Search USGS⌕ Search

Geology topics

R. B. Finkelman

Publications and source records attributed to R. B. Finkelman.

At least 19 recordsLinked to original sources
USGS2011

Nitrogen in Chinese coals

Three hundred and six coal samples were taken from main coal mines of twenty-six provinces, autonomous regions, and municipalities in China, according to the resource distribution and coal-forming periods as well as the coal ranks and coal yields. Nitrogen was determined by using the Kjeldahl method at U. S. Geological Survey (USGS), which exhibit a normal frequency distribution. The nitrogen contents of over 90% Chinese coal vary from 0.52% to 1.41% and the average nitrogen content is recommended to be 0.98%. Nitrogen in coal exists primarily in organic form. There is a slight positive relationship between nitrogen content and coal ranking. ?? 2011 Science Press, Institute of Geochemistry, CAS and Springer Berlin Heidelberg.

Chinese Journal of Geochemistry↗
USGS2009

Heavy metal distribution in soils near Palapye, Botswana: An evaluation of the environmental impact of coal mining and combustion on soils in a semi-arid region

Morupule Colliery near Palapye in eastern Botswana is the only coalmine in production in Botswana at present. Its coal is mainly used in the nearby coal-fired Morupule Power Station, which generates approximately 1,000 GWh of electricity per annum. After more than 30 years mining and more than 20 years of combustion, the sedimentation of outlet fly ash from the Morupule Power Station has increased concentrations of Cr, Ni, Zn and As by 13, 2.5, 16 and 5 ppm, respectively, in the fine portion (<53 ??m) of surface soils for approximately 9 km downwind. Elements that have higher concentrations in coal have stronger small-particle association during coal combustion and are less mobile in surface soils, thus showing stronger contaminations in surface soils around the coal-fired plant. Although the degree of contamination of Cr, Ni, Zn and As from coal combustion in the Palapye area at present is low, it is necessary to monitor concentrations of these elements in surface soils routinely in the future. This study also reveals moderate Pb and Zn contaminations in the Palapye area. The former is due to the use of leaded petroleum in motor vehicle traffic and the latter is mainly due to the use of galvanized iron sheets in construction. ?? 2009 Springer Science+Business Media B.V.

Environmental Geochemistry and Health↗
USGS2008

The studying of washing of arsenic and sulfur from coals having different ranges of arsenic contents

To study the effectiveness of washing in removal of arsenic and sulfur from coals with different ranges of arsenic concentration, coal was divided into three groups on the basis of arsenic content: 0-5.5 mg/kg, 5.5 mg/kg-8.00 mg/kg, and over 8.00 mg/kg. The result shows that the arsenic in coals with higher arsenic content occurs mainly in an inorganic state and can be relatively easily removed. Arsenic removal is very difficult and less complete when the arsenic content is lower than 5.5 mg/kg because most of this arsenic is in an organic state. There is no relationship between washing rate of total sulfur and arsenic content, but the relationship between the washing rate of total sulfur and percent of organic sulfur is very strong. ?? 2008 New York Academy of Sciences.

Conference Paper↗
USGS2008

Characterization of Santa Catarina (Brazil) coal with respect to human health and environmental concerns

The current paper presents the concentration, distribution, and modes of occurrence of trace elements of 13 coals from south Brazil. The samples were collected in the state of Santa Catarina. Chemical analyses and the high ash yields indicate that all studied coals are rich in mineral matter, with SiO 2 and Al 2 O 3 dominating as determined by inductively coupled plasma-atomic emission spectrometry (ICP-AES). Quartz is the main mineral species and is associated with minor levels of feldspars, kaolinite, hematite, and iron-rich carbonates. The contents of trace elements, including As, Pb, Cd, Ni, Cr, Mn, Be, V, U, Zn, Li, Cu, Tl, and Ni, in coals were determined. A comparison of ranges and means of elemental concentrations in Santa Catarina, Brazil, and world coals shows that the ranges of most elements in Santa Catarina coal are very close to the usual worldwide concentration ranges in coal. ?? Springer Science+Business Media B.V. 2008.

