Geology topics

John F. DeWild

Publications and source records attributed to John F. DeWild.

34 records · Page 2Linked to original sources

USGS2015

Use of stable isotope signatures to determine mercury sources in the Great Lakes

Sources of mercury (Hg) in Great Lakes sediments were assessed with stable Hg isotope ratios using multicollector inductively coupled plasma mass spectrometry. An isotopic mixing model based on mass-dependent (MDF) and mass-independent fractionation (MIF) (δ 202 Hg and Δ 199 Hg) identified three primary Hg sources for sediments: atmospheric, industrial, and watershed-derived. Results indicate atmospheric sources dominate in Lakes Huron, Superior, and Michigan sediments while watershed-derived and industrial sources dominate in Lakes Erie and Ontario sediments. Anomalous Δ 200 Hg signatures, also apparent in sediments, provided independent validation of the model. Comparison of Δ 200 Hg signatures in predatory fish from three lakes reveals that bioaccumulated Hg is more isotopically similar to atmospherically derived Hg than a lake’s sediment. Previous research suggests Δ 200 Hg is conserved during biogeochemical processing and odd mass-independent fractionation (MIF) is conserved during metabolic processing, so it is suspected even is similarly conserved. Given these assumptions, our data suggest that in some cases, atmospherically derived Hg may be a more important source of MeHg to higher trophic levels than legacy sediments in the Great Lakes.

Lake Erie, Lake Huron, Lake Michigan, Lake Ontario↗

USGS2015

Mercury, monomethyl mercury, and dissolved organic carbon concentrations in surface water entering and exiting constructed wetlands treated with metal-based coagulants, Twitchell Island, California

Coagulation with metal-based salts is a practice commonly employed by drinking-water utilities to decrease particle and dissolved organic carbon concentrations in water. In addition to decreasing dissolved organic carbon concentrations, the effectiveness of iron- and aluminum-based coagulants for decreasing dissolved concentrations both of inorganic and monomethyl mercury in water was demonstrated in laboratory studies that used agricultural drainage water from the Sacramento–San Joaquin Delta of California. To test the effectiveness of this approach at the field scale, nine 15-by-40 ‑ meter wetland cells were constructed on Twitchell Island that received untreated water from island drainage canals (control) or drainage water treated with polyaluminum chloride or ferric sulfate coagulants. Surface-water samples were collected approximately monthly during November 2012–September 2013 from the inlets and outlets of the wetland cells and then analyzed by the U.S. Geological Survey for total concentrations of mercury and monomethyl mercury in filtered (less than 0.3 micrometers) and suspended-particulate fractions and for concentrations of dissolved organic carbon. In the control wetland cells, total mercury concentrations in filtered water samples ranged from 0.94 to 2.47 nanograms per liter (ng/L) at the control inlets and from 0.84 to 2.63 ng/L at the control outlets, and particulate total mercury concentrations in water ranged from 0.27 to 1.49 ng/L at the control inlets and from 0.17 to 1.11 ng/L at the control outlets. Monomethyl mercury concentrations in filtered water ranged from 0.16 to 0.88 ng/L at the control inlets and from 0.13 to 1.30 ng/L at the control outlets; particulate monomethyl mercury concentrations in water ranged from 0.03 to 0.24 ng/L at the control inlets and from 0.03 to 0.23 ng/L at the control outlets. Dissolved organic carbon concentrations in water ranged from 7.9 to 26.7 milligrams per liter at the control inlets and from 8.5 to 28.0 milligrams per liter at the control outlets. Following coagulation, but prior to passage through the wetland cells, coagulation treatments transferred dissolved mercury and carbon to the particulate fraction relative to untreated source water: at the wetland cell inlets, the coagulation treatments decreased concentrations of filtered total mercury by 59–76 percent, filtered monomethyl mercury by 40–70 percent, and dissolved organic carbon by 65–86 percent. Passage through the wetland cells decreased the particulate fraction of mercury in wetland cells that received coagulant-treated water. Changes in total mercury, monomethyl mercury, and dissolved organic carbon concentrations resulting from wetland passage varied both by treatment and season. Despite increased monomethyl mercury in the filtered fraction during wetland passage between March and August, the coagulation-wetland systems generally decreased total mercury (filtered plus particulate) and monomethyl mercury (filtered plus particulate) concentrations relative to source water. Coagulation—either alone or in association with constructed wetlands—could be an effective way to decrease concentrations of mercury and dissolved organic carbon in surface water as well as the bioavailability of mercury in the Sacramento–San Joaquin Delta.

