Geology topics

Michael J. Stephens

Publications and source records attributed to Michael J. Stephens.

18 recordsLinked to original sources

USGS2026

Hydrogeology, groundwater salinity distributions, and assessment of the effect of oil-production activities on groundwater in the Midway Valley area, western Kern County, San Joaquin Valley, California

This study seeks to determine the effects of oil field produced water disposal operations and well mechanical integrity issues on groundwater quality in oil fields in the southwest San Joaquin Valley, California. Whereas previous studies used groundwater wells to study shallow aquifers outside the oil fields, this study demonstrates that future approaches may use oil well geophysical logs to map groundwater head gradients, create salinity profiles and document changes in salinity over time in oil field areas with sparse groundwater well data and at depths greater than 330 m. We also incorporate an analysis of well histories to determine potential effects of compromised wellbore seals on changes in aquifer quality that cannot be explained by water disposal practices. Water quality in the aquifers is naturally brackish across most of the area, with better quality groundwater occurring in the eastern part. Geophysical logs are used to determine salinity variations within aquifers including the depth at which TDS exceeds 10,000 mg/L. This depth ranges from 366 m in the northwest to approximately 1,500 m in the southeast. Oil well porosity logs are used to determine water table elevations. These logs indicate the water table slopes south-southeast, showing the predominant groundwater flow direction is from oil field disposal areas toward better quality groundwater east of the oil fields. Geophysical logs show formation resistivity near some disposal facilities has decreased over time, indicating the salinity of the aquifer has increased due to disposal of saline produced water in injection wells and ponds. Oil well history analysis suggests that increased salinity over time in water-saturated sand intervals >1.5 km from disposal facilities may be caused by mechanical failures and/or incomplete borehole seals in poorly constructed or abandoned wellbores prevalent throughout the study area—particularly wells drilled prior to 1930.

California↗

USGS2026

Deep groundwater total dissolved solids mapping in the Dakota Group, Williston Basin, USA

Growing concern about the quantity of available freshwater around the world has led to interest in surveying groundwater total dissolved solids (TDS) below water well depths. Deep TDS has not been systematically mapped, and there is much to learn about the distribution and controls on deeper groundwater. In sedimentary basins across the United States, groundwater resources often overlie hydrocarbon resources, providing an opportunity to use borehole geophysical data collected for hydrocarbons to characterize groundwater and pore space resources. This study adapts a recently developed subsurface geostatistical and geophysical modeling approach to continuously map groundwater TDS, porosity, and temperature in the Dakota Group of the Williston Basin—an undercharacterized regional aquifer system overlying deeper hydrocarbon reservoirs. Groundwater TDS in the Dakota Group ranges from approximately 4800 to 26,900 mg/L. TDS patterns are stratified with higher TDS in the lower and upper Dakota Group, and relatively lower TDS in the middle Dakota Group. The lower TDS in the middle zone may represent a preferential regional flow path for lower-TDS meteoric recharge from the west. The alternating pattern of TDS may also be evidence of higher-TDS inflows into the Dakota Group from underlying and potentially from overlying aquifers. Porosity is lower near the center of the Williston Basin and tends to be higher to the east, which may be related to grain size distributions. The new regional TDS and porosity modeling serves as a quantitative reference for water users and provides supporting evidence for hypotheses on Dakota Group recharge.

Montana, North Dakota, South Dakota↗

USGS2026

Groundwater quality near an oil field in a stream-dominated recharge setting, California, USA

Alluvial valley aquifers are important sources of water supply in many areas but effects of co-located oil and gas development on these resources have not been widely reported, especially in settings where recharge is dominated by stream infiltration. Interpreting the presence of geochemical indicators in the context of hydrology, geology, and other factors provides a more complete understanding of the relations between groundwater and sources of oil-field fluids and aids in identifying risks associated with oil and gas development. Groundwater and Salinas River water samples were collected in an alluvial valley near the San Ardo Oil Field in Monterey County, California and analyzed for a wide range of dissolved chemical, gas, and isotopic constituents to determine if oil-field fluids (water and gas from oil-producing and non-producing zones) have mixed with fresh groundwater used for supply. Hydraulic gradients, age-dating tracers, and other geochemical indicators show that recharge from the Salinas River has the potential to dilute oil-field fluids that might migrate or seep into the aquifer. Groundwater and Salinas River water collected downgradient of the San Ardo Oil Field showed little or no evidence of mixing with oil-field fluids. Some samples within the oil field contained trace amounts of hydrocarbons or elevated temperatures, indicating that any potential effects from oil-field activities are minor or have been diluted by recharge from the Salinas River. The two samples with the most geochemical evidence of potential mixing with oil-field fluids (SP-18 and GW-17) were collected west of or along the Los Lobos fault, where naturally occurring hydrocarbons are near the land surface. Those samples are also near active or inactive oil-field wells, and so anthropogenic activities and pathways cannot be ruled out as a cause of trace detections of hydrocarbons and elevated temperatures in the aquifer.

