Geology topics

Timothy S. Collett

Publications and source records attributed to Timothy S. Collett.

At least 19 recordsLinked to original sources

USGS2026

Production of secondary microbial methane from a gas hydrate-bearing reservoir at the HYDRATE P1 Production Test Well (PTW-1) on the Alaskan North Slope

Gas hydrate in the Alaskan North Slope (ANS) is believed to contain as much methane as the known conventional gas accumulations in the Prudhoe Bay field. The JOGMEC-DOE-USGS Collaborative Gas Hydrate R&D Project conducted an extended-duration production test from the sub-permafrost, gas-hydrate saturated B1 sand reservoir (unit B) at the Kuparuk State 7-11-12 Site in the Prudhoe Bay Unit of the ANS. Using compositional and stable isotopic data measured on gas produced from well cuttings and pressure cores collected from the HYDRATE 02 Geo Data Well (GDW), we differentiate primary microbial, secondary microbial, and trace thermogenic gas sources. The upper part of the well contained predominantly primary microbial methane from near the surface to the SV6 stratigraphic horizon at 1133 ft (345.3 m) measured depth (MD). Below that, the gas composition transitioned to a mixture of mostly primary and secondary microbial methane to near the base of ice-bearing permafrost at 1968 ft (599.8 m) MD. With greater depth to 3558 ft (1084.5 m) MD, which includes the D1 sand (unit D), the B1 sand (unit B), and the base of gas hydrate stability at 3113 ft (948.8 m) MD, the gas composition was greater than 98% secondary microbial methane with the remainder being oil-associated thermogenic gas migrated from the deep Sadlerochit Formation. The unit B vertical gas profile derived from degassed pressure cores demonstrated that gas dissolved in the clay-rich sediment intervals bounding the B1 sand reservoir was distinct from dissolved and hydrate-caged gases in the sand-rich hydrate-bearing reservoir. The HYDRATE P1 Production Test Well (PTW-1) targeted and successfully extracted gas dissociated from hydrate gas in the B1 sand for 151 days when using an electrical submersible pump to depressurize the reservoir with subsequent depressurization achieved through the use of a jet pump. Gas produced from PTW-1 was mostly indistinguishable from the gas compositional profile measured through the B1 sand and generally distinct from dissolved gas in the bounding clay-rich sediments, confirming that the upper and lower bounding units limited infiltration into the reservoir during production. Isolation of the bounding units from the reservoir contributed to the unexpectedly high ratio of production gas to water observed during the extended-duration gas hydrate production test at PTW-1.

Alaska↗

USGS2026

Depositional environment and diagenetic history of gas hydrate-bearing sediments of the Alaska North Slope (HYDRATE 02 Geo Data Well)

We characterized the lithological, solid-phase geochemical, and rock magnetic properties of sediment cores from subpermafrost strata on the Alaska North Slope collected as part of the U.S. Department of Energy (DOE), the Japan Organization for Metals and Energy Security (JOGMEC), and the U.S. Geological Survey (USGS) Collaborative Gas Hydrate Research and Development (R&D) Project in Alaska. Pressure cores were recovered from the HYDRATE 02 Geo Data Well (GDW) at the Kuparuk State 7-11-12 site through two hydrate-bearing sand reservoirs, the B1 and D1 sands, and their finer-grained bounding sediments. Both the B1 and D1 sands are quartz-rich, chert-bearing, very fine litharenite sands. These submature to immature sands are poorly to moderately sorted and angular with local fine-scale cross-stratification. The B1 sand has larger grains and a lower clay content as compared to the D1 sand. These sands are the upper portions of upward coarsening progradational sequences. The clay- and silt-rich bounding muds exhibit fine-scale wavy and lenticular laminations, suggesting episodic high energy deposition events. Overall, these sediments were deposited in a shoreface to nearshore marine environment during the Paleogene, modulated by changing depositional energy associated with sea level variation. Organic matter δ 13 C and C/N composition of these sediments indicate a source mixture of land plants and freshwater plankton, with possible minor presence of oil within the B1 sand. These sediments contain high and variable total sulfur (TS) content, suggesting porewater conditions influenced by variable salinity over time. Rock magnetic analyses indicate precipitation of greigite in the mud beneath the D1 sand, in the basal C shale overlying the B1 sand, and the mud beneath the B1 sand, likely due to intervals of sulfate limitation during periods of lower Arctic Ocean salinity. Based on pyrite abundance, TS, and δ 34 S-TS composition, the D1 sand and bounding sediments experienced more substantial sulfide precipitation. The unit E basal shale overlying the D1 sand contains a 0.25 m thick pyrite-dominant sand, indicating local bottom water anoxic conditions. X-ray fluorescence scanning and discrete measurements provide additional supporting interpretation of the depositional and diagenetic processes that have occurred at this site and track the relative amount of drilling fluid contamination with barium abundance in the core samples.

