Search USGS⌕ Search

Geology topics

Stephen C. Harmsen

Publications and source records attributed to Stephen C. Harmsen.

15 recordsLinked to original sources
USGS2015

Seismic-hazard maps for the conterminous United States, 2014

The maps presented here provide an update to the 2008 data contained in U.S Geological Survey Scientific Investigations Map 3195 ( http://pubs.usgs.gov/sim/3195/ ).Probabilistic seismic-hazard maps were prepared for the conterminous United States for 2014 portraying peak horizontal acceleration and horizontal spectral response acceleration for 0.2- and 1.0-second periods with probabilities of exceedance of 10 percent in 50 years and 2 percent in 50 years. All of the maps were prepared by combining the hazard derived from spatially smoothed historical seismicity with the hazard from fault-specific sources. The acceleration values contoured are the random horizontal component. The reference site condition is firm rock, defined as having an average shear-wave velocity of 760 m/s in the top 30 meters corresponding to the boundary between NEHRP (National Earthquake Hazards Reduction program) site classes B and C. This data set represents the results of calculations of hazard curves for a grid of points with a spacing of 0.05 degrees in latitude and longitude. The grid of points was contoured to produce the final representation of the seismic hazard. These maps are intended to summarize the available quantitative information about seismic ground motion hazard for the conterminous United States from geologic and geophysical sources.

Scientific Investigations Map↗
USGS2014

Implementation of NGA-West2 ground motion models in the 2014 U.S. National Seismic Hazard Maps

The U.S. National Seismic Hazard Maps (NSHMs) have been an important component of seismic design regulations in the United States for the past several decades. These maps present earthquake ground shaking intensities at specified probabilities of being exceeded over a 50-year time period. The previous version of the NSHMs was developed in 2008; during 2012 and 2013, scientists at the U.S. Geological Survey have been updating the maps based on their assessment of the “best available science,” resulting in the 2014 NSHMs. The update includes modifications to the seismic source models and the ground motion models (GMMs) for sites across the conterminous United States. This paper focuses on updates in the Western United States (WUS) due to the use of new GMMs for shallow crustal earthquakes in active tectonic regions developed by the Next Generation Attenuation (NGA-West2) project. Individual GMMs, their weighted combination, and their impact on the hazard maps relative to 2008 are discussed. In general, the combined effects of lower medians and increased standard deviations in the new GMMs have caused only small changes, within 5–20%, in the probabilistic ground motions for most sites across the WUS compared to the 2008 NSHMs.

Earthquake Spectra↗
USGS2014

Documentation for the 2014 update of the United States national seismic hazard maps

The national seismic hazard maps for the conterminous United States have been updated to account for new methods, models, and data that have been obtained since the 2008 maps were released (Petersen and others, 2008). The input models are improved from those implemented in 2008 by using new ground motion models that have incorporated about twice as many earthquake strong ground shaking data and by incorporating many additional scientific studies that indicate broader ranges of earthquake source and ground motion models. These time-independent maps are shown for 2-percent and 10-percent probability of exceedance in 50 years for peak horizontal ground acceleration as well as 5-hertz and 1-hertz spectral accelerations with 5-percent damping on a uniform firm rock site condition (760 meters per second shear wave velocity in the upper 30 m, V S30 ). In this report, the 2014 updated maps are compared with the 2008 version of the maps and indicate changes of plus or minus 20 percent over wide areas, with larger changes locally, caused by the modifications to the seismic source and ground motion inputs.

Open-File Report↗
USGS2014

2014 update of the U.S. national seismic hazard maps

We held 8 regional and topical workshops across the U.S. to gather information for these maps. The maps were available to the public for comment during a 60-day period. A Steering Committee (9 experts) was assembled to review the inputs and results and provide additional insights. The maps have been presented at several professional meetings. In this talk we discuss: (1) CEUS, (2) WUS (outside California), (3) California, (4) Ground motion models We discuss the hazard maps and hazard curves used in the building code. The maps in this presentation are for 2% probability of exceedance in 50 years on a uniform firm rock site condition (V S30 =760 m/s). Maps are for 0.2 s (5 Hz) spectral acceleration with 5% damping. We consider difference maps (2014-2008) and ratio maps (2014/2008).