California↗

USGS2025

A joint Gaussian process model of geochemistry, geophysics, and temperature for groundwater TDS in the San Ardo Oil Field, California, USA

Decline in availability of fresh groundwater has expanded interest in brackish groundwater resources; however, the distribution of brackish groundwater is poorly understood. Water resources in sedimentary basins across the United States often overlie oil and gas development. Mapping of groundwater total dissolved solids (TDS) using data from oil well geophysical logs has become an important technique for identifying fresh and brackish groundwater. Existing geophysical log analysis methods use porosity and temperature to relate formation resistivity to TDS. Typically, natural geothermal gradients are used to estimate temperature at the location of collected resistivity. However, in thermally enhanced oil fields, steam is injected into the subsurface to mobilize high viscosity oil, creating variable temperature distributions. Furthermore, TDS derived from resistivity also depends on the fractions of dominant ions. Typically, chloride and bicarbonate fractions must be determined. It is also necessary to model TDS across many geologic units with heterogenous porosity distributions. Collectively, each quantity used to estimate TDS (resistivity, porosity, temperature, bicarbonate fraction) varies in space and time, and available data points are rarely collocated. Here, we present a new method of mapping groundwater TDS that continuously models each quantity together with a joint Gaussian process. This method enables mapping fresh and brackish water with practically available data. We apply this method to the San Ardo Oil Field in Monterey County, California, where steam injection occurs. In some areas of the aquifer system overlying the oil zone, the temperature is ∼75 °C, roughly twice the natural background value. Groundwater TDS is typically <1,500 mg/L in the aquifer and increases with depth to ∼9,000 mg/L in the oil-producing zone. A low-permeability clay layer delineates the fresh and brackish water, likely by inhibiting surface recharge from penetrating the deeper zones, allowing higher-TDS connate water to remain in place. Weaker lateral TDS trends may be controlled by recharge patterns associated with the Salinas River. Our model reveals with high certainty that groundwater has freshened in one localized part of the oil-producing zone and suggests with less certainty that more widespread freshening has also occurred. The lowering of TDS was possibly from decades of low-TDS steam injection and the associated fluid production and disposal operations.

California↗

USGS2025

Relations of groundwater quality to long-term surface disposal of produced water near the Midway-Sunset and Buena Vista Oil Fields, California, USA

Contamination of groundwater by oil-field fluids in proximity to oil and gas development has been an issue of concern to water users and regulators given long histories of development and legacy disposal practices. A robust set of geochemical tracers including petroleum hydrocarbon compounds, thermogenic gases, inorganic ion concentrations, stable isotopes, radioactive isotopes, and noble gases were used to assess if oil-field fluids mixed with groundwater near the Midway-Sunset and Buena Vista Oil Fields in California, USA. Results show evidence of mixing of oil-field fluids with groundwater within the study area from either anthropogenic or natural processes. Produced water plumes associated with modern surface disposal facilities, used since the late 1950s, extend up to 1.5 km and currently remain within the boundaries of the oil fields. Plumes associated with earlier routing of produced water down natural drainages and in large retention structures (Midway Basin and Sunset Basin) near the Buena Vista Lake Bed are present in groundwater east of the oil fields. Based on geochemical tracer evidence, aerial imagery, and aerial electromagnetic surveys, these legacy plumes reach the western portion of the Central Valley aquifer system, an important groundwater resource for agricultural and domestic supply. The legacy plume associated with Sunset Basin may further be detected downgradient in deeper groundwater beneath the southern extent of the Buena Vista Lake Bed based on the presence of thermogenic gases and petroleum hydrocarbon compounds.