Alaska↗

USGS2026

Permeability and compressibility of “seal” sediment overlying the B1 sand gas hydrate reservoir: Hydrate 02 Geo Data Well, Prudhoe Bay unit, Alaska North Slope

An important element in evaluating the viability of extracting methane from a gas hydrate-bearing reservoir is establishing the effectiveness of the overlying bounding sediment as a seal to prevent gas loss, to enable effective depressurization, and to prevent fluid from entering the reservoir during production. This laboratory study presents results for index properties (e.g., grain density, grain size, and liquid limit), compressibility and swelling indices, and permeability measurements on sediment overlying the gas hydrate-bearing reservoir that was the target of the recent JOGMEC-DOE-USGS collaborative gas hydrate production testing project on the Alaska North Slope (ANS). Sediment analyzed in this study was collected during pressure coring operations in the HYDRATE 02 Geo Data Well (GDW). The ∼6.1 m sediment interval recovered in Cores 13P and 14P (878.74–884.88 m measured depth, MD) exhibited heterogeneous sedimentologic characteristics at the centimeter scale, with sediments ranging from clay to thin silty-sand lithologies. Permeability measurements and index-property correlations indicate the interval’s overall in situ vertical permeability ranges from 0.2 to 3.6 microdarcy (μD). Results for compressibility ( C C = 0.255 ± 0.02) and swelling index ( C S = 0.04 ± 0.01) are consistent with estimates based on mineralogy and liquid limit correlations. Based on the measured compressibility, the ∼3 MPa increase in effective stress during the stable phase of depressurization-induced production is anticipated to have imposed 2.43 cm of compaction per meter in the reservoir overburden, reducing permeability by ∼36%. The overburden sediment’s low in situ permeability (3 to 4 orders of magnitude below permeabilities measured in the gas hydrate-bearing part of the B1 sand (unit B)) suggests the B1 sand′s overburden provides an effective seal. Such a seal promotes efficient production by limiting fluid flow into the reservoir during depressurization-induced gas hydrate dissociation.

Alaska↗

USGS2026

Strength, stiffness, and Poisson’s ratio measurements for cements used in the well completions for the extended-duration gas production test on the Alaskan North Slope

As part of an extended-duration production test from a natural gas hydrate reservoir on the Alaska North Slope, a suite of optical-fiber sensors was encased in the completion cement to provide stable downhole monitoring around each of the four project wells. How the sensors respond to changes in the reservoir over time depends in part on properties of the LiteCRETE, ArcticCem, or Tuned Light cement in which each sensor is encased, and on how well the cement bonded to the well casing, sensors, and sediment formation. Here, we report on physical properties of the cements (compressive and tensile strength, stiffness, and Poisson’s ratio), on the downhole distribution of the cements used in each well, and on the cement bond quality. Physical property measurements are presented for cements sampled during the completion activities for the three wells completed in 2022–2023. Samples were cured while being submerged in water at 2–4 °C, then tested at intervals from ∼30 days to more than one year. After an initial period of rapid increase, cement strengths largely stabilized around 120 days in all cases, meaning that cements in all wells reached their nominal strength plateau four months or more before the production test began. Calculations based on recorded volumes of pumped cement show the subpermafrost, main hole portion of each well is encased only in the higher-density “tail” cement used in that well. Downhole cement evaluation logs from two wells demonstrate how the presence of sensors and other hardware outside the casing interferes with the cement evaluation assessment. Nonetheless, the cement evaluations indicate a generally good bond with the formation and sensors over the gas hydrate reservoir intervals.

