Search USGS⌕ Search

Geology topics

S. T. Algermissen

Publications and source records attributed to S. T. Algermissen.

At least 19 recordsLinked to original sources
USGS1993

Pilot studies of seismic hazard and risk in North Sulawesi Province, Indonesia

Earthquake ground motions in North Sulawesi on soft soil that have a 90% probability of not been exceeded in 560 years are estimated to be 0.63 g (63% of the acceleration of gravity) at Palu, 0.31 g at Gorontalo, and 0.27 g at Manado. Estimated ground motions for rock conditions for the same probability level and exposure time are 56% of those for soft soil. The hazard estimates are obtained from seismic sources that model the earthquake potential to a depth of 100 km beneath northern and central Sulawesi and include the Palu fault zone of western Sulawesi, the North Sulawesi subduction zone, and the southern most segment of the Sangihe subduction zone beneath the Molucca Sea. An attenuation relation based on Japanese strong-motion data and considered appropriate for subduction environments of the western Pacific was used in determination of ground motions. Following the 18 April 1990 North Sulawesi earthquake (Ms 7.3) a seismic hazard and risk assessment was carried out. -from Authors

Earthquake Spectra↗
USGS1992

Progress report on the Worldwide Earthquake Risk Management (WWERM) Program

Considerable progress has been made in the Worldwide Earthquake Risk Management (WWERM) Program since its initiation in late 1989 as a cooperative program of the Agency for International Development (AID), Office of U.S. Foreign Disaster Assistance (OFDA), and the U.S. Geological Survey. Probabilistic peak acceleration and peak Modified Mercalli intensity (MMI) maps have been prepared for Chile and for Sulawesi province in Indonesia. Earthquake risk (loss) studies for dwellings in Gorontalo, North Sulawesi, have been completed and risk studies for dwellings in selected areas of central Chile are underway. A special study of the effect of site response on earthquake ground motion estimation in central Chile has also been completed and indicates that site response may modify the ground shaking by as much as plus or minus two units of MMI. A program for the development of national probabilistic ground motion maps for the Philippines is now underway and pilot studies of earthquake ground motion and risk are being planned for Morocco.

Conference Paper↗
USGS1991

Seismicity map of the state of Georgia

This map is one of a series of seismicity maps produced by the U.S. Geological Survey that show earthquake data of individual states or groups of states at the scale of 1:1,000,000. This maps shows only those earthquakes with epicenters located within the boundaries of Georgia, even though earthquakes in nearby states or countries may have been felt or may have cause damage in Georgia. The data in table 1 were used to compile the seismicity map; these data are a corrected, expanded, and updated (through 1987) version of the data used by Algermissen (1969) for a study of seismic risk in the United States. The locations and intensities of some earthquakes were revised and intensities were assigned where none had been before. Many earthquakes were added to the original list from new data sources as well as from some old data sources that has not been previously used. The data in table 1 represent best estimates of the location of the epicenter, magnitude, and intensity of each earthquake on the basis of historical and current information. Some of the aftershocks from large earthquakes are listed, but not all, especially for earthquakes that occurred before seismic instruments were universally used. The latitude and longitude coordinates of each epicenter were rounded to the nearest tenth of a degree and sorted so that all identical locations were grouped and counted. These locations are represented on the map by a triangle. The number of earthquakes at each location is shown on the map by the Arabic number to the right of the triangle. A Roman numeral to the left of a triangle is the maximum Modified Mercoili intensity (Wood and Neumann, 1931) of all earthquakes at that geographic location, The absence of an intensity value indicates that no intensities have been assigned to earthquakes at that location. The year shown below each triangle is the latest year for which the maximum intensity was recorded.