California↗

USGS2024

Assessing potential effects of oil and gas development activities on groundwater quality near and overlying the Elk Hills and North Coles Levee Oil Fields, San Joaquin Valley, California

Groundwater resources are utilized near areas of intensive oil and gas development in California’s San Joaquin Valley. In this study, we examined chemical and isotopic data to assess if thermogenic gas or saline water from oil producing formations have mixed with groundwater near the Elk Hills and North Coles Levee Oil Fields in the southwestern San Joaquin Valley. Major ion concentrations and stable isotope compositions were largely consistent with natural processes, including mixing of different recharge sources and water-rock interactions. Trace methane concentrations likely resulted from microbial rather than thermogenic sources. Trace concentrations of benzene and other dissolved hydrocarbons in three wells had uncertain sources that could occur naturally or be derived from oil and gas development activities or other anthropogenic sources. In the mid-1990s, two industrial supply wells had increasing Cl and B concentrations likely explained by mixing with up to 15 percent saline oil-field water injected for disposal in nearby injection disposal wells. Shallow groundwater along the western margin of Buena Vista Lake Bed had elevated Cl, B, and SO 4 concentrations that could be explained by accumulation of salts during natural wetting and drying cycles or, alternatively, legacy surface disposal of saline oil-field water in upgradient ephemeral drainages. This study showed that groundwater had relatively little evidence of thermogenic gas or saline water from oil and gas sources in most parts of the study area. However, the evidence for groundwater mixing with injected disposal water, and possibly legacy surface disposal water, demonstrates produced water management practices as a potential risk factor for groundwater-quality degradation near oil and gas fields. Additional studies in the San Joaquin Valley and elsewhere could improve understanding of such risks by assessing the locations, volumes, and types of produced water disposal practices used during the life of oil fields.

California↗

USGS2024

Land-use interactions, Oil-Field infrastructure, and natural processes control hydrocarbon and arsenic concentrations in groundwater, Poso Creek Oil Field, California, USA

Like many hydrocarbon production areas in the U.S., the Poso Creek Oil Field in California includes and is adjacent to other land uses (agricultural and other developed lands) that affect the hydrology and geochemistry of the aquifer overlying and adjacent to oil development. We hypothesize that the distributions of hydrocarbons and arsenic in groundwater in such areas will be controlled by complex interactions between mixed land uses, oil-field infrastructure, and natural processes. In 2020–2021, samples of groundwater and surface water were collected and analyzed for a large suite of inorganic and organic chemicals and isotope and gas tracers to test this hypothesis. Those data are supplemented with ancillary data on historical geochemistry, hydrology, geology, and oil-field infrastructure. Hydrocarbons in groundwater (e.g., methane through pentane gases and benzene) are associated with natural processes (e.g., fault offsets or transition in sediment depositional environment) and oil-field infrastructure (e.g., fluid-migration pathways associated with uncemented annulus in oil wells or unlined pits). Arsenic concentrations >10 μg per liter (μg/L; maximum concentration 12.9 μg/L) are associated with natural processes in old, high-pH groundwater, and more recent recharge of water from natural and/or engineered recharge processes. Along the southwest margin of the oil field, pumping for drinking-water and irrigation supplies in combination with engineered groundwater recharge produce a depression in groundwater elevations where groundwater with elevated sulfate concentrations from agricultural areas and groundwater with hydrocarbons from the oil field mix to produce a zone of sulfate reduction that removes hydrocarbons and arsenic from groundwater but produces elevated sulfide (S 2- ) concentrations (maximum concentration 29 mg per liter, mg/L). In this study, multiple approaches were required to resolve the overlapping effects of land uses, oil-field infrastructure, and natural processes on the distributions of hydrocarbons and arsenic in groundwater. The combined use of geographic, historical, physical, chemical, isotopic, and other information to constrain processes could be a useful approach for studies in other hydrocarbon-production areas. This is particularly important where land uses affect aquifer hydrology to an extent that causes mixing of groundwaters with different chemical compositions.

