Geology topics

Kiyofumi Suzuki

Publications and source records attributed to Kiyofumi Suzuki.

7 recordsLinked to original sources

USGS2022

Scientific results of the Hydrate-01 Stratigraphic Test Well Program, Western Prudhoe Bay Unit, Alaska North Slope

The United States Department of Energy, the MH21-S Research Consortium of Japan, and the United States Geological Survey are collaborating to enable gas hydrate scientific drilling and extended-duration reservoir response testing on the Alaska North Slope. To feasibly execute such a test, a location is required that is accessible from existing roads and gravel pads and that can be occupied without disrupting ongoing industry operations. A review of potential locations meeting these criteria determined the likely occurrence of gas hydrate in two fine-grained marginal-marine sands of Tertiary age in the vicinity of the inactive “Kuparuk State 7-11-12” exploration pad in the western Prudhoe Bay Unit (PBU). Existing well and seismic data for that site were insufficient to preclude the potential for free gas occurrence within the deeper (and most prospective) target sand. Therefore, with support from the PBU Working Interest Owners, Alaska Department of Natural Resources, and Petrotechnical Resources Alaska, the Hydrate-01 Stratigraphic Test Well (STW) was drilled in December 2018 to confirm the suitability of the site for future gas hydrate scientific testing. The Hydrate-01 well was successfully drilled to −3290 ft (1003 m) subsea vertical depth at a bottom hole location of approximately 900 ft (∼275 m) east of the surface location. The drilling program featured acquisition of a full suite of logging while drilling data, the collection of side-wall pressure cores, and the installation of distributed temperature and distributed acoustic sensor fiber-optic cables. The log data acquired confirmed the occurrence of gas hydrate at high saturation in two target sands. Integrated evaluation of log and sidewall core data provide petrophysical and geomechanical property information that allow for potential reservoir response to depressurization to be simulated. The deeper “B1 sand” is deemed to be most favorable for reservoir response testing as a result of confirmed gas hydrate occurrence in sediments of high intrinsic permeability, location within 100 ft (30 m) of the base of gas hydrate stability, and minimal risk for direct communication with permeable water-bearing (hydrate-free) zones. The shallower “D1 sand” provides a secondary target that is differentiated by colder in situ temperatures and the interpreted direct hydraulic communication to a lower section of non-hydrate-bearing, water-saturated sand. The Hydrate-01 log data also confirm the occurrence of at least one sub-seismic fault in close proximity to the B1 sand reservoir. To better image the distribution of the gas-hydrate-bearing reservoir sections and associated faults, a three-dimensional (3D) vertical seismic profile was conducted in early 2019 using the distributed acoustic sensors installed as part of the Hydrate-01 STW completion. Detailed two-dimensional (2D) and 3D geologic models have been constructed to enable numerical simulations to inform the planning for potential future scientific tests of reservoir response to depressurization at the site.

Alaska↗

USGS2022

Permeability measurement and prediction with nuclear magnetic resonance analysis of gas hydrate-bearing sediments recovered from Alaska North Slope 2018 Hydrate-01 Stratigraphic Test Well

Permeability of porous media, such as oil and gas reservoirs, is the crucial material parameter for predicting their hydraulic behavior. A nuclear magnetic resonance (NMR) analyzer is widely used as a powerful tool to predict permeability of various media. NMR T 2 (transverse or spin–spin) relaxation time distribution, which is related to pore size distribution, gives the information to allow calculation of effective (initial) permeability. In this study, we investigate effective, intrinsic (absolute), and relative water and gas permeabilities of hydrate-bearing pressure core samples. These samples were recovered from the Alaska North Slope 2018 Hydrate-01 Stratigraphic Test Well by sidewall pressure coring and then analyzed in a laboratory using both fluid flow test and NMR analyzer. The peak of the NMR T 2 distribution was measured at 10–20 ms using a laboratory NMR analyzer, which compares well with in situ measurements obtained via logging while drilling NMR data for two samples with high gas hydrate saturations ( S h = 76% and 74%). Further, comparison of laboratory NMR T 2 distribution after hydrate dissociation revealed that the hydrate existed in large pore spaces. Effective permeabilities predicted by the Timur-Coates (TC) model and the Schlumberger-Doll-Research (SDR) model, with T 2 cutoff 33 ms, were about an order of magnitude less than the laboratory measured values. Alternative TC model-based calculations with the T 2 cutoff reduced to 10 ms and a newly developed hydraulic radius model better matched the laboratory data. For the analysis of the intrinsic permeabilities, the TC model with a T 2 cutoff of 33 ms and SDR model were greater than the laboratory derived values, while the hydraulic radius model more closely matched the laboratory-derived values. In addition, permeability measurements were also made relative to gas and water under constant three-phase flow (water–gas–hydrate) conditions. After hydrate dissociation, a relative permeability curve was developed for each of the analyzed core samples based on the Corey petrophysical model. The results indicate that the gas permeability changed rapidly at high water saturation around 90%. Thus, we infer that the selection of relative reservoir parameters should focus on the higher water saturation conditions.

