Search USGS⌕ Search

Geology topics

Neil H. Kenyon

Publications and source records attributed to Neil H. Kenyon.

17 recordsLinked to original sources
USGS2011

GLORIA II sonograph mosaic of the western U.S. Exclusive Economic Zone

In 1983 the United States declared sovereign rights and jurisdiction over living and nonliving resources in an area extending 200 nautical miles (370 km) seaward from its shores. In response to the establishment of this Exclusive Economic Zone (EEZ), the U.S. Geological Survey (USGS) has implemented a program, called EEZ‐Scan, to systematically map the EEZ, using the Geological Long‐ Range Inclined ASDIC (GLORIA) II longrange side scan sonar system developed by the Institute of Oceanographic Sciences (IOS) of Great Britain [Somers et al, 1978]. The first part of the EEZ‐Scan field program was completed in the summer of 1984, when USGS and IOS scientists surveyed the EEZ off the western conterminous United States aboard the British research vessel Farnella (Figure 1). The west coast survey, requiring 96 days of ship time and four separate legs, has resulted in virtually total sonograph coverage of the sea floor from the continental shelf break to the 200‐nautical mile limit between the Mexican and Canadian borders, an area of about 850,000 km 2 . Other data collected on the cruises included two‐channel digital seismic reflection and 3.5‐kHz highresolution and 10‐kHz bathymetric profiles, as well as towed magnetometer data along approximately 20,000 km of trackline spaced nominally at 30‐km intervals.

Western U.S. Exclusive Economic Zone↗
USGS2004

Sedimentary processes of the lower Monterey Fan channel and channel-mouth lobe

The distribution of deposits, sediment transport pathways and processes on the lower Monterey Fan channel and channel-mouth lobe (CML) are studied through the integration of GLORIA and TOBI sidescan sonar data with 7-kHz subbottom profiler records and sediment cores for ground-truthing. The lower Monterey channel is characterised by an up to 30-m-deep channel with poorly developed levees and alternating muddy and silty muddy overbank deposits. The channel is discontinuous, disappearing where gradients are less than about 1:350. Ground-truthing of the large CML shows that the entire CML is characterised by widespread deposits of generally fine sand, with coarser sand at the base of turbidites. Sand is particularly concentrated in finger-like areas of low-backscatter intensity and is interpreted as the result of non-turbulent sediment-gravity flows depositing metres thick massive, fine sand. TOBI sidescan sonar data reveal recent erosional features in the form of scours, secondary channels, large flow slides, and trains of blocks at the distal end of the CML. Erosion is probably related to increasing gradient as the CML approaches Murray Fracture zone and to differential loading of sandy submarine fan deposits onto pelagic clays. Reworking of older flow slides by sediment transport processes on the lobe produces trains of blocks that are several metres in diameter and aligned parallel to the flow direction. ?? 2004 Elsevier B.V. All rights reserved.

Marine Geology↗
USGS1996

Breaching the levee of a channel on the Mississippi Fan

GLORIA images of the youngest channel on the Mississippi Fan indicate that it has not been a stable feature, but instead has shifted its course several times. A detailed study of a site of channel shifting found a complex stratigraphy that resulted from one episode of channel avulsion. The channel avulsion appears to have been initiated by a large mass flow that choked the channel below the point where the levee was breached and additionally spilled a large volume of material through the breach in the levee onto the adjacent fan. Subsequent flows were redirected through this breach in the levee and built a channel-levee complex over the mass movement deposits. A second phase of mass movement resulted from another large mass flow that came down the channel and triggered the collapse of part of the newly developed levee. In this case, locally derived levee sediment was mixed with allochthonous sediment from farther up the fan and was spread northward from the levee. This localized study suggests that fan stratigraphy is complex and variable at several scales, not just at the scale resolved in seismic stratigraphic studies (Weimer 1989) and that large mass flows capable of choking the channel system have been an important mechanism in redirecting sedimentation on the Mississippi Fan.

Mississippi Fan↗
USGS1995

Geometry of sandy deposits at the distal edge of the Mississippi Fan, Gulf of Mexico

Sidescan sonar provides a map of the seafloor that has greatly improved the understanding of depositional processes on modern deep-sea fans (e.g. Mutti and Normark 1991). Here, we present a sidescan-sonar mosaic from the eastern Gulf of Mexico that images the distal reaches of a channel on the Mississippi Fan and the deposits associated with it (Fig. 41.1). This area is one of several deep-sea fan systems that had not previously been imaged by high-resolution sidescan systems. The mosaic highlights the complexity of the spatial relationships of channels and deposits at ends of channels on this large, modern, passive-margin deep-sea fan (Figs 41.2 and 41.3).

Mississippi↗
USGS1993

Map showing sediment isopachs in the deep-sea basins of the Pacific continental margin, Cape Mendocino to Point Conception