California↗

USGS2023

Multiple-well monitoring site within the Poso Creek Oil Field, Kern County, California

Introduction The Poso Creek Oil Field is one of the many fields selected for regional groundwater mapping and monitoring by the California State Water Resources Control Board as part of the Oil and Gas Regional Monitoring Program (RMP; California State Water Resources Control Board, 2015, 2022b; U.S. Geological Survey, 2022a). The U.S. Geological Survey (USGS), in cooperation with the California State Water Resources Control Board, is evaluating several questions about oil and gas development and groundwater resources in California, including (1) the location of groundwater resources; (2) the proximity of oil and gas operations to groundwater and the geologic materials between them; (3) evidence (or no evidence) of fluids from oil and gas sources in groundwater; and (4) the pathways or processes responsible when fluids from oil and gas sources are present in groundwater (U.S. Geological Survey, 2022a). As part of this evaluation, the USGS installed a multiple-well monitoring site within the administrative boundary of the Poso Creek Oil Field about 12 miles north of Bakersfield, California (fig. 1). Data collected at the Poso Creek multiple-well monitoring site (PCCT) provide information about the geology, hydrology, geophysical properties, and water quality of the aquifer system overlying the oil-bearing zone, thus enhancing understanding of relations between adjacent groundwater and the Poso Creek Oil Field in an area where groundwater data are limited, particularly at different depths in the aquifer. This report presents construction information for the PCCT and initial geohydrologic data collected from the site. Similar sites installed on the east side of the Lost Hills Oil Field and North and South Belridge Oil Fields were described by Everett and others (2020a, b).

California↗

USGS2023

Fluid migration pathways to groundwater in mature oil fields: Exploring the roles of water injection/production and oil-well integrity in California, USA

Mature oil fields potentially contain multiple fluid migration pathways toward protected groundwater (total dissolved solids, TDS, in nonexempted aquifer <10,000 mg/L) because of their extensive development histories. Time-series data for water use, fluid pressures, oil-well construction, and geochemistry from the South Belridge and Lost Hills mature oil fields in California are used to explore the roles of injection/production of oil-field water and well-integrity issues in fluid migration. Injection/production of oil-field water modified hydraulic gradients in both oil fields, resulting in chemical transport from deeper groundwater and hydrocarbon-reservoir systems to aquifers in the oil fields. Those aquifers are used for water supply outside the oil-field boundaries. Oil wells drilled before 1976 can be fluid migration pathways because a relatively large percentage of them have >10 m of uncemented annulus that straddles oil-well casing damage and/or the base of groundwater with TDS <10,000 mg/L. The risk of groundwater-quality degradation is higher when wells with those risk factors occur in areas with upward hydraulic gradients created by positive net injection, groundwater withdrawals, or combinations of these variables. The complex changes in hydrologic conditions and groundwater chemistry likely would not have been discovered in the absence of years to decades of monitoring data for groundwater elevations and chemistry, and installation of monitoring wells in areas with overlapping risk factors. Important monitoring concepts based on results from this and other studies include monitoring hydrocarbon-reservoir and groundwater systems at multiple spatiotemporal scales and maintaining transparency and accessibility of data and analyses. This analysis focuses on two California oil fields, but the methods used and processes affecting fluid migration could be relevant in other oil fields where substantial injection/production of oil-field water occurs and oil-well integrity is of concern.

California↗

USGS2022

Geologic controls on groundwater salinity reversal in North Coles Levee Oil Field, southern San Joaquin Valley, California, USA

This paper documents a reversal in the groundwater salinity depth gradient in the North Coles Levee Oil Field in the San Joaquin Valley, California. Salinity, measured in mg/L, was mapped with water quality data from groundwater and oil and gas wells and salinity estimated from oil and gas well borehole geophysical logs using Archie's equation. The resulting three-dimensional salinity volume shows groundwater salinity increasing with depth through the Tulare and San Joaquin Formations to about 50,000 mg/L at 1100 m depth, then decreasing to 10,000–31,000 mg/L in the Etchegoin Formation at 1400 m depth. The high salinity zone occurs near the base of the San Joaquin Formation in sand lenses in shales that have been interpreted as representing a mudflat environment. The groundwater and produced water geochemistry show formation waters lie on the seawater dilution line, indicating the salinity structure is largely the result of dilution or evaporation of seawater and not due to water–rock interactions. Instead, changing depositional environments linked to decreasing sea level may be responsible for variably saline water at or near the time of deposition, leading to a salinity reversal preserved in connate waters. The steepness of the salinity reversal varies laterally, possibly due to post-depositional freshwater recharge allowed by thick sands, alternatively, by a change in connate water composition due to a lateral facies change present at the time of deposition. These results illustrate geologic and paleogeographic processes that drive the vertical salinity structure of groundwater in shallow alluvial basins.

