Search USGS⌕ Search

Geology topics

S.H. Cannon

Publications and source records attributed to S.H. Cannon.

At least 19 recordsLinked to original sources
USGS2012

Debris-flow susceptibility of watersheds recently burned by wildfire

Evaluation of the erosional response of 95 recently burned watersheds in Colorado, New Mexico, and southern California to storm rainfall established the factors that best differentiate between debris-flow producing basins and those that produced other flow responses. These factors are drainage-basin morphology and lithology, and the presence or absence of water-repellent soils. Basins underlain by sedimentary rocks were most likely to produce debris flows that contain large material, and sand- and gravel-dominated debris flows were generated primarily from terrain underlain by decomposed granite. Basin-area and relief thresholds define the morphologic conditions under which both types of debris flows occurred. Debris flows containing large material were more likely to be produced from basins without water-repellent soils than from basins with water repellency. The occurrence of sand and gravel-dominated debris flows depended on the presence of water repellent soils. Copyright 2004 ASCE.

Conference Paper↗
USGS2011

In situ measurements of post-fire debris flows in southern California: Comparisons of the timing and magnitude of 24 debris-flow events with rainfall and soil moisture conditions

Debris flows often occur in burned steeplands of southern California, sometimes causing property damage and loss of life. In an effort to better understand the hydrologic controls on post-fire debris-flow initiation, timing and magnitude, we measured the flow stage, rainfall, channel bed pore fluid pressure and hillslope soil-moisture accompanying 24 debris flows recorded in five different watersheds burned in the 2009 Station and Jesusita Fires (San Gabriel and Santa Ynez Mountains). The measurements show substantial differences in debris-flow dynamics between sites and between sequential events at the same site. Despite these differences, the timing and magnitude of all events were consistently associated with local peaks in short duration (< = 30 min) rainfall intensity. Overall, debris-flow stage was best cross-correlated with time series of 5-min rainfall intensity, and lagged the rainfall by an average of just 5 min. An index of debris-flow volume was also best correlated with short-duration rainfall intensity, but found to be poorly correlated with storm cumulative rainfall and hillslope soil water content. Post-event observations of erosion and slope stability modeling suggest that the debris flows initiated primarily by processes related to surface water runoff, rather than shallow landslides. By identifying the storm characteristics most closely associated with post-fire debris flows, these measurements provide valuable guidance for warning operations and important constraints for developing and testing models of post-fire debris flows. copyright. 2011 by the American Geophysical Union.

Journal of Geophysical Research F: Earth Surface↗
USGS2011

Rainfall intensity-duration thresholds for postfire debris-flow emergency-response planning

Following wildfires, emergency-response and public-safety agencies can be faced with evacuation and resource-deployment decisions well in advance of coming winter storms and during storms themselves. Information critical to these decisions is provided for recently burned areas in the San Gabriel Mountains of southern California. A compilation of information on the hydrologic response to winter storms from recently burned areas in southern California steeplands is used to develop a system for classifying magnitudes of hydrologic response. The four-class system describes combinations of reported volumes of individual debris flows, consequences of debris flows and floods in an urban setting, and spatial extents of the hydrologic response. The range of rainfall conditions associated with different magnitude classes is defined by integrating local rainfall data with the response magnitude information. Magnitude I events can be expected when within-storm rainfall accumulations (A) of given durations (D) fall above the threshold A = 0.4D0.5 and below A = 0.5D0.6 for durations greater than 1 h. Magnitude II events will be generated in response to rainfall accumulations and durations between A = 0.4D0.5 and A = 0.9D0.5 for durations less than 1 h, and between A = 0.5D0.6 and A = 0.9D0.5 or durations greater than 1 h. Magnitude III events can be expected in response to rainfall conditions above the threshold A = 0.9D0.5. Rainfall threshold-magnitude relations are linked with potential emergency-response actions as an emergency-response decision chart, which leads a user through steps to determine potential event magnitudes and identify possible evacuation and resource-deployment levels. Use of this information in planning and response decision-making process could result in increased safety for both the public and emergency responders. ?? 2011 US Government.

