Geology topics

Jennifer B. Sharpe

Publications and source records attributed to Jennifer B. Sharpe.

At least 19 recordsLinked to original sources

USGS2024

Simulation of groundwater and surface-water interaction and lake resiliency at Crystal Lake, City of Crystal Lake, Illinois

The U.S. Geological Survey, in cooperation with the City of Crystal Lake, Illinois, started a study to increase understanding of groundwater and surface-water interaction between the glacial aquifer and the city’s namesake lake, Crystal Lake, and the effect of higher and lower precipitation conditions on groundwater and lake levels. The results from this study could be used by the city and others to aid in lake management strategies. This report describes the hydrologic lake budget and each of the budget components, which are then used in the construction, calibration, and application of a regional groundwater flow model. The flow model is used to simulate the shallow groundwater flow system and the lake responses to increased and decreased precipitation under the current weir elevation and the proposed lowered weir elevation. Using the program groundwater flow analytic element model (GFLOW), a two-dimensional, steady-state model was constructed. The model was calibrated by matching target water levels and stream base flows by adjusting model input parameters. A sensitivity analysis was completed by adjusting the parameters within reasonable ranges and noting the magnitude of changes in model calibration targets. Potential effects of extended wet and dry periods (within historical ranges and published predicted ranges) were evaluated by adjusting precipitation, groundwater recharge, and discharge at Crystal Lake culvert outlet in the model and comparing the resulting simulated lake stage and water budgets to stages and water budgets from the calibrated model. Model results under average, wet, and dry conditions with a lowered weir of 1 foot at the Crystal Lake culvert outlet indicate minor changes in the simulated lake-water budgets and associated lake levels and groundwater elevation contours; however, simulations with an increased outflow at the Crystal Lake culvert outlet decreased the lake water levels by as much as 1.87 feet and also decreased the groundwater levels surrounding the lake by about 1–2 feet during average and wet conditions.

Illinois↗

USGS2023

Statewide sampling to determine spatial distribution, prevalence, and occurrence of per- and polyfluoroalkyl substances (PFAS) in Illinois community water supplies, 2020–21

Per- and polyfluoroalkyl substances (PFAS) are a group of synthetic chemicals that have been manufactured and used globally since the 1940s. PFAS are used for their oil- and water-repellent properties, ability to reduce friction, and their flame-retardant nature. PFAS are widely used in a variety of products, including clothing, carpet, food packaging, and firefighting foam. The properties that make them useful in manufacturing, however, also make them persistent and mobile, causing potential exposures to the environment and humans. Known as “forever chemicals,” these compounds resist degradation and have been determined to bioaccumulate in humans and wildlife. The Illinois Environmental Protection Agency (IEPA) collected a total of 1,711 samples (includes quality-control samples) of finished water at 1,428 entry points from 1,017 Illinois community water supply (CWS) systems and analyzed the water samples for PFAS. The results following confirmation samples indicated a mean of 99 percent of all sample results were below the minimum reporting level (MRL) of 2 nanograms per liter (ng/L). Of the detections at or above the MRL, 7 of 18 PFAS were detected in 149 of 1,428 entry points (about 10 percent). Of the nearly 7.4 million residents directly served by the CWS systems sampled, more than 1.3 million residents (about 18 percent) are served by CWS systems that had at least one detection of PFAS above the MRL of 2 ng/L. The most frequently detected PFAS were perfluorobutanesulfonic acid (about 6.2 percent, 37 ng/L maximum concentration), perfluorooctanesulfonic acid (PFOS) (about 5.0 percent, 150 ng/L maximum concentration), and perfluorooctanoic acid (PFOA) (about 4.8 percent, 25 ng/L maximum concentration). Of the 1,428 entry point samples from the CWS systems, 149 samples had confirmed detections of PFAS, with 93 of those 149 (about 62 percent) samples having at least one PFAS with a concentration that exceeded the median detected concentration of 3.2 ng/L. The highest concentrations detected were 150 ng/L (PFOS) and 140 ng/L (perfluorohexanesulfonic acid) at one CWS location which has been shut down and a different source of water has been provided to the consumers. Although PFAS detections were more common in CWS systems using surface-water sources (about 35 percent, 30 of 85) and mixed sources (50 percent, 5 of 10) compared to those using groundwater sources (about 9 percent, 114 of 1,333), a greater range of PFAS concentrations were observed in groundwater CWS systems (2 to 150 ng/L) than in surface-water CWS systems (2 to 15 ng/L). Statistically significant differences were determined between some detected PFAS (PFOA, PFOS, and perfluorohexanoic acid) and the source of drinking water (groundwater, surface water, or mixed). This report summarizes the occurrence and spatial distribution of PFAS in CWS systems across Illinois. The results from this sampling effort could be used by Illinois public health officials to identify the potential risk of PFAS in drinking water to human health.

