Search USGS⌕ Search

Geology topics

Jonathan C. Matti

Publications and source records attributed to Jonathan C. Matti.

At least 19 recordsLinked to original sources
USGS2022

Hydrogeology and simulation of groundwater flow in the Lucerne Valley groundwater basin, California

The Lucerne Valley is in the southwestern part of the Mojave Desert and is about 75 miles northeast of Los Angeles, California. The Lucerne Valley groundwater basin encompasses about 230 square miles and is separated from the Upper Mojave Valley groundwater basin by splays of the Helendale Fault. Since its settlement, groundwater has been the primary source of water for agricultural, industrial, municipal, and domestic uses. Groundwater withdrawal from pumping has exceeded the amount of water recharged to the basin, causing groundwater declines of more than 100 feet between 1917 and 2016 in the center of the basin. The continued withdrawal has resulted in an increase in pumping costs, reduced well efficiency, and land subsidence near Lucerne Lake. Although the volume of pumping has declined in recent years, there is concern that new agricultural growth and limits on imported water will continue to strain the sustainability of the groundwater system. To address these concerns, the U.S. Geological Survey entered into a cooperative agreement with the Mojave Water Agency to develop a better understanding of the Lucerne Valley hydrogeologic system and provide tools to help evaluate and manage the effects of future development in the Lucerne Valley. The objectives of this study were to (1) improve the understanding of the aquifer system, (2) improve the understanding of subsidence in the basin, and (3) incorporate the understanding into a groundwater-flow model that can be used to help manage the groundwater resources in the Lucerne Valley. The model developed for this study covers the period of 1942–2016 and can help evaluate various proposed water-management scenarios during different climatic and hydrologic conditions. The aquifer system consists of a shallow aquifer, a confining unit, and middle and lower aquifers. These layered water-bearing units were identified based on geologic units of the mostly unconsolidated sediments and hydrologic properties. These alluvial deposits consist of clay, silt, sand, and gravel; some places also contain clay and silty clay lacustrine deposits. Several faults act, at least in part, as barriers to groundwater flow on the eastern, southern, and western edges of the basin. Present-day natural recharge is primarily from the infiltration of runoff from the San Bernardino Mountains to the south; however, stable and radioactive isotopes show that groundwater from the middle of the Lucerne Valley was older than about 10,000 years and probably was recharged as infiltration from streams draining the mountains in the Mojave Desert to the north, which probably does not occur under present-day climatic conditions. The annual average natural recharge for 1942–2016, estimated by a Basin Characterization Model, was about 635 acre-feet per year; the average amount of treated wastewater effluent transferred to the Lucerne Valley for artificial recharge annually ranged from about 1,500 to 4,000 acre-feet per year during 1980–2016. Pumpage estimates for 1942–2016 ranged from about 3,000 acre-feet in 1942 to about 18,300 acre-feet in 1984. The total cumulative amount of groundwater removed from the basin by pumping between 1942 and 2016 was estimated to be about 700,000 acre-feet, which was about 10 times greater than the cumulative amount of recharge to the entire Lucerne Valley groundwater basin. Before groundwater development, the direction of groundwater flow was from the southern part of the basin northward to discharge areas near Lucerne Lake, where it discharged through springs along the Helendale Fault and by evapotranspiration. Since the early 1900s, groundwater-level declines have mostly eliminated the areas where natural discharge occurred and exceeded 100 feet in the middle of the basin between the early 1950s and mid-1990s, and as much as 25 feet near the margins from about the mid-1950s to 2000s. A decrease in the rate of pumping after the mid-1990s lessened the hydraulic stress on the middle and lower aquifers and enabled hydraulic heads in the middle of the basin to recover slightly as groundwater near the margins of the basin moved toward the pumping depression. Although trends in groundwater levels in the center of the basin have reversed since the mid-1990s, levels at the basin margins continue to decline as the movement of groundwater from the margins fills the pumping depression and gradually flattens the groundwater table throughout the basin. The long-term extraction of groundwater and associated dewatering of the fine-grained sediments present within the aquifer system has resulted in aquifer compaction and consequently land subsidence, primarily near Lucerne Lake. Analysis of interferometric synthetic aperture radar data shows that almost 11 inches of land subsidence has occurred south of Lucerne Lake between April 1992 and November 2009; less subsidence occurred elsewhere in the basin during this period. This differential land subsidence has caused fissures and cracks in the ground surface, which have buckled the pavement and undercut roads in several locations. The Lucerne Valley Hydrologic Model was developed using the finite-difference groundwater modeling software One Water Hydrologic Model to represent the hydrologic conditions and stresses during 1942–2016. The model has a uniform grid of approximately 92 acres per cell (2,000 feet by 2,000 feet) and has four layers representing the water-bearing units. The results from the calibrated model simulations indicated that groundwater pumpage exceeded recharge, resulting in an estimated net cumulative depletion of groundwater storage (discharge minus recharge) of about 465,000 acre-feet from 1942 to 2016. The model simulated as much as 7.5 feet (90 inches; 2,286 millimeters) of aquifer compaction, which indicates the extensive fine-grained deposits and measured subsidence near Lucerne Lake.

