-central Montgomery County and one well in northwestern Montgomery County on the west side of Lake Conroe. The largest rises during 2023–24 are depicted at one well in northwestern Montgomery County and one well in south-central Montgomery County.

Texas

Quantitative subsurface characterization illuminates the origin of the Quaternary Mississippi River Valley alluvial aquifer

The Mississippi River Valley alluvial aquifer (MRVA) is vital to U.S. food security and global agricultural supply. However, quantitative understanding of its Quaternary origin, architecture, and hydrologic function remains incomplete. Here we develop a three-dimensional hydrostratigraphic model to characterize the deposition of clay and silt, fine-medium sands, and graveliferous sands using lithologic data from 75,000 boreholes compiled across the Lower Mississippi Valley and a geostatistical method—interval kriging. We find that cyclic glacial entrenchments, evidenced by remnants of pre-Wisconsinan postglacial sediments, alongside geodynamic activities shaped the MRVA basal configuration. Stratal weakening from faulting and salt diapirism enhanced glacial incision and thereby produced abrupt aquifer thickening. We demarcate the top of graveliferous sands as the regional marker of the Pleistocene-Holocene transition. The MRVA hydrostratigraphy reveals hydrologic function and geologic controls on groundwater storage and quality, advancing the assessment of aquifer sustainability under a changing climate, with implications for alluvial aquifers globally.

Arkansas, Illinois, Kentucky, Louisiana, Mississip

Assessing nonpoint-source uranium pollution in an irrigated stream-aquifer system

Uranium (U) in rocks and soils of arid and semi-arid environments can be mobilized by irrigation and fertilization, posing environmental and health risks. Elevated U, along with selenium (Se) and nitrate (NO 3 ) co-constituents, necessitates careful monitoring and management. We developed a distributed-parameter numerical model to assess U pollution in an irrigated stream-aquifer system, applying it to a 552 km 2 region in Colorado's Lower Arkansas River Valley (LARV) over 14 years. A MODFLOW model, describing groundwater and stream flow, was coupled with an RT3D-OTIS model to portray reactive U transport. Calibration using the PESTPP-iES iterative ensemble smoother (iES) software indicated good agreement with observed U concentrations. The model revealed substantial and variable U levels across the LARV, highlighting potential hotspots and possible contributing factors, such as geological composition of the bedrock and near-surface shale and aquifer sediments derived from them, irrigation practices, and riparian landscape. U levels exceed the chronic standard (85th percentile = 30 μg/L, set by the US Environmental Protection Agency), which is the permissible regulatory threshold, in groundwater across 44 % of the region and along the river by an average factor of 2.9. Simulated average U concentrations in the non-riparian aquifer and river are 124 μg/L and 60 μg/L, respectively, compared with 112 μg/L and 62 μg/L for measured values. The average 85th percentile U concentration is 222 μg/L in the aquifer and 82 μg/L in the river. Average simulated U mass loading to the river is 0.17 kg/day per km, compared to an estimated 0.23 kg/day per km. Findings provide a baseline for comparing future simulated outcomes of alternative best management practices (BMPs) for U pollution mitigation and offer a methodology applicable to other irrigated regions.

Colorado

Groundwater and surface-water interactions in the Lower Duwamish Waterway, Seattle, Washington

The U.S. Geological Survey (USGS), in cooperation with the Washington State Department of Ecology (Ecology), conducted a study to describe the current understanding of the regional groundwater system of the lower Duwamish River valley and groundwater and surface-water interactions in the lower Duwamish Waterway. The lower Duwamish Waterway is the final 5-mile (mi) reach of the Duwamish River before it empties into Elliott Bay in Puget Sound near Seattle, Washington. A nearshore site (hereinafter referred to as “Nearshore Site” to distinguish the particular site from general discussions of nearshore areas) along the western shoreline of the Duwamish River, about 1.5 mi upstream from the river mouth, was selected for focused groundwater data collection by USGS. Data loggers were deployed in seven groundwater wells and one stilling well in the Duwamish River to measure specific conductance, temperature, and depth at 15-minute intervals for a period of about 2 years. At the Nearshore Site during 2020–22, water levels in the shallow wells were 3–8 feet (ft) higher than water levels in the deep wells, providing evidence for a low-permeability layer between the shallow and deep aquifers in this area. The shallow wells had a pronounced seasonal variability, with high water levels in winter and low water levels in summer. Data from the deep wells showed far less seasonal variability, with slight increases in winter and a near-constant water level from spring to autumn. The deep wells had a strong hydraulic connection to the Duwamish River, as evidenced by the synchronous water-level variability during the tidal cycle, whereas the shallow wells had minimal to no tidal response. The potentiometric maps developed for the Nearshore Site and surrounding areas indicate large differences in groundwater-flow directions for the shallow and deep aquifers at low and high tides. For the shallow aquifer, flow is toward the lower Duwamish Waterway near the Nearshore Site, regardless of the tidal condition. For the deep aquifer, a potentiometric trough forms parallel to the shoreline during high tide, indicating that groundwater flow converges from the uplands to the west and the Duwamish River to the east. The geometry of the potentiometric surfaces between the nearshore-most well and the shoreline is complex and is further confounded by intermittent shoreline armoring and other buried infrastructure, which could serve as either a barrier or a conduit to flow. Groundwater and surface-water interactions in the lower Duwamish Waterway are inherently complex as a result of three overarching factors. First, water levels in the lower reaches of the Duwamish River vary daily by 11–16 ft because of tides from Puget Sound, which create large swings in the hydraulic gradient in the nearshore groundwater system. Second, the density and chemical composition of water in the Duwamish River change daily with the tides and seasonally, which constrains how river water entering the nearshore sediments interacts with discharging groundwater. Third, the nearshore subsurface and shoreline conditions are heterogenous because of extensive shoreline armoring over the past century, which governs the flow of groundwater and infiltrating river water. These unique features of groundwater and surface-water interactions in the lower Duwamish Waterway thus govern the transport of terrestrial contaminants to the lower Duwamish Waterway. Furthermore, the heterogenous aquifer properties in the lower Duwamish Waterway contribute to spatially and temporally dynamic contaminant-transport processes.