Environmental Geochemistry and Health↗
USGS2006

Concentration and distribution of sixty-one elements in coals from DPR Korea

Fifty coal samples (28 anthracite and 22 lignites) were collected from both main and small coal mines in DPR Korea prioritized by resource distribution and coal production. The concentrations of 61 elements in 50 coal samples were determined by several multielement and element-specific techniques, including inductively coupled plasma atomic emission spectrometry (ICP-AES), and inductively coupled plasma mass spectrometry (ICP-MS), ion chromatogram (IC), cold-vapor atomic absorption spectrometry (CV-AAS), and hydride generation atomic absorption spectrometry (HGAAS). The ranges, arithmetic means and geometric means of concentrations of these elements are presented. A comparison with crustal abundances (Clarke values) shows that some potentially hazardous elements in the coals of DPR Korea are highly enriched Li, B, S, Cl, Zn, As, Se, Cd, Sn, Sb, W, Te, Hg, Ag, Pb, and La, Ce, Dy, Tm, Ge, Mo, Cs, Tl, Bi, Th and U are moderately enriched. A comparison of ranges and means of elemental concentrations in DPR Korea, Chinese, and world coals shows the ranges of most elements in DPR Korea coals are very close to the ranges of world coals. Arithmetic means of most elements in DPR Korea coals are close to that of American coals. Most elements arithmetic means are higher in Jurassic and Paleogene coals than coals of other ages. In DPR Korea coals, only seven elements in early Permian coals are higher than other periods: Li, Zn, Se, Cd, Hg, Pb, and Bi. Only five elements B, As, Sr, Mo, W in Neogene coals have arithmetic means higher than others. SiO2 and Al2O 3 in ashes are more than 70% except six samples. The correlation between ash yields and major elements from high to low is in the order of Si>Al>Ti>K>Mg>Fe>Na>Ca>P>S. Most elements have high positive correlation with ash (r>0.5) and show high inorganic affinity. ?? 2005 Elsevier Ltd. All rights reserved.

Fuel↗
USGS2005

Endemic arsenosis caused by indoor combustion of high-As coal in Guizhou Province, P.R. China

The arsenic (As) content of coal relating with mineralization of gold in Southwest Guizhou Province, China is up to 35,000 ppm. The coal is burned indoors in open pits for daily cooking and crop drying. As a result, arsenic is precipitated and concentrated in corn (5-20 ppm), chili (100-800 ppm) and other foods. Arsenic concentrations in the drinking water of high-As coal areas are lower than 50 ppb. The estimated main sources of As exposure in this area are from polluted food. Approximately, 3000 arsenosis patients were found by 1998, and more than 100,000 people from six counties were under the threat in China. This paper presents the major ingestion pathway of this type arsenosis and relative geochemistry of high-As coal. ?? Springer 2005.

Environmental Geochemistry and Health↗
USGS2005

Mapping and prediction of Coal Workers' Pneumoconiosis with bioavailable iron content in the bituminous coals

Based on the first National Study of Coal Workers' Pneumoconiosis (CWP) and the U.S. Geological Survey database of coal quality, we show that the prevalence of CWP in seven coal mine regions correlates with levels of bioavailable iron (BAI) in the coals from that particular region (correlation coefficient r = 0.94, p < 0.0015). CWP prevalence is also correlated with contents of pyritic sulfur (r = 0.91, p < 0.0048) or total iron (r = 0.85, p < 0.016) but not with coal rank (r = 0.59, p < 0.16) or silica (r = 0.28, p < 0.54). BAI was calculated using our model, taking into account chemical interactions of pyrite, sulfuric acid, calcite, and total iron. That is, iron present in coals can become bioavailable by pyrite oxidation, which produces ferrous sulfate and sulfuric acid. Calcite is the major component in coals that neutralizes the available acid and inhibits iron's bioavailabiity. Therefore, levels of BAI in the coals are determined by the available amounts of acid after neutralization of calcite and the amount of total iron in the coals. Using the linear fit of CWP prevalence and the calculated BAI in the seven coal mine regions, we have derived and mapped the pneumoconiotic potencies of 7,000 coal samples. Our studies indicate that levels of BAI in the coals may be used to predict coal's toxicity, even before large-scalen mining.

Environmental Health Perspectives↗
USGS2005

Relationship between occurrence mode of arsenic in coal and its washing rate

Based on the analysis of 15 raw coals and washed coals collected from Southwestern, the washing rate of arsenic, sulfur and ash from raw coals was studied. The average washing rate of arsenic in raw coal is 38%. Arsenic of raw coals is mainly associated with pyrite and sulfide. However, arsenic of some raw coals is mainly or wholly associated with organic matter and mineral enwrapped by organic matter. It is difficult to remove such part of arsenic and it will enrich in the washed coals. The results show that there is a little relationship between occurrence mode of arsenic associated with organic sulfur and rank of coal, but it is complicated with age of coal-bearing strata.