Illinois↗

USGS2023

Estimating peak-flow quantiles for selected annual exceedance probabilities in Illinois

This report presents the methods, results, and applications of an updated flood-frequency study for the State of Illinois. This study, which uses data through September 2017, updates two previous studies that used data through 1999 and 2009, respectively. Flood-frequency estimates are used for a variety of land-use planning and infrastructure design purposes, including for the hydraulic design of bridges. The flood frequencies presented are the stream discharges (or quantiles) that are exceeded each year with a given probability, called the annual exceedance probability (AEP). Estimates are provided for eight AEPs: 0.5, 0.2, 0.1, 0.04, 0.02, 0.01, 0.005, and 0.002. The basic data used are the annual maximum discharges (peak flows) at streamgages in and near Illinois and the measurable physical properties (basin characteristics) of the basins upstream from those streamgages. The logarithms of the peak flow records at qualifying streamgages were fit to the Pearson Type 3 distribution using federally recommended methods, providing one of the two primary products of the study, which is the set of peak-flow quantiles at the streamgages and their uncertainties. The other primary product is sets of equations, determined by least-squares regression, that relate the peak-flow quantiles and the basin characteristics. There is one set of equations for each of Illinois’ seven hydrologic regions, and, for each region, one equation for each AEP. These regional equations allow the estimation of peak-flow quantiles at ungaged locations throughout the state and their uncertainties. A set of illustrative example applications is provided, and tables of all results at all study streamgages and regions are provided in associated data releases. The study results are also being made available in a web application, StreamStats.

Illinios↗

USGS2022

Predicted uranium and radon concentrations in New Hampshire (USA) groundwater—Using Multi Order Hydrologic Position as predictors

Two radioactive elements, uranium (U) and radon (Rn), which are of potential concern in New Hampshire (NH) groundwater, are investigated. Exceedance probability maps are tools to highlight locations where the concentrations of undesirable substances in the groundwater may be elevated. Two forms of statistical analysis are used to create exceedance probability maps for U and Rn in NH groundwater. The first, Boosted Regression Tree (BRT), was selected for estimating U exceedance values. It computes exceedance values directly using the Bernoulli distribution function. The second method of statistical analysis used for Rn to determine exceedance probabilities is ordinary least squares (OLS) regression. In the process of determining exceedance probabilities for U and Rn, the utility of a new dataset is investigated. That new predictor dataset is the Multi-Order Hydrologic Position (MOHP) dataset. MOHP raster datasets have been produced nationally for the conterminous United States at a 30-m resolution. The concept behind MOHP is that, for any given point on the earth's surface, there is the potential for a longer groundwater flow path as one goes deeper beneath the land surface. MOHP predictors were tested in both models. Three MOHP predictors were found useful in the BRT model and two in the OLS model. MOHP data were found useful as predictors along with other site characteristics in predicting U and Rn exceedance probabilities in New Hampshire groundwater.