The U.S. Geological Survey conducted a series of cruises, EEZSCAN 84 (EEZ-SCAN 84 Scientific Staff, 1986), to collect reconnaissance data on the newly proclaimed Exclusive Economic Zone (EEZ), the area out to 200 nautical miles from the coastline of the United States. The cruises systematically surveyed the entire conterminous United States west coast EEZ using the Geological Long-Range Inclined Asdic (GLORIA) side-scan sonar, a 160-in 3 airgun seismic-reflection profiler, a 3.5-kHz high-resolution seismic-reflection profiler, a 10-kHz echo sounder, and a proton-precession magnetometer. The nominal trackline spacing throughout the survey was 30 km. Derivative maps of sediment thickness (I-2089-A, I-2090-A, I-2091-A) and depth to basement (I-2089-B, I-2090-B, I-2091-B) in the basins of the west coast EEZ were compiled from both the sonar-image dala and the deep-penetration seismic data obtained on these cruises. Only EEZ-SCAN 84 data were used for the map compilations because available data from other cruises in this region are sparsely located, have poor navigational control, or were obtained with seismic systems that were not powerful enough to resolve oceanic basement. For this map series, sediment thickness and depth to basement were determined only in the deep-ocean basin regions because the seismic system used on the EEZ-SCAN 84 cruises could not resolve oceanic basement beneath the thick sediments of the continental slope. All the data used to compile the maps are presented in the "Atlas of the Exclusive Economic Zone, Western Conterminous United States" (EEZ-SCAN 84 Scientific Staff, 1986). Basement Outcrops GLORIA imagery was used to locate areas of basement outcrop throughout the region. Where possible, sediment thickness on and immediately adjacent to basement outcrops was measured from seismic data. Where there was no bathymetric or seismic control, a seamount peak was assumed to have no sediment cover. A pattern is used on the map to indicate all basement outcrops. Data Reduction Acoustic basement in the basins, invariably oceanic Layer 2, was observed on all of the seismic records. One-way traveltime was measured from the sea floor to acoustic basement. Because the trackline spacing of about 30 km is relatively large compared to the data density along track, we chose to measure the sediment thickness every 0.5 hour or at an interval of approximately 7.5 km. Water depth was measured with a 10-kHz profiler. Depth to basement was calculated using the sea surface as the zero datum and adding the corrected water depth (Carter, 1980) to the sediment thickness. Acoustic travel times were converted to depths by first calculating a regression equation from the interval velocity versus depth data of Connard and others (1984). Their data base comprises a compilation of all available Deep Sea Drilling Project data plus wide-angle refraction data, which were collected in Cascadia Basin west of Oregon and represents the best data set available for the United States west coast EEZ. The regression equation was integrated to determine sediment thickness as a function of one-way traveltime . The resulting equation is z = 1400t + 0 .5t 2 where z is sediment thickness in meters, and t is one-way traveltime in seconds. Sediment thicknesses calculated using this equation were compared to values calculated from the general equation of Carlson and others (1986). Values for sediment thickness calculated by the two equations differed by no greater than 10 percent throughout the range of travel times. Bathymetry The bathymetry is from Chase and others (1981). The bathymetric data were compiled from a variety of sources, and data quality is inconsistent. Because of differences in navigational precision and density of coverage, the bathymetric contours of a feature may be at a different location than the corresponding isopleths derived from the EEZ-SCAN 84 data, or a feature may not be indicated on the bathymetry at all. These situations occur because either the feature is poorly located in the bathymetric data set or, especially in the outer EEZ, the bathymetric data are too sparse to have defined the existence of a feature. Acknowledgments Topographic digital data bases were corrected and verified by Christina Lief. Gerald Evenden developed the computer software system MAPGEN, used to compose this map. Reviews, suggestions, and technical contributions from Edward C. Escowitz and Florence Wong and advice about cartographic design from Will Stettner substantially improved the quality of this map. References Cited Carlson, R.L., Gangi, A.F., and Snow, K.R., 1986, Empirical reflection-traveltime/ depth and velocity/depth functions for the deep-sea sediment column: Journal of Geophysical Research, v. 91, no. B8, p. 8249-8266. Carter, D.J.T., 1980, Echo-sounding correction tables: Taunton, United Kingdom, Hydrographic Department, Ministry of Defence, 150 p. Chase, T.E., Wilde, Pat, Normark, W.R, Miller, C.P., Seekins, B.A., and Young, J.D., 1981, Offshore topography of the Western United States between 32° and 49° North latitudes: U.S. Geological Survey Open-File Report 81-443, scale 1:864,518 at 38° latitude, 2 sheets. Connard, G., Couch, R., Keeling , K., Roy, J., and Troseth, S., 1984, Abyssal plain and continental net-objective sedimentary thicknesses, in Kulm, L.D., and others, eds., Western North America continental margin and adjacent ocean floor off Oregon and Washington, Atlas 1 of Regional Atlas Series, Ocean Margin Drilling Program: Woods Hole, Mass., Marine Science International, sheet 7. EEZ-SCAN 84 Scientific Staff, 1986, Atlas of the Exclusive Economic Zone, Western Conterminous United States: U.S. Geological Survey Miscellaneous Investigations Series I-1792, scale 1:500,000, 152 p. See Also "U.S. Pacific West Coast Field Activities" (Paskevich and others, 2011; http://pubs.usgs.gov/of/2010/1332/htmldocs/pc/pc_overview.html). Paskevich, V.F., Wong, F.L., O?Malley, J.J., Stevenson, A.J., and Gutmacher, C.E., 2011, GLORIA sidescan-sonar imagery for parts of the U.S. Exclusive Economic Zone and adjacent areas: U.S. Geological Survey Open-File Report 2010?1332, available at http://pubs.usgs.gov/of/2010/1332/.