Book↗
USGS2013

Conditional spectrum computation incorporating multiple causal earthquakes and ground-motion prediction models

The conditional spectrum (CS) is a target spectrum (with conditional mean and conditional standard deviation) that links seismic hazard information with ground-motion selection for nonlinear dynamic analysis. Probabilistic seismic hazard analysis (PSHA) estimates the ground-motion hazard by incorporating the aleatory uncertainties in all earthquake scenarios and resulting ground motions, as well as the epistemic uncertainties in ground-motion prediction models (GMPMs) and seismic source models. Typical CS calculations to date are produced for a single earthquake scenario using a single GMPM, but more precise use requires consideration of at least multiple causal earthquakes and multiple GMPMs that are often considered in a PSHA computation. This paper presents the mathematics underlying these more precise CS calculations. Despite requiring more effort to compute than approximate calculations using a single causal earthquake and GMPM, the proposed approach produces an exact output that has a theoretical basis. To demonstrate the results of this approach and compare the exact and approximate calculations, several example calculations are performed for real sites in the western United States. The results also provide some insights regarding the circumstances under which approximate results are likely to closely match more exact results. To facilitate these more precise calculations for real applications, the exact CS calculations can now be performed for real sites in the United States using new deaggregation features in the U.S. Geological Survey hazard mapping tools. Details regarding this implementation are discussed in this paper.

Bulletin of the Seismological Society of America↗
USGS2012

Seismic hazard of American Samoa and neighboring South Pacific Islands--methods, data, parameters, and results

American Samoa and the neighboring islands of the South Pacific lie near active tectonic-plate boundaries that host many large earthquakes which can result in strong earthquake shaking and tsunamis. To mitigate earthquake risks from future ground shaking, the Federal Emergency Management Agency requested that the U.S. Geological Survey prepare seismic hazard maps that can be applied in building-design criteria. This Open-File Report describes the data, methods, and parameters used to calculate the seismic shaking hazard as well as the output hazard maps, curves, and deaggregation (disaggregation) information needed for building design. Spectral acceleration hazard for 1 Hertz having a 2-percent probability of exceedance on a firm rock site condition (Vs30=760 meters per second) is 0.12 acceleration of gravity (1 second, 1 Hertz) and 0.32 acceleration of gravity (0.2 seconds, 5 Hertz) on American Samoa, 0.72 acceleration of gravity (1 Hertz) and 2.54 acceleration of gravity (5 Hertz) on Tonga, 0.15 acceleration of gravity (1 Hertz) and 0.55 acceleration of gravity (5 Hertz) on Fiji, and 0.89 acceleration of gravity (1 Hertz) and 2.77 acceleration of gravity (5 Hertz) on the Vanuatu Islands.

South Pacific Islands↗
USGS2011

Seismic-Hazard Maps for the Conterminous United States, 2008

Probabilistic seismic-hazard maps were prepared for the conterminous United States portraying peak horizontal acceleration and horizontal spectral response acceleration for 0.2- and 1.0-second periods with probabilities of exceedance of 10 percent in 50 years and 2 percent in 50 years. All of the maps were prepared by combining the hazard derived from spatially smoothed historic seismicity with the hazard from fault-specific sources. The acceleration values contoured are the random horizontal component. The reference site condition is firm rock, defined as having an average shear-wave velocity of 760 m/s in the top 30 meters corresponding to the boundary between NEHRP (National Earthquake Hazards Reduction program) site classes B and C. This data set represents the results of calculations of hazard curves for a grid of points with a spacing of 0.05 degrees in latitude and longitude. The grid of points were contoured to produce the final representation of the seismic-hazard. These maps are intended to summarize the available quantitative information about seismic ground motion hazard for the conterminous United States from geologic and geophysical source.