New Hampshire↗

USGS2019

Multiorder hydrologic position in the conterminous United States: A set of metrics in support of groundwater mapping at regional and national scales

The location of a point on the landscape within a stream network (hydrologic position) can be an important predictive measure in hydrology. Hydrologic position is defined here by two metrics: lateral position and distance from stream to divide, both measured horizontally. Lateral position (dimensionless) is the relative position of a point between the stream and its watershed divide. Distance from stream to divide (units of length) is an indicator of position within a watershed: generally small near a confluence and generally large in headwater areas. Watersheds and watershed divides are defined here by Thiessen polygons rather than topographic divides. Lateral position and distance from stream to divide are also defined in the context of hydrologic order. Hydrologic order “ n ” is defined as the network of streams, and associated divides, of order n and higher. And given that a point can have different positions in different hydrologic orders the term multiorder hydrologic position (MOHP) is used to describe the ensemble of hydrologic positions. MOHP was mapped across the conterminous United States for nine hydrologic orders at a spatial resolution of 30 m (about 8.7 billion pixels). There are 18 metrics for each pixel. Four case studies are presented that use MOHP metrics as explanatory factors in random forest machine learning models. The case studies show that lower order MOHP metrics can serve as indicators of hydrologic process while higher‐order metrics serve as indicators of location. MOHP is shown to have utility as a predictor variable across a large range of scales (50,000 to 8,000,000 km 2 ).

Water Resources Research↗

USGS2019

Bathymetric map and surface area and capacity table for Beaver Lake near Rogers, Arkansas, 2018

Beaver Lake was constructed in 1966 on the White River in the northwest corner of Arkansas for flood control, hydroelectric power, public water supply, and recreation. The surface area of Beaver Lake is about 27,900 acres and approximately 449 miles of shoreline are at the conservation pool level (1,120 feet above the North American Vertical Datum of 1988). Sedimentation in reservoirs can result in reduced water storage capacity and a reduction in usable aquatic habitat. Therefore, accurate and up-to-date estimates of reservoir water capacity are important for managing pool levels, power generation, recreation, and downstream aquatic habitat. Many of the lakes operated by the U.S. Army Corps of Engineers are periodically surveyed to monitor bathymetric changes that affect water capacity. In October 2018, the U.S. Geological Survey, in cooperation with the U.S. Army Corps of Engineers, completed one such survey of Beaver Lake using a multibeam echosounder. The echosounder data were combined with light detection and ranging (lidar) data to prepare a bathymetric map and a surface area and capacity table.

Arkansas↗

USGS2018

Secondary hydrogeologic regions of the conterminous United States

The U.S. Geological Survey (USGS) previously identified and mapped 62 Principal Aquifers (PAs) in the U.S., with 57 located in the conterminous states. Areas outside of PAs, which account for about 40% of the conterminous U.S., were collectively identified as “other rocks.” This paper, for the first time, subdivides this large area into internally-consistent features, defined here as Secondary Hydrogeologic Regions (SHRs). SHRs are areas of other rock within which the rocks or deposits are of comparable age, lithology, geologic or physiographic setting, and relationship to the presence or absence of underling PAs or overlying glacial deposits. A total of 69 SHRs were identified. The number and size of SHRs identified in this paper are comparable to the number and size of PAs previously identified by the USGS. From a two-dimensional perspective, SHRs are complementary to PAs, mapped only where the PAs were not identified on the USGS PA map and not mapped where the PAs were identified. SHRs generally consist of low permeability rocks or deposits, but can include locally productive aquifers. The two maps, taken together, provide a comprehensive, national-scale hydrogeologic framework for assessing and understanding groundwater systems.

Groundwater↗

USGS2016

Estimation of peak discharge quantiles for selected annual exceedance probabilities in northeastern Illinois