California↗

USGS2015

Females exceed males in mercury concentrations of burbot Lota lota

Examination of differences in contaminant concentrations between sexes of fish, across several fish species, may reveal clues for important behavioral and physiological differences between the sexes. We determined whole-fish total mercury (Hg) concentrations of 25 male and 25 female adult burbot Lota lota captured in Lake Erie during summer 2011, and of 14 male and 18 female adult burbot captured in Great Slave Lake (Northwest Territories, Canada) during winter 2013. On average, females were 22 % greater in Hg concentration than males. This difference was probably not due to a greater feeding rate by females, because results from previous studies based on polychlorinated biphenyl (PCB) determinations of these same burbot indicated that males fed at a substantially greater rate than females. Based on our determinations of Hg concentrations in the gonads and somatic tissue of five ripe females and five ripe males, this difference was not attributable to changes in Hg concentration immediately after spawning due to release of gametes. Further, bioenergetics modeling results from previous studies indicated that growth dilution would not explain any portion of this observed difference in Hg concentrations between the sexes. We, therefore, conclude that this difference was most likely due to a substantially faster rate of Hg elimination by males compared with females. Male burbot exhibit among the greatest gonadosomatic indices (GSIs) of all male fishes, with their testes accounting for between 10 and 15 % of their body weight when the fish are in ripe condition. Androgens have been linked to enhanced Hg elimination rates in other vertebrates. If androgen production is positively related to GSI, then male burbot would be expected to have among the greatest androgen levels of all fishes. Thus, we hypothesize that male burbot eliminate Hg from their bodies faster than most other male fishes, and this explains the greater Hg concentration in females compared with males.

Archives of Environmental Contamination and Toxico↗

USGS2014

Spatial distribution of mercury in southeastern Alaskan streams influenced by glaciers, wetlands, and salmon

Southeastern Alaska is a remote coastal-maritime ecosystem that is experiencing increased deposition of mercury (Hg) as well as rapid glacier loss. Here we present the results of the first reported survey of total and methyl Hg (MeHg) concentrations in regional streams and biota. Overall, streams draining large wetland areas had higher Hg concentrations in water, mayflies, and juvenile salmon than those from glacially-influenced or recently deglaciated watersheds. Filtered MeHg was positively correlated with wetland abundance. Aqueous Hg occurred predominantly in the particulate fraction of glacier streams but in the filtered fraction of wetland-rich streams. Colonization by anadromous salmon in both glacier and wetland-rich streams may be contributing additional marine-derived Hg. The spatial distribution of Hg in the range of streams presented here shows that watersheds are variably, yet fairly predictably, sensitive to atmospheric and marine inputs of Hg.

Alaska↗

USGS2013

Water column and bed-sediment core samples collected from Brownlee Reservoir near Oxbow, Oregon, 2012

The U.S. Geological Survey, in cooperation with Idaho Power Company, collected water-column and bed-sediment core samples from eight sites in Brownlee Reservoir near Oxbow, Oregon, during May 5–7, 2012. Water-column and bed-sediment core samples were collected at each of the eight sites and analyzed for total mercury and methylmercury. Additional bed-sediment core samples, collected from three of the eight sites, were analyzed for pesticides and other organic compounds, trace metals, and physical characteristics, such as particle size. Total mercury and methylmercury were detected in each of the water column and bed-sediment core samples. Only 17 of the 417 unique pesticide and organic compounds were detected in bed-sediment core samples. Concentrations of most organic wastewater compounds detected in bed sediment were less than the reporting level. Trace metals detected were greater than the reporting level in all the bed-sediment core samples submitted for analysis. The particle size distribution of bed-sediment core samples was predominantly clay mixed with silt.

