Search USGS⌕ Search

Geology topics

S. Hickman

Publications and source records attributed to S. Hickman.

13 recordsLinked to original sources
USGS2012

Stress measurements at depth in the vicinity of the San Andreas fault. Implications for the magnitude of shear stress at depth

Using the hydraulic fracturing technique, we have made a systematic series of in situ stress measurements in wells drilled near the San Andreas fault. In an attempt to provide constraints for the magnitude of shear stress on the San Andreas fault at depth we have measured both the variation of stress with distance from the fault in relatively shallow (∼230 m) wells and the variation of stress with depth in a ∼1-km-deep well located 4 km from the fault. The shallow wells are located along profiles roughly perpendicular to the fault in the western Mojave desert near Palmdale and in central California where the fault is creeping. In both areas the direction of maximum compression was found to be approximately 45° from the local trend of the San Andreas. The two stress profiles show very similar results: (1) shear stress (on planes parallel to the San Andreas) increases with distance from the fault, more markedly in the western Mojave, (2) the far-field shear stress at ∼200 m depth is ∼50 bars, and (3) the horizontal principal stresses as well as shear stress increase with depth more rapidly in the wells farthest from the fault. The ∼1-km-deep well, also located in the western Mojave desert, shows increases of both horizontal principal stresses and shear stress with depth. Shear stress increases from about 25 bars at 150–300 m to about 80 bars at 750–850 m. Although this rapid increase of shear stress with depth suggests that the mean shear stress on the fault at seismogenic depths exceeds several hundred bars, the principal stresses increase with depth in a steplike manner. As this may be a near-surface effect, extrapolation of the measurements to much greater depths may not be warranted.

Journal of Geophysical Research Solid Earth↗
USGS2011

U.S. Department of Energy's site screening, site selection, and initial characterization for storage of CO 2 in deep geological formations

The U.S. Department of Energy (DOE) is the lead Federal agency for the development and deployment of carbon sequestration technologies. As part of its mission to facilitate technology transfer and develop guidelines from lessons learned, DOE is developing a series of best practice manuals (BPMs) for carbon capture and storage (CCS). The "Site Screening, Site Selection, and Initial Characterization for Storage of CO 2 in Deep Geological Formations" BPM is a compilation of best practices and includes flowchart diagrams illustrating the general decision making process for Site Screening, Site Selection, and Initial Characterization. The BPM integrates the knowledge gained from various programmatic efforts, with particular emphasis on the Characterization Phase through pilot-scale CO 2 injection testing of the Validation Phase of the Regional Carbon Sequestration Partnership (RCSP) Initiative. Key geologic and surface elements that suitable candidate storage sites should possess are identified, along with example Site Screening, Site Selection, and Initial Characterization protocols for large-scale geologic storage projects located across diverse geologic and regional settings. This manual has been written as a working document, establishing a framework and methodology for proper site selection for CO 2 geologic storage. This will be useful for future CO 2 emitters, transporters, and storage providers. It will also be of use in informing local, regional, state, and national governmental agencies of best practices in proper sequestration site selection. Furthermore, it will educate the inquisitive general public on options and processes for geologic CO 2 storage. In addition to providing best practices, the manual presents a geologic storage resource and capacity classification system. The system provides a "standard" to communicate storage and capacity estimates, uncertainty and project development risk, data guidelines and analyses for adequate site characterization, and guidelines for reporting estimates within the classification based on each project's status.

Conference Paper↗
USGS2008

Paleomagnetic reorientation of San Andreas Fault Observatory at Depth (SAFOD) core

We present a protocol for using paleomagnetic analysis to determine the absolute orientation of core recovered from the SAFOD borehole. Our approach is based on determining the direction of the primary remanent magnetization of a spot core recovered from the Great Valley Sequence during SAFOD Phase 2 and comparing its direction to the expected reference field direction for the Late Cretaceous in North America. Both thermal and alternating field demagnetization provide equally resolved magnetization, possibly residing in magnetite, that allow reorientation. Because compositionally similar siltstones and fine-grained sandstones were encountered in the San Andreas Fault Zone during Stage 2 rotary drilling, we expect that paleomagnetic reorientation will yield reliable core orientations for continuous core acquired from directly within and adjacent to the San Andreas Fault during SAFOD Phase 3, which will be key to interpretation of spatial properties of these rocks. Copyright 2008 by the American Geophysical Union.