This report provides two sets of equations for estimating peak discharge quantiles at annual exceedance probabilities (AEPs) of 0.50, 0.20, 0.10, 0.04, 0.02, 0.01, 0.005, and 0.002 (recurrence intervals of 2, 5, 10, 25, 50, 100, 200, and 500 years, respectively) for watersheds in Illinois based on annual maximum peak discharge data from 117 watersheds in and near northeastern Illinois. One set of equations was developed through a temporal analysis with a two-step least squares-quantile regression technique that measures the average effect of changes in the urbanization of the watersheds used in the study. The resulting equations can be used to adjust rural peak discharge quantiles for the effect of urbanization, and in this study the equations also were used to adjust the annual maximum peak discharges from the study watersheds to 2010 urbanization conditions. The other set of equations was developed by a spatial analysis. This analysis used generalized least-squares regression to fit the peak discharge quantiles computed from the urbanization-adjusted annual maximum peak discharges from the study watersheds to drainage-basin characteristics. The peak discharge quantiles were computed by using the Expected Moments Algorithm following the removal of potentially influential low floods defined by a multiple Grubbs-Beck test. To improve the quantile estimates, regional skew coefficients were obtained from a newly developed regional skew model in which the skew increases with the urbanized land use fraction. The skew coefficient values for each streamgage were then computed as the variance-weighted average of at-site and regional skew coefficients. The drainage-basin characteristics used as explanatory variables in the spatial analysis include drainage area, the fraction of developed land, the fraction of land with poorly drained soils or likely water, and the basin slope estimated as the ratio of the basin relief to basin perimeter. This report also provides the following: (1) examples to illustrate the use of the spatial and urbanization-adjustment equations for estimating peak discharge quantiles at ungaged sites and to improve flood-quantile estimates at and near a gaged site; (2) the urbanization-adjusted annual maximum peak discharges and peak discharge quantile estimates at streamgages from 181 watersheds including the 117 study watersheds and 64 additional watersheds in the study region that were originally considered for use in the study but later deemed to be redundant. The urbanization-adjustment equations, spatial regression equations, and peak discharge quantile estimates developed in this study will be made available in the web application StreamStats, which provides automated regression-equation solutions for user-selected stream locations. Figures and tables comparing the observed and urbanization-adjusted annual maximum peak discharge records by streamgage are provided at https://doi.org/10.3133/sir20165050 for download.

Illinois↗

USGS2015

Lake Michigan Diversion Accounting land cover change estimation by use of the National Land Cover Dataset and raingage network partitioning analysis

The U.S. Army Corps of Engineers (USACE), Chicago District, is responsible for monitoring and computation of the quantity of Lake Michigan water diverted by the State of Illinois. As part of this effort, the USACE uses the Hydrological Simulation Program–FORTRAN (HSPF) with measured meteorological data inputs to estimate runoff from the Lake Michigan diversion special contributing areas (SCAs), the North Branch Chicago River above Niles and the Little Calumet River above South Holland gaged basins, and the Lower Des Plaines and the Calumet ungaged that historically drained to Lake Michigan. These simulated runoffs are used for estimating the total runoff component from the diverted Lake Michigan watershed, which is accountable to the total diversion by the State of Illinois. The runoff is simulated from three interpreted land cover types in the HSPF models: impervious, grass, and forest. The three land cover data types currently in use were derived from aerial photographs acquired in the early 1990s. This study used the National Land Cover Dataset (NLCD) and developed an automated process for determining the area of the three land cover types, thereby allowing faster updating of future models, and for evaluating land cover changes by use of historical NLCD datasets. The study also carried out a raingage partitioning analysis so that the segmentation of land cover and rainfall in each modeled unit is directly applicable to the HSPF modeling. Historical and existing impervious, grass, and forest land acreages partitioned by percentages covered by two sets of raingages for the Lake Michigan diversion SCAs, gaged basins, and ungaged basins are presented.

Illinois↗

USGS2015

Bathymetric survey of Lake Calumet, Cook County, Illinois

The U.S. Geological Survey collected bathymetric data in Lake Calumet and a portion of the Calumet River in the vicinity of Lake Calumet to produce a bathymetric map. The bathymetric survey was made over 3 days (July 26, September 11, and November 7, 2012). Lake Calumet has become a focus area for Asian carp rapid-response efforts by state and federal agencies, and very little bathymetric data existed prior to this survey. This bathymetric survey provides data for a variety of scientific and engineering studies of the area; for example, hydraulic modeling of water and sediment transport from Lake Calumet to the Calumet River.

