Search USGS⌕ Search

Geology topics

Paul C. Hackley

Publications and source records attributed to Paul C. Hackley.

At least 37 records · Page 2Linked to original sources
USGS2024

Novel insights about petroleum systems from source and reservoir rock characterization, Cretaceous Deposits, Babouri-Figuil Basin, Northern Cameroon

The Babouri-Figuil Basin (BFB) is a frontier basin for petroleum in Cameroon. It belongs to the series of Cretaceous rift basins of the West and Central Rift System (WCARS), the origin of which is related to the opening of the South Atlantic. Within the same rift system, commercial hydrocarbon accumulations have been discovered in Chad, Sudan, Niger and, more recently, in Nigeria (Gongola Basin). The study of the geology of the BFB just recently received considerable attention, mainly because of its presumed hydrocarbon potential. In the pursuit of researching possible petroleum systems in the BFB, the current study provides a first look into the characterization of source and reservoir rock and its integration into a 2D lithostratigraphic model. The study was solely based on outcrop samples. Black shale and massive claystone are good to excellent hydrocarbon source rocks [e.g., up to 38 wt% total organic carbon (TOC), up to 943 mg/g hydrogen index, up to 85 m thickness, up to 20–30 km lateral extension], with moderate to high values of extractable organic matter (e.g., >10,000 ppm). Calcareous claystone, on the other hand, are poor source rocks [e.g., <0.20 wt% TOC]. The samples are thermally immature, except for those located close to volcanic intrusion at Golombe that have reached the threshold for oil generation (Tmax >435 °C, production index >0.1). The petrographic analysis of sandstone revealed that they are fine-grained to coarse-grained, poorly to moderately sorted, texturally and compositionally immature to submature, subarkosic to arkosic arenites. The main diagenetic processes that affected sandstones are as follows: moderate to intense compaction characterized by the development of long, concavo-convex, and sutured contacts between grains; cementation through calcite, iron oxide, and quartz cements; alteration of mica and feldspar grains; partial to complete dissolution of feldspar, mica, amphibole grains, and calcite cement; and the replacement of feldspar and mica grains by clay minerals. Alteration and dissolution increase the porosity of sandstone through the creation of secondary pores. However, mechanical compaction through the development of a pseudomatrix and cementation as pore-filling materials have significantly reduced the quality of sandstone beds as conventional petroleum reservoirs. Hence, the best reservoir-quality sandstones in the basin are generally located in the upper portion of the basin in terms of its lithostratigraphic model. They are the cleanest sandstones with the smallest amount of cement and the lowest ductile grain content (pseudomatrix), with a thickness that varies from 3 m to 120 m and a lateral extension of 20 km. The lithostratigraphic model of the basin is characterized by an extensive lacustrine environment that provided a thick sequence of organic-rich formations; sand deposited as extensive reservoirs sandwiched between shale/claystone beds; the development of stratigraphic traps through lateral facies change; and the widespread deposition of lacustrine and floodplain claystone that provide regional seals. The similarities between the Babouri-Figuil Basin and proven petroleum systems in other WCARS rift basins suggest that the basin may host at least one petroleum system where actively generating source rocks are present.

Babouri-Figuil Basin↗
USGS2024

Structure and morphology of chars and activated carbons obtained from thermal treatment of coal and biomass origin materials, including their wastes: Results from the ICCP Microscopy of Carbon Materials Working Group

This paper describes the evaluation of petrographic textures in char and activated carbon derived from coal, coal by-products and biomass, formed during carbonization and activation processes. This work represents the results of interlaboratory exercises from 2016 to 2022 of the Microscopy of Carbon Materials Working Group in Commission III of the International Committee for Coal and Organic Petrology. The interlaboratory exercises were run on photomicrograph samples. For textural characterization of carbon materials, the existing American Society for Testing and Materials (ASTM) classification system for metallurgical coke was applied. Morphological differences were evaluated in 29 carbon material types, including 22 char samples, and 7 activated carbon (AC) samples obtained experimentally using conventional direct/indirect and microwave heating technologies. This approach gives an extended view on the identification of microporous carbons, and how a certain heat treatment develops a certain optical texture and structure in a raw material. The requested evaluation of carbon materials was related to their porosity, origin, extent, and characteristics, which are particular to each carbon material type. Because carbon matrices can form a wide range of optical textures during heat treatment it is important to demonstrate which carbon occurrences will have a crucial role in industrial applications dominated by adsorption phenomena. The interlaboratory exercises included 17 participants from 14 laboratories. Four sets of digital black and white and colour photomicrographs were distributed, which in total comprised 184 fields of different types of carbon material. The results were evaluated based on four levels: (i) optical texture (isotropic/anisotropic), (ii) optical type and size (punctiform, mosaic, fiber, ribbon, domain), iii) morphology (porous, non-porous/massive), and (iv) particle origin (precursor type). The statistical method applied to evaluate the results was based on “raw agreement indices”. Comparative analyses of the average values of the level of overall agreement showed homogeneity in the results, the mean value was 89%, with a minimum value of 87% and a maximum value of 91% for those who participated in at least three out of four exercises.