Ranliao Huaxue Xuebao/Journal of Fuel Chemistry an↗
USGS2001

Determination of element affinities by density fractionation of bulk coal samples

A review has been made of the various methods of determining major and trace element affinities for different phases, both mineral and organic in coals, citing their various strengths and weaknesses. These include mathematical deconvolution of chemical analyses, direct microanalysis, sequential extraction procedures and density fractionation. A new methodology combining density fractionation with mathematical deconvolution of chemical analyses of whole coals and their density fractions has been evaluated. These coals formed part of the IEA-Coal Research project on the Modes of Occurrence of Trace Elements in Coal. Results were compared to a previously reported sequential extraction methodology and showed good agreement for most elements. For particular elements (Be, Mo, Cu, Se and REEs) in specific coals where disagreement was found, it was concluded that the occurrence of rare trace element bearing phases may account for the discrepancy, and modifications to the general procedure must be made to account for these.

Fuel↗
USGS2001

Crocoite: An unusual mode of occurrence for lead in coal

What is believed to be a very unusual mode of occurrence for lead in coal has been identified as crocoite (PbCrO4). As part of a larger study on trace elements and mineralogy in the Cretaceous Main Seam in New Zealand, crocoite was found in raw coal samples within the lower part of the coal seam. X-ray diffraction (XRD) and bulk chemical data from a SEM equipped with an energy dispersive X-ray analyser (EDXA) have confirmed the identity of this mineral. This is apparently the first time that crocoite has been reported in coal. Crocoite usually occurs only in the oxidised zone of lead mineral deposits. The occurrence of this mineral in the Main Seam coal implies that the deposit was exposed to an oxidising environment at some stage, most likely after coalification. Published by Elsevier Science B.V.

International Journal of Coal Geology↗
USGS2001

Inventario mundial de la calidad del carbon mineral (WoCQI) [The world coal quality inventory (WoCQI)]

Los oficiales encargados de la politica comercial de cada pais requieren informacion clara y precisa sobre el recurso del carbon mineral, particularmente sobre sus propiedades y caracteristicas, para tomar decisiones bien fundamentadas con respecto al mejor uso de los recursos naturales, necesidades de importacion y oportunidades de exportacion, objetivos de politica interna y externa, oportunidades de transferencia tecnologica, posibilidades de inversion externa, estudios ambientales y de salud, y asuntos relacionados con el uso de productos secundarios y su disposicion.

Fact Sheet↗
USGS2000

Direct comparison of XAFS spectroscopy and sequential extraction for arsenic speciation in coal

The speciation of arsenic in an Ohio bituminous coal and a North Dakota lignite has been examined by the complementary methods of arsenic XAFS spectroscopy and sequential extraction by aqueous solutions of ammonium acetate, HCl, HF, and HNO3. In order to facilitate a more direct comparison of the two methods, the arsenic XAFS spectra were obtained from aliquots of the coal prepared after each stage of the leaching procedure. For the aliquots, approximately linear correlations (r2 > 0.98 for the Ohio coal, > 0.90 for the ND lignite) were observed between the height of the edge-step in the XAFS analysis and the concentration of arsenic measured by instrumental neutron activation analysis. Results from the leaching sequence indicate that there are two major arsenic forms present in both coals; one is removed by leaching with HCl and the other by HNO3. Whereas the XAFS spectral signatures of the arsenic leached by HCl are compatible with arsenate for both coals, the arsenic leached by HNO3 is identified as arsenic associated with pyrite for the Ohio coal and as an As3+ species for the North Dakota lignite. Minor arsenate forms persist in both coals after the final leaching with nitric acid. The arsenate forms extracted in HCl are believed to be oxidation products derived from the other major arsenic forms upon exposure of the pulverized coals to air.

ACS Division of Fuel Chemistry, Preprints↗
USGS1999

Intra- and inter-unit variation in fly ash petrography and mercury adsorption: Examples from a western Kentucky power station

Fly ash was collected from eight mechanical and 10 baghouse hoppers at each of the twin 150-MW wall-fired units in a western Kentucky power station. The fuel burned at that time was a blend of many low-sulfur, high-volatile bituminous Central Appalachian coals. The baghouse ash showed less variation between units than the mechanical hoppers. The mechanical fly ash, coarser than the baghouse ash, showed significant differences in the amount of total carbon and in the ratio of isotropic coke to both total carbon and total coke - the latter excluding inertinite and other unburned, uncoked coal. There was no significant variation in proportions of inorganic fly ash constituents. The inter-unit differences in the amount and forms of mechanical fly ash carbon appear to be related to differences in pulverizer efficiency, leading to greater amounts of coarse coal, therefore unburned carbon, in one of the units. Mercury capture is a function of both the total carbon content and the gas temperature at the point of fly ash separation, mercury content increasing with an increase in carbon for a specific collection system. Mercury adsorption on fly ash carbon increases at lower flue-gas temperatures. Baghouse fly ash, collected at a lower temperature than the higher-carbon mechanically separated fly ash, contains a significantly greater amount of Hg.