Georgia↗
USGS1991

Seismicity map of the state of Idaho

This map is one of a series of seismicity maps produced by the U.S. Geological Survey that show earthquake data of individual states or groups of states at the scale of 1:1,000,000. This map shows only those earthquakes with epicenters located within the boundaries of Idaho, even though earthquakes in nearby states or countries may have been felt or may have caused damage in Idaho. The data in table 1 were used to compile the seismicity map; these data are a corrected, expanded, and updated (through 1987) version of the data used by Algermissen (1969) for a study of seismic risk in the United States. The locations and intensities of some earthquakes were revised and intensities were assigned where none had been before. Many earthquakes were added to the original list from new data sources as well as from some old data sources that had not been previously used. The data in table 1 represent earthquake on the basis of historical and current information. Some of the aftershocks from large earthquake are listed, but not all, especially for earthquakes that occurred before seismic instruments were universally used. The latitude and longitude coordinates of each epicenter were rounded to the nearest tenth of a degree and sorted so that all identical locations were grouped and counted. These locations are represented on the map by a triangle. The number of earthquakes at each location is shown on the map by the Arabic number to the right of the triangle. A Roman numeral to the left of a triangle is the maximum Modified Mercalli intensity (Wood and Neumann, 1931) of all earthquakes at that geographic location. The absence of an intensity value indicates that no intensities have been assigned to earthquakes at that location. The year shown below each triangle is the latest year for which the maximum intensity was recorded.

Idaho↗
USGS1990

Probabilistic earthquake acceleration and velocity maps for the United States and Puerto Rico

The ground-motion maps presented here (maps A-D) show the expected seismic induced or earthquake caused maximum horizontal acceleration and velocity in rock in the contiguous United States, Alaska, Hawaii, and Puerto Rico. There is a 90 percent probability that the maximum horizontal acceleration and velocity shown on the maps will not be exceeded in the time periods of 50 and 250 years (average return period for the expected ground motion of 474 and 2,372 years). Rock is taken here to mean material having a shear-wave velocity of between 0.75 and 0.90 kilometers per second. (Algermissen and Perkins, 1976).

Miscellaneous Field Studies Map↗
USGS1988

Seismicity map of the state of Texas

This map is one of a series of seismicity maps produced by the U.S. Geological Survey that show earthquake data of individual states or groups of states at the scale of 1:1,000,000. This map shows only those earthquakes with epicenters located within the boundaries of Texas, even though earthquakes in nearby states may have been felt or may have caused damage in Texas. The data in table 1 were used to compile the seismicity map; these data are a corrected, expanded, and updated (through 1987) version of the data used by Algermissen (1969) for a study of seismic risk in the United States. The locations and intensities of some earthquakes were revised and intensities were assigned where none had been before. Many earthquakes were added to the original list from new data sources as well as from some old data sources that has not been previously used. The data in table 1 represent best estimates of the location of the epicenter, magnitude, and intensity of each earthquake on the basis of historical and current information. Some of the aftershocks from large earthquakes are listed, but not all, especially for earthquakes that occurred before seismic instruments were universally used.

Texas↗
USGS1988

Seismicity map of the state of New Mexico

This map is one of a series of seismicity maps produced by the U. S. Geological Survey that show earthquake data of individual states or groups of states at the scale of 1:1,000,000. This map shows only those earthquakes with epicenters located within the boundaries of New Mexico, even though earthquakes in nearby states or countries may have been felt or may have caused damage in New Mexico. The data in table 1 were used to compile the seismicity map; these data are a corrected, expanded, and updated (through 1983) version of the data used by Algermissen (1969) for a study of seismic risk in the United States. The locations and intensities of some earthquakes were revised and intensities were assigned where none had been before. Many earthquakes were added to the original list from new data sources as well as from some old data sources that had not been previously used. The data in table 1 represent best estimates of the location of the epicenter, magnitude, and intensity of each earthquake on the basis of historical and current information. Some of the aftershocks from large earthquakes are listed, but not all, especially for earthquakes that occurred before seismic instruments were universally used.