California↗

USGS2022

Airborne electromagnetic survey results near the Poso Creek oil field, San Joaquin Valley, California, fall 2016

An airborne electromagnetic survey west of the Poso Creek oil field, located in the southeastern San Joaquin Valley, California, was flown in October 2016 to improve understanding of the hydrogeologic setting and the distribution of groundwater salinity in the area. The airborne electromagnetic data were used to develop resistivity models of the subsurface, where the mean depth of investigation is about 300 meters below the land surface and thus characterizes parts of the Kern River Formation and overlying sediments. Resistivity models along with water table elevation, historical total dissolved solids measurements of water samples from wells, well lithologic records, borehole geophysical logs, and mapped surface geology were used to develop an understanding of local hydrogeologic controls on resistivity. Interpretation of these data indicate the resistivity structure primarily reflects the general lithologic character and geologic structure of the study area, with more subtle influences from variations in saturation and salinity.

California↗

USGS2022

Mapping aquifer salinity gradients and effects of oil field produced water disposal using geophysical logs: Elk Hills, Buena Vista and Coles Levee Oil Fields, San Joaquin Valley, California

The effects of oil and gas production on adjacent groundwater quality are becoming a concern in many areas of the United States. As a result, it has become increasingly important to identify which aquifers require monitoring and protection. In this study, we map the extent of groundwater with less than 10,000 mg/L TDS both laterally and vertically near the Elk Hills, Buena Vista and Coles Levee Oil Fields in the San Joaquin Valley, California and note evidence of effects of produced water disposal on salinity within the Tulare aquifer. Subsurface maps showing the depth at which groundwater salinity is less than 10,000 mg/L (or Base 10K) in the Tulare aquifer are generated using geophysical logs and verified by comparison to water sample analyses. The depth to Base 10K ranges from 240 m (800 ft) in Elk Hills to 800 m (2650 ft) in the adjacent Buena Vista syncline and is 670 m (2,200 ft) deep in the Coles Levee area to the east. Log-calculated salinities show a relatively smooth increase with depth prior to disposal activities whereas salinities calculated from logs collected near and after disposal activities show a more variable salinity profile with depth. The effect of produced water injection is represented by log resistivity profiles that change from low resistivity at the base of the sand to higher resistivity near the top due to density differences between the saline produced water and the brackish groundwater within each sand. Continued post-disposal logging in new wells in the 18G disposal area on the south flank of Elk Hills shows that injected water has migrated approximately 1,200 m (4,000 ft) downdip (south) over a period of 20 years since the inception of disposal activity.

California↗

USGS2021

Stratigraphic and structural controls on groundwater salinity variations in the Poso Creek Oil Field, Kern County, California, USA

Groundwater total dissolved solids (TDS) distribution was mapped with a three-dimensional (3D) model, and it was found that TDS variability is largely controlled by stratigraphy and geologic structure. General TDS patterns in the San Joaquin Valley of California (USA) are attributed to predominantly connate water composition and large-scale recharge from the adjacent Sierra Nevada. However, in smaller areas, stratigraphy and faulting play an important role in controlling TDS. Here, the relationship of stratigraphy and structure to TDS concentration was examined at Poso Creek Oil Field, Kern County, California. The TDS model was constructed using produced water TDS samples and borehole geophysics. The model was used to predict TDS concentration at discrete locations in 3D space and used a Gaussian process to interpolate TDS over a volume. In the overlying aquifer, TDS is typically <1,000 mg/L and increases with depth to ~1,200–3,500 mg/L in the hydrocarbon zone below the Macoma claystone—a regionally extensive, fine-grained unit—and reaches ~7,000 mg/L in isolated places. The Macoma claystone creates a vertical TDS gradient in the west where it is thickest, but control decreases to the east where it pinches out and allows freshwater recharge. Previously mapped normal faults were found to exhibit inconsistent control on TDS. In one case, high-density faulting appears to prevent recharge from flushing higher-TDS connate water. Elsewhere, the high-throw segments of a normal fault exhibit variable behavior, in places blocking lower-TDS recharge and in other cases allowing flushing. Importantly, faults apparently have differential control on oil and groundwater.