Alaska↗

USGS2022

Comprehensive pressure core analysis for hydrate-bearing sediments from Gulf of Mexico Green Canyon Block 955, including assessments of geomechanical viscous behavior and nuclear magnetic resonance permeability

Quantifying the petrophysical and geomechanical properties of gas hydrate reservoirs is essential for understanding the natural hydrate system and predicting gas production behavior for future resource development. Pressure-core analysis tools were used to characterize methane hydrate–bearing sediments recovered from the Gulf of Mexico Green Canyon Block 955, under an international collaboration with The University of Texas and the National Institute of Advanced Industrial Science and Technology. Pressure-core samples were successfully transferred from Austin, Texas to Sapporo, Japan. Index property measurements (grain size, grain density, hydration number, gas composition, thermal conductivity), along with triaxial compression, consolidation, and permeability tests with a nuclear magnetic resonance (NMR) analyzer were conducted. Compression tests at different strain rates confirmed a strain rate dependence for hydrate-bearing sediment, and an equation for predicting strength as a function of hydrate saturation and strain rate is proposed. Compression and swelling indices were obtained from high-effective stress consolidation tests. Furthermore, secondary compression coefficients for hydrate-bearing sediments were obtained, suggesting that hydrate exhibits creeping behavior on timescales of minutes to hours. A relatively high initial permeability of a few millidarcys was confirmed. In addition, the first NMR signal measurement was performed on a hydrate-bearing pressure core to acquire the NMR transverse or spin-spin ( T 2 ) distribution. Results confirm that the Schlumberger Doll Research model and Timur-Coates model predictions underestimate permeability measured directly via fluid flow. Permeability estimated using specific surface values derived from NMR T 2 distributions is in good agreement with flow test results. Finally, an extended Timur-Coates model was proposed and predicts intrinsic permeability with high accuracy.

Texas↗

USGS2021

Multiple physical properties of gas hydrate-bearing sediments recovered from Alaska North Slope 2018 Hydrate-01 Stratigraphic Test Well

Knowledge of the petrophysical and geomechanical properties of gas hydrate-bearing sediments is essential for predicting reservoir responses to gas production from gas hydrate reservoirs. In December 2018, Stratigraphic Test Well Hydrate-01 was drilled in the western part of the Prudhoe Bay Unit, Alaska North Slope, as part of the technical planning effort for a future long-term gas hydrate production test. Side-wall pressure coring was conducted to recover gas hydrate-bearing sediments from two reservoir sections named Unit B and Unit D. A total of 34 cores were successfully recovered during five runs of a wireline deployed pressure corer, and a total of 17 cores were preserved for advanced laboratory analysis. The samples were frozen inside the pressure core autoclave by liquid nitrogen while at high pressure before being removed and stored under liquid nitrogen at atmospheric pressure. High-resolution X-ray computed tomography showed the samples were high-quality, with undisturbed lithological layers. The Unit B and D sediments were categorized as sand or sandy silt with high hydrate saturation. Gas compositions suggest the hydrates formed with thermogenic and microbial mixed gases. Permeability tests and triaxial compression tests were conducted on the hydrate-bearing sediments. Low strengthening and high permeability at hydrate saturation S h > 80% were observed. There was a small permeability reduction during the triaxial compression tests owing to porosity loss with increasing effective stress in the highly permeable sandy sediment after hydrate dissociation. The apparent minimal changes in porosity and permeability during the tests were due to the low-clay content and low compressibility of the quartz sand grains in the recovered cores. X-ray powder diffraction and thermal conductivity analysis also suggested a high quartz content for the analyzed samples.

Alaska↗

USGS2020

Petrophysical and geomechanical properties of gas hydrate-bearing sediments recovered from Alaska North Slope 2018 Hydrate-01 Stratigraphic Test Well

