Search USGS⌕ Search

Geology topics

Pierre Lacombe

Publications and source records attributed to Pierre Lacombe.

6 recordsLinked to original sources
USGS2017

Bioremediation in fractured rock: 1. Modeling to inform design, monitoring, and expectations

Field characterization of a trichloroethene (TCE) source area in fractured mudstones produced a detailed understanding of the geology, contaminant distribution in fractures and the rock matrix, and hydraulic and transport properties. Groundwater flow and chemical transport modeling that synthesized the field characterization information proved critical for designing bioremediation of the source area. The planned bioremediation involved injecting emulsified vegetable oil and bacteria to enhance the naturally occurring biodegradation of TCE. The flow and transport modeling showed that injection will spread amendments widely over a zone of lower‐permeability fractures, with long residence times expected because of small velocities after injection and sorption of emulsified vegetable oil onto solids. Amendments transported out of this zone will be diluted by groundwater flux from other areas, limiting bioremediation effectiveness downgradient. At nearby pumping wells, further dilution is expected to make bioremediation effects undetectable in the pumped water. The results emphasize that in fracture‐dominated flow regimes, the extent of injected amendments cannot be conceptualized using simple homogeneous models of groundwater flow commonly adopted to design injections in unconsolidated porous media (e.g., radial diverging or dipole flow regimes). Instead, it is important to synthesize site characterization information using a groundwater flow model that includes discrete features representing high‐ and low‐permeability fractures. This type of model accounts for the highly heterogeneous hydraulic conductivity and groundwater fluxes in fractured‐rock aquifers, and facilitates designing injection strategies that target specific volumes of the aquifer and maximize the distribution of amendments over these volumes.

Groundwater↗
USGS2017

Bioremediation in fractured rock: 2. Mobilization of chloroethene compounds from the rock matrix

A mass balance is formulated to evaluate the mobilization of chlorinated ethene compounds (CE) from the rock matrix of a fractured mudstone aquifer under pre- and postbioremediation conditions. The analysis relies on a sparse number of monitoring locations and is constrained by a detailed description of the groundwater flow regime. Groundwater flow modeling developed under the site characterization identified groundwater fluxes to formulate the CE mass balance in the rock volume exposed to the injected remediation amendments. Differences in the CE fluxes into and out of the rock volume identify the total CE mobilized from diffusion, desorption, and nonaqueous phase liquid dissolution under pre- and postinjection conditions. The initial CE mass in the rock matrix prior to remediation is estimated using analyses of CE in rock core. The CE mass mobilized per year under preinjection conditions is small relative to the total CE mass in the rock, indicating that current pump-and-treat and natural attenuation conditions are likely to require hundreds of years to achieve groundwater concentrations that meet regulatory guidelines. The postinjection CE mobilization rate increased by approximately an order of magnitude over the 5 years of monitoring after the amendment injection. This rate is likely to decrease and additional remediation applications over several decades would still be needed to reduce CE mass in the rock matrix to levels where groundwater concentrations in fractures achieve regulatory standards.

New Jersey↗
USGS2015

Imaging pathways in fractured rock using three-dimensional electrical resistivity tomography

Major challenges exist in delineating bedrock fracture zones because these cause abrupt changes in geological and hydrogeological properties over small distances. Borehole observations cannot sufficiently capture heterogeneity in these systems. Geophysical techniques offer the potential to image properties and processes in between boreholes. We used three-dimensional cross borehole electrical resistivity tomography (ERT) in a 9 m (diameter) × 15 m well field to capture high-resolution flow and transport processes in a fractured mudstone contaminated by chlorinated solvents, primarily trichloroethylene. Conductive (sodium bromide) and resistive (deionized water) injections were monitored in seven boreholes. Electrode arrays with isolation packers and fluid sampling ports were designed to enable acquisition of ERT measurements during pulsed tracer injections. Fracture zone locations and hydraulic pathways inferred from hydraulic head drawdown data were compared with electrical conductivity distributions from ERT measurements. Static ERT imaging has limited resolution to decipher individual fractures; however, these images showed alternating conductive and resistive zones, consistent with alternating laminated and massive mudstone units at the site. Tracer evolution and migration was clearly revealed in time-lapse ERT images and supported by in situ borehole vertical apparent conductivity profiles collected during the pulsed tracer test. While water samples provided important local information at the extraction borehole, ERT delineated tracer migration over spatial scales capturing the primary hydrogeological heterogeneity controlling flow and transport. The fate of these tracer injections at this scale could not have been quantified using borehole logging and/or borehole sampling methods alone.

New Jersey↗
USGSDate not supplied

Cross-borehole flow tests and insights into hydraulic connections in fractured mudstone and sandstone

Cross-borehole flow tests provided insights into hydraulic connections in fractured and dipping mudstone and sandstone that were consistent with the lithostratigraphic and structural framework of a VOCcontaminated bedrock research site in west-central New Jersey. Two cross-borehole flow tests were completed. Each test involved measurement and analysis of transient flow in a newly installed deep corehole with a long open interval during short-term pumping and recovery in an adjacent shallow well with a short open interval. The cross-borehole flow test in the mudstone identified a hydraulic connection through a dipping fractured bed between the pumped interval in the well and a flow zone at an intermediate depth in the corehole. The presence of a hydraulic connection between the pumped well and the corehole was not obvious because the water-level response in the corehole was dominated by a shallow zone of high transmissivity, which was hydraulically isolated from the pumped interval. In the sandstone, the cross-borehole flow test identified a hydraulic connection along dipping fractured beds as well as a connection to a deep high-angle fracture that cuts across bedding. These results suggest that application of cross-borehole flow tests at other contaminated fractured-bedrock sites could provide insights into hydraulic connections useful the design and implementation of monitoring and remediation programs.

New Jersey↗