California↗

USGS2021

Groundwater quality of aquifers overlying the Oxnard Oil Field, Ventura County, California

Groundwater samples collected from irrigation, monitoring, and municipal supply wells near the Oxnard Oil Field were analyzed for chemical and isotopic tracers to evaluate if thermogenic gas or water from hydrocarbon-bearing formations have mixed with surrounding groundwater. New and historical data show no evidence of water from hydrocarbon-bearing formations in groundwater overlying the field. However, thermogenic gas mixed with microbial methane was detected in 5 wells at concentrations ranging from 0.011–9.1 mg/L. The presence of these gases at concentrations <10 mg/L do not indicate degraded water quality posing a known health risk. Analysis of carbon isotopes (δ 13 C-CH 4 ) and hydrogen isotopes (δ 2 H-CH 4 ) of methane and ratios of methane to heavier hydrocarbon gases were used to differentiate sources of methane between a) microbial, b) thermogenic or c) mixed sources. Results indicate that microbial-sourced methane is widespread in the study area, and concentrations overlap with those from thermogenic sources. The highest concentrations of thermogenic gas were observed in proximity to relatively high density of oil wells, large injection volumes of water disposal and cyclic steam, shallow oil development, and hydrocarbon shows in sediments overlying the producing oil reservoirs. Depths of water wells containing thermogenic gas were within approximately 200 m of the top of the Vaca Tar Sand production zone (approximately 600 m below land surface). Due to the limited sampling density, the source and pathways of thermogenic gas detected in groundwater could not be conclusively determined. Thermogenic gas detected in the absence of co-occurring water from hydrocarbon-bearing formations may result from natural gas migration over geologic time from the Vaca Tar Sand or deeper formations, hydrocarbon shows in sediments overlying producing zones, and/or gas leaking from oil-field infrastructure. Denser sampling of groundwater, potential end-members, and pressure monitoring could help better distinguish pathways of thermogenic gases.

California↗

USGS2019

A novel method for the extraction, purification and characterization of noble gases in produced fluids

Hydrocarbon systems with declining or viscous oil production are often stimulated using enhanced oil recovery (EOR) techniques, such as the injection of water, steam and CO2, in order to increase oil and gas production. As EOR and other methods of enhancing production such as hydraulic fracturing have become more prevalent, environmental concerns about the impact of both new and historical hydrocarbon production on overlying shallow aquifers have increased. Noble gas isotopes are powerful tracers of subsurface fluid provenance and can be used to understand the impact of EOR on hydrocarbon systems and potentially overlying aquifers. In oil systems, produced fluids can consist of a mixture of oil, water and gas. Noble gases are typically measured in the gas phase; however, it is not always possible to collect gases and therefore produced fluids (which are water, oil and gas mixtures) must be analyzed. We outline a new technique to separate and analyze noble gases in multi-phase hydrocarbon-associated fluid samples. An offline double capillary method has been developed to quantitatively isolate noble gases into a transfer vessel, while effectively removing all water, oil, and less volatile hydrocarbons. The gases are then cleaned and analyzed using standard techniques. Air-saturated water reference materials (n=24) were analyzed and results show a method reproducibility of 2.9% for 4He, 3.8% for 20Ne, 4.5% for 36Ar, 5.3% for 84Kr and 5.7% for 132Xe. This new technique was used to measure the noble gas isotopic compositions in six produced fluid samples from the Fruitvale Oil Field, Bakersfield, California.