International Journal of Coal Geology↗
USGS2024

Decoding paleomire conditions of Paleogene superhigh-organic-sulfur coals

Superhigh-organic‑sulfur (SHOS) coals (coals with organic sulfur content >4 wt%) are unique coal deposits found at a few notable locations in the world. Specific peat accumulation and preservation conditions must be met to form SHOS coals. Organic sulfur is a major constituent of such coals, and it may have various sources depending on the prevailing paleomire conditions. Understanding such paleomire conditions sheds light on the formation mechanisms of SHOS coals. This investigation decodes the paleomire conditions of the Paleogene SHOS coals from Meghalaya, India, using sulfur isotopic compositions ( δ 34 S) of organic sulfur ( δ 34 S OS ) and pyritic sulfur ( δ 34 S Py ) along with organic petrography, pyrite morphology and trace element ratios. Thirty coal samples were collected from the Jaintia Hills in the east, Khasi Hills in the middle, and Garo Hills in the west of Meghalaya. The organic sulfur content in the Garo, Khasi, and Jaintia coals varies from 1.0 to 3.3 wt%, 1.4 to 13.8 wt%, and 1.0 to 7.2 wt%, respectively. Further, after separation from pyritic sulfur and sulfate sulfur phases, the organic sulfur content ranges from 54.4 to 69.2%, 63.8 to 79.9%, and 59.3 to 73.8%, in the Garo, Khasi, and Jaintia Hills, respectively, suggesting the SHOS nature of these coal samples. The δ 34 S Py varies from −29.3 ‰ to +5.7 ‰, −21.3 ‰ to +27.3 ‰, and −12.1 ‰ to −4.3 ‰, in the Jaintia, Khasi, and Garo Hills, respectively, while the δ 34 S OS fluctuates from −4.6 ‰ to +3.7 ‰, −9.3 ‰ to +7.8 ‰, and − 9.0 ‰ to −5.0 ‰, respectively. The δ 34 S values of pyrite and organic sulfur (OS) in Jaintia coals are 34 S depleted compared to seawater sulfate (+22 ‰), leading to fractionations in the range of −51.3 ‰ to −16.3 ‰ (mean − 31.6 ‰) and − 26.6 ‰ to −18.3 ‰ (mean − 23.1 ‰) for pyritic and organic sulfur (OS), respectively. Pyrite in Khasi coals show a relatively heavier δ 34 S composition averaging at −20.5 ‰, whereas organic sulfur (OS) isotope compositions range from −31.3 ‰ to −14.2 ‰ with a mean of −22.6 ‰. Pyrite and OS in the Garo coals are depleted compared to seawater sulfate. Isotope variations in the Jaintia, Khasi, and Garo coals indicate microbial sulfate reduction (MSR) of seawater sulfate. Large isotopic fractionations between Eocene seawater sulfate and pyritic sulfur ( Δ 34 S SO4Eocene – pyrite = up to −51.3 ‰; mean − 31.6 ‰) in Jaintia coals indicate their possible formation in the water column/near the sediment-seawater interface (open system) and also hint toward dissimilatory sulfate reduction pathways that prevailed under anoxic redox conditions. However, mean values of Δ 34 S SO4Eocene – pyrite (−20.5 ‰) in the Khasi coals imply pyrite formation deeper in the sediments (more closed system) under dysoxic conditions. The dominance of OS over pyritic sulfur, framboidal pyrite, and its microcrystal size distributions in Jaintia coals may suggest syngenetic pyrite formation in open water reducing/anoxic conditions under paralic environments. Elevated Sr/Ba and U/Th values in these coals further confirm the anoxic conditions. Nevertheless, the presence of euhedral pyrite with the alleviated pyrite framboids in the Khasi coals and their complete absence in the Garo coals may suggest dysoxic-suboxic and suboxic-oxic depositional conditions, respectively. The isotopic signatures of the Garo coals suggest sulfur contribution from the parent paleobiota and MSR under a freshwater-oxic environment. Insignificant fractionations between δ 34 S Py and δ 34 S OS indicate limited iron and sulfate availability for additional sulfur cycling and disproportionation reactions, typical of oxic conditions. The absence of framboidal pyrite, elevated sulfate concentration, and mean Sr/Ba and U/Th values of 0.5 and 0.3, respectively, further suggest the freshwater peat deposition in the Garo Hills under limnotelmatic to telmatic freshwater conditions. Moreover, high inertinite content (I mmf = 9.77–33.16 vol%), possibly induced by atmospheric peat exposure, supports the interpretation of suboxic-oxic paleomire conditions in Garo Hills. Gradually decreasing mineral matter content from Jaintia (mean 13.6 vol%) to Garo coals (mean 7.4 vol%) additionally projects a transition from mesotrophic brackish to freshwater limnotelmatic environment, complementing the shift in the paleomire condition from eastern (Jaintia) to western (Garo) Meghalayan Hills.