California↗
USGS2022

Geologic and geomorphic evidence for multi-phase history of strands of the San Andreas fault through the San Gorgonio Pass structural knot, southern California

The San Gorgonio Pass region of southern California is a locus of extensive Quaternary deformation within a multi-strand section of the San Andreas fault zone. The geomorphology of the San Gorgonio Pass region reflects the complicated history of geologic events in the formation of this structurally complex region. We define fault-bounded blocks in San Gorgonio Pass and focus on two that are characterized by extensive crystalline bedrock outcrops with similar bedrock lithologies. These two blocks are separated by the San Bernardino strand of the San Andreas fault. Morphometric variables, including local relief, slope, slope distribution, and surface roughness, consistently demonstrate distinctions between the bedrock upland regions of the two blocks. Geologic observations of the region highlight differences in Quaternary units within the two blocks, reflective of the differing surficial processes active in each block. Within the Kitching Peak block, the morphology highlights a lineament that we informally name the Lion Canyon lineament. This boundary more clearly differentiates the two regions, as compared to the mapped San Bernardino strand, and may represent the previously active strand or bounding structure in this section. The distinction in morphology and surficial processes leads to our interpretation that the Kitching Peak and Pisgah Peak blocks have experienced different uplift histories. This further leads to the conclusion that the San Bernardino strand, broadly defined, has been integrated, at some point in the past, with the Banning strand, allowing for through-going rupture along the fault system. This connectivity may have occurred along the Burro Flats section of the San Bernardino strand or the Lion Canyon lineament. The fault connection along the mapped trace of the San Bernardino strand is not currently evident at the surface, however, suggesting that the integration has been disrupted. We propose this is due to intervals of N-S compression in the region, manifest as slip along the San Gorgonio Pass fault zone and other regional faults. We present evidence for lateral displacement along the San Bernardino and Banning strands of the San Andreas fault, discuss the implications of these displacements, and propose a sequence of fault activity, including multiple phases of activity along the San Bernardino and Banning strand pathway to account for the structural complexity and lack of surficial fault continuity.

California↗
USGS2022

Geology and hydrogeology of the Yucaipa groundwater subbasin, San Bernardino and Riverside Counties, California

The Yucaipa groundwater subbasin (referred to in this report as the Yucaipa subbasin) is located about 75 miles (mi) east of of Los Angeles and about 12 mi southeast of the City of San Bernardino. In the Yucaipa subbasin, as in much of southern California, limited annual rainfall and large water demands can strain existing water supplies; therefore, understanding local surface water and groundwater conditions is essential for managing these resources. To better understand the hydrogeology and water resources in the Yucaipa subbasin, especially groundwater, the San Bernardino Valley Municipal Water District and the U.S. Geological Survey initiated a cooperative study to evaluate the hydrogeologic system of the Yucaipa subbasin and the encompassing Yucaipa Valley watershed. Previous studies of the area provided information on general geologic and hydrologic conditions, but this study provides the first comprehensive definition of the hydrogeology of the subsurface throughout the entire subbasin. The Yucaipa subbasin is located between the northwest trending San Andreas fault zone and San Jacinto fault. Several northeast-trending dip-slip faults dissect the Yucaipa subbasin, providing the mechanism for structural relief within the sediment-filled subbasin and between the subbasin and surrounding mountains and highlands. Several of these dip-slip faults have been previously identified as potential barriers to groundwater flow. This report provides a synthesis of previous studies and a discussion of the geologic interpretations that were used as the foundation for hydrogeologic classification of the Yucaipa subbasin. Notably, this report (1) adopts the recently named and classified sedimentary deposits of Live Oak Canyon geologic formation and extends the mapped distribution of the formation into the Yucaipa subbasin, and (2) adopts the interpretation that activity along the Banning fault predates the deposition of most basin-fill sedimentary materials in the Yucaipa subbasin. Four hydrogeologic units were classified in the Yucaipa subbasin: (1) crystalline basement, (2) consolidated sedimentary materials, (3) unconsolidated sediment, and (4) surficial materials. The crystalline basement unit forms the bottom boundary of the aquifer system, and the three other units comprise the basin-fill aquifer system. The four hydrogeologic units vary in extent, thickness, and structural relief across the subbasin, with the unconsolidated sediment unit serving as the primary aquifer unit. A three-dimensional hydrogeologic framework model was developed for the Yucaipa subbasin and surrounding area to characterize the thickness, extent, and hydrogeologic variability of the aquifer system. Geologic maps, borehole geophysical logs, drillers’ lithology logs, and depth-to-basement gravity data were used to map and interpolate the subsurface extent and structure of the hydrogeologic units within the subbasin. Faults and structures of geologic and (or) hydrogeologic importance were included in the model for future evaluation of their potential effects on groundwater flow. The resulting hydrogeologic framework is consistent with existing geologic concepts and the tectonic and structural history of the Yucaipa subbasin and surrounding area. The framework is also suitable for use in basin-scale hydrogeologic investigations.

