Search USGS⌕ Search

Geology topics

W.S. Keys

Publications and source records attributed to W.S. Keys.

7 recordsLinked to original sources
USGS2006

Well logging in ground‐water hydrology

In 1966 more than 50 billion gallons of water was pumped daily from an estimated 10 to 15 million water wells in the United States. This was more than one‐sixth of the national withdrawal of water . On the basis of past rates of increase, a much greater future use of ground water is suggested. Our annual investment in water wells is one‐half to three‐quarter billion dollars, not including pumps and plumbing. In 1964 approximately 436,000 new wells were drilled; however, less than 1 percent of these wells were logged by any geophysical means. The application of _ge_o.phy.sical well logging to ground‐water hydrology is comparable to its use in petroleum exploration in the 1930's; however, we can take advantage of equipment and interpretation techniques developed in the oil industry that are available now for use in ground‐water investigations. Although most petroleum well logging techniques may be utilized in hydrology ; modifications in equipment and interpretation are necessary because of basic economic and environmental differences between petroleum and ground‐water evaluation. If logging is to be widely applied to ground‐water exploration and evaluation, the expense of equipment and services must be reduced. Fortunately, this can be accomplished, because most water wells are not as deep as oil wells and the temperatures and pressures are lower. The Water Resources Division of the U. S. Geological Survey is conducting research on the application of borehole geophysics to ground‐water hydrology . The following logging devices are utilized in the evaluation of ground‐water environments: spontaneous potential, resistivity, gamma, gamma‐gamma, neutron, radioactive tracer, flowmeter, caliper, fluid resistivity, gradient and differential temperature, and sonic velocity. Lightweight logging sondes and control modules are operated by one man, either on a vehicle‐mounted 6,000‐foot logger or on a suitcase‐mounted 500‐foot logger. An inexpensive magnetic tape system has been developed and is used routinely for log recording and playback. If commercial well logging service is to be widely used in ground‐water exploration and development, water well contractors, and State and municipal agencies must be educated on the advantages of obtaining more information from each hole drilled. It will be necessary also to demonstrate how well logging can provide much of this information. In addition, the well logging industry must adapt their equipment and services to the requirements of ground‐water hydrology . The need for additional logging capability in this field exists at the present time and is expected to increase. Hopefully industry will be able to fill the gap.

Groundwater↗
USGS1990

Borehole geophysics applied to ground-water investigations

The purpose of this manual is to provide hydrologists, geologists, and others who have the necessary background in hydrogeology with the basic information needed to apply the most useful borehole-geophysical-logging techniques to the solution of problems in ground-water hydrology. Geophysical logs can provide information on the construction of wells and on the character of the rocks and fluids penetrated by those wells, as well as on changes in the character of these factors over time. The response of well logs is caused by petrophysical factors, by the quality, temperature, and pressure of interstitial fluids, and by ground-water flow. Qualitative and quantitative analysis of analog records and computer analysis of digitized logs are used to derive geohydrologic information. This information can then be extrapolated vertically within a well and laterally to other wells using logs. The physical principles by which the mechanical and electronic components of a logging system measure properties of rocks, fluids, and wells, as well as the principles of measurement, must be understood if geophysical logs are to be interpreted correctly. Plating a logging operation involves selecting the equipment and the logs most likely to provide the needed information. Information on well construction and geohydrology is needed to guide this selection. Quality control of logs is an important responsibility of both the equipment operator and the log analyst and requires both calibration and well-site standardization of equipment. Logging techniques that are widely used in ground-water hydrology or that have significant potential for application to this field include spontaneous potential, resistance, resistivity, gamma, gamma spectrometry, gamma-gamma, neutron, acoustic velocity, acoustic televiewer, caliper, and fluid temperature, conductivity, and flow. The following topics are discussed for each of these techniques: principles and instrumentation, calibration and standardization, volume of investigation, extraneous effects, and interpretation and applications.

Techniques of Water-Resources Investigations↗
USGS1988

Borehole geophysics applied to ground-water investigations

The purpose of this manual is to provide hydrologists, geologists, and others who have the necessary training with the basic information needed to apply the most useful borehole-geophysical-logging techniques to the solution of problems in ground-water hydrology. Geophysical logs can provide information on the construction of wells and on the character of the rocks and fluids penetrated by those wells, in addition to changes in the character of these factors with time. The response of well logs is caused by: petrophysical factors; the quality; temperature, and pressure of interstitial fluids; and ground-water flow. Qualitative and quantitative analysis of the analog records and computer analysis of digitized logs are used to derive geohydrologic information. This information can then be extrapolated vertically within a well and laterally to other wells using logs. The physical principles by which the mechanical and electronic components of a logging system measure properties of rocks, fluids and wells, and the principles of measurement need to be understood to correctly interpret geophysical logs. Planning the logging operation involves selecting the equipment and the logs most likely to provide the needed information. Information on well construction and geohydrology are needed to guide this selection. Quality control of logs is an important responsibility of both the equipment operator and log analyst and requires both calibration and well-site standardization of equipment. Logging techniques that are widely used in ground-water hydrology or that have significant potential for application to this field include: spontaneous potential, resistance, resistivity, gamma, gamma spectrometry, gamma-gamma, neutron, acoustic velocity, acoustic televiewer, caliper, and fluid temperature, conductivity, and flow. The following topics are discussed for each of these techniques: principles and instrumentation, calibration and standardization, volume of investigation, extraneous effects, and interpretation and applications.

Open-File Report↗
USGS1985

EFFECTS OF LITHOLOGY ON TELEVIEWER-LOG QUALITY AND FRACTURE INTERPRETATION.

Representative televiewer logs illustrating natural fractures in such common rock types as granite, gabbro, basalt, schist, sandstone, limestone and shale are presented in addition to photographs of the same fractures in core samples. These examples demonstrate the many difficulties in recognizing fractures on televiewer logs compared to fractures in logs because of the vertical scale distortion on televiewer logs and from drilling damage to the fractures at the borehole wall. All of these results demonstrate that significant fracture widening usually occurs during drilling, explaining why fractures described by the core logger as closed can be consistently detected on televiewer logs.

Conference Paper↗
USGS1971

Application of borehole geophysics to water-resources investigations

This manual is intended to be a guide for hydrologists using borehole geophysics in ground-water studies. The emphasis is on the application and interpretation of geophysical well logs, and not on the operation of a logger. It describes in detail those logging techniques that have been utilized within the Water Resources Division of the U.S. Geological Survey, and those used in petroleum investigations that have potential application to hydrologic problems. Most of the logs described can be made by commercial logging service companies, and many can be made with small water-well loggers. The general principles of each technique and the rules of log interpretation are the same, regardless of differences in instrumentation. Geophysical well logs can be interpreted to determine the lithology, geometry, resistivity, formation factor, bulk density, porosity, permeability, moisture content, and specific yield of water-bearing rocks, and to define the source, movement, and chemical and physical characteristics of ground water. Numerous examples of logs are used to illustrate applications and interpretation in various ground-water environments. The interrelations between various types of logs are emphasized, and the following aspects are described for each of the important logging techniques: Principles and applications, instrumentation, calibration and standardization, radius of investigation, and extraneous effects.

Techniques of Water-Resources Investigations↗