Alaska↗

USGS2026

Lithological control of gas hydrate saturation determined by pressure core analysis in sub-permafrost reservoirs of the Alaska North Slope (HYDRATE 02 Geo Data Well)

Quantitatively degassing pressure cores by controlled depressurization is a key approach to characterizing gas hydrate reservoirs by measuring the gas hydrate saturation (S h ) of sediments. We measured S h for 53 core sections from the Alaska North Slope during the JOGMEC-DOE-USGS Collaborative Gas Hydrate R&D Project in Alaska, from subpermafrost sediments that were later subjected to an extended-duration gas production test. We characterized lithologic influences on S h using physical property core scans (P-wave velocity, gamma ray attenuation density, and X-ray computed tomography) and grain size measurements. Pressure cores were recovered from the Hydrate-02 Geo Data Well (GDW) at the Kuparuk State 7-11-12 site through two hydrate-bearing sand reservoirs, the B1 and D1 sands, and their finer-grained bounding sediments. S h reaches very high values (68 to 91% of the pore space) in silty fine sands within the B1 sand, which also contains two lower P-wave velocity intervals (one measured at 30% S h ) within the main reservoir. S h and grain sizes of the B1 sand are generally higher than the D1 sand, which hosts high S h (53 to 73%) within its sandy silt to silty fine sands. The heterogeneous silty clay to silt “seal” sediments directly overlying both reservoirs have low S h (0 to 13%) even in thin, coarser beds, suggesting minimal methane transport between the reservoir and seal. S h decreases with depth downward toward the base of both the D1 and B1 sands, corresponding to decreasing grain size. These transitions are underlain by silty clay to clayey silt sediments with low S h (<10%), similar to the seal sediments. Slow depressurization was used to estimate a brackish salinity based on the pressure and temperature of the onset of hydrate dissociation for two core sections within the B1 sand. We show that S h increases with median grain size, sand content, and porosity but exhibits some variation within the sand beds that is not directly explained by lithology.

Alaska↗

USGS2026

Oil in the Alaska North Slope gas hydrate reservoir: Micro-CT and flow simulation insights into permeability

Gas hydrate-bearing sands on the Alaska North Slope (ANS) host minor volumes of crude oil whose impact on formation permeability has never been quantified relative to a gas hydrate reservoir system. Here, we combine in situ pressure-core microcomputed-tomography (μ-CT), thermogravimetric analysis (TGA), gas-chromatography–mass-spectrometry (GC–MS), scanning-electron microscopy coupled with energy-dispersive spectroscopy (SEM-EDS), and Stokes-flow simulation to (i) quantify oil saturation, (ii) infer its source, and (iii) evaluate its influence on permeability after gas-hydrate dissociation. μ-CT and SEM-EDS imaging identify the host sediment as silty, with some grain-coating clay present. Eight representative 300 3 -voxel subvolumes extracted from a preserved pressure core (Core 15P-3c, from the B1 sand (unit B), HYDRATE 02 Geo Data Well (GDW), 886.96–887.29 m measured depth, MD) exhibit porosities of 0.34–0.37 and an average oil saturation of 0.09 ± 0.03, in comparison to an independent TGA-based estimate of 0.16. GC-MS fingerprints obtained from an adjacent depressurized core (Core 17P-1, 891.37–891.44 m MD), together with oil pore habit revealed by μ-CT, suggest that the oil is partly native but also includes contributions from mineral oil-based drilling fluid contamination. Further analysis of oil–porewater interactions and flushing tests confirms that native oil saturation in the analyzed samples ranges from 0.04 to 0.08 with an average of approximately 0.06, and the oil is highly immobile. Flow simulations demonstrate that the native oil saturation of ≈0.06 reduces permeability by approximately 50% due to both pore blockage and increased flow-path tortuosity. These findings reveal the potential presence of native oil within the ANS gas hydrate reservoir and suggest that future simulation models may need to account for its impact on permeability to improve long-term performance predictions of gas and water production.