Illinois↗

USGS2014

Estimation of regional flow-duration curves for Indiana and Illinois

Flow-duration curves (FDCs) of daily streamflow are useful for many applications in water resources planning and management but must be estimated at ungaged sites. One common technique for estimating FDCs at ungaged sites in a given region is to use equations obtained by linear regression of FDC quantiles against multiple basin characteristics that can be computed by means of a geographic information system (GIS) computer program. In this study, such regional regression equations for estimating FDC quantiles were computed at the 0.1, 0.2, 0.5, 1, 2, 5, 10, 20, 25, 30, 40, 50, 60, 70, 75, 80, 90, 95, 98, 99, 99.5, 99.8, and 99.9-percent exceedance probabilities for rural, unregulated streams in Indiana and Illinois with temporally stationary records, using data through September 30, 2007. The approach used accounts for censored values below 0.01 cubic feet per second, which are observed at exceedance probabilities as low as 70 percent (that is, occurring at least 30 percent of the time). The basin characteristics used are suitable for computation by the USGS Web-based application, StreamStats, and are available for all U.S. Environmental Protection Agency (EPA) Region V states and the larger Great Lakes area, with some specific local exceptions. Indiana and Illinois were each divided into three regions, and a different set of equations for estimating FDC quantiles was computed for each region. The error of estimation of the FDC quantiles, measured as the mean square residual in log space converted to a percentage of the quantile, varies somewhat among regions and varies strongly with exceedance probability, with a minimum error of 10 to 20 percent at an exceedance probability of 5 or 10 percent, but rises to 17 to 38 percent at the high-flow end of the FDCs (the 0.1-percent quantile) and 100 to 745 percent at the low-flow end. For comparison, errors of estimation also were computed for FDC quantiles estimated by linear regression on drainage area alone and by using the drainage-area ratio (DAR) method. Three criteria, the nearest basin centroid and two others termed “strict” and “broad”, were used to select index stations for the DAR method. The “strict” and “broad” criteria put conditions on the basin centroid distance and the range of their drainage-area ratios, and the errors were averaged for all index station pairs satisfying each criterion. The use of the simpler DAR method usually resulted in higher errors of estimation compared to the linear regression equations with multiple basin characteristics, except occasionally in the case of the DAR method with the strict index station selection criterion, a criterion that is rarely possible to satisfy in practice. An example application of the estimated equations to one gaged and a few ungaged locations in a watershed in the study area is included to illustrate the steps required. These steps are the computation of the basin characteristics and, using those characteristics together with the estimated equations, the computation of the FDC quantiles and their uncertainties.

Illinois, Indiana↗

USGS2013

Flood-inundation maps for the DuPage River from Plainfield to Shorewood, Illinois, 2013

Digital flood-inundation maps for a 15.5-mi reach of the DuPage River from Plainfield to Shorewood, Illinois, were created by the U.S. Geological Survey (USGS) in cooperation with the Will County Stormwater Management Planning Committee. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/ depict estimates of the areal extent of flooding corresponding to selected water levels (gage heights or stages) at the USGS streamgage at DuPage River at Shorewood, Illinois (sta. no. 05540500). Current conditions at the USGS streamgage may be obtained on the Internet at http://waterdata.usgs.gov/usa/nwis/uv?05540500. In addition, the information has been provided to the National Weather Service (NWS) for incorporation into their Advanced Hydrologic Prediction Service (AHPS) flood warning system (http://water.weather.gov/ahps/). The NWS forecasts flood hydrographs at many places that are often colocated with USGS streamgages. The NWS-forecasted peak-stage information, also shown on the DuPage River at Shorewood inundation Web site, may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. In this study, flood profiles were computed for the stream reach by means of a one-dimensional step-backwater model. The hydraulic model was then used to determine nine water-surface profiles for flood stages at 1-ft intervals referenced to the streamgage datum and ranging from NWS Action stage of 6 ft to the historic crest of 14.0 ft. The simulated water-surface profiles were then combined with a Digital Elevation Model (DEM) (derived from Light Detection And Ranging (LiDAR) data) by using a Geographic Information System (GIS) in order to delineate the area flooded at each water level. These maps, along with information on the Internet regarding current gage height from USGS streamgages and forecasted stream stages from the NWS, provide emergency management personnel and residents with information that is critical for flood response activities such as evacuations and road closures, as well as for postflood recovery efforts.

