Geology topics

Michael J. Andersen

Publications and source records attributed to Michael J. Andersen.

5 recordsLinked to original sources

USGS2016

Sediment loads and transport at constructed chutes along the Missouri River - Upper Hamburg Chute near Nebraska City, Nebraska, and Kansas Chute near Peru, Nebraska

The U.S. Geological Survey, in cooperation with the U.S. Army Corps of Engineers, monitored suspended sediment within constructed Missouri River chutes during March through October 2012. Chutes were constructed at selected river bends by the U.S. Army Corps of Engineers to help mitigate aquatic habitat lost through the creation and maintenance of the navigation channel on the Missouri River. The restoration and development of chutes is one method for creating shallow-water habitat within the Missouri River to meet requirements established by the amended 2000 Biological Opinion. Understanding geomorphic channel-evolution processes and sediment transport is important for the design of chutes, monitoring and maintenance of existing chutes, and characterizing the habitat that the chutes provide. This report describes the methods used to monitor suspended sediment at two Missouri River chutes and presents the results of the data analysis to help understand the suspended-sediment characteristics of each chute and the effect the chutes have on the Missouri River. Upper Hamburg chute, near Nebraska City, Nebraska, and Kansas chute, near Peru, Nebraska, were selected for monitoring. At each study site, monthly discrete samples were collected from April through October in the Missouri River main-channel transects upstream from the chute inlet, downstream from the chute outlet, at the outlet (downstream transect) of both chutes, and at the inlet (upstream transect) of Kansas chute. In addition, grab samples from all chute sampling locations were collected using autosamplers. Suspended-sediment concentration (SSC) and grain-size metrics were determined for all samples (discrete and grab). Continuous water-quality monitors recorded turbidity and water temperature at 15-minute intervals at the three chute sampling locations. Two acoustic Doppler velocimeters, one within each chute, measured water depth and current velocities continuously. The depth and velocity data were used to estimate streamflow within each chute. The sampling design was developed to understand the suspended-sediment differences within each chute and between the chute and the Missouri River main channel during discrete sampling. The sampling design also allowed for site-specific surrogate relations between SSC and turbidity to be developed, which could be used to compute real-time estimates of SSC and sediment loads within the chutes. Real-time estimates of SSC and sediment loads enable a better understanding of sediment transport within the chutes during times when physical samples are not collected, including periods of high flow. High flows during the summer of 2011 resulted in substantial alterations to both studied chutes; therefore, the U.S. Army Corps of Engineers repaired and modified both chutes during 2012. These unforeseen repairs and modifications within the chutes added uncertainty to the analysis because concentrations were altered by construction equipment and flow alteration. Daily suspended-sediment and suspended-silt loads were estimated based on surrogate relations with turbidity. A linear regression was used to estimate equal-width increment (EWI)-equivalent SSC from autosampler SSC before using the model-calibration dataset to determine the best-fit model for prediction of SSC from the turbidity and, in some cases, discharge. Correlation between suspended-sand concentration ( SSandC ) in EWI samples and concurrent samples collected by an autosampler was low; therefore, SSandC was excluded from development of surrogate relations because a large part of the calibration dataset was from autosamples. Instead, SSandC was estimated as SSC minus suspended-silt-clay concentration ( SSiltC ). At all sites, the best-fit models included the base-10 logarithm of concentration and turbidity, and at Kansas chute upstream, the base-10 logarithm of streamflow was also included in the best-fit models. These surrogate models were used to estimate continuous time series of SSC and SSiltC . Estimated concentrations of suspended sediment were used to estimate instantaneous and daily loads for total suspended sediment, suspended silt-clay, and suspended sand. Estimated daily suspended-sediment loads were not significantly different between upstream and downstream transects within the Kansas chute, and most individual daily loads within the chute were not significantly different between upstream and downstream transects when evaluated using overlap in daily 95-percent confidence intervals. The comparison of daily load values for upstream and downstream chute transects, as estimated from turbidity-based surrogate models for Kansas chute, documents the daily dynamic nature of sediment transport within the chute with a temporal resolution that is not practical with discrete suspended-sediment sampling alone. Comparisons of concentrations and loads from EWI samples collected from different transects within a study site resulted in few significant differences, but comparisons are limited by small sample sizes and large within-transect variability. When comparing the Missouri River upstream transect to the chute inlet transect, similar results were determined in 2012 as were determined in 2008—the chute inlet affected the amount of sediment entering the chute from the main channel. In addition, the Kansas chute is potentially affecting the sediment concentration within the Missouri River main channel, but small sample size and construction activities within the chute limit the ability to fully understand either the effect of the chute in 2012 or the effect of the chute on the main channel during a year without construction. Finally, some differences in SSC were detected between the Missouri River upstream transects and the chute downstream transects; however, the effect of the chutes on the Missouri River main-channel sediment transport was difficult to isolate because of construction activities and sampling variability.