International Journal of Coal Geology↗
USGS2024

The petrology of dispersed organic matter in sedimentary rocks: Review and update

Organic petrology developed from coal petrology, and, in the 1960s, it began to be applied to the study of dispersed organic matter (DOM) in sedimentary rocks other than coal. Over the last few decades, the petrology of DOM has been used to characterize organic matter in sedimentary basins with an emphasis on fossil fuel resource exploration. Today, due to the global research shift on topics related to climate, organic petrology has expanded into new application areas, such as geothermal exploration, biological carbon storage (biochar), disposal, and management of radioactive waste. From the publication of the International Handbook of Coal Petrology (mid-20th century) to the present day, a large number of standards, books, and articles have been published as a result of the work of organic petrographers and petrologists around the world and efforts of the International Committee for Coal and Organic Petrology (ICCP) and The Society for Organic Petrology (TSOP) to promote the study of organic petrology. The current fundamentals and standards of organic petrology provide the international scientific community with well-informed guidance and recommendations to promote in-depth research. However, this information is currently widely scattered, leading to discrepancies in methodology and terminology. Therefore, this paper aims to present a comprehensive review of the main analytical standard test methods and techniques currently used in the petrology of DOM under reflected white light and UV and blue-light excitation, and to provide an efficient and well-defined reference guide. Furthermore, considering the important role of the ICCP in the development of organic petrology since the 1950s, a brief review of the ongoing activities of ICCP dealing with DOM is also presented.

International Journal of Coal Geology↗
USGS2023

Thermal evolution of graptolite and solid bitumen properties at high maturity under natural and artificial conditions

To refine the use of graptolite and solid bitumen as thermal proxies at overmature conditions, we evaluated their evolution via Raman and infrared (IR) spectroscopies, reflectance, and geochemical screening using high-temperature pyrolysis experiments in comparison to naturally matured samples. Naturally matured samples included marine shales from the overmature Upper Ordovician Wufeng-Lower Silurian Longmaxi Formations (herein referred to as Wufeng-Longmaxi) of the Sichuan Basin, China. Immature samples for pyrolysis experiments included Mesoproterozoic (Ectasian) Xiamaling marine shale from Hebei, China (graptolite absent) and graptolite-bearing Ordovician (Tremadocian) Alum marine shale from Grönhögen, Sweden. Pyrolysis experiments at 360 °C for 10 days and 27 days (hydrous conditions), and 450 °C 3 days, 550 °C 3 days, and 550 °C 10 days (all anhydrous) created Xiamaling and Alum residues with solid bitumen and graptolite, respectively, of similar and higher maturity compared to the naturally matured Wufeng-Longmaxi samples. Compositional proxies from IR spectroscopy were inconclusive. Raman spectral properties including Raman band separation (RBS) and the full-width at half-maximum of the G-band (G-FWHM) exhibited robust positive and inverse relationships with increasing reflectance in pyrolysis residues, respectively. RBS values were systematically lower in artificially matured samples versus naturally matured samples with equivalent reflectance values, whereas G-FWHM values were systematically higher. This observation indicates that the limited duration or low internal reactor pressure of pyrolysis experiments is insufficient to allow alignment or ordering of aromatic carbon arrays in both organic matter types, relative to natural maturation occurring at geologic time scales. Reflectance of graptolite was typically higher than co-occurring solid bitumen in Wufeng-Longmaxi samples and the untreated Alum sample, suggesting inherently higher aromaticity. However, aromaticity in pyrolysis residues was systematically higher in solid bitumen compared to graptolite with equivalent reflectance values, indicating a higher kinetic barrier to molecular rearrangement in graptolite versus solid bitumen. These data further clarify differences in the molecular evolution of sedimentary organic matter in natural versus analogue laboratory environments and distinguish the properties of individual organic matter types in response to thermal stress.

