Ronald Litwin | Search USGS

USGS2024

Unified 200 kyr paleohydrologic history of the Southern Great Basin: Death Valley, Searles Valley, Owens Valley and the Devils Hole cave

We present a hydroclimate synthesis of the southern Great Basin over the last two glacial-interglacial cycles focused on paleolakes in Death Valley (core DV93-1), Searles Valley (core SLAPP-SRLS17), Owens Valley (core OL92), and the Devils Hole cave. There is close agreement between the occurrence of lakes in Death Valley and the height of the water table in the Devils Hole (50 km east of Death Valley) during the last 200 kyr. Death Valley and Devils Hole have adjacent, partly overlapping, drainage areas and most likely did over the last 200 kyr. When the water table in the Devils Hole was above the threshold level of ∼5 m higher than the modern, permanent lakes existed in Death Valley. At water table elevations less than 5 m above the modern, ephemeral lakes, saline pans, and mudflats occurred in Death Valley. The close temporal agreement between inferred paleoenvironments from the sediments in the Death Valley core and the paleowater table elevation in Devils Hole suggests a common forcing and provides insight into climate variability in the southwestern United States over the last 200 kyr. Owens Valley and Searles Valley, which derived inflow waters from the Sierra Nevada via the Owens River, contain paleohydrologic records which match those from Death Valley and the Devils Hole in terms of timing and direction of water availability over the last 200 kyr, indicating a similar paleohydrologic history for the entire southern Great Basin region. Near the end of Marine Oxygen Isotope Stage 6 (MIS 6), 140 ka - 130 ka, Lake Manly in Death Valley became shallow and hypersaline, and ultimately dried up at 127.1 ka ±4.3 ka. The transition from glacial to interglacial vegetation, which involved the loss of Juniperus pollen and an increase in Quercus (oak) pollen, occurred in Death Valley core DV93-1 at 131.3 ka ±4.0 ka. Following the glacial to interglacial pollen shift, a large alkaline lake formed in Death Valley. Similar conditions (freshwater, high productivity, and a mixed, deeply oxygenated water column indicated by biomarkers) existed in Searles Lake between 135.3 +2.7 / -2.9 ka and 130.1 +2.7 / -2.6 ka, also following the juniper-oak pollen transition. Sr isotopes in calcite and sulfate minerals (gypsum, glauberite, thenardite), and the rare occurrence of the sodium carbonate mineral northupite with a low 87 Sr/ 86 Sr ratio in core DV93-1, together with organic geochemical proxies from Searles core SLAPP-SRLS17, all suggest that at this time, late MIS 6 Lake Manly in Death Valley received alkaline water via spillover from Searles Valley into Death Valley through Panamint Valley. The hydrologic connection between Searles Valley, Panamint Valley, and Death Valley at Termination II (130 ka) is documented here for this system of pluvial lakes for the first time. The Devils Hole water table decreased to +6.5 m at 140.8 ka ±3.2 ka, rose briefly to +8 m at 137.6 ka ±0.5 ka, and then dropped 8 m by 120.36 ka ±0.45 ka, when it reached an elevation similar to the modern. The pluvial lakes in Death Valley and Searles Valley may have coincided with the rise of the Devils Hole water table at ∼137.6 ka ±0.5 ka years ago, although the age models for core DV93-1 and core SLAPP-SLRS17 during the end of MIS 6 carry large uncertainties.

Quaternary Science Reviews↗

USGS2019

Chesapeake Bay impact structure—Development of "brim" sedimentation in a multilayered marine target

The late Eocene Chesapeake Bay impact structure was formed in a multilayered target of seawater underlain sequentially by a sediment layer and a rock layer in a continental-shelf environment. Impact effects in the “brim” (annular trough) surrounding and adjacent to the transient crater, between the transient crater rim and the outer margin, primarily were limited to the target-sediment layer. Analysis of published and new lithostratigraphic, biostratigraphic, sedimentologic, petrologic, and mineralogic studies of three core holes, and published studies of a fourth core hole, provided information for the interpretation of the impact processes, their interactions and relative timing, their resulting products, and sedimentation in the brim. Most studies of marine impact-crater materials have focused on those found in the central crater. There are relatively few large, complex marine craters, of which most display a wide brim around the central crater. However, most have been studied using minimal data sets. The large number of core holes and seismic profiles available for study of the Chesapeake Bay impact structure presents a special opportunity for research. The physical and chronologic records supplied by study of the sediment and rock cores of the Chesapeake Bay impact indicate that the effects of the initial, short-lived contact and compression and excavation stages of the impact event primarily were limited to the transient crater. Only secondary effects of these processes are evident in the brim. The preserved record of the brim was created primarily in the subsequent modification stage. In the brim, the records of early impact processes (e.g., outgoing tsunamis, overturned flap collapse) were modified or removed by later processes. Transported and rotated, large and small clasts of target sediments, and intervals of fluidized sands indicate that seismic shaking fractured and partially fluidized the Cretaceous and Paleogene target sediments, which led to their inward transport by collapse and lateral spreading toward the transient crater. The succeeding inward seawater-resurge flow quickly overtook and interacted with the lateral spreading, further facilitating sediment transport across the brim and into the transient crater. Variations in the cohesion and relative depth of the target sediments controlled their degree of disaggregation and redistribution during these events. Melt clasts and shocked and unshocked rock clasts in the resurge sediments indicate fallout from the ejecta curtain and plume. Basal parautochthonous remnant sections of target Cretaceous sediments in the brim thin toward the collapsed transient crater. Overlying seawater-resurge deposits consist primarily of diamictons that vary laterally in thickness, and vertically and laterally in maximum grain size. After cessation of resurge flow and re-establishment of pre-impact sea level, sandy sediment gravity flows moved from the margin to the center of the partially filled impact structure (shelf basin). The uppermost unit consists of stratified sediments deposited from suspension. Postimpact clayey silts cap the crater fill and record the return to shelf sedimentation at atypically large paleodepths within the shelf basin. An unresolved question involves a section of gravel and sand that overlies Neoproterozoic granite in the inner part of the brim in one core hole. This section may represent previously unrecognized, now parautochthonous Cretaceous sediments lying nonconformably above basement granite, or it may represent target sediments that were moved significant distances by lateral spreading above basement rocks or above a granite megaclast from the overturned flap. The Chesapeake Bay impact structure is perhaps the best documented example of the small group of multilayer, marine-target impacts formed in continental shelves or beneath epeiric seas.

Chesapeake Bay↗