California↗
USGS2018

Evaluation of the Source and Transport of High Nitrate Concentrations in Ground Water, Warren Subbasin, California

Ground water historically has been the sole source of water supply for the Town of Yucca Valley in the Warren subbasin of the Morongo ground-water basin, California. An imbalance between ground-water recharge and pumpage caused ground-water levels in the subbasin to decline by as much as 300 feet from the late 1940s through 1994. In response, the local water district, Hi-Desert Water District, instituted an artificial recharge program in February 1995 using imported surface water to replenish the ground water. The artificial recharge program resulted in water-level recoveries of as much as 250 feet in the vicinity of the recharge ponds between February 1995 and December 2001; however, nitrate concentrations in some wells also increased from a background concentration of 10 milligrams per liter to more than the U.S. Environmental Protection Agency (USEPA) maximum contaminant level (MCL) of 44 milligrams per liter (10 milligrams per liter as nitrogen). The objectives of this study were to: (1) evaluate the sources of the high-nitrate concentrations that occurred after the start of the artificial-recharge program, (2) develop a ground-water flow and solute-transport model to better understand the source and transport of nitrates in the aquifer system, and (3) utilize the calibrated models to evaluate the possible effect of a proposed conjunctive-use project. These objectives were accomplished by collecting water-level and water-quality data for the subbasin and assessing changes that have occurred since artificial recharge began. Collected data were used to calibrate the ground-water flow and solute-transport models. Data collected for this study indicate that the areal extent of the water-bearing deposits is much smaller (about 5.5 square miles versus 19 square miles) than that of the subbasin. These water-bearing deposits are referred to in this report as the Warren ground-water basin. Faults separate the ground-water basin into five hydrogeologic units: the west, the midwest, the mideast, the east and the northeast hydrogeologic units. Water-quality analyses indicate that septage from septic tanks is the primary source of the high-nitrate concentrations measured in the Warren ground-water basin. Water-quality and stable-isotope data, collected after the start of the artificial recharge program, indicate that mixing occurs between imported water and native ground water, with the highest recorded nitrate concentrations in the midwest and the mideast hydrogeologic units. In general, the timing of the increase in measured nitrate concentrations in the midwest hydrogeologic unit is directly related to the distance of the monitoring well from a recharge site, indicating that the increase in nitrate concentrations is related to the artificial recharge program. Nitrate-to-chloride and nitrogen-isotope data indicate that septage is the source of the measured increase in nitrate concentrations in the midwest and the mideast hydrogeologic units. Samples from four wells in the Warren ground-water basin were analyzed for caffeine and selected human pharmaceutical products; these analyses suggest that septage is reaching the water table. There are two possible conceptual models that explain how high-nitrate septage reaches the water table: (1) the continued downward migration of septage through the unsaturated zone to the water table and (2) rising water levels, a result of the artificial recharge program, entraining septage in the unsaturated zone. The observations that nitrate concentrations increase in ground-water samples from wells soon after the start of the artificial recharge program in 1995 and that the largest increase in nitrate concentrations occur in the midwest and mideast hydrogeologic units where the largest increase in water levels occur indicate the validity of the second conceptual model (rising water levels). The potential nitrate concentration resulting from a water-level rise in the midwest and mideast hydrogeologic units was estimated using a simple mixing-cell model. The estimated value is within the range of concentrations measured in samples from wells, further indicating the validity of the second conceptual model. A ground-water flow model and a solute-transport model were developed for the Warren ground-water basin for the period 1956-2001. MODFLOW-96 was used for the ground-water flow model and MOC3D was used for the solute-transport model. The model cell size is about 500 feet by 500 feet and the models were discretized vertically into three layers. The models were calibrated using a trial-and-error approach using water-level and nitrate-concentration data collected between 1956-2001. In order to better match the measured data, low fault hydraulic characteristic values were required, thereby compartmentalizing the ground-water basin. In addition, it was necessary to parameterize the specific yield distribution for the top model layer where unconfined ground-water conditions occur into three homogeneous zones. Separate sets of specific- yield values were needed to simulate the drawdown and subsequent water-level recovery. In addition, the calibrated natural recharge was about 83 acre-feet per year. The entrainment of unsaturated-zone septage was simulated as recharge having an associated nitrate concentration. The volume of recharge was a function of the measured water-level rise between 1994-98 and the moisture content of the unsaturated zone. The nitrate concentration of the recharge water was a weighted function of the assumed nitrate concentration in the infiltrating water associated with the overlying land use. The simulated hydraulic head and nitrate concentration results were in good agreement with the measured data indicating that the mechanism for the increase in nitrate concentrations was rising water levels entraining high-nitrate septage in the unsaturated-zone. The calibrated models were used to simulate the possible effects of a planned conjunctive-use project in the western part of the ground-water basin. The simulated project included the addition of a new recharge pond and a new extraction well. In addition, recharge at two existing recharge ponds was increased and three existing production wells were pumped, treated in a nitrate-removal facility, and used for water supply. The simulated hydraulic heads increased in the west, the mideast, and parts of the east hydrogeologic units; however, the simulated hydraulic heads decreased in the midwest and northeast hydrogeologic units. The simulated nitrate concentrations increased to above the MCL of 44 milligrams per liter (10 milligrams per liter as nitrogen) in parts of the west as a result of the increase in simulated hydraulic head. The simulated nitrate concentrations decreased in part of the midwest hydrogeologic unit as a result of the artificial recharge and pumping from the nitrate-removal wells. The simulated nitrate concentrations increased to above the MCL of 44 milligrams per liter in part of the mideast and parts of the east hydrogeologic units beneath commercial land-use areas.

