Geology topics

Virginia G. Toy

Publications and source records attributed to Virginia G. Toy.

3 recordsLinked to original sources

USGS2022

Electrical properties and anisotropy of schists and fault rocks from New Zealand’s Southern Alps under confining pressure

Magnetotelluric models spanning the Pacific–Australian Plate boundary in New Zealand’s South Island indicate a localized zone of low electrical resistivity that is spatially coincident with theductile mid-crustal part of the Alpine Fault Zone (AFZ). We explored the source of this anomaly bymeasuring the electrical properties of samples collected from surface outcrops approaching the AFZthat have accommodated a gradient of systematic strain and deformation conditions. We investigatedthe effects of tectonite fabric, fluid saturated pore/fracture networks and surface conductivity on the bulk electrical response and the anisotropy of resistivity measured under increasing confining pressures up to 200 MPa. We find that porosity and resistivity increase while porosity and the change in anisotropy of resistivity with confining pressure (δ (ρk/ρ⊥)/δ (peff)) decreases approaching theAFZ, indicating the electrical response is controlled by pore fluid conductivity and modified during progressive metamorphism. Conversely, Alpine mylonites exhibit relatively low resistivities at low porosities, and lower δ (ρk/ρ⊥)/δ (peff) than the schists. These findings indicate a transition in both the porosity distribution and electrical charge transport processes in rocks that have experienced progressive grain size reduction and mixing of phases during development of mylonitic fabrics due to creep shear strain within the AFZ.

Southern Alps↗

USGS2017

Bedrock geology of DFDP-2B, central Alpine Fault, New Zealand

During the second phase of the Alpine Fault, Deep Fault Drilling Project (DFDP) in the Whataroa River, South Westland, New Zealand, bedrock was encountered in the DFDP-2B borehole from 238.5–893.2 m Measured Depth (MD). Continuous sampling and meso- to microscale characterisation of whole rock cuttings established that, in sequence, the borehole sampled amphibolite facies, Torlesse Composite Terrane-derived schists, protomylonites and mylonites, terminating 200–400 m above an Alpine Fault Principal Slip Zone (PSZ) with a maximum dip of 62°. The most diagnostic structural features of increasing PSZ proximity were the occurrence of shear bands and reduction in mean quartz grain sizes. A change in composition to greater mica:quartz + feldspar, most markedly below c. 700 m MD, is inferred to result from either heterogeneous sampling or a change in lithology related to alteration. Major oxide variations suggest the fault-proximal Alpine Fault alteration zone, as previously defined in DFDP-1 core, was not sampled.

New Zealand Journal of Geology and Geophysics↗

USGS2014

Frictional properties of exhumed fault gouges in DFDP-1 cores, Alpine Fault, New Zealand

Principal slip zone gouges recovered during the Deep Fault Drilling Project (DFDP-1), Alpine Fault, New Zealand, were deformed in triaxial friction experiments at temperatures, T , of up to 350°C, effective normal stresses, σ n ′, of up to 156 MPa, and velocities between 0.01 and 3 µm/s. Chlorite/white mica-bearing DFDP-1A blue gouge, 90.62 m sample depth, is frictionally strong (friction coefficient, μ , 0.61–0.76) across all experimental conditions tested ( T = 70–350°C, σ n ′ = 31.2–156 MPa); it undergoes a transition from positive to negative rate dependence as T increases past 210°C. The friction coefficient of smectite-bearing DFDP-1B brown gouge, 128.42 m sample depth, increases from 0.49 to 0.74 with increasing temperature and pressure ( T = 70–210°C, σ n ′ = 31.2–93.6 MPa); the positive to negative rate dependence transition occurs as T increases past 140°C. These measurements indicate that, in the absence of elevated pore fluid pressures, DFDP-1 gouges are frictionally strong under conditions representative of the seismogenic crust.

Alpine Fault↗