Energy and Fuels↗
USGS1999

Health impacts of domestic coal use in China

Domestic coal combustion has had profound adverse effects on the health of millions of people worldwide. In China alone several hundred million people commonly burn raw coal in unvented stoves that permeate their homes with high levels of toxic metals and organic compounds. At least 3,000 people in Guizhou Province in southwest China are suffering from severe arsenic poisoning. The primary source of the arsenic appears to be consumption of chili peppers dried over fires fueled with high-arsenic coal. Coal samples in the region were found to contain up to 35,000 ppm arsenic. Chili peppers dried over high-arsenic coal fires adsorb 500 ppm arsenic on average. More than 10 million people in Guizhou Province and surrounding areas suffer from dental and skeletal fluorosis. The excess fluorine is caused by eating corn dried over burning briquettes made from high-fluorine coals and high-fluorine clay binders. Polycyclic aromatic hydrocarbons formed during coal combustion are believed to cause or contribute to the high incidence of esophageal and lung cancers in parts of China. Domestic coal combustion also has caused selenium poisoning and possibly mercury poisoning. Better knowledge of coal quality parameters may help to reduce some of these health problems. For example, information on concentrations and distributions of potentially toxic elements in coal may help delineate areas of a coal deposit to be avoided. Information on the modes of occurrence of these elements and the textural relations of the minerals and macerals in coal may help predict the behavior of the potentially toxic components during coal combustion.

Conference Paper↗
USGS1999

Preliminary study on the mode of occurrence of arsenic in high arsenic coals from southwest Guizhou Province

Coal samples from high arsenic coal areas have been analyzed by electron micropbe analyzer (EMPA), scanning electron microscopy with an energy dispersive X-ray analyzer (SEM-EDX), X-ray diffinction analysis (XRD), low temperature ashing (LTA), transmission electron microscopy (TEM), X-ray absorption fine structure (XAFS), instnunent neutron activation analysis (INAA) and wet chemical analysis. Although some As-bearing minerals such as pyrite, arsenopyrite, realgar (?), As-bearing sulfate, and As-bearing clays are found in the high arsenic coals, their contents do not account for the abundance of arsenic in the some coals. Analysis of the coal indicates that arsenic exists mainly in the form of A s 5+ and A s 3+ , combined with compounds in the organic matrix. The occurrence of such exceptionally high arsenic contents in coal and the fact that the arsenic is dominantly organically associated are unique observations. The modes of occurrence of arsenic in high As-coals are discussed.

Science in China, Series D: Earth Sciences↗
USGS1999

The types of data needed for assessing the environmental and human health impacts of coal

Coal is one of the most important sources of energy. Its worldwide use will continue to expand during the next several decades, particularly in rapidly developing countries such as China and India. Unfortunately, coal use may bring with it environmental and human health costs. Many of the environmental and health problems attributed to coal combustion are due to mobilization of potentially toxic elements. Some of these problems could be minimized or even avoided if comprehensive databases containing appropriate coal quality information were available to decision makers so that informed decisions could be made regarding coal use. Among the coal quality parameters that should be included in these databases are: C, H, N, O, pyritic sulfur, organic sulfur, major, minor, and trace element concentrations, modes of occurrence of environmentally sensitive elements, cleanability, mineralogy, organic chemistry, petrography, and leachability.Coal is one of the most important sources of energy. Its worldwide use will continue to expand during the next several decades, particularly in rapidly developing countries such as China and India. Unfortunately, coal use may bring with it environmental and human health costs. Many of the environmental and health problems attributed to coal combustion are due to mobilization of potentially toxic elements. Some of these problems could be minimized or even avoided if comprehensive databases containing appropriate coal quality information were available to decision makers so that informed decisions could be made regarding coal use. Among the coal quality parameters that should be included in these databases are: C, H, N, O, pyritic sulfur, organic sulfur, major, minor, and trace element concentrations, modes of occurrence of environmentally sensitive elements, cleanability, mineralogy, organic chemistry, petrography, and leachability.

International Journal of Coal Geology↗