IMAP↗
USGS1993

Map showing depth to basement in the deep-sea basins of the Pacific continental margin, Cape Mendocino to Point Conception

The U.S. Geological Survey conducted a series of cruises, EEZSCAN 84 (EEZ-SCAN 84 Scientific Staff, 1986), to collect reconnaissance data on the newly proclaimed Exclusive Economic Zone (EEZ), the area out to 200 nautical miles from the coastline of the United States. The cruises systematically surveyed the entire conterminous United States west coast EEZ using the Geological Long-Range Inclined Asdic (GLORIA) side-scan sonar, a 160-in 3 airgun seismic-reflection profiler, a 3.5-kHz high-resolution seismic-reflection profiler, a 10-kHz echo sounder, and a proton-precession magnetometer. The nominal trackline spacing throughout the survey was 30 km. Derivative maps of sediment thickness (I-2089-A, I-2090-A, I-2091-A) and depth to basement (I-2089-B, I-2090-B, I-2091-B) in the basins of the west coast EEZ were compiled from both the sonar-image dala and the deep-penetration seismic data obtained on these cruises. Only EEZ-SCAN 84 data were used for the map compilations because available data from other cruises in this region are sparsely located, have poor navigational control, or were obtained with seismic systems that were not powerful enough to resolve oceanic basement. For this map series, sediment thickness and depth to basement were determined only in the deep-ocean basin regions because the seismic system used on the EEZ-SCAN 84 cruises could not resolve oceanic basement beneath the thick sediments of the continental slope. All the data used to compile the maps are presented in the "Atlas of the Exclusive Economic Zone, Western Conterminous United States" (EEZ-SCAN 84 Scientific Staff, 1986). Basement Outcrops GLORIA imagery was used to locate areas of basement outcrop throughout the region. Where possible, sediment thickness on and immediately adjacent to basement outcrops was measured from seismic data. Where there was no bathymetric or seismic control, a seamount peak was assumed to have no sediment cover. A pattern is used on the map to indicate all basement outcrops. Data Reduction Acoustic basement in the basins, invariably oceanic Layer 2, was observed on all of the seismic records. One-way traveltime was measured from the sea floor to acoustic basement. Because the trackline spacing of about 30 km is relatively large compared to the data density along track, we chose to measure the sediment thickness every 0.5 hour or at an interval of approximately 7.5 km. Water depth was measured with a 10-kHz profiler. Depth to basement was calculated using the sea surface as the zero datum and adding the corrected water depth (Carter, 1980) to the sediment thickness. Acoustic travel times were converted to depths by first calculating a regression equation from the interval velocity versus depth data of Connard and others (1984). Their data base comprises a compilation of all available Deep Sea Drilling Project data plus wide-angle refraction data, which were collected in Cascadia Basin west of Oregon and represents the best data set available for the United States west coast EEZ. The regression equation was integrated to determine sediment thickness as a function of one-way traveltime . The resulting equation is z = 1400t + 0 .5t 2 where z is sediment thickness in meters, and t is one-way traveltime in seconds. Sediment thicknesses calculated using this equation were compared to values calculated from the general equation of Carlson and others (1986). Values for sediment thickness calculated by the two equations differed by no greater than 10 percent throughout the range of travel times. Bathymetry The bathymetry is from Chase and others (1981). The bathymetric data were compiled from a variety of sources, and data quality is inconsistent. Because of differences in navigational precision and density of coverage, the bathymetric contours of a feature may be at a different location than the corresponding isopleths derived from the EEZ-SCAN 84 data, or a feature may not be indicated on the bathymetry at all. These situations occur because either the feature is poorly located in the bathymetric data set or, especially in the outer EEZ, the bathymetric data are too sparse to have defined the existence of a feature. Acknowledgments Topographic digital data bases were corrected and verified by Christina Lief. Gerald Evenden developed the computer software system MAPGEN, used to compose this map. Reviews, suggestions, and technical contributions from Edward C. Escowitz and Florence Wong and advice about cartographic design from Will Stettner substantially improved the quality of this map. References Cited Carlson, R.L., Gangi, A.F., and Snow, K.R., 1986, Empirical reflection-traveltime/ depth and velocity/depth functions for the deep-sea sediment column: Journal of Geophysical Research, v. 91, no. B8, p. 8249-8266. Carter, D.J.T., 1980, Echo-sounding correction tables: Taunton, United Kingdom, Hydrographic Department, Ministry of Defence, 150 p. Chase, T.E., Wilde, Pat, Normark, W.R, Miller, C.P., Seekins, B.A., and Young, J.D., 1981, Offshore topography of the Western United States between 32° and 49° North latitudes: U.S. Geological Survey Open-File Report 81-443, scale 1:864,518 at 38° latitude, 2 sheets. Connard, G., Couch, R., Keeling , K., Roy, J., and Troseth, S., 1984, Abyssal plain and continental net-objective sedimentary thicknesses, in Kulm, L.D., and others, eds., Western North America continental margin and adjacent ocean floor off Oregon and Washington, Atlas 1 of Regional Atlas Series, Ocean Margin Drilling Program: Woods Hole, Mass., Marine Science International, sheet 7. EEZ-SCAN 84 Scientific Staff, 1986, Atlas of the Exclusive Economic Zone, Western Conterminous United States: U.S. Geological Survey Miscellaneous Investigations Series I-1792, scale 1:500,000, 152 p. See Also "U.S. Pacific West Coast Field Activities" (Paskevich and others, 2011; http://pubs.usgs.gov/of/2010/1332/htmldocs/pc/pc_overview.html). Paskevich, V.F., Wong, F.L., O?Malley, J.J., Stevenson, A.J., and Gutmacher, C.E., 2011, GLORIA sidescan-sonar imagery for parts of the U.S. Exclusive Economic Zone and adjacent areas: U.S. Geological Survey Open-File Report 2010?1332, available at http://pubs.usgs.gov/of/2010/1332/.