New Mexico↗
USGS1988

Seismicity map of the state of Colorado

This map is one of a series of seismicity maps produced by the U.S. Geological Survey that show earthquake data of individual states or groups of states at the scale of 1:1,000,000. This map shows only those earthquakes with epicenters located within the boundaries of Colorado, even though earthquakes in nearby states may have been felt or may have caused damage in Colorado. The data in table 1 were used to compile the seismicity map; these data are a corrected, expanded, and updated (through 1987) version of the data used by Algermissen (1969) for a study of seismic risk in the United States. The locations and intensities of some earthquakes were revised and intensities were assigned where none had been before. Many earthquakes were added to the original list from new data sources as well as from some old data sources that has not been previously used. The data in table 1 represent best estimates of the location of the epicenter, magnitude, and intensity of each earthquake on the basis of historical and current information. Some of the aftershocks from large earthquakes are listed, but not all, especially for earthquakes that occurred before seismic instruments were universally used.

Colorado↗
USGS1987

Seismicity map of the state of Georgia

This map is one of a series of seimicity maps produced by the U.S. Geological Survey that show earthquake data of individual states or groups of states at the scale of 1:1,000,000. This map shows only those earthquakes with epicenters located within the boundaries of Georgia, even though earthquakes in nearby states or countries may have been felt or may have caused damage in Georgia.

Georgia↗
USGS1987

Seismicity map of the state of Louisiana

This map is one of a series of seismicity maps produced by the U.S. Geological Survey that show earthquake data of individual states or groups of states at the scale of 1:1,000,000. This map shows only those earthquakes with epicenters located within the boundaries of Louisiana, even though earthquakes in nearby states may have been felt or may have caused damage in Louisiana. The data in table 1 were used to compile the seismicity map; these data are a corrected, expanded, and updated (through 1987) version of the data used by Algermissen (1969) for a study of seismic risk in the United States. The locations and intensities of some earthquakes were revised and intensities were assigned where none had been before. Many earthquakes were added to the original list from new data sources as well as from some old data sources that has not been previously used. The data in table 1 represent best estimates of the location of the epicenter, magnitude, and intensity of each earthquake on the basis of historical and current information. Some of the aftershocks from large earthquakes are listed, but not all, especially for earthquakes that occurred before seismic instruments were universally used.

Louisiana↗
USGS1987

Seismicity map of the state of Kentucky

This map is one of a series of seismicity maps produced by the U.S. Geological Survey that show earthquake data of individual states or groups of states at the scale of 1:1,000,000. This map shows only those earthquakes with epicenters located within the boundaries of Kentucky, even though earthquakes in nearby states or countries may have been felt or may have caused damage in Kentucky.

Kentucky↗
USGS1987

Seismicity map of the state of Tennessee

This map is one of a series of seismicity maps produced by the U.S. Geological Survey that show earthquake data of individual states or groups of states at the scale of 1:1,000,000. This map shows only those earthquakes with epicenters located within the boundaries of Tennessee, even though earthquakes in nearby states or countries may have been felt or may have caused damage in Tennessee.

Tennessee↗
USGS1987

Seismicity map of the state of Pennsylvania

This map is one of a series of seismicity maps produced by the U. S. Geological Survey that show earthquake data of individual states or groups of states at the scale of 1:1,000,000. This map shows only those earthquakes with epicenters located within the boundaries of Pennsylvania, even though earthquakes in nearby states may have been felt or may have caused damage in Pennsylvania. The data in table 1 were used to compile the seismicity map; these data are a corrected, expanded, and updated (through 1983) version of the data used by Algermissen (1969) for a study of seismic risk in the United States. The locations and intensities of some earthquakes were revised and intensities were assigned where none had been before. Many earthquakes were added to the original list from new data sources as well as from some old data sources that had not been previously used. The data in table 1 represent best estimates of the location of the epicenter, magnitude, and intensity of each earthquake on the basis of historical and current information. Some of the aftershocks from large earthquakes are listed, but not all, especially for earthquakes that occurred before seismic instruments were universally used. The latitude and longitude coordinates of each epicenter were rounded to the nearest tenth of a degree and sorted so that all identical locations were grouped and counted. These locations are represented on the map by a triangle. The number of earthquakes at each location is shown on the map by the arabic number to the right of the triangle. A Roman numeral to the left of a triangle is the maximum Modified Mercalli intensity (Wood and Neumann, 1931) of a11 earthquakes at that geographic location. The absence of an intensity value indicates that no intensities have been assigned to earthquakes at that location. The year shown below each triangle is the latest year for which the maximum intensity was recorded.