California↗
USGS2016

High-resolution gravity and seismic-refraction surveys of the Smoke Tree Wash area, Joshua Tree National Park, California

We describe high-resolution gravity and seismic refraction surveys acquired to determine the thickness of valley-fill deposits and to delineate geologic structures that might influence groundwater flow beneath the Smoke Tree Wash area in Joshua Tree National Park. These surveys identified a sedimentary basin that is fault-controlled. A profile across the Smoke Tree Wash fault zone reveals low gravity values and seismic velocities that coincide with a mapped strand of the Smoke Tree Wash fault. Modeling of the gravity data reveals a basin about 2–2.5 km long and 1 km wide that is roughly centered on this mapped strand, and bounded by inferred faults. According to the gravity model the deepest part of the basin is about 270 m, but this area coincides with low velocities that are not characteristic of typical basement complex rocks. Most likely, the density contrast assumed in the inversion is too high or the uncharacteristically low velocities represent highly fractured or weathered basement rocks, or both. A longer seismic profile extending onto basement outcrops would help differentiate which scenario is more accurate. The seismic velocities also determine the depth to water table along the profile to be about 40–60 m, consistent with water levels measured in water wells near the northern end of the profile.

California↗
USGS2015

Geology of Joshua Tree National Park geodatabase

The database in this Open-File Report describes the geology of Joshua Tree National Park and was completed in support of the National Cooperative Geologic Mapping Program of the U.S. Geological Survey (USGS) and in cooperation with the National Park Service (NPS). The geologic observations and interpretations represented in the database are relevant to both the ongoing scientific interests of the USGS in southern California and the management requirements of NPS, specifically of Joshua Tree National Park (JOTR). Joshua Tree National Park is situated within the eastern part of California’s Transverse Ranges province and straddles the transition between the Mojave and Sonoran deserts. The geologically diverse terrain that underlies JOTR reveals a rich and varied geologic evolution, one that spans nearly two billion years of Earth history. The Park’s landscape is the current expression of this evolution, its varied landforms reflecting the differing origins of underlying rock types and their differing responses to subsequent geologic events. Crystalline basement in the Park consists of Proterozoic plutonic and metamorphic rocks intruded by a composite Mesozoic batholith of Triassic through Late Cretaceous plutons arrayed in northwest-trending lithodemic belts. The basement was exhumed during the Cenozoic and underwent differential deep weathering beneath a low-relief erosion surface, with the deepest weathering profiles forming on quartz-rich, biotite-bearing granitoid rocks. Disruption of the basement terrain by faults of the San Andreas system began ca. 20 Ma and the JOTR sinistral domain, preceded by basalt eruptions, began perhaps as early as ca. 7 Ma, but no later than 5 Ma. Uplift of the mountain blocks during this interval led to erosional stripping of the thick zones of weathered quartz-rich granitoid rocks to form etchplains dotted by bouldery tors—the iconic landscape of the Park. The stripped debris filled basins along the fault zones. Mountain ranges and basins in the Park exhibit an east-west physiographic grain controlled by left-lateral fault zones that form a sinistral domain within the broad zone of dextral shear along the transform boundary between the North American and Pacific plates. Geologic and geophysical evidence reveal that movement on the sinistral faults zones has resulted in left steps along the zones, resulting in the development of sub-basins beneath Pinto Basin and Shavers and Chuckwalla Valleys. The sinistral fault zones connect the Mojave Desert dextral faults of the Eastern California Shear Zone to the north and east with the Coachella Valley strands of the southern San Andreas Fault Zone to the west. Quaternary surficial deposits accumulated in alluvial washes and playas and lakes along the valley floors; in alluvial fans, washes, and sheet wash aprons along piedmonts flanking the mountain ranges; and in eolian dunes and sand sheets that span the transition from valley floor to piedmont slope. Sequences of Quaternary pediments are planed into piedmonts flanking valley-floor and upland basins, each pediment in turn overlain by successively younger residual and alluvial surficial deposits.