IMAP↗
USGS1993

Map showing sediment isopachs in the deep-sea basins of the Pacific Continental Margin, Strait of Juan de Fuca to Cape Mendocino

The U.S. Geological Survey conducted a series of cruises, EEZSCAN 84 (EEZ-SCAN 84 Scientific Staff, 1986), to collect reconnaissance data on the newly proclaimed Exclusive Economic Zone (EEZ), the area out to 200 nautical miles from the coastline of the United States. The cruises systematically surveyed the entire conterminous United States west coast EEZ using the Geological Long-Range Inclined Asdic (GLORIA) side-scan sonar, a 160-in 3 airgun seismic-reflection profiler, a 3.5-kHz high-resolution seismic-reflection profiler, a 10-kHz echo sounder, and a proton-precession magnetometer. The nominal trackline spacing throughout the survey was 30 km. Derivative maps of sediment thickness (I-2089-A, I-2090-A, I-2091-A) and depth to basement (I-2089-B, I-2090-B, I-2091-B) in the basins of the west coast EEZ were compiled from both the sonar-image dala and the deep-penetration seismic data obtained on these cruises. Only EEZ-SCAN 84 data were used for the map compilations because available data from other cruises in this region are sparsely located, have poor navigational control, or were obtained with seismic systems that were not powerful enough to resolve oceanic basement. For this map series, sediment thickness and depth to basement were determined only in the deep-ocean basin regions because the seismic system used on the EEZ-SCAN 84 cruises could not resolve oceanic basement beneath the thick sediments of the continental slope. All the data used to compile the maps are presented in the "Atlas of the Exclusive Economic Zone, Western Conterminous United States" (EEZ-SCAN 84 Scientific Staff, 1986). Basement Outcrops GLORIA imagery was used to locate areas of basement outcrop throughout the region. Where possible, sediment thickness on and immediately adjacent to basement outcrops was measured from seismic data. Where there was no bathymetric or seismic control, a seamount peak was assumed to have no sediment cover. A pattern is used on the map to indicate all basement outcrops. Data Reduction Acoustic basement in the basins, invariably oceanic Layer 2, was observed on all of the seismic records. One-way traveltime was measured from the sea floor to acoustic basement. Because the trackline spacing of about 30 km is relatively large compared to the data density along track, we chose to measure the sediment thickness every 0.5 hour or at an interval of approximately 7.5 km. Water depth was measured with a 10-kHz profiler. Depth to basement was calculated using the sea surface as the zero datum and adding the corrected water depth (Carter, 1980) to the sediment thickness. Acoustic travel times were converted to depths by first calculating a regression equation from the interval velocity versus depth data of Connard and others (1984). Their data base comprises a compilation of all available Deep Sea Drilling Project data plus wide-angle refraction data, which were collected in Cascadia Basin west of Oregon and represents the best data set available for the United States west coast EEZ. The regression equation was integrated to determine sediment thickness as a function of one-way traveltime . The resulting equation is z = 1400t + 0 .5t 2 where z is sediment thickness in meters, and t is one-way traveltime in seconds. Sediment thicknesses calculated using this equation were compared to values calculated from the general equation of Carlson and others (1986). Values for sediment thickness calculated by the two equations differed by no greater than 10 percent throughout the range of travel times. Bathymetry The bathymetry is from Chase and others (1981). The bathymetric data were compiled from a variety of sources, and data quality is inconsistent. Because of differences in navigational precision and density of coverage, the bathymetric contours of a feature may be at a different location than the corresponding isopleths derived from the EEZ-SCAN 84 data, or a feature may not be indicated on the bathymetry at all. These situations occur because either the feature is poorly located in the bathymetric data set or, especially in the outer EEZ, the bathymetric data are too sparse to have defined the existence of a feature. Acknowledgments Topographic digital data bases were corrected and verified by Christina Lief. Gerald Evenden developed the computer software system MAPGEN, used to compose this map. Reviews, suggestions, and technical contributions from Edward C. Escowitz and Florence Wong and advice about cartographic design from Will Stettner substantially improved the quality of this map. References Cited Carlson, R.L., Gangi, A.F., and Snow, K.R., 1986, Empirical reflection-traveltime/ depth and velocity/depth functions for the deep-sea sediment column: Journal of Geophysical Research, v. 91, no. B8, p. 8249-8266. Carter, D.J.T., 1980, Echo-sounding correction tables: Taunton, United Kingdom, Hydrographic Department, Ministry of Defence, 150 p. Chase, T.E., Wilde, Pat, Normark, W.R, Miller, C.P., Seekins, B.A., and Young, J.D., 1981, Offshore topography of the Western United States between 32° and 49° North latitudes: U.S. Geological Survey Open-File Report 81-443, scale 1:864,518 at 38° latitude, 2 sheets. Connard, G., Couch, R., Keeling , K., Roy, J., and Troseth, S., 1984, Abyssal plain and continental net-objective sedimentary thicknesses, in Kulm, L.D., and others, eds., Western North America continental margin and adjacent ocean floor off Oregon and Washington, Atlas 1 of Regional Atlas Series, Ocean Margin Drilling Program: Woods Hole, Mass., Marine Science International, sheet 7. EEZ-SCAN 84 Scientific Staff, 1986, Atlas of the Exclusive Economic Zone, Western Conterminous United States: U.S. Geological Survey Miscellaneous Investigations Series I-1792, scale 1:500,000, 152 p. See Also "U.S. Pacific West Coast Field Activities" (Paskevich and others, 2011; http://pubs.usgs.gov/of/2010/1332/htmldocs/pc/pc_overview.html). Paskevich, V.F., Wong, F.L., O?Malley, J.J., Stevenson, A.J., and Gutmacher, C.E., 2011, GLORIA sidescan-sonar imagery for parts of the U.S. Exclusive Economic Zone and adjacent areas: U.S. Geological Survey Open-File Report 2010?1332, available at http://pubs.usgs.gov/of/2010/1332/.