Geophysical Research Letters↗
USGS2008

Physical rock properties in and around a conduit zone by well-logging in the Unzen Scientific Drilling Project, Japan

The objective of the Unzen Scientific Drilling Project (USDP) is not only to reveal the structure and eruption history of the Unzen volcano but also to clarify the ascent and degassing mechanisms of the magma conduit. Conduit drilling (USDP-4) was conducted in 2004, which targeted the magma conduit for the 1990-95 eruption. The total drilled length of USDP-4 was 1995.75??m. Geophysical well logging, including resistivity, gamma-ray, spontaneous potential, sonic-wave velocity, density, neutron porosity, and Fullbore Formation MicroImager (FMI), was conducted at each drilling stage. Variations in the physical properties of the rocks were revealed by the well-log data, which correlated with not only large-scale formation boundaries but also small-scale changes in lithology. Such variations were evident in the lava dike, pyroclastic rocks, and breccias over depth intervals ranging from 1 to 40??m. These data support previous models for structure of the lava conduit, in that they indicate the existence of alternating layers of high-resistivity and high P-wave velocity rocks corresponding to the lava dikes, in proximity to narrower zones exhibiting high porosity, low resistivity, and low P-wave velocity. These narrow, low-porosity zones are presumably higher in permeability than the adjacent rocks and may form preferential conduits for degassing during magma ascent. ?? 2008 Elsevier B.V.

Journal of Volcanology and Geothermal Research↗
USGS2007

Stress orientations of Taiwan Chelungpu-Fault Drilling Project (TCDP) hole-A as observed from geophysical logs

[1] The Taiwan Chelungpu-fault Drilling Project (TCDP) drilled a 2-km-deep research borehole to investigate the structure and mechanics of the Chelungpu Fault that ruptured in the 1999 M w 7.6 Chi-Chi earthquake. Geophysical logs of the TCDP were carried out over depths of 500–1900 m, including Dipole Sonic Imager (DSI) logs and Formation Micro Imager (FMI) logs in order to identify bedding planes, fractures and shear zones. From the continuous core obtained from the borehole, a shear zone at a depth of 1110 meters is interpreted to be the Chelungpu fault, located within the Chinshui Shale, which extends from 1013 to 1300 meters depth. Stress-induced borehole breakouts were observed over nearly the entire length of the wellbore. These data show an overall stress direction (∼N115°E) that is essentially parallel to the regional stress field and parallel to the convergence direction of the Philippine Sea plate with respect to the Eurasian plate. Variability in the average stress direction is seen at various depths. In particular there is a major stress orientation anomaly in the vicinity of the Chelungpu fault. Abrupt stress rotations at depths of 1000 m and 1310 m are close to the Chinshui Shale's upper and lower boundaries, suggesting the possibility that bedding plane slip occurred during the Chi-Chi earthquake.

Geophysical Research Letters↗
USGS2004

Stress orientations and magnitudes in the SAFOD pilot hole

Borehole breakouts and drilling-induced tensile fractures in the 2.2-km-deep SAFOD pilot hole at Parkfield, CA, indicate significant local variations in the direction of the maximum horizontal compressive stress, SHmax, but show a generalized increase in the angle between SHmax and the San Andreas Fault with depth. This angle ranges from a minimum of 25 ?? 10?? at 1000-1150 m to a maximum of 69 ?? 14?? at 2050-2200 m. The simultaneous occurrence of tensile fractures and borehole breakouts indicates a transitional strike-slip to reverse faulting stress regime with high horizontal differential stress, although there is considerable uncertainty in our estimates of horizontal stress magnitudes. If stress observations near the bottom of the pilot hole are representative of stresses acting at greater depth, then they are consistent with regional stress field indicators and an anomalously weak San Andreas Fault in an otherwise strong crust. Copyright 2004 by the American Geophysical Union.

Geophysical Research Letters↗
USGS2004

A mechanical model of the San Andreas fault and SAFOD Pilot Hole stress measurements

Stress measurements made in the SAFOD pilot hole provide an opportunity to study the relation between crustal stress outside the fault zone and the stress state within it using an integrated mechanical model of a transform fault loaded in transpression. The results of this modeling indicate that only a fault model in which the effective friction is very low (<0.1) through the seismogenic thickness of the crust is capable of matching stress measurements made in both the far field and in the SAFOD pilot hole. The stress rotation measured with depth in the SAFOD pilot hole (???28??) appears to be a typical feature of a weak fault embedded in a strong crust and a weak upper mantle with laterally variable heat flow, although our best model predicts less rotation (15??) than observed. Stress magnitudes predicted by our model within the fault zone indicate low shear stress on planes parallel to the fault but a very anomalous mean stress, approximately twice the lithostatic stress. Copyright 2004 by the American Geophysical Union.

Geophysical Research Letters↗
USGS2004

The Coso EGS project - Recent developments

An Engineered Geothermal System (EGS) field experiment will be conducted to hydraulically stimulate injection well 34-9RD2, located on the east flank of the Coso geothermal reservoir, with the objective of increasing the injection rate of this well to 750 gpm at a wellhead pressure of 100 psi or less. The stimulation of this well is expected to create hydraulic communication with the recently drilled production well 38C-9, which is directly south of 34-9RD2. We summarize the results of fracture and stress analyses based upon borehole image logs of 38C-9; petrographic and petrologic analyses of cuttings from both the injection well 34-9RD2 and the production well 38C-9; and plans for the redrilling and stimulation of 34-9RD2.