Knowledge of petrophysical and geomechanical properties of gas hydrate-bearing sediments are essential for predicting reservoir responses to gas production. The same information is also needed for the designing of production well completions such as specifications for artificial lift, test site water storage capacity, and mesh size for the sand control systems. In December 2018, the Stratigraphic Test Well Hydrate-01 was drilled in the western part of the Prudhoe Bay Unit on the Alaska North Slope as part of the technical planning effort for a future long-term production test being planned and led by a collaborative team from the U.S. Department of Energy - National Energy Technology Laboratory (DOE-NETL), U.S. Geological Survey (USGS), and Japan’s Research and Development Consortium for Pore Filling Hydrate in Sand (MH21-S) (Boswell et al., 2020, Collett et al., 2020, Okinaka et al., 2020). Logging-while-drilling (LWD) data were acquired (Haines et al., 2020, Suzuki et al., 2019) and sidewall core sampling depths were selected from the LWD logs. Sidewall pressure coring was conducted to recover gas hydrate-bearing sediments from two reservoir sections named Unit B and Unit D. A total of 34 cores were successfully recovered by 5 runs of a wireline deployed pressure coring system (CoreVault® System - Halliburton). The core analysis plan for this project is shown in Figure 1. Upon recovery, the pressure core autoclaves were transported from the Alaska North Slope to the Stratum Reservoir laboratory in Anchorage Alaska. To access the cores, they were first quenched in liquid nitrogen while still at high pressure in the core system autoclaves (Figure 1a). The cores were next removed from the pressure corer autoclaves with temperature control support from dry ice and stored under liquid nitrogen at atmospheric pressure. A total of 19 disturbed low-quality cores were processed for index property measurements, which included grain size and grain density analysis. Another 4 core samples were depressurized, trimmed, and core plugs were cut from each core and used to measure intrinsic permeabilities of host sediments (Figure 1). Unsteady-state permeability measurements were conducted on two samples to obtain relative water permeability (Rel.-Perm.) to gas and core scale Nuclear Magnetic Resonance (NMR) transverse relaxation time (T2) distribution measurements were performed to evaluate pore size distribution (Figure 1b). A total of 13 remaining high-quality cores with significant gas hydrate concentrations were preserved for advanced laboratory analysis. The National Institute of Advanced Industrial Science and Technology, as a part of the Japanese National Hydrate Research Program (MH21-S, funded by Ministry of Economy, Trade and Industry), received the 13 remaining high-quality core samples at their laboratories in Sapporo, Japan for advanced core analysis. High-resolution X-ray computed tomography (CT) was used to analyze the physical characteristics of the samples, which showed for the most part undisturbed lithological layers. Cores were lathed into cylindrical shapes and prepared for multi property measurements (Figure 1c). As a result, sediment from Unit D was characterized as silty-sand at ~37% porosity with ~80% gas hydrate saturation. An average hydration number n = 6.16 was measured for the recovered gas hydrate samples by Raman spectroscopy. An average intrinsic permeability of ~400 mD and in situ effective permeability (with hydrate) on the order of ~10 mD was measured for a total of five core samples. The Unit B recovered cores consisted of well sorted sand at ~40% porosity with ~95% gas hydrate saturation. An average intrinsic permeability of ~1 Darcy and in situ effective permeability on the order of ~30 mD was measured for the Unit B cores. Additional laboratory measurements yielded small permeability reductions due to porosity loss with increasing effective stress that simulated sediment consolidation along with depressurization in the highly permeable sandy sediment. The apparent limited change in porosity and permeability may be caused by the low compressibility of quartz sand grains in the recovered cores. X-ray diffraction (XRD) and thermal conductivity analysis also indicated a high quartz content within the recovered cores. Completed triaxial compression tests established internal friction angles based on the Mohr-Coulomb's failure criterion, which were calculated at 40° for hydrate-bearing sediment and 29.8° for hydrate free sediment.

Alaska↗

USGS2020

Alaska North Slope 2018 Hydrate-01 Stratigraphic Test Well: Technical results

The Hydrate-01 Stratigraphic Test Well was drilled in December 2018 to confirm that a seismically-identified location within the western Prudhoe Bay Unit might be suitable for extended-duration scientific production testing. The well tested two primary targets: the deeper Unit B is highly favorable due to optimal reservoir temperature and minimal observed risk for direct communication with permeable, hydrate-free water-bearing zones. The shallower Unit D provides a secondary target and opportunity to assess additional scientific and operational issues.

Alaska↗

USGS2020

Gas hydrate saturation estimation from acoustic log data in the 2018 Alaska North Slope Hydrate-01 stratigraphic test well

Completed in December 2018, the Alaska North Slope Hydrate 01 stratigraphic test well provides a wealth of logging-while-drilling (LWD) data for strata to below the base of gas hydrate stability (BGHS). This well is intended to be the first of three wells drilled for a long-term gas hydrate production test to be conducted by the U.S. Department of Energy National Energy Technology Laboratory, the Japan Oil, Gas and Metals National Corporation, and the U.S. Geological Survey (USGS). The Hydrate 01 stratigraphic test well confirmed the presence of gas hydrate in two sand reservoirs within the hydrate stability zone, indicating the suitability of this location for a long-term gas hydrate production test. The USGS, using an effective-medium-theory rock-physics approach, has estimated gas hydrate saturations from compressional (P) and shear (S) wave log data acquired in the Hydrate 01 well. We assume that gas hydrate occurs as pore-filling load-bearing material (i.e., part of the grain matrix). For Unit D, approximately 500 feet above the BGHS, both P-wave and S-wave acoustic logs indicate high gas hydrate saturations with S-wave results slightly lower than those for P-waves. For Unit B, located just above the BGHS, we obtain high gas hydrate saturation estimates from both sonic logs. Our P-wave saturation estimates agree well with results from electrical-resistivity-based estimates, whereas estimates from nuclear magnetic resonance LWD data generally suggest 5 to 10 percent higher saturations; our S-wave results suggest lower saturations. These differences likely indicate complexities in the form of gas hydrate occurrence within the sediment pore space, potentially including differences between hydrate occurrence in Units B and D.

Alaska↗