Natural Hazards↗
USGS2009

Predicting the probability and volume of postwildfire debris flows in the intermountain western United States

Empirical models to estimate the probability of occurrence and volume of postwildfire debris flows can be quickly implemented in a geographic information system (GIS) to generate debris-flow hazard maps either before or immediately following wildfires. Models that can be used to calculate the probability of debris-flow production from individual drainage basins in response to a given storm were developed using logistic regression analyses of a database from 388 basins located in 15 burned areas located throughout the U.S. Intermountain West. The models describe debris-flow probability as a function of readily obtained measures of areal burned extent, soil properties, basin morphology, and rainfall from short-duration and low-recurrence-interval convective rainstorms. A model for estimating the volume of material that may issue from a basin mouth in response to a given storm was developed using multiple linear regression analysis of a database from 56 basins burned by eight fires. This model describes debris-flow volume as a function of the basin gradient, aerial burned extent, and storm rainfall. Applications of a probability model and the volume model for hazard assessments are illustrated using information from the 2003 Hot Creek fire in central Idaho. The predictive strength of the approach in this setting is evaluated using information on the response of this fire to a localized thunderstorm in August 2003. The mapping approach presented here identifies those basins that are most prone to the largest debris-flow events and thus provides information necessary to prioritize areas for postfire erosion mitigation, warnings, and prefire management efforts throughout the Intermountain West.

Geological Society of America Bulletin↗
USGS2008

Joint NOAA/NWS/USGS prototype debris flow warning system for recently burned areas in Southern California

Debris flows, also known as mudslides, are composed gravity-driven mixtures of sediment and water that travel through steep channels, over open hillslopes, and the like. Addressing this issue, US Geological Survey (USGS) and NOAA have established a debris-flow warning system that has the ability to monitor and forecast precipitation and issue timely weather hazard warning. In 2005, this joint NOAA-USGS prototype debris-flow warning system was issued in Southern California and as a result, it has provided valuable information to emergency managers in affected communities.

California↗
USGS2008

A study of methods to estimate debris flow velocity

Debris flow velocities are commonly back-calculated from superelevation events which require subjective estimates of radii of curvature of bends in the debris flow channel or predicted using flow equations that require the selection of appropriate rheological models and material property inputs. This research investigated difficulties associated with the use of these conventional velocity estimation methods. Radii of curvature estimates were found to vary with the extent of the channel investigated and with the scale of the media used, and back-calculated velocities varied among different investigated locations along a channel. Distinct populations of Bingham properties were found to exist between those measured by laboratory tests and those back-calculated from field data; thus, laboratory-obtained values would not be representative of field-scale debris flow behavior. To avoid these difficulties with conventional methods, a new preliminary velocity estimation method is presented that statistically relates flow velocity to the channel slope and the flow depth. This method presents ranges of reasonable velocity predictions based on 30 previously measured velocities. ?? 2008 Springer-Verlag.

Landslides↗
USGS2008

Sources of debris flow material in burned areas

The vulnerability of recently burned areas to debris flows has been well established. Likewise, it has been shown that many, if not most, post-fire debris flows are initiated by runoff and erosion and grow in size through erosion and scour by the moving debris flow, as opposed to landslide-initiated flows with little growth. To better understand the development and character of these flows, a study has been completed encompassing 46 debris flows in California, Utah, and Colorado, in nine different recently burned areas. For each debris flow, progressive debris production was measured at intervals along the length of the channel, and from these measurements graphs were developed showing cumulative volume of debris as a function of channel length. All 46 debris flows showed significant bulking by scour and erosion, with average yield rates for each channel ranging from 0.3 to 9.9??m3 of debris produced for every meter of channel length, with an overall average value of 2.5??m3/m. Significant increases in yield rate partway down the channel were identified in 87% of the channels, with an average of a three-fold increase in yield rate. Yield rates for short reaches of channels (up to several hundred meters) ranged as high as 22.3??m3/m. Debris was contributed from side channels into the main channels for 54% of the flows, with an average of 23% of the total debris coming from those side channels. Rill erosion was identified for 30% of the flows, with rills contributing between 0.1 and 10.5% of the total debris, with an average of 3%. Debris was deposited as levees in 87% of the flows, with most of the deposition occurring in the lower part of the basin. A median value of 10% of the total debris flow was deposited as levees for these cases, with a range from near zero to nearly 100%. These results show that channel erosion and scour are the dominant sources of debris in burned areas, with yield rates increasing significantly partway down the channel. Side channels are much more important sources of debris than rills. Levees are very common, but the size and effect on the amount of debris that reaches a canyon mouth is highly variable. ?? 2007 Elsevier B.V. All rights reserved.