Illinois↗

USGS2012

Flood of September 13-16, 2008, in northeastern Illinois

Major flooding occurred in northeastern Illinois during September 13–16, 2008, following extended storm activity. Rainfall recorded at select Illinois State Water Survey (ISWS), National Weather Service (NWS), and U.S. Geological Survey (USGS) rain gages in northeastern Illinois, ranged from 2.39 to 10.51 inches throughout a 51-hour period during September 12–14, 2008. The rainfall resulted in extensive urban drainage and riverine flooding, causing the evacuation of thousands of residents, millions of dollars in damages, hundreds of road closings, and two water-related fatalities in the greater Chicago area. Nine counties in northeastern Illinois (16 counties throughout the State) were declared Federal disaster areas. USGS streamgages recorded new record-peak streamflows at 13 locations as a result of the heavy rainfall. Four streamgages had a calculated annual exceedance probability (AEP) ranging from 0.2 to 1 percent, and one streamgage had a calculated AEP of less than 0.2 percent. During this flood event, USGS crews made 48 streamflow measurements at 45 streamgages. After the high-water had subsided, USGS crews set 230 high-water marks in over 40 communities along 131 miles of streams. The elevations for 117 high-water marks along approximately 100 miles of streams were measured by the Metropolitan Water Reclamation District of Greater Chicago (MWRDGC) and the Illinois Department of Natural Resources–Office of Water Resources (IDNR–OWR). Flood peak water-surface profiles for select streams are plotted from the high-water mark data.

Illinois↗

USGS2012

Fecal-indicator bacteria concentrations in the Illinois River between Hennepin and Peoria, Illinois: 2007-08

The Illinois Environmental Protection Agency has designated portions of the Illinois River in Peoria, Woodford, and Tazewell Counties, Illinois, as impaired owing to the presence of fecal coliform bacteria. The U.S. Geological Survey, in cooperation with the Tri-County Regional Planning Commission, examined the water quality in the Illinois River and major tributaries within a 47-mile reach between Peoria and Hennepin, Ill., during water year 2008 (October 2007–September 2008). Investigations included synoptic (snapshot) sampling at multiple locations in a 1-day period: once in October 2007 during lower streamflow conditions, and again in June 2008 during higher streamflow conditions. Five locations in the study area were monitored for the entire year at monthly or more frequent intervals. Two indicator bacteria were analyzed in each water sample: fecal coliform and Escherichia coli ( E. coli ). Streamflow information from previously established monitoring locations in the study area was used in the analysis. Correlation analyses were used to characterize the relation between the two fecal-indicator bacteria and the relation of either indicator to streamflow. Concentrations of the two measured fecal-indicator bacteria correlated well for all samples analyzed (r = 0.94, p <0.001), indicating a strong linear correlation. Presence of one fecal-indicator bacteria generally indicates the presence of another at a similar magnitude and may support substitution of generalized data gaps for other analyses. Hydrologic conditions during the study period can be characterized as wetter than normal, with the mean annual flow in the Illinois River about 37-percent above the long-term average. However, for the Illinois River below Peoria Lake at Peoria, a statistically significant negative correlation coefficient indicates a weak inverse relation between values of streamflow and fecal-indicator bacteria (fecal coliform rho = -0.44, p = 0.0129; E. coli : rho = -0.43, p = 0.0157). The correlation between fecal indicators and streamflow in tributaries or in the Illinois River at Hennepin was found to be statistically significant, yet moderate in strength with coefficient values ranging from r = 0.4 to 0.6. Indirect observations from the June 2008 higher flow synoptic event may indicate continued effects from combined storm and sanitary sewers in the vicinity of the Illinois River near Peoria, Ill., contributing to observed single-sample exceedance of the State criterion for fecal coliform.