Idaho, Oregon↗

USGS2012

Litterfall mercury dry deposition in the eastern USA

Mercury (Hg) in autumn litterfall from predominately deciduous forests was measured in 3 years of samples from 23 Mercury Deposition Network sites in 15 states across the eastern USA. Annual litterfall Hg dry deposition was significantly higher (median 12.3 micrograms per square meter (μg/m 2 ), range 3.5–23.4 μg/m 2 ) than annual Hg wet deposition (median 9.6 μg/m 2 , range 4.4–19.7 μg/m 2 ). The mean ratio of dry to wet Hg deposition was 1.3–1. The sum of dry and wet Hg deposition averaged 21 μg/m 2 per year and 55% was litterfall dry deposition. Methylmercury was a median 0.8% of Hg in litterfall and ranged from 0.6 to 1.5%. Annual litterfall Hg and wet Hg deposition rates differed significantly and were weakly correlated. Litterfall Hg dry deposition differed among forest-cover types. This study demonstrated how annual litterfall Hg dry deposition rates approximate the lower bound of annual Hg dry fluxes.

Environmental Pollution↗

USGS2012

Sources and sinks of filtered total mercury and concentrations of total mercury of solids and of filtered methylmercury, Sinclair Inlet, Kitsap County, Washington, 2007-10

The majority of filtered total mercury in the marine water of Sinclair Inlet originates from salt water flowing from Puget Sound. About 420 grams of filtered total mercury are added to Sinclair Inlet each year from atmospheric, terrestrial, and sedimentary sources, which has increased filtered total mercury concentrations in Sinclair Inlet (0.33 nanograms per liter) to concentrations greater than those of the Puget Sound (0.2 nanograms per liter). The category with the largest loading of filtered total mercury to Sinclair Inlet included diffusion of porewaters from marine sediment to the water column of Sinclair Inlet and discharge through the largest stormwater drain on the Bremerton naval complex, Bremerton, Washington. However, few data are available to estimate porewater and stormwater releases with any certainty. The release from the stormwater drain does not originate from overland flow of stormwater. Rather total mercury on soils is extracted by the chloride ions in seawater as the stormwater is drained and adjacent soils are flushed with seawater by tidal pumping. Filtered total mercury released by an unknown freshwater mechanism also was observed in the stormwater flowing through this drain. Direct atmospheric deposition on the Sinclair Inlet, freshwater discharge from creek and stormwater basins draining into Sinclair Inlet, and saline discharges from the dry dock sumps of the naval complex are included in the next largest loading category of sources of filtered total mercury. Individual discharges from a municipal wastewater treatment plant and from the industrial steam plant of the naval complex constituted the loading category with the third largest loadings. Stormwater discharge from the shipyard portion of the naval complex and groundwater discharge from the base are included in the loading category with the smallest loading of filtered total mercury. Presently, the origins of the solids depositing to the sediment of Sinclair Inlet are uncertain, and consequently, concentrations of sediments can be qualitatively compared only to total mercury concentrations of solids suspended in the water column. Concentrations of total mercury of suspended solids from creeks, stormwater, and even wastewater effluent discharging into greater Sinclair Inlet were comparable to concentrations of solids suspended in the water column of Sinclair Inlet. Concentrations of total mercury of suspended solids were significantly lower than those of marine bed sediment of Sinclair Inlet; these suspended solids have been shown to settle in Sinclair Inlet. The settling of suspended solids in the greater Sinclair Inlet and in Operable Unit B Marine of the naval complex likely will result in lower concentrations of total mercury in sediments. Such a decrease in total mercury concentrations was observed in the sediment of Operable Unit B Marine in 2010. However, total mercury concentrations of solids discharged from several sources from the Bremerton naval complex were higher than concentrations in sediment collected from Operable Unit B Marine. The combined loading of solids from these sources is small compared to the amount of solids depositing in OU B Marine. However, total mercury concentration in sediment collected at a monitoring station just offshore one of these sources, the largest stormwater drain on the Bremerton naval complex, increased considerably in 2010. Low methylmercury concentrations were detected in groundwater, stormwater, and effluents discharged from the Bremerton naval complex. The highest methylmercury concentrations were measured in the porewaters of highly reducing marine sediment in greater Sinclair Inlet. The marine sediment collected off the largest stormwater drain contained low concentrations of methylmercury in porewater because these sediments were not highly reducing.