International Journal of Coal Geology↗
USGS2023

Interlaboratory study: Testing reproducibility of solid biofuels component identification using reflected light microscopy

Considering global market trends and concerns about climate change and sustainability, increased biomass use for energy is expected to continue. As more diverse materials are being utilized to manufacture solid biomass fuels, it is critical to implement quality assessment methods to analyze these fuels thoroughly. One such method is reflected light microscopy (RLM), which has the potential to complement and enhance current standard testing, leading to improving fuel quality assessment and, ultimately, preventing avoidable air pollution. An interlaboratory study (ILS) was conducted to test the reproducibility of biomass fuels component identification using a reflected light microscopy technique. The exercise was conducted on thirty photomicrographs showing biomass and various undesired components (like plastics or mineral matter), which were purposely added (by the ILS organizers) to contaminate wood pellets and charcoal-based grilling fuels. Forty-six participants had various levels of difficulty identifying the marked components, and as a result, the percentage of correct answers ranged from 52.2 to 94.4%. Among the most difficult components to distinguish were petroleum products and inorganic matter. Various reasons led to the misidentification, including insufficient morphological descriptions of the components provided to participants, ambiguities of the nomenclature, limitations of the analytical and exercise method, and insufficient experience of the participants. Overall, the results indicate that RLM has the potential to enhance the quality assessment of biomass fuels. However, they also demonstrate that the petrographic classification used in this exercise requires further refinement before it can be standardized. While a new simplified classification of solid biomass fuels components was created as an outcome of this study, future research is necessary to refine the nomenclature, develop a microscopic morphological description of the components, and verify the accuracy of component identification with a follow-up ILS.

International Journal of Coal Geology↗
USGS2023

Scanning electron microscopic evaluation of broad ion beam milling effects to sedimentary organic matter: Sputter-induced artifacts or naturally occurring porosity?

Research examining organic-matter hosted porosity has significantly increased during the last decade due to greater focus on understanding hydrocarbon migration and storage in source-rock reservoirs, and technological advances in scanning electron microscopy (SEM) capabilities. The examination of nanometer-scale organic-matter hosted porosity by SEM requires the preparation of exceptionally flat geologic samples beyond the abilities of traditional mechanical polishing, which can deform or otherwise obscure organic surfaces. To meet this demand, broad ion beam (BIB) milling was introduced as a sample preparation technique for SEM petrographic analysis of geologic samples. As with any sample preparation technique, there can be unintended consequences. In this study, we examined the development of nanometer-scale sputter-induced voids caused by BIB milling of thermoset plastic binder material [poly(methyl methacrylate), PMMA] used for the mounting of geologic samples, and artifact sputter-induced voids in the organic matter of Green River Formation and Kimmeridge Clay Formation source rocks. Development of artifact sputter-induced voids was evaluated in relation to variations in the slope of the sample examination surface (0.0–4.9% slope), effectively varying the angle of ion incidence. The results indicate that only minor variations in the angle of ion incidence can generate sputter-induced voids in both PMMA (10.0–386.2 nm diameter sputter-induced voids) and sample sedimentary organic matter (solid bitumen; 12.2–103.6 nm diameter sputter-induced voids). Overall, average artifact pore diameters increased with increasing ion incidence angle within PMMA. Although sputter-induced voids within solid bitumen in the Green River Formation sample were only found in limited extent, the size of these void artifacts falls within the same size range as naturally occurring meso-macroporosity. That is, the pore-like artifacts could easily be misconstrued as naturally developed organic porosity, which is a major concern for SEM-based porosity evaluation methods. This study describes the factors that contribute to the creation of artifact sputter-induced voids, their distinguishing characteristics, and best practices for avoiding the creation of ion-induced artifacts.