IMAP↗
USGS1993

Map showing depth to basement in the deep-sea basins of the Pacific continental margin, Strait of Juan de Fuca to Cape Mendocino

The U.S. Geological Survey conducted a series of cruises, EEZSCAN 84 (EEZ-SCAN 84 Scientific Staff, 1986), to collect reconnaissance data on the newly proclaimed Exclusive Economic Zone (EEZ), the area out to 200 nautical miles from the coastline of the United States. The cruises systematically surveyed the entire conterminous United States west coast EEZ using the Geological Long-Range Inclined Asdic (GLORIA) side-scan sonar, a 160-in 3 airgun seismic-reflection profiler, a 3.5-kHz high-resolution seismic-reflection profiler, a 10-kHz echo sounder, and a proton-precession magnetometer. The nominal trackline spacing throughout the survey was 30 km. Derivative maps of sediment thickness (I-2089-A, I-2090-A, I-2091-A) and depth to basement (I-2089-B, I-2090-B, I-2091-B) in the basins of the west coast EEZ were compiled from both the sonar-image dala and the deep-penetration seismic data obtained on these cruises. Only EEZ-SCAN 84 data were used for the map compilations because available data from other cruises in this region are sparsely located, have poor navigational control, or were obtained with seismic systems that were not powerful enough to resolve oceanic basement. For this map series, sediment thickness and depth to basement were determined only in the deep-ocean basin regions because the seismic system used on the EEZ-SCAN 84 cruises could not resolve oceanic basement beneath the thick sediments of the continental slope. All the data used to compile the maps are presented in the "Atlas of the Exclusive Economic Zone, Western Conterminous United States" (EEZ-SCAN 84 Scientific Staff, 1986). Basement Outcrops GLORIA imagery was used to locate areas of basement outcrop throughout the region. Where possible, sediment thickness on and immediately adjacent to basement outcrops was measured from seismic data. Where there was no bathymetric or seismic control, a seamount peak was assumed to have no sediment cover. A pattern is used on the map to indicate all basement outcrops. Data Reduction Acoustic basement in the basins, invariably oceanic Layer 2, was observed on all of the seismic records. One-way traveltime was measured from the sea floor to acoustic basement. Because the trackline spacing of about 30 km is relatively large compared to the data density along track, we chose to measure the sediment thickness every 0.5 hour or at an interval of approximately 7.5 km. Water depth was measured with a 10-kHz profiler. Depth to basement was calculated using the sea surface as the zero datum and adding the corrected water depth (Carter, 1980) to the sediment thickness. Acoustic travel times were converted to depths by first calculating a regression equation from the interval velocity versus depth data of Connard and others (1984). Their data base comprises a compilation of all available Deep Sea Drilling Project data plus wide-angle refraction data, which were collected in Cascadia Basin west of Oregon and represents the best data set available for the United States west coast EEZ. The regression equation was integrated to determine sediment thickness as a function of one-way traveltime . The resulting equation is z = 1400t + 0 .5t 2 where z is sediment thickness in meters, and t is one-way traveltime in seconds. Sediment thicknesses calculated using this equation were compared to values calculated from the general equation of Carlson and others (1986). Values for sediment thickness calculated by the two equations differed by no greater than 10 percent throughout the range of travel times. Bathymetry The bathymetry is from Chase and others (1981). The bathymetric data were compiled from a variety of sources, and data quality is inconsistent. Because of differences in navigational precision and density of coverage, the bathymetric contours of a feature may be at a different location than the corresponding isopleths derived from the EEZ-SCAN 84 data, or a feature may not be indicated on the bathymetry at all. These situations occur because either the feature is poorly located in the bathymetric data set or, especially in the outer EEZ, the bathymetric data are too sparse to have defined the existence of a feature. Acknowledgments Topographic digital data bases were corrected and verified by Christina Lief. Gerald Evenden developed the computer software system MAPGEN, used to compose this map. Reviews, suggestions, and technical contributions from Edward C. Escowitz and Florence Wong and advice about cartographic design from Will Stettner substantially improved the quality of this map. References Cited Carlson, R.L., Gangi, A.F., and Snow, K.R., 1986, Empirical reflection-traveltime/ depth and velocity/depth functions for the deep-sea sediment column: Journal of Geophysical Research, v. 91, no. B8, p. 8249-8266. Carter, D.J.T., 1980, Echo-sounding correction tables: Taunton, United Kingdom, Hydrographic Department, Ministry of Defence, 150 p. Chase, T.E., Wilde, Pat, Normark, W.R, Miller, C.P., Seekins, B.A., and Young, J.D., 1981, Offshore topography of the Western United States between 32° and 49° North latitudes: U.S. Geological Survey Open-File Report 81-443, scale 1:864,518 at 38° latitude, 2 sheets. Connard, G., Couch, R., Keeling , K., Roy, J., and Troseth, S., 1984, Abyssal plain and continental net-objective sedimentary thicknesses, in Kulm, L.D., and others, eds., Western North America continental margin and adjacent ocean floor off Oregon and Washington, Atlas 1 of Regional Atlas Series, Ocean Margin Drilling Program: Woods Hole, Mass., Marine Science International, sheet 7. EEZ-SCAN 84 Scientific Staff, 1986, Atlas of the Exclusive Economic Zone, Western Conterminous United States: U.S. Geological Survey Miscellaneous Investigations Series I-1792, scale 1:500,000, 152 p. See Also "U.S. Pacific West Coast Field Activities" (Paskevich and others, 2011; http://pubs.usgs.gov/of/2010/1332/htmldocs/pc/pc_overview.html). Paskevich, V.F., Wong, F.L., O?Malley, J.J., Stevenson, A.J., and Gutmacher, C.E., 2011, GLORIA sidescan-sonar imagery for parts of the U.S. Exclusive Economic Zone and adjacent areas: U.S. Geological Survey Open-File Report 2010?1332, available at http://pubs.usgs.gov/of/2010/1332/.