Washington↗

USGS2011

Mercury export from the Yukon River Basin and potential response to a changing climate

We measured mercury (Hg) concentrations and calculated export and yield from the Yukon River Basin (YRB) to quantify Hg flux from a large, permafrost-dominated, high-latitude watershed. Exports of Hg averaged 4400 kg Hg yr -1 . The average annual yield for the YRB during the study period was 5.17 μg m -2 yr -1 , which is 3–32 times more than Hg yields reported for 8 other major northern hemisphere river basins. The vast majority (90%) of Hg export is associated with particulates. Half of the annual export of Hg occurred during the spring with about 80% of 34 samples exceeding the U.S. EPA Hg standard for adverse chronic effects to biota. Dissolved and particulate organic carbon exports explained 81% and 50%, respectively, of the variance in Hg exports, and both were significantly ( p < 0.001) correlated with water discharge. Recent measurements indicate that permafrost contains a substantial reservoir of Hg. Consequently, climate warming will likely accelerate the mobilization of Hg from thawing permafrost increasing the export of organic carbon associated Hg and thus potentially exacerbating the production of bioavailable methylmercury from permafrost-dominated northern river basins.

Alaska↗

USGS2008

Total mercury, methylmercury, methylmercury production potential, and ancillary streambed-sediment and pore-water data for selected streams in Oregon, Wisconsin, and Florida, 2003-04

Mercury contamination of aquatic ecosystems is an issue of national concern, affecting both wildlife and human health. Detailed information on mercury cycling and food-web bioaccumulation in stream settings and the factors that control these processes is currently limited. In response, the U.S. Geological Survey (USGS) National Water-Quality Assessment Program (NAWQA) conducted detailed studies from 2002 to 2006 on various media to enhance process-level understanding of mercury contamination, biogeochemical cycling, and trophic transfer. Eight streams were sampled for this study: two streams in Oregon, and three streams each in Wisconsin and Florida. Streambed-sediment and pore-water samples were collected between February 2003 and September 2004. This report summarizes the suite of geochemical and microbial constituents measured, the analytical methods used, and provides the raw data in electronic form for both bed-sediment and pore-water media associated with this study.

Oregon, Wisconsin, Florida↗

USGS2006

Occurrence and distribution of mercury in the surficial aquifer, Long Neck Peninsula, Sussex County, Delaware, 2003–04

In January 2001, mercury (Hg) was detected (500 nanograms per liter, ng/L, or greater) in the distribution system of the Long Neck Water Company (LNWC), Pot Nets, Delaware. By April 2001, two LNWC production wells had been taken off-line because discharge concentrations of total mercury (HgT) either had exceeded or approached the Federal limit of 2,000 ng/L. From October 2003 through January 2005, the U.S. Geological Survey, Delaware Geological Survey, and Delaware Department of Natural Resources and Environmental Control conducted a cooperative study to (a) determine if the Hg contamination was widespread, (b) identify possible forms of Hg in ground water, and (c) examine Hg occurrence in relation to (geo)chemical conditions and characteristics of ground water and sediment in the surficial aquifer on the Long Neck Peninsula, Sussex County, Delaware. An initial water-quality survey conducted with samples from 22 production wells revealed that concentrations of HgT in ground water in the surficial aquifer ranged from 0.11 to 1,820 ng/L. Shallow ground water (less than 120 feet below land surface) throughout most of the peninsula, including that which contained elevated concentrations of HgT (exceeding 100 ng/L), appeared to be affected by human activities. All samples contained volatile organic compounds (VOCs) and elevated nitrate-nitrogen (NO3-N, exceeding 0.4 milligrams per liter, mg/L). Most (16 of 22) samples had elevated specific conductance (SC, in excess of 100 microsiemens per centimeter at 25 degrees Celsius). Elevated concentrations of HgT, however, only occurred in five production wells in the Pot Nets Bayside and Lakeside communities. The vertical distribution of HgT in shallow ground water (less than 80 feet below land surface) was determined with samples collected at 5 to 6 vertical-nest short-screened (2 - 5-foot length) monitoring wells installed near Bayside and Lakeside production wells with the highest HgT concentrations (exceeding 1,000 ng/L). Elevated concentrations ofHgT (100-6,380 ng/L) occurred in the shallow aquifer near each well at different depths. Chemical analyses of selected soil, fill, and aquifer sediment samples, obtained during the installation of nested wells, indicated that little HgT occurred in soil or fill at either site (40 micrograms per kilogram, ?g/kg, or less). No HgT was detected (less than 20 ?g/kg) in aquifer sediment samples. These low HgT concentrations imply that neither the soil, fill, nor aquifer sediment was a likely source of the elevated Hg in ground water. Given Hg occurrence appeared to be a ground-water transport phenomenon, the forms of Hg in transport were investigated. Differences in HgT concentrations between raw and filtered (0.1- and (or) 0.4-absolute micrometer pore size) samples from nested wells were random in sign and similar in magnitude to the variability in measuring HgT attributed to field and laboratory methods (? 5-10 percent, for HgT concentrations exceeding 100 ng/L). Thus, Hg transport likely occurred in a dissolved or fine-colloidal nonparticulate phase. Methyl mercury (HgMe) only was detected at low concentrations (0.06 ng/L or less) in nested-well samples with low to moderate concentrations of HgT (less than 366 ng/L). Whether HgMe occurred at similar concentrations in samples with high HgT concentrations was unresolved due to a sample-matrix interference problem. Potential complex forms of Hg were investigated in relation to the occurrence of selected ligands (organic carbon, sulfide, and chloride concentrations) and geochemical conditions (for example, pH and dissolved oxygen concentrations). Only dissolved organic carbon (DOC) appeared directly related to Hg occurrence. Elevated concentrations of HgT and DOC co-occurred in ground water at both Pot Nets sites. The average concentration of DOC was about four times greater in samples from the Pot Nets wells with the highest HgT concentrations (exceeding 1,000 ng/L) than in most Pot Nets o