California↗
USGS2015

Late Quaternary slip history of the Mill Creek strand of the San Andreas fault in San Gorgonio Pass, southern California: The role of a subsidiary left-lateral fault in strand switching

The fault history of the Mill Creek strand of the San Andreas fault (SAF) in the San Gorgonio Pass region, along with the reconstructed geomorphology surrounding this fault strand, reveals the important role of the left-lateral Pinto Mountain fault in the regional fault strand switching. The Mill Creek strand has 7.1–8.7 km total slip. Following this displacement, the Pinto Mountain fault offset the Mill Creek strand 1–1.25 km, as SAF slip transferred to the San Bernardino, Banning, and Garnet Hill strands. An alluvial complex within the Mission Creek watershed can be linked to palinspastic reconstruction of drainage segments to constrain slip history of the Mill Creek strand. We investigated surface remnants through detailed geologic mapping, morphometric and stratigraphic analysis, geochronology, and pedogenic analysis. The degree of soil development constrains the duration of surface stability when correlated to other regional, independently dated pedons. This correlation indicates that the oldest surfaces are significantly older than 500 ka. Luminescence dates of 106 ka and 95 ka from (respectively) 5 and 4 m beneath a younger fan surface are consistent with age estimates based on soil-profile development. Offset of the Mill Creek strand by the Pinto Mountain fault suggests a short-term slip rate of ∼10–12.5 mm/yr for the Pinto Mountain fault, and a lower long-term slip rate. Uplift of the Yucaipa Ridge block during the period of Mill Creek strand activity is consistent with thermochronologic modeled uplift estimates.

Geological Society of America Bulletin↗
USGS2012

Basin thickness variations at the Junction of the Eastern California Shear Zone and the San Bernardino Mountains, California: How thick could the Pliocene sections be?

We estimate the thickness of Neogene basin fill along the junction of the Eastern California Shear Zone and the North Frontal thrust system of the San Bernardino Mountains using gravity data with geologic and well log constraints. The geometry of the basin fill is of interest for groundwater assessment and location of potential faults, as well as providing an upper bound on the thickness of any potential, buried Pliocene sediments. Nearly one thousand new gravity measurements were collected along the North Frontal thrust system from Hesperia to Johnson Valley. Three-dimensional inverse modeling of the new and existing gravity data shows that Neogene deposits are segmented into basins along the range front of the San Bernardino Mountains. The Helendale fault, a dextral fault in the Eastern California Shear Zone, separates shallower basement (approximately 300 m depth) beneath Lucerne Valley east of the fault from deeper basement (approximately 550 m or more) west of the fault. The thickest part of the basin fill is generally located near the San Bernardino Mountains and the basin shallows northward. The amount of throw on the North Frontal thrust appears to decrease eastward, as the gravity gradient associated with the fault diminishes in amplitude. The thickness of basin fill away from the North Frontal system and east of the Helendale fault is less than 100 to 200 m, except for local pockets generally developed along strike-slip faults of the Eastern California Shear Zone and local east-west oriented depressions associated with folding of the basin fill.

Conference Paper↗
USGS2003

Geologic map and digital database of the Yucaipa 7.5’ quadrangle, San Bernardino and Riverside Counties, California

Introduction This geologic database of the Yucaipa 7.5' quadrangle was prepared by the Southern California Areal Mapping Project (SCAMP), a regional geologic-mapping project sponsored jointly by the U.S. Geological Survey and the California Geological Survey. The database was developed as a contribution to the National Cooperative Geologic Mapping Program's National Geologic Map Database, and is intended to provide a general geologic setting of the Yucaipa quadrangle. The database and map provide information about earth materials and geologic structures, including faults and folds that have developed in the quadrangle due to complexities in the San Andreas Fault system. The Yucaipa 7.5' quadrangle contains materials and structures that provide unique insight into the Mesozoic and Cenozoic geologic evolution of southern California. Stratigraphic and structural elements include: (1) strands of the San Andreas Fault that bound far-traveled terranes of crystalline and sedimentary rock; (2) Mesozoic crystalline rocks that form lower and upper plates of the regionwide Vincent-Orocopia Thrust system; and (3) late Tertiary and Quaternary sedimentary materials and geologic structures that formed during the last million years or so and that record complex geologic interactions within the San Andreas Fault system. These materials and the structures that deform them provide the geologic framework for investigations of geologic hazards and ground-water recharge and subsurface flow. Geologic information contained in the Yucaipa database is general-purpose data that is applicable to land-related investigations in the earth and biological sciences. The term "generalpurpose" means that all geologic-feature classes have minimal information content adequate to characterize their general geologic characteristics and to interpret their general geologic history. However, no single feature class has enough information to definitively characterize its properties and origin. For this reason the database cannot be used for site-specific geologic evaluations, although it can be used to plan and guide investigations at the site-specific level.