Illinois↗

USGS2012

Flood-Inundation Maps for a 1.6-Mile Reach of Salt Creek, Wood Dale, Illinois

Digital flood-inundation maps for a 1.6-mile reach of Salt Creek from upstream of the Chicago, Milwaukee, St. Paul & Pacific Railroad to Elizabeth Drive, Wood Dale, Illinois, were created by the U.S. Geological Survey (USGS) in cooperation with the DuPage County Stormwater Management Division. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/ depict estimates of the areal extent of flooding corresponding to selected water levels (gage heights) at the USGS streamgage on Salt Creek at Wood Dale, Illinois (station number 05531175). Current conditions at the USGS streamgage may be obtained on the Internet at http://waterdata.usgs.gov/usa/nwis/uv?05531175. In this study, flood profiles were computed for the stream reach by means of a one-dimensional unsteady flow Full EQuations (FEQ) model. The unsteady flow model was verified by comparing the rating curve output for a September 2008 flood event to discharge measurements collected at the Salt Creek at Wood Dale gage. The hydraulic model was then used to determine 14 water-surface profiles for gage heights at 0.5-ft intervals referenced to the streamgage datum and ranging from less than bankfull to approximately the highest recorded water level at the streamgage. The simulated water-surface profiles were then combined with a Geographic Information System (GIS) Digital Elevation Model (DEM) (derived from Light Detection and Ranging (LiDAR) data) in order to delineate the area flooded at each water level. The areal extent of the inundation was verified with high-water marks from a flood in July 2010 with a peak gage height of 14.08 ft recorded at the Salt Creek at Wood Dale gage. The availability of these maps along with Internet information regarding current gage height from USGS streamgages provide emergency management personnel and residents with information that is critical for flood response activities such as evacuations and road closures as well as for post-flood recovery efforts.

Illinois↗

USGS2012

Ohio River backwater flood-inundation maps for the Saline and Wabash Rivers in southern Illinois

Digital flood-inundation maps for the Saline and Wabash Rivers referenced to elevations on the Ohio River in southern Illinois were created by the U.S. Geological Survey (USGS). The inundation maps, accessible through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent of flooding corresponding to selected water levels (gage heights) at the USGS streamgage at Ohio River at Old Shawneetown, Illinois-Kentucky (station number 03381700). Current gage height and flow conditions at this USGS streamgage may be obtained on the Internet at http://waterdata.usgs.gov/usa/nwis/uv?03381700. In addition, this streamgage is incorporated into the Advanced Hydrologic Prediction Service (AHPS) flood warning system (http://water.weather.gov/ahps/) by the National Weather Service (NWS). The NWS forecasts flood hydrographs at many places that are often co-located at USGS streamgages. That NWS forecasted peak-stage information, also shown on the Ohio River at Old Shawneetown inundation Web site, may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. In this study, eight water-surface elevations were mapped at 5-foot (ft) intervals referenced to the streamgage datum ranging from just above the NWS Action Stage (31 ft) to above the maximum historical gage height (66 ft). The elevations of the water surfaces were compared to a Digital Elevation Model (DEM) by using a Geographic Information System (GIS) in order to delineate the area flooded at each water level. These maps, along with information on the Internet regarding current gage heights from USGS streamgages and forecasted stream stages from the NWS, provide emergency management personnel and residents with information that is critical for flood response activities such as evacuations and road closures, as well as for post-flood recovery efforts.

Illinois;Kentucky↗

USGS2012

Flood-inundation maps for a nine-mile reach of the Des Plaines River from Riverwoods to Mettawa, Illinois

Digital flood-inundation maps for a 9-mile reach of the Des Plaines River from Riverwoods to Mettawa, Illinois, were created by the U.S. Geological Survey (USGS) in cooperation with the Lake County Stormwater Management Commission and the Villages of Lincolnshire and Riverwoods. The inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science Web site at http://water.usgs.gov/osw/flood_inundation/ , depict estimates of the areal extent of flooding corresponding to selected water levels (gage heights) at the USGS streamgage at Des Plaines River at Lincolnshire, Illinois (station no. 05528100). Current conditions at the USGS streamgage may be obtained on the Internet at http://waterdata.usgs.gov/usa/nwis/uv?05528100 . In addition, this streamgage is incorporated into the Advanced Hydrologic Prediction Service (AHPS) flood warning system ( http://water.weather.gov/ahps/ ) by the National Weather Service (NWS). The NWS forecasts flood hydrographs at many places that are often co-located at USGS streamgages. The NWS forecasted peak-stage information, also shown on the Des Plaines River at Lincolnshire inundation Web site, may be used in conjunction with the maps developed in this study to show predicted areas of flood inundation. In this study, flood profiles were computed for the stream reach by means of a one-dimensional step-backwater model. The hydraulic model was then used to determine seven water-surface profiles for flood stages at roughly 1-ft intervals referenced to the streamgage datum and ranging from the 50- to 0.2-percent annual exceedance probability flows. The simulated water-surface profiles were then combined with a Geographic Information System (GIS) Digital Elevation Model (DEM) (derived from Light Detection And Ranging (LiDAR) data) in order to delineate the area flooded at each water level. These maps, along with information on the Internet regarding current gage height from USGS streamgages and forecasted stream stages from the NWS, provide emergency management personnel and residents with information that is critical for flood response activities such as evacuations and road closures, as well as for post-flood recovery efforts.