Delaware↗

USGS2004

Geochemistry of Mercury and other trace elements in fluvial tailings upstream of Daguerre Point Dam, Yuba River, California, August 2001

This study was designed to characterize the particle-size distribution and the concentrations of total mercury (HgT), methylmercury (MeHg), and other constituents in sediments trapped behind Daguerre Point Dam, a 28-foot-high structure on the lower Yuba River in California. The results of the study will assist other agencies in evaluating potential environmental impacts from mobilization of sediments if Daguerre Point Dam is modified or removed to improve the passage of anadromous fish. Methylmercury is of particular concern owing to its toxicity and propensity to bioaccumulate. A limited amount of recent work on hydraulic and dredge tailings in other watersheds has indicated that mercury and MeHg concentrations may be elevated in the fine-grained fractions of placer mining debris, particularly clay and silt. Mercury associated with tailings from placer gold mines is a source of continued contamination in Sierra Nevada watersheds and downstream water bodies, including the Sacramento?San Joaquin Delta and the San Francisco Bay of northern California. Churn drilling was used to recover sediments and heavy minerals at 5-foot intervals from six locations upstream of Daguerre Point Dam. Maximum depth of penetration ranged from 17.5 to 35 feet below land surface, resulting in 31 discreet drilled intervals. Drilling in permeable, unconsolidated sediments below the streambed of the Yuba River released a significant volume of water along with the sediment, which complicated the sampling and characterization effort. Overflow of a silty fraction sampled at the drill site contained suspended sediment consisting predominantly of silt and clay, with HgT concentration ranging from 33 to 1,100 ng/g (nanogram per gram) dry weight. A sandy fraction, collected after sieving sediment through a 2-millimeter vibratory screen, contained from 14 to 82 percent sand and 1 to 29 percent silt plus clay, and had HgT concentrations ranging from 6.8 to 81 ng/g dry weight. A clay-silt fraction, sampled from material remaining in suspension after the sandy fraction settled for 15-20 minutes, contained mercury concentrations from 23 to 370 ng/g dry weight. Concentrations of MeHg were less than the detection limit (<0.001 ng/g dry weight) in 30 of 31 samples of the sandy fraction. In the suspended clay-silt fraction, MeHg was detected in 16 of 31 samples, in which it ranged in concentration from 0.04 (estimated) to 0.61 ng/g wet weight. Potential rates of mercury methylation and demethylation were evaluated in seven samples using radiotracer methods. Mercury methylation (MeHg production) potentials were generally low, ranging from less than 0.15 to about 1.6 ng/g/d (nanogram per gram of dry sediment per day). Mercury demethylation (MeHg degradation) potentials were moderately high, ranging from 1.0 to 2.2 ng/g/d. The ratio of methylation potential (MP) to demethylation potential (DP) ranged from less than 0.14 to about 1.4 (median = 0.24, mean = 0.44, number of samples = 7), suggesting that the potential for net production of MeHg in deep sediments is generally low. The MeHg production rates and MP/DP ratios were higher in the shallower interval in two of the three holes where two depth intervals were assessed, whereas the MeHg concentrations were higher in the shallower interval for all three holes. A similar spatial distribution was found for concentrations of solid-phase sulfide (measured as total reduced sulfur and likely representing iron-sulfide and iron-disulfide compounds), which were much higher in shallower samples (about 700 to about 2,100 nanomoles per gram, dry sediment) than in deeper samples (32 to 55 nanomoles per gram, dry sediment) in these three holes. If reduced sulfur compounds are oxidized to sulfate as a consequence of sediment disturbance, the activity of sulfate-reducing bacteria might be stimulated, causing a short-term increase in methylation of inorganic Hg(II) (divalent mercury).