Geomorphology↗
USGS2008

Storm rainfall conditions for floods and debris flows from recently burned areas in southwestern Colorado and southern California

Debris flows generated during rain storms on recently burned areas have destroyed lives and property throughout the Western U.S. Field evidence indicate that unlike landslide-triggered debris flows, these events have no identifiable initiation source and can occur with little or no antecedent moisture. Using rain gage and response data from five fires in Colorado and southern California, we document the rainfall conditions that have triggered post-fire debris flows and develop empirical rainfall intensity-duration thresholds for the occurrence of debris flows and floods following wildfires in these settings. This information can provide guidance for warning systems and planning for emergency response in similar settings. Debris flows were produced from 25 recently burned basins in Colorado in response to 13 short-duration, high-intensity convective storms. Debris flows were triggered after as little as six to 10??min of storm rainfall. About 80% of the storms that generated debris flows lasted less than 3??h, with most of the rain falling in less than 1??h. The storms triggering debris flows ranged in average intensity between 1.0 and 32.0??mm/h, and had recurrence intervals of two years or less. Threshold rainfall conditions for floods and debris flows sufficiently large to pose threats to life and property from recently burned areas in south-central, and southwestern, Colorado are defined by: I = 6.5D-??0.7 and I = 9.5D-??0.7, respectively, where I = rainfall intensity (in mm/h) and D = duration (in hours). Debris flows were generated from 68 recently burned areas in southern California in response to long-duration frontal storms. The flows occurred after as little as two hours, and up to 16??h, of low-intensity (2-10??mm/h) rainfall. The storms lasted between 5.5 and 33??h, with average intensities between 1.3 and 20.4??mm/h, and had recurrence intervals of two years or less. Threshold rainfall conditions for life- and property-threatening floods and debris flows during the first winter season following fires in Ventura County, and in the San Bernardino, San Gabriel and San Jacinto Mountains of southern California are defined by I = 12.5D-0.4, and I = 7.2D-0.4, respectively. A threshold defined for flood and debris-flow conditions following a year of vegetative recovery and sediment removal for the San Bernardino, San Gabriel and San Jacinto Mountains of I = 14.0D-0.5 is approximately 25??mm/h higher than that developed for the first year following fires. The thresholds defined here are significantly lower than most identified for unburned settings, perhaps because of the difference between extremely rapid, runoff-dominated processes acting in burned areas and longer-term, infiltration-dominated processes on unburned hillslopes. Crown Copyright ?? 2007.

Geomorphology↗
USGS2008

Post-wildfire erosion response in two geologic terrains in the western USA

Volumes of eroded sediment after wildfires vary substantially throughout different geologic terrains across the western United States. These volumes are difficult to compare because they represent the response to rainstorms and runoff with different characteristics. However, by measuring the erosion response as the erodibility efficiency of water to detach and transport sediment on hillslopes and in channels, the erosion response from different geologic terrains can be compared. Specifically, the erodibility efficiency is the percentage of the total available stream power expended to detach, remobilize, or transport a mass of sediment. Erodibility efficiencies were calculated for the (i) initial detachment, and for the (ii) remobilization and transport of sediment on the hillslopes and in the channels after wildfire in two different geological terrains. The initial detachment efficiencies for the main channel and tributary channel in the granitic terrain were 10 ?? 9% and 5 ?? 4% and were similar to those for the volcanic terrain, which were 5 ?? 5% and 1 ?? 1%. No initial detachment efficiency could be measured for the hillslopes in the granitic terrain because hillslope measurements were started after the first major rainstorm. The initial detachment efficiency in the volcanic terrain was 1.3 ?? 0.41%. The average remobilization and transport efficiencies associated with flash floods in the channels also were similar in the granitic (0.18 ?? 0.57%) and volcanic (0.11 ?? 0.41%) terrains. On the hillslope the remobilization and transport efficiency was greater in the volcanic terrain (2.4%) than in the granitic terrain (0.65%). However, this may reflect the reduced sediment availability after the first major rainstorm (30-min maximum rainfall intensity ??? 90??mm h- 1) in the granitic terrain, while easily erodible fine colluvium remained on the hillslope after the first rainstorm (30-min maximum rainfall intensity = 7.2??mm h- 1) in the volcanic terrain. The erosion response in channels and on hillslopes of the granitic and volcanic terrains was similar when compared using erodibility efficiencies.