Nebraska↗

USGS2010

Quantifying canal leakage rates using a mass-balance approach and heat-based hydraulic conductivity estimates in selected irrigation canals, western Nebraska, 2007 through 2009

The water supply in areas of the North Platte River Basin in the Nebraska Panhandle has been designated as fully appropriated or overappropriated by the Nebraska Department of Natural Resources (NDNR). Enacted legislation (Legislative Bill 962) requires the North Platte Natural Resources District (NPNRD) and the NDNR to develop an Integrated Management Plan (IMP) to balance groundwater and surface-water supply and demand in the NPNRD. A clear understanding of the groundwater and surface-water systems is critical for the development of a successful IMP. The primary source of groundwater recharge in parts of the NPNRD is from irrigation canal leakage. Because canal leakage constitutes a large part of the hydrologic budget, spatially distributing canal leakage to the groundwater system is important to any management strategy. Surface geophysical data collected along selected reaches of irrigation canals has allowed for the spatial distribution of leakage on a relative basis; however, the actual magnitude of leakage remains poorly defined. To address this need, the U.S. Geological Survey, in cooperation with the NPNRD, established streamflow-gaging stations at upstream and downstream ends from two selected canal reaches to allow a mass-balance approach to be used to calculate daily leakage rates. Water-level and sediment temperature data were collected and simulated at three temperature monitoring sites to allow the use of heat as a tracer to estimate the hydraulic conductivity of canal bed sediment. Canal-leakage rates were estimated by applying Darcy's Law to modeled vertical hydraulic conductivity and either the estimated or measured hydraulic gradient. This approach will improve the understanding of the spatial and temporal variability of canal leakage in varying geologic settings identified in capacitively coupled resistivity surveys. The high-leakage potential study reach of the Tri-State Canal had two streamflow-gaging stations and two temperature monitoring sites along its length. Calculated leakage rates from the mass-balance approach varied from year to year and were generally dependent on local climatic conditions, and the timing and magnitude of the initial seasonal diversion into the Tri-State Canal. Leakage rates ranged from 0.98 meter per day (m/d) on June 22, 2007, to about to 0 m/d during July 2009. Drier conditions generally resulted in higher leakage rates because of reduced flow from Spottedtail Creek, lower groundwater levels near Spottedtail Creek, and no unmeasured flow entering the reach. Of the three years studied (2007-09), 2007 was the driest, and therefore had the highest canal leakage rates. The moderately low leakage potential study reach of Interstate Canal had two streamflow-gaging stations and one temperature monitoring site along its length. Excluding the leakage calculations from early May 2007, leakage rates ranged from 0.08 to 0.7 m/d. Less variability in leakage from year to year indicates that climatic conditions may have less of an effect for Interstate Canal compared to Tri-State Canal. This may be because Interstate Canal was cut into the northern edge of the North Platte alluvial valley and consequently the canal bed is well above the local groundwater table resulting in a constant (1 meter per meter [m/m]) hydraulic gradient. Interstate Canal also does not receive any captured flow that can vary substantially year to year. Two temperature monitoring sites were installed within the high-leakage potential reach of Tri-State Canal. Site TCTEMP1 was established in 2007 where the water table was well below the canal bed surface. The vertical hydraulic conductivity of the poorly sorted sand and gravel beneath site TCTEMP1 was estimated using a calibrated one-dimensional VS2DH model. Using a trial-and-error approach, the best-fit vertical hydraulic conductivity for the site TCTEMP1 model domain was 1.1 m/d. Site TCTEMP2 was established at the mouth of Spottedtail Creek where a shallow