California↗

USGS2004

Methods for the preparation and analysis of solids and suspended solids for methylmercury

This report presents the methods and method performance data for the determination of methylmercury concentrations in solids and suspended solids. Using the methods outlined here, the U.S. Geological Survey's Wisconsin District Mercury Laboratory can consistently detect methylmercury in solids and suspended solids at environmentally relevant concentrations. Solids can be analyzed wet or freeze dried with a minimum detection limit of 0.08 ng/g (as-processed). Suspended solids must first be isolated from aqueous matrices by filtration. The minimum detection limit for suspended solids is 0.01 ng per filter resulting in a minimum reporting limit ranging from 0.2 ng/L for a 0.05 L filtered volume to 0.01 ng/L for a 1.0 L filtered volume. Maximum concentrations for both matrices can be extended to cover nearly any amount of methylmercury by limiting sample size.

Techniques and Methods↗

USGS2004

Methods for the preparation and analysis of solids and suspended solids for total mercury

The methods documented in this report are utilized by the Wisconsin District Mercury Lab for analysis of total mercury in solids (soils and sediments) and suspended solids (isolated on filters). Separate procedures are required for the different sample types. For solids, samples are prepared by room-temperature acid digestion and oxidation with aqua regia. The samples are brought up to volume with a 5 percent bromine monochloride solution to ensure complete oxidation and heated at 50C in an oven overnight. Samples are then analyzed with an automated flow injection system incorporating a cold vapor atomic fluorescence spectrometer. A method detection limit of 0.3 ng of mercury per digestion bomb was established using multiple analyses of an environmental sample. Based on the range of masses processed, the minimum sample reporting limit varies from 0.6 ng/g to 6 ng/g. Suspended solids samples are oxidized with a 5 percent bromine monochloride solution and held at 50?C in an oven for 5 days. The samples are then analyzed with an automated flow injection system incorporating a cold vapor atomic fluorescence spectrometer. Using a certified reference material as a surrogate for an environmental sample, a method detection limit of 0.059 ng of mercury per filter was established. The minimum sample reporting limit varies from 0.059 ng/L to 1.18 ng/L, depending on the volume of water filtered.

Techniques and Methods↗

USGS2002

Atmospheric mercury deposition during the last 270 years: A glacial ice core record of natural and anthropogenic sources

Mercury (Hg) contamination of aquatic ecosystems and subsequent methylmercury bioaccumulation are significant environmental problems of global extent. At regional to global scales, the primary mechanism of Hg contamination is atmospheric Hg transport. Thus, a better understanding of the long-term history of atmospheric Hg cycling and quantification of the sources is critical for assessing the regional and global impact of anthropogenic Hg emissions. Ice cores collected from the Upper Fremont Glacier (UFG), Wyoming, contain a high-resolution record of total atmospheric Hg deposition (ca. 1720−1993). Total Hg in 97 ice-core samples was determined with trace-metal clean handling methods and low-level analytical procedures to reconstruct the first and most comprehensive atmospheric Hg deposition record of its kind yet available from North America. The record indicates major atmospheric releases of both natural and anthropogenic Hg from regional and global sources. Integrated over the past 270-year ice-core history, anthropogenic inputs contributed 52%, volcanic events 6%, and background sources 42%. More significantly, during the last 100 years, anthropogenic sources contributed 70% of the total Hg input. Unlike the 2−7-fold increase observed from preindustrial times (before 1840) to the mid-1980s in sediment-core records, the UFG record indicates a 20-fold increase for the same period. The sediment-core records, however, are in agreement with the last 10 years of this ice-core record, indicating declines in atmospheric Hg deposition.