Pennsylvania↗
USGS1987

Seismicity map of the state of New York

This map is one of a series of seismicity maps produced by the U.S. Geological Survey that show earthquake data of individual states or groups of states at the scale of 1:1,000,000. This map shows only those earthquakes with epicenters located within the boundaries of New York, even though earthquakes in nearby states or countries may have been felt or may have caused damage in New York.

New York↗
USGS1987

Seismicity map of the state of Indiana

This map is one of a series of seismicity maps produced by the U. S. Geological Survey that show earthquake data of individual states or groups of states at the scale of 1:1,000,000. This map shows only those earthquakes with epicenters located within the boundaries of Indiana, even though earthquakes in nearby states may have been felt or may have caused damage in Indiana. The data in table 1 were used to compile the seismicity map; these data are a corrected, expanded, and updated (through 1983) version of the data used by Algermissen (1969) for a study of seismic risk in the United States. The locations and intensities of some earthquakes were revised and intensities were assigned where none had been before. Many earthquakes were added to the original list from new data sources as well as from some old data sources that had not been previously used. The data in table 1 represent best estimates of the location of the epicenter, magnitude, and intensity of each earthquake on the basis of historical and current information. Some of the aftershocks from large earthquakes are listed, but not all, especially for earthquakes that occurred before seismic instruments were universally used. The latitude and longitude coordinates of each epicenter were rounded to the nearest tenth of a degree and sorted so that all identical locations were grouped and counted. These locations are represented on the map by a triangle. The number of earthquakes at each location is shown on the map by the arabic number to the right of the triangle. A Roman numeral to the left of a triangle is the maximum Modified Mercalli intensity (Wood and Neumann, 1931) of all earthquakes at that geographic location. The absence of an intensity value indicates that no intensities have been assigned to earthquakes at that location. The year shown below each triangle is the latest year for which the maximum intensity was recorded.

Indiana↗
USGS1987

Seismicity map of the state of Ohio

This map is one of a series of seismicity maps produced by the U. S. Geological Survey that show earthquake data of individual states or groups of states at the scale of 1:1,000,000. This map shows only those earthquakes with epicenters located within the boundaries of Ohio, even though earthquakes in nearby states or countries may have been felt or may have caused damage in Ohio. The data in table 1 were used to compile the seismicity map; these data are a corrected, expanded, and updated (through 1983) version of the data used by Algermissen (1969) for a study of seismic risk in the United States. The locations and intensities of some earthquakes were revised and intensities were assigned where none had been before. Many earthquakes were added to the original list from new data sources as well as from some old data sources that had not been previously used. The data in table 1 represent best estimates of the location of the epicenter, magnitude, and intensity of each earthquake on the basis of historical and current information. Some of the aftershocks from large earthquakes are listed, but not all, especially for earthquakes that occurred before seismic instruments were universally used. The latitude and longitude coordinates of each epicenter were rounded to the nearest tenth of a degree and sorted so that all identical locations were grouped and counted . These locations are represented on the map by a triangle. The number of earthquakes at each location is shown on the map by the arabic number to the right of the triangle. A Roman numeral to the left of a triangle is the maximum Modified Mercalli intensity (Wood and Neumann, 1931) of all earthquakes at that geographic location. The absence of an intensity value indicates that no intensities have been assigned to earthquakes at that location. The year shown below each triangle is the latest year for which the maximum intensity was recorded.

Ohio↗