Illinois↗

USGS2011

Compilation of watershed models for tributaries to the Great Lakes, United States, as of 2010, and identification of watersheds for future modeling for the Great Lakes Restoration Initiative

As part of the Great Lakes Restoration Initiative (GLRI) during 2009–10, the U.S. Geological Survey (USGS) compiled a list of existing watershed models that had been created for tributaries within the United States that drain to the Great Lakes. Established Federal programs that are overseen by the National Oceanic and Atmospheric Administration (NOAA) and the U.S. Army Corps of Engineers (USACE) are responsible for most of the existing watershed models for specific tributaries. The NOAA Great Lakes Environmental Research Laboratory (GLERL) uses the Large Basin Runoff Model to provide data for the management of water levels in the Great Lakes by estimating United States and Canadian inflows to the Great Lakes from 121 large watersheds. GLERL also simulates streamflows in 34 U.S. watersheds by a grid-based model, the Distributed Large Basin Runoff Model. The NOAA National Weather Service uses the Sacramento Soil Moisture Accounting model to predict flows at river forecast sites. The USACE created or funded the creation of models for at least 30 tributaries to the Great Lakes to better understand sediment erosion, transport, and aggradation processes that affect Federal navigation channels and harbors. Many of the USACE hydrologic models have been coupled with hydrodynamic and sediment-transport models that simulate the processes in the stream and harbor near the mouth of the modeled tributary. Some models either have been applied or have the capability of being applied across the entire Great Lakes Basin; they are (1) the SPAtially Referenced Regressions On Watershed attributes (SPARROW) model, which was developed by the USGS; (2) the High Impact Targeting (HIT) and Digital Watershed models, which were developed by the Institute of Water Research at Michigan State University; (3) the Long-Term Hydrologic Impact Assessment (L–THIA) model, which was developed by researchers at Purdue University; and (4) the Water Erosion Prediction Project (WEPP) model, which was developed by the National Soil Erosion Research Laboratory of the U.S. Department of Agriculture. During 2010, the USGS used the Precipitation-Runoff Modeling System (PRMS) to create a hydrologic model for the Lake Michigan Basin to assess the probable effects of climate change on future groundwater and surface-water resources. The Water Availability Tool for Environmental Resources (WATER) model and the Analysis of Flows In Networks of CHannels (AFINCH) program also were used to support USGS GLRI projects that required estimates of streamflows throughout the Great Lakes Basin. This information on existing watershed models, along with an assessment of geologic, soils, and land-use data across the Great Lakes Basin and the identification of problems that exist in selected tributary watersheds that could be addressed by a watershed model, was used to identify three watersheds in the Great Lakes Basin for future modeling by the USGS. These watersheds are the Kalamazoo River Basin in Michigan, the Tonawanda Creek Basin in New York, and the Bad River Basin in Wisconsin. These candidate watersheds have hydrogeologic, land-type, and soil characteristics that make them distinct from each other, but that are representative of other tributary watersheds within the Great Lakes Basin. These similarities in the characteristics among nearby watersheds will enhance the usefulness of a model by improving the likelihood that parameter values from a previously modeled watershed could reliably be used in the creation of a model of another watershed in the same region. The software program Hydrological Simulation Program–Fortran (HSPF) was selected to simulate the hydrologic, sedimentary, and water-quality processes in these selected watersheds. HSPF is a versatile, process-based, continuous-simulation model that has been used extensively by the scientific community, has the ongoing technical support of the U.S. Environmental Protection Agency and USGS, and provides a means to evaluate the effects that land-use changes or management practices might have on the simulated processes.

Great Lakes Basin↗