Environmental Science & Technology↗

USGS2002

Mercury loading and methylmercury production and cycling in high-altitude lakes from the Western United States

Studies worldwide have shown that mercury (Hg) is a ubiquitous contaminant, reaching even the most remote environments such as high-altitude lakes via atmospheric pathways. However, very few studies have been conducted to assess Hg contamination levels of these systems. We sampled 90 mid-latitude, high-altitude lakes from seven national parks in the western United States during a four-week period in September 1999. In addition to the synoptic survey, routine monitoring and experimental studies were conducted at one of the lakes (Mills Lake) to quantify MeHg fluxrates and important process rates such as photo-demethylation. Results show that overall, high-altitude lakes have low total mercury (HgT) and methylmercury (MeHg) levels (1.07 and 0.05 ng L -1 , respectively), but a very good correlation of Hg to MeHg (r 2 = 0.82) suggests inorganic Hg(II) loading is a primary controlling factor of MeHg levels in dilute mountain lakes. Positive correlations were also observed for dissolved organic carbon (DOC) and both Hg and MeHg, although to a much lesser degree. Levels of MeHg were similar among the seven national parks, with the exception of Glacier National Park where lowerconcentrations were observed (0.02 ng L -1 ), and appear to be related to naturally elevated pH values there. Measured rates ofMeHg photo-degradation at Mills Lake were quite fast, and this process was of equal importance to sedimentation and stream flow for removing MeHg. Enhanced rates of photo-demethylation are likely an important reason why high-altitude lakes, with typically high water clarity and sunlight exposure, are low in MeHg.

California, Colorado, Montana, Wyoming↗

USGS1995

Radon-222 concentrations in ground water and soil gas on Indian reservations in Wisconsin

The weighted average radon-222 concentration of indoor air in homes located on Wisconsin Indian Reservations is 5.8 picocuries per liter, which exceeds the U.S. Environmental Protection Agency action limit of 4 picocuries per liter. Ground water is the principle source of drinking water on Wisconsin Indian Reservations and generally accounts for about 5 percent of the total indoor air radon-222 concentrations found in homes. To determine the distribution of radon-222, ground water from 29 private and community Wisconsin Indian Reservation wells and soil gas at a depth of about 3 feet below land surface adjacent to the wells were sampled. Sites with wells were distributed among the 11 Wisconsin Indian Reservations so that each Reservation contained at least 2 sites. The remaining seven sites were divided among the Reservation by acreage held by each tribe. Ground-water samples were collected using a syringe technique after the wells had been purged sufficiently to reach chemical stability. Samples were then sent by overnight mail to the U.S. Geological Survey, National Water Quality Lab for analysis by liquid scintillation counting. Soil gas was collected in Lucas cells, using a small-diameter soil probe and peristaltic pump. The cells were then analyzed by Lucas cell alpha scintillation counting with a portable radon detector. The highest radon-222 concentrations in ground water and soil gas are from sites with wells finished in the crystalline bedrock aquifer. Radon-222 concentrations in 29 ground-water samples collected from the sand and gravel and sedimentary and crystalline bedrock aquifers range from 260 to 22,000 picocuries per liter with a median concentration of 560 picocuries per liter. Only 2 of the 29 ground-water samples have radon-222 concentrations less than the U.S. Environmental Protection Agency proposed standard of 300 picocuries per liter. The highest radon-222 concentrations were found in ground water from wells in Shawano, Menominee, Forest, and Marathon counties. Radon-222 concentrations in soil gas range from 130 to 7,810 picocuries per liter with a median concentration of 560 picocuries per liter. For sites with wells finished in the sand and gravel aquifer, the coefficient of determination (R2) of the regression of concentration of radon-222 in ground water as a function of well depth is 0.003 and the significance level is 0.32, which indicates that there is not a statistically significant relation between radon-222 concentrations in ground water and well depth. The coefficient of determination of the regression of radon-222 in ground water and soil gas is 0.19 and the root mean square error of the regression line is 271 picocuries per liter. Even though the significance level (0.036) indicates a statistical relation, the root mean square error of the regression is so large that the regression equation would not give reliable predictions. Because of an inadequate number of samples, similar statistical analyses could not be performed for sites with wells finished in the crystalline and sedimentary bedrock aquifers.

Wisconsin↗