Geomorphology↗
USGS2001

Debris-flow generation from recently burned watersheds

Evaluation of the erosional response of 95 recently burned drainage basins in Colorado, New Mexico and southern California to storm rainfall provides information on the conditions that result in fire-related debris flows. Debris flows were produced from only 37 of 95 (~40 percent) basins examined; the remaining basins produced either sediment-laden streamflow or no discernable response. Debris flows were thus not the prevalent response of the burned basins. The debris flows that did occur were most frequently the initial response to significant rainfall events. Although some hillslopes continued to erode and supply material to channels in response to subsequent rainfall events, debris flows were produced from only one burned basin following the initial erosive event. Within individual basins, debris flows initiated through both runoff and infiltration-triggered processes. The fact that not all burned basins produced debris flows suggests that specific geologic and geomorphic conditions may control the generation of fire-related debris flows. The factors that best distinguish between debris-flow producing drainages and those that produced sediment-laden streamflow are drainage-basin morphology and lithology, and the presence or absence of water-repellent soils. Basins underlain by sedimentary rocks were most likely to produce debris flows that contain large material, and sand- and gravel-dominated flows were generated primarily from terrain underlain by decomposed granite. Basin-area and relief thresholds define the morphologic conditions under which both types of debris flows occur. Debris flows containing large material are more likely to be produced from basins without water-repellent soils than from basins with water repellency. The occurrence of sand-and gravel-dominated debris flows depends on the presence of water-repellent soils.

California↗
USGS2001

A process for fire-related debris flow initiation, Cerro Grande fire, New Mexico

In this study we examine factors that pertain to the generation of debris flows from a basin recently burned by wildfire. Throughout the summer 2000 thunderstorm season, we monitored rain gauges, channel cross-sections, hillslope transects, and nine sediment-runoff traps deployed in a steep, 0??15 km2 basin burned by the May 2000 Cerro Grande fire in New Mexico. Debris flows were triggered in the monitored basin during a rainstorm on July 16, 2000, in response to a maximum 30 min rainfall intensity of 31 mm h-1 (return period of approximately 2 years). Eleven other storms occurred before and after the July storm; these storms resulted in significant runoff, but did not generate debris flows. The debris flows generated by the July 16 storm initiated on a broad, open hillslope as levee-lined rills. The levees were composed of gravel- and cobble-sized material supported by an abundant fine-grained matrix. Debris-flow deposits were observed only on the hillslopes and in the first and second-order drainages of the monitored basin. No significant amounts of channel incision were measured following the passage of the debris flows, indicating that most of the material in the flows originated from the hillslopes. Sediment-runoff concentrations of between 0??23 and 0??81 kg 1-1 (with a mean of 0-42 kg 1-1) were measured from the hillslope traps following the debris-flow-producing storm. These concentrations, however, were not unique to the July 16 storm. The materials entrained by the July 16 storm contained a higher proportion of silt- plus clay-sized materials in the <2 mm fraction than the materials collected from storms that produced comparable sediment-runoff concentrations but not debris flows. The difference in materials demonstrates the critical role of the availability of fine-grained wood ash mantling the hillslopes in the runoff-dominated generation of post-wildfire debris flows. The highest sediment-runoff concentrations, again not unique to debris-flow production, were produced from maximum 30 min rainfall intensities greater than 20 mm h-1. Copyright ?? 2001 John Wiley and Sons, Ltd.

Hydrological Processes↗
USGS2001

Wildfire-related debris-flow initiation processes, Storm King Mountain, Colorado

A torrential rainstorm on September 1, 1994 at the recently burned hillslopes of Storm King Mountain, CO, resulted in the generation of debris flows from every burned drainage basin. Maps (1:5000 scale) of bedrock and surficial materials and of the debris-flow paths, coupled with a 10-m Digital Elevation Model (DEM) of topography, are used to evaluate the processes that generated fire-related debris flows in this setting. These evaluations form the basis for a descriptive model for fire-related debris-flow initiation. The prominent paths left by the debris flows originated in 0- and 1st-order hollows or channels. Discrete soil-slip scars do not occur at the heads of these paths. Although 58 soil-slip scars were mapped on hillslopes in the burned basins, material derived from these soil slips accounted for only about 7% of the total volume of material deposited at canyon mouths. This fact, combined with observations of significant erosion of hillslope materials, suggests that a runoff-dominated process of progressive sediment entrainment by surface runoff, rather than infiltration-triggered failure of discrete soil slips, was the primary mechanism of debris-flow initiation. A paucity of channel incision, along with observations of extensive hillslope erosion, indicates that a significant proportion of material in the debris flows was derived from the hillslopes, with a smaller contribution from the channels. Because of the importance of runoff-dominated rather than infiltration-dominated processes in the generation of these fire-related debris flows, the runoff-contributing area that extends upslope from the point of debris-flow initiation to the drainage divide, and its gradient, becomes a critical constraint in debris-flow initiation. Slope-area thresholds for fire-related debris-flow initiation from Storm King Mountain are defined by functions of the form Acr(tan ??)3 = S, where Acr is the critical area extending upslope from the initiation location to the drainage divide, and tan ?? is its gradient. The thresholds vary with different materials. ?? 2001 Elsevier Science B.V. All rights reserved.