California↗
USGS2003

Geologic map and digital database of the Redlands 7.5' quadrangle, San Bernardino and Riverside Counties, California

This geologic database of the Redlands 7.5' quadrangle was prepared by the Southern California Areal Mapping Project (SCAMP), a regional geologic-mapping project sponsored jointly by the U.S. Geological Survey and the California Geological Survey. The database was developed as a contribution to the National Cooperative Geologic Mapping Program's National Geologic Map Database, and is intended to provide a general geologic setting of the Redlands quadrangle. The database and map provide information about earth materials and geologic structures, including faults and folds that have developed in the quadrangle due to complexities in the San Andreas Fault system. The Redlands 7.5' quadrangle contains earth materials and structures that provide insight into the late Cenozoic geologic evolution of the southern California Inland Empire region. Important stratigraphic and structural elements include (1) the modern trace of the San Andreas and San Jacinto faults and (2) late Tertiary and Quaternary sedimentary materials and geologic structures that formed during the last million years or so and that record complex geologic interactions within the San Andreas Fault system. These materials and the structures that deform them provide the geologic framework for investigations of earthquake hazards and ground-water recharge and subsurface flow. Geologic information contained in the Redlands database is general-purpose data that is applicable to land-related investigations in the earth and biological sciences. The term "general-purpose" means that all geologic-feature classes have minimal information content adequate to characterize their general geologic characteristics and to interpret their general geologic history. However, no single feature class has enough information to definitively characterize its properties and origin. For this reason the database cannot be used for site-specific geologic evaluations, although it can be used to plan and guide investigations at the site-specific level. This summary pamphlet discusses major categories of surficial materials in the Redlands quadrangle, and provides a conceptual framework and basis for how geologicmap units containing such materials are recognized and correlated.

California↗
USGS2001

Geologic map of the Devore 7.5' quadrangle, San Bernardino County, California

This Open-File Report contains a digital geologic map database of the Devore 7.5' quadrangle, San Bernardino County, California, that includes: 1. ARC/INFO (Environmental Systems Research Institute) version 7.2.1 coverages of the various components of the geologic map 2. A PostScript (.ps) file to plot the geologic map on a topographic base, containing a Correlation of Map Units diagram, a Description of Map Units, an index map, and a regional structure map 3. Portable Document Format (.pdf) files of: a. This Readme; includes an Appendix, containing metadata details found in devre_met.txt b. The same graphic as plotted in 2 above. (Test plots from this .pdf do not produce 1:24,000-scale maps. Adobe Acrobat page-size settings control map scale.) The Correlation of Map Units and Description of Map Units are in the editorial format of USGS Miscellaneous Investigations Series maps (I-maps) but have not been edited to comply with I-map standards. Within the geologic-map data package, map units are identified by such standard geologic-map criteria as formation name, age, and lithology. Even though this is an author-prepared report, every attempt has been made to closely adhere to the stratigraphic nomenclature of the U.S. Geological Survey. Descriptions of units can be obtained by viewing or plotting the .pdf file (3b above) or plotting the postscript file (2 above). If roads in some areas, especially forest roads that parallel topographic contours, do not show well on plots of the geologic map, we recommend use of the USGS Devore 7.5’ topographic quadrangle in conjunction with the geologic map.

California↗
USGS2001

Geologic map of the Lakeview 7.5' quadrangle, Riverside County, California

This Open-File Report contains a digital geologic map and map database of the Lakeview 7.5' quadrangle, Riverside County, California, that includes: 1. ARC/INFO (Environmental Systems Research Institute) version 7.2.1 double-precision coverages of the various elements of the geologic map 2. A Postscript file to plot the geologic map on a topographic base, and containing a Correlation of Map Units diagram and a Description of Map Units 3. Portable Document Format (.pdf) files of: a. This Readme; includes, in Appendix I, data contained in lkvw_met.txt b. The same graphic as plotted in 2 above. (Test plots from this .pdf do not produce 1:24,000-scale maps. Adobe Acrobat page size settings control map scale.) This release includes features not found in most other digital geologic maps, in that all polygons, lines, and points in the coverage are encoded with detailed, comprehensive, contained in five INFO data tables (.rel) (see Matti and others, 1998a, 1998b, and 1998c for information on how the encoding may be accessed and utilized). No paper map is included in this report, but a PostScript plot file containing an image of the geologic map sheet, topographic base, Correlation of Map Units (CMU), and detailed Description of Map Units (DMU) is. Within the geologic map data package, map units are identified by standard geologic map criteria such as formation name, age, and lithology. Even though this is an author-prepared report, every attempt has been made to closely adhere to the stratigraphic nomenclature of the U. S. Geological Survey. Descriptions of units can be obtained by viewing or plotting the .pdf file (3b above) or plotting the postscript file (2 above). If roads in some areas, especially roads that parallel topographic contours, do not show well on plots of the geologic map, we recommend use of the USGS Lakeview 7.5' topographic quadrangle in conjunction with the geologic map.