Scientific Investigations Map↗
USGS2008

Documentation for the 2008 update of the United States National Seismic Hazard Maps

The 2008 U.S. Geological Survey (USGS) National Seismic Hazard Maps display earthquake ground motions for various probability levels across the United States and are applied in seismic provisions of building codes, insurance rate structures, risk assessments, and other public policy. This update of the maps incorporates new findings on earthquake ground shaking, faults, seismicity, and geodesy. The resulting maps are derived from seismic hazard curves calculated on a grid of sites across the United States that describe the frequency of exceeding a set of ground motions. The USGS National Seismic Hazard Mapping Project developed these maps by incorporating information on potential earthquakes and associated ground shaking obtained from interaction in science and engineering workshops involving hundreds of participants, review by several science organizations and State surveys, and advice from two expert panels. The new probabilistic hazard maps represent an update of the 2002 seismic hazard maps developed by Frankel and others (2002), which used the methodology developed for the 1996 version of the maps (Frankel and others, 1996). Algermissen and Perkins (1976) published the first probabilistic seismic hazard map of the United States which was updated in Algermissen and others (1990). The National Seismic Hazard Maps represent our assessment of the “best available science” in earthquake hazards estimation for the United States (maps of Alaska and Hawaii as well as further information on hazard across the United States are available on our Web site at http://earthquake.usgs.gov/research/hazmaps/ ).

Open-File Report↗
USGS2008

Simulated ground motion in Santa Clara Valley, California, and vicinity from M≥6.7 scenario earthquakes

Models of the Santa Clara Valley (SCV) 3D velocity structure and 3D finite-difference software are used to predict ground motions from scenario earthquakes on the San Andreas (SAF), Monte Vista/Shannon, South Hayward, and Calaveras faults. Twenty different scenario ruptures are considered that explore different source models with alternative hypocenters, fault dimensions, and rupture velocities and three different velocity models. Ground motion from the full wave field up to 1 Hz is exhibited as maps of peak horizontal velocity and pseudospectral acceleration at periods of 1, 3, and 5 sec. Basin edge effects and amplification in sedimentary basins of the SCV are observed that exhibit effects from shallow sediments with relatively low shear-wave velocity (330 m/sec). Scenario earthquakes have been simulated for events with the following magnitudes: (1) M 6.8–7.4 Calaveras sources, (2) M 6.7–6.9 South Hayward sources, (3) M 6.7 Monte Vista/Shannon sources, and (4) M 7.1–7.2 Peninsula segment of the SAF sources. Ground motions are strongly influenced by source parameters such as rupture velocity, rise time, maximum depth of rupture, hypocenter, and source directivity. Cenozoic basins also exert a strong influence on ground motion. For example, the Evergreen Basin on the northeastern side of the SCV is especially responsive to 3–5-sec energy from most scenario earthquakes. The Cupertino Basin on the southwestern edge of the SCV tends to be highly excited by many Peninsula and Monte Vista fault scenarios. Sites over the interior of the Evergreen Basin can have long-duration coda that reflect the trapping of seismic energy within this basin. Plausible scenarios produce predominantly 5-sec wave trains with greater than 30 cm/sec sustained ground-motion amplitude with greater than 30 sec duration within the Evergreen Basin.