Alaska↗

USGS2025

International gas hydrate research and development

Gas hydrates are increasingly acknowledged as a potential future natural gas resource, sparking extensive global research into their geological characteristics and the technology needed for production. This paper offers a comprehensive review of gas hydrate-related research initiatives and production testing activities, including those in the Alaska North Slope (USA), Mackenzie Delta (Canada), Gulf of America (USA), South China Sea (PRC), Nankai Trough (Japan), Bay of Bengal (India), and Black Sea (Turkey). Recent studies have demonstrated successful gas production from hydrates found in sand-rich sediments using existing conventional technologies, particularly depressurization techniques. This review highlights the production trials conducted in Alaska, Canada, China, and Japan, providing insight into gas hydrate production feasibility. In addition, the implications of the completed production trials are reviewed relative to their energy planning considerations. This review also emphasizes research opportunities for technological advancements to effectively utilize the substantial volumes of gas stored in gas hydrates across various global geological settings. This compilation underscores the critical role that gas hydrates could play in meeting future energy demands.

Conference Paper↗

USGS2025

Proceedings of the Deepwater Hydrate Coring Expedition UT-GOM2-2

This report was the result of a scientific collaboration between the following institutions The University of Texas at Austin (UT), DOE, NETL, the United States Geological Survey (USGS), the Bureau of Ocean Energy Management (BOEM), The Ohio State University, Columbia University, University of New Hampshire, Oregon State University, University of Washington, Tufts University, Colorado School of Mines, and Geotek Ltd. In the summer and fall of 2023, the University of Texas (UT) Deepwater Hydrate Coring Expedition (UT-GOM2-2) drilled, cored, made downhole measurements, and analyzed samples from the seafloor to the base of the gas hydrate stability zone at Site H in the Walker Ridge Protracted Area Block 313 (Site H, WR313) in the Terrebonne basin, deepwater Gulf of America (Gulf of Mexico), herein the Gulf. This report is made up of a series of files as listed below that represents the “expedition report” of the 2023 UT-GOM2-2 Expedition.

Report↗

USGS2024

Long-term distributed temperature sensing monitoring for near-wellbore gas migration and gas hydrate formation

Well integrity monitoring has always been a critical component of subsurface oil and gas operations. Distributed fiber-optic sensing is an emerging technology that shows great promise for monitoring processes, both in boreholes and in other settings. In this study, we present a case study of using distributed temperature sensing (DTS) technology to monitor a cemented and plugged well in the Alaska North Slope (ANS). The well was drilled as part of a long-term gas hydrate study, and the downhole DTS data were recorded over a period of approximately 2 years. By applying a temporal gradient and removing instrument instability noise, we reveal subtle (<0.001°C/h) thermal anomalies, which are characterized by brief warming periods followed by longer cooling periods at discrete depths along the borehole. The observed coherent events show an upward trajectory from deeper formations into the overlying permafrost interval, with the thermal anomalies concentrated in relatively coarse-grained sandstone layers. We also observe that the upward migration rate of the DTS anomalies varies with formation lithology and that there is a spatial and temporal correlation between the subsurface events and measured wellhead annular pressures. We interpret that the observed warming events represent the exothermic process of gas hydrate formation that is occurring in association with the upward migration of gas outside the well casing, and this interpretation is confirmed by numerical simulations. These observations demonstrate the ability of suitably processed DTS data to detect subtle processes and highlight the value of DTS technologies for wellbore integrity monitoring.