California↗
USGS2001

Geologic map of the Sunnymead 7.5' quadrangle, Riverside County, California

Open-File Report 01-450 contains a digital geologic map database of the Sunnymead 7.5’ quadrangle, Riverside County, California that includes: ARC/INFO (Environmental Systems Research Institute, http:/www.esri.com) version 7.2.1 coverages of the various elements of the geologic map. A Postscript file to plot the geologic map on a topographic base, containing a Correlation of Map Units diagram (CMU), a Description of Map Units (DMU), and an index map. Portable Document Format (.pdf) files of: a. This Readme; includes in Appendix I, data contained in sun_met.txt b. The same graphic as plotted in 2 above. Test plots have not produced 1:24,000-scale map sheets. Adobe Acrobat page size setting influences map scale. The Correlation of Map Units and Description of Map Units is in the editorial format of USGS Geologic Investigations Series (I-series) maps but has not been edited to comply with I-map standards. Within the geologic map data package, map units are identified by standard geologic map criteria such as formation-name, age, and lithology. Where known, grain size is indicated on the map by a subscripted letter or letters following the unit symbols as follows: lg, large boulders; b, boulder; g, gravel; a, arenaceous; s, silt; c, clay; e.g. Qyfa is a predominantly young alluvial fan deposit that is arenaceous. Multiple letters are used for more specific identification or for mixed units, e.g., Qfysa is a silty sand. In some cases, mixed units are indicated by a compound symbol; e.g., Qyf2sc. Marine deposits are in part overlain by local, mostly alluvial fan, deposits and are labeled Qomf. Grain size follows f. Even though this is an Open-File Report and includes the standard USGS Open-File disclaimer, the report closely adheres to the stratigraphic nomenclature of the U.S. Geological Survey. Descriptions of units can be obtained by viewing or plotting the .pdf file (3b above) or plotting the postscript file (2 above).

California↗
USGS2000

Digital geologic map of the Butler Peak 7.5' quadrangle, San Bernardino County, California

Open-File Report 00-145, is a digital geologic map database of the Butler Peak 7.5' quadrangle that includes (1) ARC/INFO ( Environmental Systems Research Institute ) version 7.2.1 Patch 1 coverages, and associated tables, (2) a Portable Document Format (.pdf) file of the Description of Map Units, Correlation of Map Units chart, and an explanation of symbols used on the map, btlrpk_dcmu.pdf, (3) a Portable Document Format file of this Readme, btlrpk_rme.pdf (the Readme is also included as an ascii file in the data package), and (4) a PostScript plot file of the map, Correlation of Map Units, and Description of Map Units on a single sheet, btlrpk.ps. No paper map is included in the Open-File report, but the PostScript plot file (number 4 above) can be used to produce one. The PostScript plot file generates a map, peripheral text, and diagrams in the editorial format of USGS Geologic Investigation Series (I-series) maps.

California↗
USGS2000

Geologic map and digital database of the Cougar Buttes 7.5' quadrangle, San Bernardino County, California

The Southern California Areal Mapping Project (SCAMP) of Geologic Division has undertaken regional geologic mapping investigations in the Lucerne Valley area co-sponsored by the Mojave Water Agency and the San Bernardino National Forest. These investigations span the Lucerne Valley basin from the San Bernardino Mountains front northward to the basin axis on the Mojave Desert floor, and from the Rabbit Lake basin east to the Old Woman Springs area. Quadrangles mapped include the Cougar Buttes 7.5' quadrangle, the Lucerne Valley 7.5' quadrangle (Matti and others, in preparation b), the Fawnskin 7.5' quadrangle (Miller and others, 1998), and the Big Bear City 7.5' quadrangle (Matti and others, in preparation a). The Cougar Buttes quadrangle has been mapped previously at scales of 1:62,500 (Dibblee, 1964) and 1:24,000 (Shreve, 1958, 1968; Sadler, 1982a). In line with the goals of the National Cooperative Geologic Mapping Program (NCGMP), our mapping of the Cougar Buttes quadrangle has been directed toward generating a multipurpose digital geologic map database. Guided by the mapping of previous investigators, we have focused on improving our understanding and representation of late Pliocene and Quaternary deposits. In cooperation with the Water Resources Division of the U.S. Geological Survey, we have used our mapping in the Cougar Buttes and Lucerne Valley quadrangles together with well log data to construct cross-sections of the Lucerne Valley basin (R.E. Powell, unpublished data, 1996-1998) and to develop a hydrogeologic framework for the basin. Currently, our mapping in these two quadrangles also is being used as a base for studying soils on various Quaternary landscape surfaces on the San Bernardino piedmont (Eppes and others, 1998). In the Cougar Buttes quadrangle, we have endeavored to represent the surficial geology in a way that provides a base suitable for ecosystem assessment, an effort that has entailed differentiating surficial veneers on piedmont and pediment surfaces and distinguishing the various substrates found beneath these veneers.