International Journal of Coal Geology↗
USGS2023

Evaluation of portable Raman spectroscopic analysis for source-rock thermal maturity assessments on bulk crushed rock

This study presents a simplified method and empirical relationships for determining organic matter thermal maturity using a portable Raman system equipped with a 785 nm laser, for analysis of crushed, whole-rock samples. Suites of rocks represented by shale and coal samples with various mineralogical composition, thermal maturity, and total organic carbon (TOC) were used to test the method and build correlations between Raman band separation (RBS) values and traditional thermal maturity indicators, organic matter reflectance (Ro), and programmed temperature pyrolysis (Tmax) values. A set of disparate shale samples, where both vitrinite and solid bitumen reflectance values were reported, have Ro values that range from 0.40 to 4.62%. Above 3.35% Ro, the corresponding RBS values plateau at ∼290 cm−1, thus correlations were evaluated with a linear regression (R2 = 0.96) between 0.40 and 3.35% Ro. Shale samples with Ro < 2% and Tmax < 551 were also used to correlate Tmax and RBS, yielding a linear correlation with an R2 of 0.94. For the coal data set, Ro values range from 1.21 to 4.08% and correlated RBS values plateau at ∼250 cm−1 above Ro = 3.0%, suggesting its correlative application below this maturity level. Several sample preparation methods were tested on cuttings material and standard deviation values for RBS were minimized by washing, drying, and hand crushing the material to pass through a 40-mesh sieve, although less preparation can still yield reliable results. The high degrees of correlation between whole-rock RBS data and two thermal maturity indicators demonstrate the utility of this approach for generating source rock thermal maturity data from minimally processed, whole-rock samples which could easily be applied in field or laboratory settings.

International Journal of Coal Geology↗
USGS2023

Mapping ancient sedimentary organic matter molecular structure at nanoscales using optical photothermal infrared spectroscopy

Elucidating the molecular structure of sedimentary organic matter (SOM) is key to understanding petroleum generation processes, as well as ancient sedimentary environments. SOM structure is primarily controlled by biogenic source material (e.g., marine vs. terrigenous), depositional conditions, and subsurface thermal history. Additional factors, e.g., strain, may also impact the molecular structure of SOM. Multiple spatially resolved approaches exist for in situ evaluation of SOM, including Raman and infrared spectroscopies, as well as mass spectrometric methods. While these methods have enabled increased understanding of the occurrence and distribution of SOM functional groups, they suffer from disadvantages including low spatial resolution (infrared spectroscopy), limited molecular information (Raman spectroscopy), and sample destruction (mass spectrometric methods). Recent technological advances have resulted in infrared spectrometers capable of breaking the Abbe diffraction limit, greatly increasing the spatial resolutions accessible for an infrared measurement. Here we utilize optical photothermal infrared spectroscopy (O-PTIR) to record maps of functional group distributions at 500 nm spatial resolution in Tasmanites (algal microfossils) from the Upper Devonian Ohio Shale. These data allow for discrimination between Tasmanites , adjacent SOM, and fine-grained minerals. Additionally, functional group distributions within Tasmanites were found to be generally homogenous, although slight variations exist between the body and fold apices (zones of greatest deformation) which may indicate strain-induced chemical reactions. The data presented here represent the first application of O-PTIR to study SOM, highlighting the promise of this analytical approach for future studies evaluating the molecular composition of geologic materials at sub-micron scales.

Organic Geochemistry↗
USGS2022

Characterization of bituminite in Kimmeridge Clay by confocal laser scanning and atomic force microscopy

This work investigates bituminite (amorphous sedimentary organic matter) in Upper Jurassic Kimmeridge Clay source rock via confocal laser scanning microscopy (CLSM) and atomic force microscopy (AFM). These petrographic tools were used to provide better understanding of the nature of bituminite, which has been historically difficult to identify and differentiate from similar organic matter types in source rocks. As part of an International Committee for Coal and Organic Petrology (ICCP) working group, an immature (0.42% vitrinite reflectance), organic-rich (44.1 wt% total organic carbon content) sample of Kimmeridge Clay was distributed to multiple laboratories for CLSM characterization. The primary observations from CLSM imaging and spectroscopy include: 1) the interpreted presence of Botryococcus algae as a contributor to bituminite precursors; 2) color red-shift of sulfide reflectance and bituminite auto-fluorescence from below the sample surface; 3) positive alteration of bituminite from laser-induced photo-oxidation of the sample surface, including fluorescence blue-shift; 4) fluorescence blue-shift associated to higher fluorescence intensity regions in bituminite indicative of compositional (fluorophore) differences; 5) the need for fluorescence spectroscopy standardization as applied via CLSM; and 6) the suitability of CLSM fluorescence spectroscopy to predict solid bitumen reflectance from bituminite spectral emission via calibration to an extant dataset. Secondary CLSM observations include detection of reflected laser light from highly reflective inclusions in bituminite, including sulfides and fusinite, and radiolytic alteration of bituminite caused by substitution of U for Fe in sulfides. Findings from AFM include the observation that surface roughening or surface flattening of bituminite are induced by differential broad ion beam (BIB) milling and are dependent on the location and scale of AFM topology measurement. This result highlights our still limited understanding of the effects of BIB milling on sedimentary organic matter and indicates the need for further research before this technique can be advanced as a standard practice in petrographic sample preparation. Collectively, the results of this study illustrate the general applicability and versatility of AFM and CLSM as tools for organic petrology research, specifically for better understanding of the nature and properties of the bituminite maceral.