Alaska↗

USGS2024

3-D geological modeling for numerical flow simulation studies of gas hydrate reservoirs at the Kuparuk State 7-11-12 Pad in the Prudhoe Bay Unit on the Alaska North Slope

Accurate reservoir evaluation requires reliable three-dimensional (3-D) geological models. This study conducted 3-D geological modeling for numerical flow simulation of the B1 sand gas hydrate reservoir at the Kuparuk State 7-11-12 pad, Prudhoe Bay Unit, Alaska North Slope. The model integrates well logs, core, and seismic data to address spatial heterogeneity in geological structures and reservoir properties. Two modeling types were performed: structural framework modeling and petrophysical property modeling. For structural framework modeling, seismic data and well log markers were used to reproduce subsurface structures characterized by a normal fault system. A volume-based modeling algorithm and stair-step gridding were applied. The resulting 3-D model comprised 2,640,000 grid cells across 264 layers, including seven fault grids. For petrophysical property modeling, total porosity was initially modeled using sequential Gaussian simulation with collocated cokriging. To reproduce the upward coarsening of the B1 sand, upscaled log-derived total porosity and a 3-D trend depicting total porosity variation were used as primary and secondary data, respectively. Gas hydrate saturation distribution was modeled similarly, with secondary data from estimated porosity distribution and seismic-derived acoustic impedance map enhancing accuracy. Results indicate higher gas hydrate saturation in the upper part of the B1 sand and areas with higher acoustic impedance. Intrinsic permeability was modeled from the total porosity and clay-bound water volume, and effective permeability was derived from the gas hydrate saturation and intrinsic permeability distributions based on the “Tokyo model”. Effective permeability distributions were influenced by the total porosity, gas hydrate saturation, and intrinsic permeability. Within the same layer, higher gas hydrate saturation leads to decreased effective permeability. In total, 100 sets of multiple scenarios were prepared, providing input data for dynamic flow simulations to evaluate the effects of lateral heterogeneity in reservoir properties and the hydraulic characteristics of faults on production behavior for preassessment before the long-term production test.

Alaska↗

USGS2024

Source, migration pathways, and atmospheric release of geologic methane associated with the complex permafrost regimes of the outer Mackenzie River Delta, Arctic, Canada

Sources and fluxes of methane to the atmosphere from permafrost are significant but poorly constrained in global climate models. We present data collected from the variable permafrost setting of the outer Mackenzie River Delta, including observations of aquatic methane seepage, core determinations of in situ methane occurrence and seep gas isotope geochemistry. The sources and locations of in situ geologic methane occurrence and aquatic and atmospheric gas release appear to be controlled by the regional geology and permafrost conditions. Where permafrost is >250 m thick, thermogenic gas deposits at depth are isolated by laterally continuous, low permeability ice-bearing sediments with few through-going thawed taliks. Thus, the observed in situ methane and aquatic gas seepage appears to be dominated by microbial methane. In contrast, where permafrost is <80 m thick, taliks are more likely to be through-going, providing permeable conduits from depth and migration pathways for both thermogenic and biogenic gas. Continuous annual fluid sampling of two lakes and a river channel documents aquatic methane flux from microbial sources, more deeply buried thermogenic sources, and mixtures of both. Using estimates of in situ methane concentration from deep core samples and observations of in situ free gas occurrences, we conclude that the reservoir of in situ geologic methane within ice bonded permafrost is substantial and that this methane is presently migrating with ongoing atmospheric release. It is our assessment that the permafrost setting, and processes described are sensitive to future climate change as the permafrost warms.

Mackenzie River Delta↗

USGS2024

Characterization of the structural–stratigraphic and reservoir controls on the occurrence of gas hydrates in the Eileen Gas Hydrate Trend, Alaska North Slope

One of the most studied permafrost-associated gas hydrate accumulations in Arctic Alaska is the Eileen Gas Hydrate Trend. This study provides a detailed re-examination of the Eileen Gas Hydrate Trend with a focus on the gas hydrate accumulation in the western part of the Prudhoe Bay Unit. This integrated analysis of downhole well log data and published geophysical data has provided new insight on structural, stratigraphic, and reservoir controls on the occurrence of gas hydrates in the Eileen Gas Hydrate Trend. This study revealed the relatively complex nature of the gas hydrate occurrences in the Eileen Gas Hydrate Trend, with gas hydrates present in a series of coarsening upward, laterally pervasive, mostly fine-grained sand beds exhibiting high gas hydrate saturations. Most of the gas hydrate-bearing reservoirs in the Eileen Gas Hydrate Trend are laterally segmented into distinct northwest- to southeast-trending fault blocks, occur in a combination of structural–stratigraphic traps, and are only partially hydrate filled with distinct down-dip water contacts. These findings suggest that the traditional parts of a petroleum system (i.e., reservoir, gas source, gas migration, and geologic timing of the system formation) also control the occurrence of gas hydrates in the Eileen Gas Hydrate Trend.