California↗
USGS1993

Extension and contraction within an evolving divergent strike-slip fault complex: The San Andreas and San Jacinto fault zones at their convergence in southern California

A variety of extensional and contractional structures is produced by strike slip faulting. The variety and extent of the structures are directly related to the kind and extent of geometric complexities of the fault zone or system. The area of convergence of the San Andreas fault zone and the much younger San Jacinto fault zone in the eastern Transverse Ranges is exquisitely complex. We propose that the San Jacinto fault zone formed in response to a structural knot in San Gorgonio Pass probably within the past 1.5 Ma. In the area of their convergence we propose that slip is transferred both east and west from the San Jacinto fault zone northward to the San Andreas fault zone over a 60-to 70-km band that extends northwestward from the south end of the San Bernardino basin to the east end of the San Gabriel Mountains. We further propose several structural adjustments as a consequence of onset or acceleration of lateral movement on the San Jacinto fault zone: accelerated uplift of the eastern San Gabriel Mountains, development or accentuation of an arcuate schuppen-like structure in the eastern San Gabriel Mountains, inception of the San Bernardino basin, cessation of deposition in the present-day San Timoteo badlands area, inception of the San Jacinto basin, and an increase in compression and uplift in the San Gorgonio Pass area. We interpret the uplift and compression in San Gorgonio Pass to result from two formerly disparate structural blocks—the eastern San Bernardino and San Jacinto blocks—becoming a relatively coherent block, and the San Gorgonio Pass area constituting a left step between the San Andreas fault zone in the Coachella Valley area and the San Jacinto fault zone in the San Jacinto Valley area. The compression and uplift led to the formation of the San Gorgonio Pass thrust faults and disruption of any through-going San Andreas strands, at least at the surface. In partitioning slip between the San Andreas and San Jacinto fault zones, consideration should be given to the bandwidth over which horizontal strain has accumulated. The average slip rate of the northern part of the San Jacinto fault zone during the past 1.5 m.y. may have been about 20 mm/yr and about 15 mm/yr on the San Andreas. South of the San Bernardino basin, current strain accumulation based on repeated geodetic surveys is nearly equally divided between the San Jacinto and San Andreas fault zones.

California↗
USGS1983

Mineral resource potential map of the Raywood Flat Roadless Areas, Riverside and San Bernardino counties, California

Geologic, geochemical, and geophysical studies within the Raywood "Flat Roadless Areas, together with an investigation of mines and prospects within the further planning area, resulted in (1) identification of nonmetallic mineral resources at a marble mine in the further planning area and (2) recognition of a small area in the recommended wilderness that has moderate potential for base-metal resources. Except for these two areas of identified and suspected resources, we did not observe indications of resource potential elsewhere in the Raywood Flat Roadless Areas. The area having nonmetallic mineral resources is in the vicinity of the Mill Creek mine near the northeastern boundary of the further planning area (B5-187); there, we identified marginal reserves of marble suitable for the production of lime and construction stone. The reserves are marginal because of their remote location and poor accessibility. Geologic mapping did not reveal any additional marble occurrences within the study area. The area having moderate potential for base-metal resources forms a small zone in the eastern part of the recommended wilderness (A5-187). Within this zone, evidence provided by stream-sediment geochemistry suggests that crystalline bedrocks in several drainages contain concentrations of metallic elements. Because the terrain is inaccessible and covered with dense brush, most of the bedrock in the specific drainages containing the geochemical anomalies could not be examined. Thus, although we infer that mineral occurrences exist in the drainage basins, we have little data on which to base an estimate of their extent and quality. Locally, the crystalline rocks probably contain hydrothermal veins or disseminated occurrences where lead, copper, molybdenum, tin, cobalt, bismuth, and arsenic have been concentrated. However, the geochemical anomalies for these metals are small, and the stream drainages also are relatively small. Therefore, the inferred occurrences of metallic minerals probably are small scale, scattered, and low grade. There is only low probability that the inferred mineral occurrences are large scale.

California↗