Washington

Quality of groundwater used for domestic supply in the Gilroy-Hollister basin and surrounding areas, California, 2022

More than 2 million Californians rely on groundwater from domestic wells for drinking-water supply. This report summarizes a 2022 California Groundwater Ambient Monitoring and Assessment Priority Basin Project (GAMA-PBP) water-quality survey of 33 domestic and small-system drinking-water supply wells in the Gilroy-Hollister Valley groundwater basin and the surrounding areas, where more than 20,000 residents are estimated to utilize privately owned domestic wells. The study area includes the Llagas subbasin in the north, the North San Benito subbasin in the south, and the surrounding uplands. The study was focused on groundwater resources used for domestic drinking-water supply, which are mostly drawn from shallower parts of aquifer systems rather than those of groundwater resources used for public drinking-water supply in the same area. This assessment characterized the quality of ambient groundwater in the aquifer before filtration or treatment, rather than the quality of drinking water delivered to the tap. To provide context, the measured concentrations of constituents in groundwater were compared to Federal and California State regulatory and non-regulatory benchmarks for drinking-water quality. A grid-based method was used to estimate the areal proportions of groundwater resources used for domestic drinking wells that have water-quality constituents present at high concentrations (above the benchmark), moderate concentrations (between one-half of the benchmark and the benchmark for inorganic constituents, or between one-tenth of the benchmark and the benchmark for organic constituents), and low concentrations (less than one-half or one-tenth the benchmark for inorganic and organic constituents, respectively). This method provides statistically representative results at the study-area scale and permits comparisons to other GAMA-PBP study areas. In the study area, inorganic constituents in groundwater were greater than regulatory benchmarks (U.S. Environmental Protection Agency [EPA] or State of California maximum contaminant levels [MCLs]) for public drinking-water quality in 24 percent of domestic groundwater resources. The inorganic constituents present at concentrations greater than MCLs for drinking water were nitrate (as nitrogen), barium, chromium, and selenium. Total dissolved solids (TDS) or manganese were present at concentrations greater than the secondary maximum contaminant levels (SMCLs) that the State of California uses as aesthetic-based benchmarks in 48 percent of domestic groundwater resources. No volatile organic compounds or pesticide constituents were present at concentrations greater than regulatory benchmarks. Total coliform bacteria and enterococci were detected in 4 percent of domestic groundwater resources. Per- and polyfluoroalkyl substances (PFAS) were detected in 19 percent of domestic groundwater resources, and 10 percent had concentrations greater than recently enacted (April 2024) EPA MCLs. Physical and chemical factors from natural and anthropogenic sources that could affect the groundwater quality were evaluated using results from statistical testing of associations between constituent concentrations and potential explanatory variables. In this study, relevant physical factors include well construction characteristics, groundwater age, site proximity to groundwater recharge or discharge zones, and potential sources of contamination. Relevant chemical factors include the initial chemistry of the recharge water, the mineralogy of the aquifer sediments, and the subsequent shifts in chemistry as biologic and geologic reactions alter groundwater in the subsurface. Nitrate concentrations were correlated to agricultural land use, distance from the boundary of the Gilroy-Hollister Valley groundwater basin, and the proportion of modern (post-1950s) water captured by the well. Denitrification under anoxic redox conditions can mitigate some nitrate derived from fertilizer application. Total dissolved solids primarily were derived from water-rock interactions with soils and aquifer materials in the study area, but there were high concentrations where agricultural practices contributed additional TDS. Mineralogy of aquifer sediments and rocks also affect barium, selenium, boron, and chromium concentrations in the Gilroy-Hollister Valley groundwater basin. PFAS were positively correlated with urban land use and the proportion of modern water captured by the well.

California

Analysis of aquifer framework and properties, Alvahs Lane well field, Cutchogue, New York

The U.S. Geological Survey, in cooperation with the Suffolk County Water Authority, evaluated the aquifer transmissivity and storage properties at the Alvahs Lane well field north of the village of Cutchogue, New York. This analysis of aquifer properties provides the Suffolk County Water Authority with hydrogeologic information needed to develop water supplies to meet the increasing water demands of the residents of Suffolk County, New York. An aquifer test was conducted at the Alvahs Lane well field from October 18 through October 21, 2022, when a production well was pumped at 550 gallons per minute for about 24 hours, and groundwater-level drawdown and recovery were measured in two monitoring wells. The three wells are screened in a glaciofluvial aquifer under unconfined (water table) conditions. Drawdown and recovery data were analyzed with an analytical solution for partial penetration and delayed yield in an unconfined aquifer to provide estimates of the glaciofluvial aquifer properties. Inclusion of lateral aquifer boundaries was not necessary for the analysis to result in satisfactory matches with the observed water-level responses. Aquifer transmissivity was estimated at 32,000 feet squared per day. Assuming a saturated aquifer thickness of 120 feet, this result is equivalent to a horizontal hydraulic conductivity value of 270 feet per day. Specific yield was estimated at 0.15 (dimensionless). The estimated properties are consistent with those of a highly transmissive unconfined aquifer.

New York