Geochemistry, Geophysics, Geosystems↗

USGS2019

Groundwater salinity and the effects of produced water disposal in the Lost Hills-Belridge oilfields, Kern County, California

Increased oil and gas production in many areas has led to concerns over the effects these activities may be having on nearby groundwater quality. In this study we determine the lateral and vertical extent of groundwater with less than 10,000 milligrams per liter (mg/l) total dissolved solids (TDS) near the Lost Hills-Belridge oilfields in northwestern Kern County, California and document evidence of impacts by produced water disposal within the Tulare aquifer and overlying alluvium—the primary protected aquifers in the area. The depth at which groundwater salinity surpasses 10,000 mg/l ranges from 150 m (500 ft [ft]) in the northwestern part of the study area to 490 to 550 m (1,600-1,800 ft) in the south and east respectively as determined by geophysical log analysis and lab analysis of produced water samples. Comparison of logs from replacement wells with logs from their older counterparts shows relatively higher resistivity intervals representing the vadose zone or fresher groundwater being replaced by intervals with much lower resistivity due to infiltration of brines from surface disposal ponds and injection of brines into disposal wells. The effect of the surface ponds is confined to the alluvial aquifer—the underlying Tulare aquifer is largely protected by a regional clay layer at the base of the alluvium. Sand layers affected by injection of produced waters in nearby disposal wells often exhibit log resistivity profiles that change from high resistivity in their upper parts to low resistivity near the base due to stratification by gravity segregation of the denser brines within each affected sand. The effects of produced water injection are mainly evident within the Tulare Formation and can be noted as far as 550 m (1,800 ft) from the main group of disposal wells located along the east flank of South Belridge.

California↗

USGS2018

Groundwater salinity mapping using geophysical log analysis within the Fruitvale and Rosedale Ranch oil fields, Kern County, California, USA

A method is presented for deriving a volume model of groundwater total dissolved solids (TDS) from borehole geophysical and aqueous geochemical measurements. While previous TDS mapping techniques have proved useful in the hydrogeologic setting in which they were developed, they may yield poor results in settings with lithological heterogeneity, complex water chemistry, or limited data. Problems arise because of assumed values for empirical constants in Archie’s Equation, unrealistic porosity and temperature gradients, or bicarbonate-rich groundwater. These issues become critical in complex geologic settings such as the San Joaquin Valley of California, USA. To address this, a method to map TDS in three dimensions is applied to the Fruitvale and Rosedale Ranch oil fields near Bakersfield, California. Borehole resistivity, porosity, and temperature data are used to derive TDS using Archie’s Equation, and are then kriged to interpolate TDS. Archie’s a and m (tortuosity factor and cementation exponent, respectively) are found by comparing model predictions, after kriging, to TDS measurements, and minimizing the differences via mathematical optimization. Contributions of abundant bicarbonate ions to TDS were corrected using an empirical model. This work was motivated by federal and state law requirements to monitor and protect underground sources of drinking water. Modeling shows the legally significant boundary of 10,000 ppm TDS is at ~1,067 m below sea level in Rosedale Ranch, and deepens into Fruitvale to ~1,341 m. Mapping groundwater TDS at this resolution reveals that TDS is primarily controlled by depth, recharge, stratigraphy, and in some places, by faulting and facies changes.

California↗

USGS2018

Tracing enhanced oil recovery signatures in casing gases from the Lost Hills oil field using noble gases

Enhanced oil recovery (EOR) and hydraulic fracturing practices are commonly used methods to improve hydrocarbon extraction efficiency; however the environmental impacts of such practices remain poorly understood. EOR is particularly prevalent in oil fields throughout California where water resources are in high demand and disposal of high volumes of produced water may affect groundwater quality. Consequently, it is essential to better understand the fate of injected (EOR) fluids in California and other subsurface petroleum systems, as well as any potential effect on nearby aquifer systems. Noble gases can be used as tracers to understand hydrocarbon generation, migration, and storage conditions, as well as the relative proportions of oil and water present in the subsurface. In addition, a noble gas signature diagnostic of injected (EOR) fluids can be readily identified. We report noble gas isotope and concentration data in casing gases from oil production wells in the Lost Hills oil field, northwest of Bakersfield, California, and injectate gas data from the Fruitvale oil field, located within the city of Bakersfield. Casing and injectate gas data are used to: 1) establish pristine hydrocarbon noble-gas signatures and the processes controlling noble gas distributions, 2) characterize the noble gas signature of injectate fluids, 3) trace injectate fluids in the subsurface, and 4) construct a model to estimate EOR efficiency. Noble gas results range from pristine to significantly modified by EOR, and can be best explained using a solubility exchange model between oil and connate/formation fluids, followed by gas exsolution upon production. This model is sensitive to oil-water interaction during hydrocarbon expulsion, migration, and storage at reservoir conditions, as well as any subsequent modification by EOR.

California↗