Kimmeridge↗
USGS2022

Evaluating aromatization of solid bitumen generated in the presence and absence of water: Implications for solid bitumen reflectance as a thermal proxy

Geological models for petroleum generation suggest thermal conversion of oil-prone sedimentary organic matter in the presence of water promotes increased liquid saturate yield, whereas absence of water causes formation of an aromatic, cross-linked solid bitumen residue. To test the influence of hydrogen from water, organic-rich (22 wt% total organic carbon , TOC) mudrock samples from the Eocene lacustrine Green River Formation Mahogany zone oil shale were pyrolyzed under hydrous and anhydrous conditions in closed system batch reactors at temperatures between 300 and 370 °C for 72 h. Pre- and post-pyrolysis samples were characterized using petrographic approaches including optical microscopy , reflectance, Raman spectroscopy , and scanning electron and transmission electron microscopy to quantify differences in relative appearance, abundance, and composition of solid bitumen newly generated during the pyrolysis experiments. Petrographic analyses were supplemented by geochemical screening measurements (TOC content and programmed temperature pyrolysis). Results show post-hydrous pyrolysis residues contain lower TOC, are comprised of solid bitumen with greater aromaticity , and have textures indicative of lower viscosities, relative to anhydrous residues from the same temperature pyrolysis conditions. These observations suggest solid bitumen forming from thermal conversion of oil-prone sedimentary organic matter under anhydrous conditions may be less aromatic, although more cross-linked, than solid bitumen forming under hydrous conditions at the same time-temperature combination. To explain these results, we suggest that a radical disproportionation mechanism is favored in the presence of hydrogen donated from water, and that this disproportionation promotes aromatization in the solid residue with concomitant expulsion of saturated hydrocarbons.

International Journal of Coal Geology↗
USGS2022

Maturation study of vitrinite in carbonaceous shales and coals: Insights from hydrous pyrolysis

The presence of vitrinite in sedimentary rocks of post-Silurian age allows its reflectance to be used to estimate the thermal maturation of organic matter in petroleum systems. Increasing reflectance of vitrinite, which is primarily driven by aromaticity, depends primarily on the time and temperature attributes of its evolutionary pathway. This study evaluated carbonaceous shales proximal to coal measures and coal samples via isothermal hydrous pyrolysis (HP) to compare differences in the maturation pathways of vitrinite. Sample residues were analysed via vitrinite reflectance (VRo), geochemical screening tests (organic carbon and programmed temperature pyrolysis), and infrared spectroscopy. The study included samples from Indian and North American basins, to observe differences in vitrinite evolution with respect to enclosing mineral matrix, starting degree of aromaticity, organic matter types, stratigraphic age, and depositional environment. The organic content of HP residues shows an intuitive response to the thermal stress of HP, e.g., a general depletion of total organic carbon (TOC) content, pyrolyzate (S2), and hydrogen index with increasing HP temperature. Infrared proxies including C-factor and CH2/CH3 generally decrease with increasing thermal maturity indicating loss of O via CO2 generation and the thermal cracking of aliphatic organic matter. Tmax, production index (PI), and VRo show intuitive increasing values with respect to HP temperature. The least mature sample (0.48 ± 0.05% VRo) generally experienced the maximum change in these parameters during maturation, whereas the most mature sample (0.99 ± 0.06% VRo) generally showed the least change. This observation is consistent with higher kinetic barriers to reaction in more aromatic vitrinite which contains higher bond dissociation energies. Devolatilization of vitrinite during HP causes formation of gas evacuation vacuoles and contraction cracks in the vitrinite grains of both coal and carbonaceous shale. Similarities in vitrinite response to HP between coal and carbonaceous shale suggest that thermal evolution of the vitrinite maceral is principally controlled by inherent rate-limiting kinetic parameters related to its molecular structure. Whereas, the stratigraphic age, sedimentary environment, surrounding organic matter, lithology, and catalysis by mineral composition have less effect. To further improve our understanding of vitrinite aromatization and kinetic parameters, future studies of vitrinite reflectance thermal evolution with temperature should include coal and carbonaceous shale from the same stratigraphic section and extant woody tissue from modern vascular plants.