Scientific Investigations Report↗

USGS2008

Hydrographic Surveys for Six Water Bodies in Eastern Nebraska, 2005-07

The U.S. Geological Survey, in cooperation with the Nebraska Department of Environmental Quality, completed hydrographic surveys for six water bodies in eastern Nebraska: Maskenthine Wetland, Olive Creek Lake, Standing Bear Lake, Wagon Train Lake and Wetland, Wildwood Lake, and Yankee Hill Lake and sediment basin. The bathymetric data were collected using a boat-mounted survey-grade fathometer that operated at 200 kHz, and a differentially corrected Global Positioning System with antenna mounted directly above the echo-sounder transducer. Shallow-water and terrestrial areas were surveyed using a Real-Time Kinematic Global Positioning System. The bathymetric, shallow-water, and terrestrial data were processed in a geographic information system to generate a triangulated irregular network representation of the bottom of the water body. Bathymetric contours were interpolated from the triangulated irregular network data using a 2-foot contour interval. Bathymetric contours at the conservation pool elevation for Maskenthine Wetland, Yankee Hill Lake, and Yankee Hill sediment pond also were interpolated in addition to the 2-foot contours. The surface area and storage capacity of each lake or wetland were calculated for 1-foot intervals of water surface elevation and are tabulated in the Appendix for all water bodies.

Scientific Investigations Report↗

USGS2007

Data collected to support monitoring of constructed emergent sandbar habitat on the Missouri River downstream from Gavins Point Dam, South Dakota and Nebraska, 2004-06

The U.S. Army Corps of Engineers has constructed emergent sandbar habitat on sections of the Missouri River bordering South Dakota and Nebraska downstream from Gavins Point Dam to create and enhance habitat for threatened and endangered bird species. Two areas near river miles 761.3 and 769.8 were selected for construction of emergent sandbar habitat. Pre- and postconstruction data were collected by the U.S. Geological Survey, in cooperation with the U.S. Army Corps of Engineers, to evaluate the success of the habitat management techniques. Data collected include pre- and postconstruction channel-geometry data (bathymetric and topographic) for areas upstream from, downstream from, and within each construction site. Water-velocity data were collected for selected parts of the site near river mile 769.8. Instruments and methods used in data collection, as well as quality-assurance and quality-control measures, are described. Geospatial channel-geometry data are presented for transects of the river channel as cross sections and as geographical information system shapefiles. Geospatial land-surface elevation data are provided for part of each site in the form of a color-shaded relief map. Geospatial water-velocity data also are provided as color-shaded maps and geographical information system shapefiles.

Nebraska, South Dakota↗

USGS2006

Determination of canal leakage potential using continuous resistivity profiling techniques, Interstate and Tri-State Canals, western Nebraska and eastern Wyoming, 2004

In the North Platte River Basin, a ground-water model is being developed to evaluate the effectiveness of using water leakage from selected irrigation canal systems to enhance ground-water recharge. The U.S. Geological Survey, in cooperation with the North Platte Natural Resources District, used land-based capacitively coupled and water-borne direct-current continuous resistivity profiling techniques to map the lithology of the upper 8 meters and to interpret the relative canal leakage potential of 110 kilometers of the Interstate and Tri-State Canals in western Nebraska and eastern Wyoming. Lithologic descriptions from 25 test holes were used to evaluate the effectiveness of both techniques for indicating relative grain size. An interpretive color scale was developed that symbolizes contrasting resistivity features indicative of different grain-size categories. The color scale was applied to the vertically averaged resistivity and used to classify areas of the canals as having either high, moderate, or low canal leakage potential. When results were compared with the lithologic descriptions, both land-based and water-borne continuous resistivity profiling techniques were determined to be effective at differentiating coarse-grained from fine-grained sediment. Both techniques were useful for producing independent, similar interpretations of canal leakage potential.

Nebraska, Wyoming↗