California↗
USGS2003

Topographically driven groundwater flow and the San Andreas heat flow paradox revisited

Evidence for a weak San Andreas Fault includes (1) borehole heat flow measurements that show no evidence for a frictionally generated heat flow anomaly and (2) the inferred orientation of ??1 nearly perpendicular to the fault trace. Interpretations of the stress orientation data remain controversial, at least in close proximity to the fault, leading some researchers to hypothesize that the San Andreas Fault is, in fact, strong and that its thermal signature may be removed or redistributed by topographically driven groundwater flow in areas of rugged topography, such as typify the San Andreas Fault system. To evaluate this scenario, we use a steady state, two-dimensional model of coupled heat and fluid flow within cross sections oriented perpendicular to the fault and to the primary regional topography. Our results show that existing heat flow data near Parkfield, California, do not readily discriminate between the expected thermal signature of a strong fault and that of a weak fault. In contrast, for a wide range of groundwater flow scenarios in the Mojave Desert, models that include frictional heat generation along a strong fault are inconsistent with existing heat flow data, suggesting that the San Andreas Fault at this location is indeed weak. In both areas, comparison of modeling results and heat flow data suggest that advective redistribution of heat is minimal. The robust results for the Mojave region demonstrate that topographically driven groundwater flow, at least in two dimensions, is inadequate to obscure the frictionally generated heat flow anomaly from a strong fault. However, our results do not preclude the possibility of transient advective heat transport associated with earthquakes.

Journal of Geophysical Research B: Solid Earth↗
USGS2001

Hydrothermal minerals and microstructures in the Silangkitang geothermal field along the Great Sumatran fault zone, Sumatra, Indonesia

Detailed study of core samples of silicic tuff recovered from three geothermal wells along the strike-slip Great Sumatran fault zone near Silangkitang, North Sumatra, supports a model for enhanced hydrothermal circulation adjacent to this major plate-boundary fault. Two wells (A and C) were drilled nearly vertically ∼1 km southwest of the eastern (i.e., the principal) fault trace, and the third, directional well (B) was drilled eastward from the site of well A to within ∼100 m of the principal fault trace. The examined core samples come from depths of 1650–2120 m at measured well temperatures of 180–320 °C. The samples collected near the principal fault trace have the highest temperatures, the largest amount of secondary pore space that correlates with high secondary permeability, and the most extensive hydrothermal mineral development. Secondary permeability and the degree of hydrothermal alteration decrease toward the southwestern margin of the fault zone. These features indicate episodic, localized flow of hot, possibly CO 2 -rich fluids within the fault zone. The microstructure populations identified in the core samples correlate to the subsidiary fault patterns typical of strike-slip faults. The geothermal reservoir appears to be centered on the fault zone, with the principal fault strands and adjoining, highly fractured and hydrothermally altered rock serving as the main conduits for vertical fluid flow and advective heat transport from deeper magmatic sources.

Great Sumatran Fault Zone, Sumatra↗
USGS1997

Analysis of borehole televiewer measurements in the Vorotilov drillhole, Russia - First results

In the Eurasian part of the World Stress Map almost the whole region east of the Tornquist-Teisseyre line is terra incognita. The closure of this information gap is of fundamental importance to the understanding of the geodynamics of the Eurasian continent. A detailed analysis of stress-induced wellbore breakouts has been performed over a 4.1-km-long depth interval in the Vorotilov drillhole (VGS). The borehole is located in the central part of the Russian platform, right in the center of the Vorotilov meteorite impact crater 60 km to the NNE of the city of Nizni Novgorod. An ultrasonic borehole televiewer (BHTV) was used to obtain high-resolution acoustical images from the borehole wall. With an interactive system for analyzing BHTV data the azimuth and shape of borehole breakouts occurring in the depth range of 1.3–4.8 km were analyzed. A statistical analysis of the resulting orientation profile of the breakout azimuths yields an overall direction of the maximum horizontal principal stress S H of N 137°E ± 15°. Variations of breakout orientation with depth ranging from a few degrees up to more than 90° are seen on various depth scales. The observed stress direction of N 137°E agrees very well with the average S H orientation of N 145°E in Central Europe. If this measurement is taken as representative for the Russian platform, the stress field in Russia is only slightly rotated in comparison to Central Europe. This can possibly be interpreted as indicative for the stress field to be governed by broad scale tectonic forces, such as a strong contribution from the forces exerted by the collision zone in the Alpine-Himalayan belt and by the Mid-Atlantic ridge.

Vorotilov drillhole↗