Alaska↗

USGS2024

Terrebonne Basin northern Gulf of Mexico, 30 July-28 September 2023

In the summer and fall of 2023, the Gulf of Mexico Deepwater Hydrate Coring Expedition (UT-GOM2-2) drilled, cored, made downhole measurements, and analyzed samples from the seafloor to the base of the gas hydrate stability zone in one location (Site H, WR313) in the Terrebonne basin, deepwater Gulf of Mexico. Analyses of data and samples from the expedition will inform biological, geochemical, and geomechanical models to constrain the role of gas hydrates in the carbon cycle and the potential for gas hydrates as an energy resource. Pressure and conventional cores were collected continuously to a depth of 155.1 meters below the seafloor (mbsf). At deeper depths, cores were taken periodically from hydrate-bearing sands and their bounding muds to a total depth of 861.3 mbsf. 162.6 m of conventional core and 54.8 m of pressure core were obtained. Twelve temperature measurements were made between 27.1 and 144.5 mbsf to determine the geothermal gradient. At the seafloor, more than 4 m of sandy silt of unknown origin was encountered. Beneath this sand, to a depth of ~200 mbsf, the section was composed of interbedded mud and biogenic carbonate ooze. The biogenic ooze correlated to low density and high porosity intervals observed in the previously acquired logging while drilling (LWD) data and as measured. Calcareous nannofossil biostratigraphy constrains the entire record to the Pleistocene (< 0.91 million years) with a pronounced increase in sedimentation rate with depth. Beneath 200 mbsf, the section was predominantly composed of mud with two thicker, hydrate-bearing coarse-grained intervals, which are commonly known as the Blue and Orange sands. The dissolved gas concentration was quantified from pressure cores. In the shallow section, dissolved methane concentration increased below the sulfate-methane transition zone (SMTZ) and reaches saturation (the limit of solubility for methane) at 147 mbsf. Gas expansion was very common in conventional and depressurized pressure (conventionalized) cores below the SMTZ. At deeper depths, the methane concentration within muds bounding the Blue and Orange reservoirs was generally found to be less than saturation. The dissolved and hydrate gas composition is consistent with a microbial source, containing greater than 99.99% methane and only trace concentrations of ethane, propane, and butane. The methane to ethane ratio (C 1 /C 2 ) and the methane to ethane plus propane (C 1 /(C 2 +C 3 )) decrease with depth down to at least 678 mbsf, mainly driven by the increase in ethane with depth. It is unclear if this trend continues through the Orange sand interval. The δ 13 C isotopic signature of methane ranges between -69.9 and -78.5 ‰ Vienna Pee Dee Belemnite (VPDB). Pressure core recovery of all sandy intervals was poor. However, pressure core logs of the Orange sand show intervals of low density and high velocity, which are indicative of high hydrate saturation. One core from within the Orange sand was composed of interbedded graded sandy silt and mud. The sandy silts from this core are composed of mainly quartz and feldspar with some lithics. Most of the recovered pressure core samples are maintained at near in-situ pressure and temperature (within the hydrate stability field) at the University of Texas Pressure Core Center awaiting analysis. In the shallow section, samples will be used to determine the flux of organic carbon through the basin system, find the rate at which that carbon was consumed, and understand the microbial population responsible for these processes. In the deeper section, samples from in and around the hydrate reservoirs will be used to determine the petrophysical properties of the reservoir and bounding seals in these systems.