Geomorphology↗
USGS2000

Conditions for generation of fire-related debris flows, Capulin Canyon, New Mexico

Comparison of the responses of three drainage basins burned by the Dome fire of 1996 in New Mexico is used to identify the hillslope, channel and fire characteristics that indicate a susceptibility specifically to wildfire-related debris flow. Summer thunderstorms generated three distinct erosive responses from each of three basins. The Capulin Canyon basin showed widespread erosive sheetwash and rilling from hillslopes, and severe flooding occurred in the channel; the North Tributary basin exhibited extensive erosion of the mineral soil to a depth of 5 cm and downslope movement of up to boulder-sized material, and at least one debris flow occurred in the channel; negligible surface runoff was observed in the South Tributary basin. The negligible surface runoff observed in the South Tributary basin is attributed to the limited extent and severity of the fire in that basin. The factors that best distinguish between debris-flow producing and flood-producing drainages are drainage basin morphology and lithology. A rugged drainage basin morphology, an average 12 per cent channel gradient, and steep, rough hillslopes coupled with colluvium and soil weathered from volcaniclastic and volcanic rocks promoted the generation of debris flows. A less rugged basin morphology, an average gradient of 5 per cent, and long, smooth slopes mantled with pumice promoted flooding. Flood and debris-flow responses were produced without the presence of water-repellent soils. The continuity and severity of the burn mosaic, the condition of the riparian vegetation, the condition of the fibrous root mat, accumulations of dry ravel and colluvial material in the channel and on hillslopes, and past debris-flow activity, appeared to have little bearing on the distinctive responses of the basins. Published in 2000 by John Wiley and Sons, Ltd.

Earth Surface Processes and Landforms↗
USGS1998

Fire-related hyperconcentrated and debris flows on Storm King Mountain, Glenwood Springs, Colorado, USA

The South Canyon Fire of July 1994 burned 800 ha of vegetation on Storm King Mountain near Glenwood Springs, Colorado, USA. On the night of 1 September 1994, in response to torrential rains, debris flows inundated seven areas along a 5-km length of interstate Highway 70. Mapping from aerial photographs, along with field observations and measurements, shows that the September rainstorm eroded unconsolidated, burned surficial soil from the hillsides, flushed dry-ravel deposits from the tributary channels, and transported loose, large material from the main channels. The hyperconcentrated flows and debris flows inundated 14 ha of Interstate Highway 70 with 70000 m3 of material. Although the burned area was seeded in November 1994, the potential for continuing debris-flow activity remains. Incision and entrainment of channel alluvium, as well as erosion of loose material from the hillslopes could result in future debris- and hyperconcentrated-flow activity.The South Canyon Fire of July 1994 burned 800 ha of vegetation on Storm King Mountain near Glenwood Springs, Colorado, USA. On the night of 1 September 1994, in response to torrential rains, debris flows inundated seven areas along a 5-km length of Interstate Highway 70. Mapping from aerial photographs, along with field observations and measurements, shows that the September rainstorm eroded unconsolidated, burned surficial soil from the hillsides, flushed dry-ravel deposits from the tributary channels, and transported loose, large material from the main channels. The hyperconcentrated flows and debris flows inundated 14 ha of Interstate Highway 70 with 70000 m3 of material. Although the burned area was seeded in November 1994, the potential for continuing debris-flow activity remains. Incision and entrainment of channel alluvium, as well as erosion of loose material from the hillslopes could result in future debris- and hyperconcentrated-flow activity.

Environmental Geology↗
USGS1998

Slope failure and shoreline retreat during northern California's latest El Nino

Surface processes accelerated by severe storms during the 1997–1998 El Niño event scoured hillsides and damaged property across coastal California. Technological advances such as digital mapping, exemplified here for the San Francisco Bay area but applicable elsewhere, have enabled government agencies to better describe, monitor, and predict the effects of shoreline erosion and slope failure.

California↗