California↗
USGS2005

Seismic-hazard maps for the conterminous United States

This publication consists of six map sheets (titles and text included in this document, below), geospatial datasets, and metadata. The geospatial datasets consist of ArcInfo export files for the seismic-hazard point and polygon data shown on the sheets. Probabilistic seismic-hazard maps were prepared for the conterminous United States portraying peak horizontal acceleration and horizontal spectral response acceleration for 0.2- and 1.0-second periods with probabilities of exceedance of 10 percent in 50 years and 2 percent in 50 years. All of the maps were prepared by combining the hazard derived from spatially smoothed historic seismicity with the hazard from fault-specific sources. The acceleration values contoured are the random horizontal component. The reference site condition is firm rock, defined as having an average shear-wave velocity of 760 m/sec in the top 30 meters corresponding to the boundary between NEHRP (National Earthquake Hazards Reduction program) site classes B and C. This data set represents the results of calculations of hazard curves for a grid of points with a spacing of 0.05 degrees in latitude and longitude. The points were contoured to produce the final representation of the seismic hazard.

Scientific Investigations Map↗
USGS2001

Mean and modal ϵ in the deaggregation of probabilistic ground motion

An important element of probabilistic seismic-hazard analysis (PSHA) is the incorporation of ground-motion uncertainty from the earthquake sources. The standard normal variate ϵ measures the difference between any specified spectral-acceleration level, or SA 0 , and the estimated median spectral acceleration from each probabilistic source. In this article, mean and modal values of ϵ for a specified SA 0 are defined and computed from all sources considered in the USGS 1996 PSHA maps. Contour maps of ϵ are presented for the conterminous United States for 1-, 0.3-, and 0.2-sec SA 0 and for peak horizontal acceleration, PGA 0 corresponding to a 2% probability of exceedance (PE) in 50 yr, or mean annual rate of exceedance, r , of 0.000404. Mean and modal ϵ exhibit a wide variation geographically for any specified PE. Modal ϵ for the 2% in 50 yr PE exceeds 2 near the most active western California faults, is less than –1 near some less active faults of the western United States (principally in the Basin and Range), and may be less than 0 in areal fault zones of the central and eastern United States (CEUS). This geographic variation is useful for comparing probabilistic ground motions with ground motions from scenario earthquakes on dominating faults, often used in seismic-resistant provisions of building codes. An interactive seismic-hazard deaggregation menu item has been added to the USGS probabilistic seismic-hazard analysis Web site, http://geohazards.cr.usgs.gov/eq/ , allowing visitors to compute mean and modal distance, magnitude, and ϵ corresponding to ground motions having mean return times from 250 to 5000 yr for any site in the United States.

Bulletin of the Seismological Society of America↗
USGS1999

Seismic-hazard maps for Alaska and the Aleutian Islands

Probabilistic seismic hazard maps were prepared for Alaska portraying peak horizontal ground acceleration and horizontal spectral response acceleration for 0.2, 0.3, and 1.0 second periods with probabilities of exceedance of 10% in 50 years and 2% in 50 years. This particular data set is for horizontal spectral response acceleration for 1.0 second period with a 10% probability of exceedance in 50 years. All of the maps were prepared by combining hazard derived from spatially- smoothed historic seismicity with hazard from fault-specific sources. The acceleration values contoured are the random horizontal component. The reference site condition is firm rock, defined as having an average shear-wave velocity of 760 m/sec in the top 30 meters corresponding to the boundary between NEHRP site classes B and C. This data set represents the results of calculations of hazard curves for a grid of points with a spacing of 0.1 degrees in latitude and longitude. The grid of points were contoured to produce the final representation of the seismic-hazard.

IMAP↗
USGS1996

Site-response maps for the Los Angeles region based on earthquake ground motions

Ground-motion records from aftershocks of the 1994 Northridge earthquake and main-shock records from the 1971 San Fernando, 1987 Whittier Narrows, 1991 Sierra Madre, and 1994 Northridge earthquakes are used to estimate site response in the urban Los Angeles, California, area. Two frequency bands are considered, 0.5-1.5 Hz and 2.0-6.0 Hz. Instrument characteristics prevented going to lower frequencies, and frequencies above 6.0 Hz are less important to the building inventory. Site response determined at the instrumented locations is associated with the surficial geology and contoured to produce a continuous spatial estimation of site response. The maps in this report are preliminary and will evolve as more data become available and more analysis is done.

California↗