Gulf of Mexico, Terrebonne Basin↗

USGS2023

Machine learning application to assess occurrence and saturations of methane hydrate in marine deposits offshore India

Artificial Neural Networks (ANN) were used to assess methane hydrate occurrence and saturation in marine sediments offshore India. The ANN analysis classifies the gas hydrate occurrence into three types: methane hydrate in pore space, methane hydrate in fractures, or no methane hydrate. Further, predicted saturation characterizes the volume of gas hydrate with respect to the available void volume. Log data collected at six wells, which were drilled during the India National Gas Hydrate Program Expedition 02 (NGHP-02), provided a combination of well log measurements that were used as input for machine learning (ML) models. Well log measurements included density, porosity, electrical resistivity, natural gamma radiation, and acoustic wave velocity. Combinations of well logs used in the ML models provide good overall balanced accuracy (0.79 to 0.86) for the prediction of the gas hydrate occurrence and good accuracy (0.68 to 0.92) for methane hydrate saturation prediction in the marine accumulations against reference data. The accuracy scores indicate that the ML models can successfully predict reservoir characteristics for marine methane hydrate deposits. The results indicate that the ML models can either augment physics-driven methods for assessing the occurrence and saturation of methane hydrate deposits or serve as an independent predictive tool for those characteristics.

Journal Interpretation↗

USGS2023

Characterization of a complex sand-rich gas hydrate reservoir system in the Indian marine continental margin with downhole log and seismic data

Logging-while-drilling (LWD) and coring data were acquired in Areas A, B, C and E during the National Gas Hydrate Program Expedition 02 (NGHP-02). At Sites NGHP-02-16, −17, −20, −23 and −24 of Area B in the Indian Krishna-Godavari Basin, the gas hydrate-bearing sand-rich reservoirs directly in contact with an underlying water-saturated sediment were revealed near the seismic-inferred bottom simulating reflector (BSR) along a large anticlinal structure. Lithofacies analysis of cores show that the lower gas hydrate-bearing reservoir section at these sites is an interbedded unit with thin fine-sand layers alternating with clay-rich layers. We reanalyzed the LWD data including resistivity, compressional-wave and shear-wave acoustic velocities to assess and compare the spatial variation of sand-hosted gas hydrate and possible related free-gas accumulations. The presence of free gas-bearing sediments in direct contact with gas hydrate-bearing sediments was confirmed at Sites NGHP-02-20 and −24 along the northeastern flank of the anticline. The sand-rich reservoirs associated with the Area B anticlinal feature reveal different pore-filling constituents and variable boundary conditions, including gas hydrate/water contacts and gas hydrate/free gas contacts. We infer that the sedimentary depositional history at Sites NGHP-02-20 and −24, may have resulted in an upward shift of the base of gas hydrate stability zone, that could have led to in situ gas hydrate dissociation and the accumulation of free gas and coexistence interval below the log-inferred gas hydrate-bearing reservoir sections. This study demonstrates that reservoir heterogeneity and fluid migration were major factors affecting the distribution of gas hydrate and free gas in the identified sand-rich reservoirs.

Journal of Marine and Petroleum Geology↗

USGS2022

Geological reservoir characterization of a gas hydrate prospect associated with the Hydrate-01 Stratigraphic Test Well, Alaska North Slope