IMAP↗
USGS1992

Characteristics of a sandy depositional lobe on the outer Mississippi fan from SeaMARC IA sidescan sonar images

SeaMARC IA sidescan sonar images of the distal reaches of a depositional lobe on the Mississippi Fan show that channelized rather than unconfined transport was the dominant transport mechanism for coarse-grained sediment during the formation of this part of the deep-sea fan. Overbank sheet flow of sands was not an important process in the transport and deposition of the sandy and silty sediment found on this fan. The dendritic distributary pattern and the high order of splaying of the channels, only one of which appears to have been active at a time, suggest that coarse-grained deposits on this fan are laterally discontinuous.

Mississippi↗
USGS1992

Upper Pleistocene turbidite sand beds and chaotic silt beds in the channelized, distal, outer-fan lobes of the Mississippi fan

Cores from a Mississippi outer-fan depositional lobe demonstrate that sublobes at the distal edge contain a complex local network of channelized-turbidite beds of graded sand and debris-flow beds of chaotic silt. Off-lobe basin plains lack siliciclastic coarse-grained beds. The basin-plain mud facies exhibit low acoustic backscatter on SeaMARC IA sidescan sonar images, whereas high acoustic backscatter characteristic of the lobe sand and silt facies. The depth of the first sand-silt layer correlates with relative backscatter intensity and stratigraphic age of the distal sublobes (i.e., shallowest sand = highest backscatter and youngest sublobe). The high proportion (>50%) of chaotic silt compared to graded sand in the distal, outer-fan sublobes may be related to the unstable, muddy, canyon-wall source areas of the extensive Mississippi delta-fed basin slope. A predominace of chaotic silt in cores or outcrops from outer-fan lobes thus may predict similar settings for ancient fans.

Mississippi Fan↗
USGS1992

Map showing sediment isopachs in the deep-sea basins of the Pacific continental margin, Point Conception to Point Loma

The U.S. Geological Survey conducted a series of cruises, EEZSCAN 84 (EEZ-SCAN 84 Scientific Staff, 1986), to collect reconnaissance data on the newly proclaimed Exclusive Economic Zone (EEZ), the area out to 200 nautical miles from the coastline of the United States. The cruises systematically surveyed the entire conterminous United States west coast EEZ using the Geological Long-Range Inclined Asdic (GLORIA) side-scan sonar, a 160-in 3 airgun seismic-reflection profiler, a 3.5-kHz high-resolution seismic-reflection profiler, a 10-kHz echo sounder, and a proton-precession magnetometer. The nominal trackline spacing throughout the survey was 30 km. Derivative maps of sediment thickness (I-2089-A, I-2090-A, I-2091-A) and depth to basement (I-2089-B, I-2090-B, I-2091-B) in the basins of the west coast EEZ were compiled from both the sonar-image dala and the deep-penetration seismic data obtained on these cruises. Only EEZ-SCAN 84 data were used for the map compilations because available data from other cruises in this region are sparsely located, have poor navigational control, or were obtained with seismic systems that were not powerful enough to resolve oceanic basement. For this map series, sediment thickness and depth to basement were determined only in the deep-ocean basin regions because the seismic system used on the EEZ-SCAN 84 cruises could not resolve oceanic basement beneath the thick sediments of the continental slope. All the data used to compile the maps are presented in the "Atlas of the Exclusive Economic Zone, Western Conterminous United States" (EEZ-SCAN 84 Scientific Staff, 1986). Basement Outcrops GLORIA imagery was used to locate areas of basement outcrop throughout the region. Where possible, sediment thickness on and immediately adjacent to basement outcrops was measured from seismic data. Where there was no bathymetric or seismic control, a seamount peak was assumed to have no sediment cover. A pattern is used on the map to indicate all basement outcrops. Data Reduction Acoustic basement in the basins, invariably oceanic Layer 2, was observed on all of the seismic records. One-way traveltime was measured from the sea floor to acoustic basement. Because the trackline spacing of about 30 km is relatively large compared to the data density along track, we chose to measure the sediment thickness every 0.5 hour or at an interval of approximately 7.5 km. Water depth was measured with a 10-kHz profiler. Depth to basement was calculated using the sea surface as the zero datum and adding the corrected water depth (Carter, 1980) to the sediment thickness. Acoustic travel times were converted to depths by first calculating a regression equation from the interval velocity versus depth data of Connard and others (1984). Their data base comprises a compilation of all available Deep Sea Drilling Project data plus wide-angle refraction data, which were collected in Cascadia Basin west of Oregon and represents the best data set available for the United States west coast EEZ. The regression equation was integrated to determine sediment thickness as a function of one-way traveltime . The resulting equation is z = 1400t + 0 .5t 2 where z is sediment thickness in meters, and t is one-way traveltime in seconds. Sediment thicknesses calculated using this equation were compared to values calculated from the general equation of Carlson and others (1986). Values for sediment thickness calculated by the two equations differed by no greater than 10 percent throughout the range of travel times. Bathymetry The bathymetry is from Chase and others (1981). The bathymetric data were compiled from a variety of sources, and data quality is inconsistent. Because of differences in navigational precision and density of coverage, the bathymetric contours of a feature may be at a different location than the corresponding isopleths derived from the EEZ-SCAN 84 data, or a feature may not be indicated on the bathymetry at all. These situations occur because either the feature is poorly located in the bathymetric data set or, especially in the outer EEZ, the bathymetric data are too sparse to have defined the existence of a feature. Acknowledgments Topographic digital data bases were corrected and verified by Christina Lief. Gerald Evenden developed the computer software system MAPGEN, used to compose this map. Reviews, suggestions, and technical contributions from Edward C. Escowitz and Florence Wong and advice about cartographic design from Will Stettner substantially improved the quality of this map. References Cited Carlson, R.L., Gangi, A.F., and Snow, K.R., 1986, Empirical reflection-traveltime/ depth and velocity/depth functions for the deep-sea sediment column: Journal of Geophysical Research, v. 91, no. B8, p. 8249-8266. Carter, D.J.T., 1980, Echo-sounding correction tables: Taunton, United Kingdom, Hydrographic Department, Ministry of Defence, 150 p. Chase, T.E., Wilde, Pat, Normark, W.R, Miller, C.P., Seekins, B.A., and Young, J.D., 1981, Offshore topography of the Western United States between 32° and 49° North latitudes: U.S. Geological Survey Open-File Report 81-443, scale 1:864,518 at 38° latitude, 2 sheets. Connard, G., Couch, R., Keeling , K., Roy, J., and Troseth, S., 1984, Abyssal plain and continental net-objective sedimentary thicknesses, in Kulm, L.D., and others, eds., Western North America continental margin and adjacent ocean floor off Oregon and Washington, Atlas 1 of Regional Atlas Series, Ocean Margin Drilling Program: Woods Hole, Mass., Marine Science International, sheet 7. EEZ-SCAN 84 Scientific Staff, 1986, Atlas of the Exclusive Economic Zone, Western Conterminous United States: U.S. Geological Survey Miscellaneous Investigations Series I-1792, scale 1:500,000, 152 p. index map for I-2089-A See Also "U.S. Pacific West Coast Field Activities" (Paskevich and others, 2011; http://pubs.usgs.gov/of/2010/1332/htmldocs/pc/pc_overview.html). Paskevich, V.F., Wong, F.L., O?Malley, J.J., Stevenson, A.J., and Gutmacher, C.E., 2011, GLORIA sidescan-sonar imagery for parts of the U.S. Exclusive Economic Zone and adjacent areas: U.S. Geological Survey Open-File Report 2010?1332, available at http://pubs.usgs.gov/of/2010/1332/.