International Journal of Coal Geology↗
USGS2022

Relating systematic compositional variability to the textural occurrence of solid bitumen in shales

This study presents Raman spectroscopic data paired with scanning electron microscopy (SEM) images to assess solid bitumen composition as a function of solid bitumen texture and association with minerals. A series of hydrous pyrolysis experiments (1–103 days, 300–370 °C) using a low maturity (0.25% solid bitumen reflectance, BR o ), high total organic carbon [(TOC), 14.0 wt%] New Albany Shale sample as the starting material yielded pyrolysis residues designed to evaluate the evolution of solid bitumen aromaticity with increasing temperature and heating duration. Solid bitumen was analyzed by Raman spectroscopy wherein point data were collected from accumulations that ranged in size and degree of association with the mineral matrix. Raman spectroscopy results show that with increasing temperature and experimental duration, solid bitumen aromaticity increases and compositional variability decreases. With regards to texture and composition, coarser-grained solid bitumen (>1.3 μm from nearest mineral grain) has consistently higher, but less variable aromaticity than thinner, wispy solid bitumen which is more intimately associated with the mineral matrix. Collocated scanning electron microscope images were used to provide qualitative assessments of porosity hosted by the organic matter. These paired data sets suggest that solid bitumen porosity development and molecular composition are linked, and these parameters are related to the textural relationships of the organic matter within the whole rock. These results are discussed with perspective towards understanding how rock fabric and texture can influence organic matter evolution during thermal maturation of organic-rich marine shales and inform our broader understanding of these important energy resources.

International Journal of Coal Geology↗
USGS2022

Pore systems and organic petrology of cretaceous Mowry and Niobrara source-rock reservoirs, Powder River Basin, Wyoming, USA

The Powder River Basin (PRB) is a world-class oil province, in large part thanks to contributions from premier source rocks, Cretaceous Mowry and Niobrara shales. Both formations are also unconventional reservoirs. A critical aspect of evaluating production potential and finding sweet spots is the nature of the pore systems in these fine-grained source-rock reservoirs. Variation by stratigraphic interval is important for selecting optimum target zones for horizontal wells. Understanding variation in pore type, size, and connectivity and relationships with mineralogy and fabric help in determining prospectivity in different parts of the basin. Deciphering controls on pore-system development helps predict intervals and locations of optimum reservoir quality. Imaging of Niobrara and Mowry samples from a range of thermal maturities provided observations and data on pore systems, organic matter (OM) types and associations with mineralogy and fabric, wettability, and microporosity associated with both diagenetic and detrital clays. Imaging techniques included scanning electron microscopy, organic petrography and correlative scanning electron microscopy, and mapping of mineralogy through energy dispersive spectroscopy. Mean solid bitumen (BR o ) and vitrinite reflectance (VR o ) values indicate all samples are in the oil window with values ranging from 0.52 to 1.15%. Organic fluorescence is prominent in amorphous OM, solid bitumen and some vitrinite in the early oil window. The fluorescence is extinguished at higher thermal maturity. Carbonate pellets (in Niobrara) mainly contain migrated solid bitumen and residual live oil and little or no terrigenous OM (vitrinite and inertinite). However, terrigenous OM is common in siliceous/argillaceous laminae in both formations, where it occurs with amorphous OM, some of which has converted in situ to a solid bitumen petroleum residue. One key finding is the widespread presence of migrated OM at very early oil window maturity. Distribution of such OM and associated wettability alteration is fabric-controlled, at all levels of thermal maturity studied. Clay morphology and abundance and supporting rigid mineral grain framework strongly influence pore development, preservation, and connectivity in both formations. Carbonate content is a good proxy for reservoir quality in Niobrara intervals due to association of porous solid bitumen with calcareous fecal pellets. High recrystallized microquartz content is associated with the best reservoir intervals in the Mowry.