Geological reservoir characterization is essential for accurate evaluation of gas production performance from gas hydrate reservoirs. Particularly, the understanding of reservoir architecture and heterogeneity is of great importance since these are considered as major controls on fluid hydrodynamic and thermodynamic conditions. This study deals with well log and three-dimensional (3-D) vertical seismic profile (VSP) data acquired from the Hydrate-01 Stratigraphic Test Well within the 7-11-12 prospect, Prudhoe Bay Unit, Alaska North Slope and reports on the results of geological/geophysical evaluation related to the geological structure and reservoir properties of the 7-11-12 prospect. The structural trends of the target reservoirs, based on well correlations, are mostly consistent with the predrill prediction using the surface seismic data, and infer the existence of subseismic faults cutting through the Hydrate-01 well. The 3-D VSP data confirm a down-to-the-east normal fault that offsets the reservoir units across the Hydrate-01 well, which is concordant with the well identification of the same fault, and indicate a northeast-dipping relay structure associated with the overstepping normal faults. The edge enhancement attribute associated with discontinuity generated from the 3-D VSP data shows small faults/fractures, possibly as part of a complex fault network within the imaged normal fault system. These results reveal that the 3-D VSP data provide detailed structural information that is not present from the surface seismic data. The Hydrate-01 well log data confirm the occurrence of gas hydrate at high saturation in the two targeted sand units (B1 and D1 sands), and the comparison to a nearby pre-existing well (7-11-12 well) shows the same general trend in gas hydrate saturation as a map of seismic impedance generated from surface seismic data. The well log data also suggest that the base of gas hydrate occurrence in the Hydrate-01 and 7-11-12 wells is almost aligned at the same depth in both of the targeted B1 and D1 sand reservoirs. Especially for the D1 sand in the Hydrate-01 well, the resistivity logs show a sharp transition from high gas hydrate saturation to fully water-saturated within the D1 sand, suggesting a common gas hydrate/water contact. The results of this study will be used to construct the geological models needed for reservoir simulation studies and they can provide important insights into the geological factors that control the occurrence of gas hydrate on the Alaska North Slope.

Alaska↗

USGS2022

Virtual special issue of recent advances on gas hydrates scientific drilling in Alaska

Gas hydrate refers to a non-stoichiometric clathrate that forms spontaneously in the natural environment whenever sufficient quantities of gases of appropriate size (most commonly methane) interact with abundant water under specific conditions of temperature and pressure. (1,2) Such conditions occur wherever the shallow geothermal gradient has been suppressed by either deepwater or thick permafrost, allowing for relatively low temperatures to coexist with elevated pressures. The volume of gas hydrate on Earth is difficult to constrain, (3) but it is sufficient that gas hydrate is a meaningful potential component of (1) the long-term natural cycling of carbon, (2) the nearer term environmental changes in response to warming climates, (4) and (3) future energy supply systems. Since the initial recognition of gas hydrate as an abundant component in nature in the late 1960s, a series of scientific drilling expeditions conducted by both the Integrated Ocean Discovery Program (and successors) and national research and development programs in Canada, Japan, China, the United States, South Korea, and others (5) have explored the occurrence and nature of gas hydrates. In particular, the desire for expanded energy supply options to support the economic development and energy security for nations around the globe is currently motivating a broad range of laboratory and numerical simulation studies in support of an ongoing series of field-based scientific tests of the potential commercial viability of gas extraction from natural gas hydrate deposits. (6)

Journal of Energy & Fuels↗

USGS2022

Review of past gas Production attempts from subsurface gas hydrate deposits and necessity of long-term production testing

This paper summarizes the conditions, applied techniques, results, and lessons of major field gas production attempts from gas hydrates in the past and the necessity of longer term production testing with the scale of years to fulfill the gap between the currently available information and the knowledge required for commercial development. The temporal and spatial scales of field production test projects employing depressurization have expanded since 2002. The results from the projects have proved the applicability of these techniques in both onshore and offshore conditions. However, many technical and reservoir condition-related issues have emerged in gas production, and the gap between current status and industrial requirements is still large. Sand control, artificial lift, and related flow assurance issues are common technical issues that impact onshore and offshore production testing operations. Different reservoir responses were observed well by well, and discrepancy between model predictions and actual field measurements were seen, although reasonable matches were made for short-term behaviors. Those observations suggest that temporal change of the wellbore and near-wellbore conditions and reservoir heterogeneity that cannot be fully modeled have caused complex short-term responses to the depressurization operations. To ensure the long-term operational stability and reliability of the prediction technologies for production behaviors that are essential for commercialization of gas hydrate resources, gas hydrate production testing with comparable duration with commercial operations are necessary. Due to the locality of geological conditions in gas hydrate reservoirs, numerous gas production tests will be required to understand the factors controlling gas production.

Journal of Energy and Fuels↗