IMAP↗
USGS1992

Map showing depth to basement in the deep-sea basins of the Pacific continental margin, Point Conception to Point Loma

The U.S. Geological Survey conducted a series of cruises, EEZSCAN 84 (EEZ-SCAN 84 Scientific Staff, 1986), to collect reconnaissance data on the newly proclaimed Exclusive Economic Zone (EEZ), the area out to 200 nautical miles from the coastline of the United States. The cruises systematically surveyed the entire conterminous United States west coast EEZ using the Geological Long-Range Inclined Asdic (GLORIA) side-scan sonar, a 160-in 3 airgun seismic-reflection profiler, a 3.5-kHz high-resolution seismic-reflection profiler, a 10-kHz echo sounder, and a proton-precession magnetometer. The nominal trackline spacing throughout the survey was 30 km. Derivative maps of sediment thickness (I-2089-A, I-2090-A, I-2091-A) and depth to basement (I-2089-B, I-2090-B, I-2091-B) in the basins of the west coast EEZ were compiled from both the sonar-image dala and the deep-penetration seismic data obtained on these cruises. Only EEZ-SCAN 84 data were used for the map compilations because available data from other cruises in this region are sparsely located, have poor navigational control, or were obtained with seismic systems that were not powerful enough to resolve oceanic basement. For this map series, sediment thickness and depth to basement were determined only in the deep-ocean basin regions because the seismic system used on the EEZ-SCAN 84 cruises could not resolve oceanic basement beneath the thick sediments of the continental slope. All the data used to compile the maps are presented in the "Atlas of the Exclusive Economic Zone, Western Conterminous United States" (EEZ-SCAN 84 Scientific Staff, 1986). Basement Outcrops GLORIA imagery was used to locate areas of basement outcrop throughout the region. Where possible, sediment thickness on and immediately adjacent to basement outcrops was measured from seismic data. Where there was no bathymetric or seismic control, a seamount peak was assumed to have no sediment cover. A pattern is used on the map to indicate all basement outcrops. Data Reduction Acoustic basement in the basins, invariably oceanic Layer 2, was observed on all of the seismic records. One-way traveltime was measured from the sea floor to acoustic basement. Because the trackline spacing of about 30 km is relatively large compared to the data density along track, we chose to measure the sediment thickness every 0.5 hour or at an interval of approximately 7.5 km. Water depth was measured with a 10-kHz profiler. Depth to basement was calculated using the sea surface as the zero datum and adding the corrected water depth (Carter, 1980) to the sediment thickness. Acoustic travel times were converted to depths by first calculating a regression equation from the interval velocity versus depth data of Connard and others (1984). Their data base comprises a compilation of all available Deep Sea Drilling Project data plus wide-angle refraction data, which were collected in Cascadia Basin west of Oregon and represents the best data set available for the United States west coast EEZ. The regression equation was integrated to determine sediment thickness as a function of one-way traveltime . The resulting equation is z = 1400t + 0 .5t 2 where z is sediment thickness in meters, and t is one-way traveltime in seconds. Sediment thicknesses calculated using this equation were compared to values calculated from the general equation of Carlson and others (1986). Values for sediment thickness calculated by the two equations differed by no greater than 10 percent throughout the range of travel times. Bathymetry The bathymetry is from Chase and others (1981). The bathymetric data were compiled from a variety of sources, and data quality is inconsistent. Because of differences in navigational precision and density of coverage, the bathymetric contours of a feature may be at a different location than the corresponding isopleths derived from the EEZ-SCAN 84 data, or a feature may not be indicated on the bathymetry at all. These situations occur because either the feature is poorly located in the bathymetric data set or, especially in the outer EEZ, the bathymetric data are too sparse to have defined the existence of a feature. Acknowledgments Topographic digital data bases were corrected and verified by Christina Lief. Gerald Evenden developed the computer software system MAPGEN, used to compose this map. Reviews, suggestions, and technical contributions from Edward C. Escowitz and Florence Wong and advice about cartographic design from Will Stettner substantially improved the quality of this map. References Cited Carlson, R.L., Gangi, A.F., and Snow, K.R., 1986, Empirical reflection-traveltime/ depth and velocity/depth functions for the deep-sea sediment column: Journal of Geophysical Research, v. 91, no. B8, p. 8249-8266. Carter, D.J.T., 1980, Echo-sounding correction tables: Taunton, United Kingdom, Hydrographic Department, Ministry of Defence, 150 p. Chase, T.E., Wilde, Pat, Normark, W.R, Miller, C.P., Seekins, B.A., and Young, J.D., 1981, Offshore topography of the Western United States between 32° and 49° North latitudes: U.S. Geological Survey Open-File Report 81-443, scale 1:864,518 at 38° latitude, 2 sheets. Connard, G., Couch, R., Keeling , K., Roy, J., and Troseth, S., 1984, Abyssal plain and continental net-objective sedimentary thicknesses, in Kulm, L.D., and others, eds., Western North America continental margin and adjacent ocean floor off Oregon and Washington, Atlas 1 of Regional Atlas Series, Ocean Margin Drilling Program: Woods Hole, Mass., Marine Science International, sheet 7. EEZ-SCAN 84 Scientific Staff, 1986, Atlas of the Exclusive Economic Zone, Western Conterminous United States: U.S. Geological Survey Miscellaneous Investigations Series I-1792, scale 1:500,000, 152 p. index map for I-2089-A See Also "U.S. Pacific West Coast Field Activities" (Paskevich and others, 2011; http://pubs.usgs.gov/of/2010/1332/htmldocs/pc/pc_overview.html). Paskevich, V.F., Wong, F.L., O?Malley, J.J., Stevenson, A.J., and Gutmacher, C.E., 2011, GLORIA sidescan-sonar imagery for parts of the U.S. Exclusive Economic Zone and adjacent areas: U.S. Geological Survey Open-File Report 2010?1332, available at http://pubs.usgs.gov/of/2010/1332/.