Wyoming↗
USGS2022

Molecular mechanisms of solid bitumen and vitrinite reflectance suppression explored using hydrous pyrolysis of artificial source rock

The most commonly used parameter for thermal maturity calibration in basin modelling is mean random vitrinite reflectance (R o ). However, R o suppression has been noted in samples containing a high proportion of liptinite macerals. This phenomenon has been demonstrated empirically using hydrous pyrolysis of artificial source rock containing various proportions of thermally immature Wyodak-Anderson coal and liptinite-rich kerogen from the Parachute Creek Member of the Green River Formation. Analysis of samples pyrolyzed at 330 °C for 72 h demonstrates that R o values of both vitrinite and solid bitumen are suppressed in rocks containing liptinite-rich kerogen. Raman and micro-Fourier transform infrared (µ-FTIR) analyses were performed to investigate the mechanisms of suppression. Raman maturity proxies show decreased aromaticity in samples with suppressed R o , particularly in solid bitumen, with aromaticity decreasing as the proportion of liptinite increases. The µ-FTIR proxy for aliphatic chain length and/or branching ratio is static in solid bitumen, yet increases slightly in vitrinite as the liptinite proportion increases. These spectroscopic results suggest slightly different suppression mechanisms for vitrinite and solid bitumen, with reduced C C bond cleavage and marginally reduced aromaticity in vitrinite with suppressed R o , and strongly reduced aromaticity and C C bond cleavage in solid bitumen with suppressed R o . These results support the hypothesis that the generation of free radicals during maturation slows aromatization and highlight the disadvantages of using solid bitumen R o for maturity calibration in liptinite-rich samples. Furthermore, our results indicate that use of Raman data obtained from liptinite-rich samples may also result in suppressed maturity indicators, particularly if the macerals are not identified prior to analysis.

Organic Geochemistry↗
USGS2022

The effect of diagenesis and acetolysis on the preservation of morphology and ultrastructural features of pollen

Pollen morphology on its own and in conjunction with other characteristics has elucidated the origin and evolution of various plant groups. Previous studies of fossil pollen rarely discuss the effects of diagenesis and sample preparation on pollen characteristics, i.e., variability in staining, pollen morphology, and pollen wall ultrastructural characteristics. This paper examines the effect of acetolysis on reflectance and spectral epi-fluorescence measurements. Based on empirical studies, different species under similar experimental conditions display different reflectance values, indicating individual species respond differently to similar post-depositional thermal events. The quantitative pollen fluorescence spectra showed significant variability, but there is an overall increase in the mean wavelength of maximum emission with acetolysis. Increases in these spectral parameters are used to infer thermal maturation and diagenetic pathways in fossil pollen. The paper also discusses observations made on fossil pollen of a known thermal maturity using Pearson's Pollen/Spore Color Standard. Assessment of pollen thermal maturity using this color standard can be an indicator of the quality of morphological and ultrastructural information that can be extracted from fossil pollen. Increasing thermal maturity of pollen may have an effect on staining variability. Based on observations, staining for brightfield or electron microscopy in fossil pollen, although useful for improving contrast in the specimen, must be used with caution when interpreting pollen wall structure. Although single fossil pollen investigations are useful, replication of these studies on similar or the same specimens from the same locality or various localities will collectively provide more information for elucidation of the morphology and ultrastructure of the once living pollen, and is helpful in sorting out characteristics that may be artifacts from post-depositional diagenesis.

Review of Palaeobotany and Palynology↗
USGS2022

Finalization of the Confocal Laser Scanning Microscopy (CLSM) working group

A working group in Commission II to investigate applications of confocal laser scanning microscopy (CLSM) for organic petrology investigations has finalized with publication of the manuscript “Characterization of bituminite in Kimmeridge Clay by confocal laser scanning and atomic force microscopy” in the International Journal of Coal Geology. The manuscript is available via Open Access from https://doi.org/10.1016/j.coal.2022.103927 and also from the Commission II working group (WG) webpage https://www.iccop.org/workinggroup/confocal-laser-scanning-microscopy-clsm/. A report detailing the full history and results from the WG also is available from the Commission II WG webpage. The working group investigated the application of CLSM to an organic-rich (44 wt.% TOC), thermally immature sample (VRo 0.42%) of the Kimmeridge Clay Formation. CLSM imaging and spectroscopy and atomic force microscopy (AFM) were used to characterize bituminite.

ICCP News↗