IMAP↗
USGS1991

Depositional patterns of the Mississippi Fan surface: Evidence from GLORIA II and high-resolution seismic profiles

GLORIA long-range side-scan sonar imagery and 3.5-kHz seismic-reflection profiles depict a series of nine elongate deposits with generally high-backscatter surfaces covering most of the latest fanlobe sequence of the Mississippi Fan in the eastern Gulf of Mexico. The youngest deposit is a “slump” that covers a 250 by 100 km area of the middle and upper fan. The remaining mapped deposits, termed depositional lobes, are long (as much as 200 km) and relatively thin (less than 35 m thick) bodies. Small channels and lineations on the surface of many of these depositional lobes radiate from a single, larger main channel that is the conduit through which sediment has been supplied to these surficial deposits on the fan. The 3.5-kHz profiles show that adjacent depositional lobes overlap one another rather than interfingering, indicating that only one lobe was an active site of deposition at a time. Shifting of the depositional sites appears to be caused by both aggradation and avulsion. The chronology developed from the overlapping relations indicates the oldest of the mapped depositional lobes are on the lowermost fan, and the youngest are further up the fan. Depositional lobes on the lower fan consist of a series of smaller, elongate features with high-backscatter surfaces (540 km in length) located at the ends of previously unrecognized small channels (< 5 m deep). These small channels extend as much as 120 km from the main channel. Small channelized turbidity currents and/or debris flows, sand flows, or mud flows appear to be the dominant transport process constructing these depositional lobes. Channelized flow is an important mechanism for transporting sediment away from the main channel on this fan and the resulting facies created by these small flows are laterally discontinuous.

Mississippi↗
USGS1989

Sea-floor drainage features of Cascadia Basin and the adjacent continental slope, northeast Pacific Ocean

Sea-floor drainage features of Cascadia Basin and the adjacent continental slope include canyons, primary fan valleys, deep-sea valleys, and remnant valley segments. Long-range sidescan sonographs and associated seismic-reflection profiles indicate that the canyons may originate along a mid-slope escarpment and grow upslope by mass wasting and downslope by valley erosion or aggradation. Most canyons are partly filled with sediment, and Quillayute Canyon is almost completely filled. Under normal growth conditions, the larger canyons connect with primary fan valleys or deep-sea valleys in Cascadia Basin, but development of accretionary ridges blocks or re-routes most canyons, forcing abandonment of the associated valleys in the basin. Astoria Fan has a primary fan valley that connects with Astoria Canyon at the fan apex. The fan valley is bordered by parallel levees on the upper fan but becomes obscure on the lower fan, where a few valley segments appear on the sonographs. Apparently, Nitinat Fan does not presently have a primary fan valley; none of the numerous valleys on the fan connect with a canyon. The Willapa—Cascadia—Vancouver—Juan de Fuca deep-sea valley system bypasses the submarine fans and includes deeply incised valleys to broad shallow swales, as well as within-valley terraces and hanging-valley confluences.

Marine Geology↗
USGS1982

Channel systems and lobe construction in the Mississippi Fan

Morphological features on the Mississippi Fan in the eastern Gulf of Mexico were mapped using GLORIA II, a long-range side-scan sonar system. Prominent is a sinuous channel flanked by well-developed levees and occasional crevasse splays. The channel follows the axis and thickest part of the youngest fan lobe; seismic-reflection profiles offer evidence that its course has remained essentially constant throughout lobe development. Local modification and possible erosion of levees by currents indicates a present state of inactivity. Superficial sliding has affected part of the fan lobe, but does not appear to have been a factor in lobe construction. ?? 1982 A. M. Dowden, Inc.

Geo-Marine Letters↗