Search USGS⌕ Search

Geology topics

James M. Robb

Publications and source records attributed to James M. Robb.

At least 37 records · Page 2Linked to original sources

Simplified method of deep-tow seismic profiling

To improve resolution of seismic-reflection profiles in continental slope water depths of 900 to 1500 m, a single hydrophone was towed about 150 m off the bottom to receive reflected signals from a surface-towed sparker sound source. That deep-towed hydrophone data show that valleys which appear V-shaped in records from a surface-towed hydrophone are flat-bottomed, and that subbottom reflections from an erosional unconformity can be much better resolved. The data produced by this technique are very hepful when used in conjunction with records from conventional surface-towed seismic-profiling equipment.

Geo-Marine Letters↗

Geomorphology and sediment stability of a segment of the U.S. continental slope off New Jersey

The morphology of complex deposits of Pleistocene sediments covering the upper continental slope between Lindenkohl Canyon and South Toms Canyon results from both depositional and erosional processes. Small slump or slide features were detected primarily on the flanks of canyons or valleys and were observed to occur only within Pleistocene-aged sediments. Eocene to Miocene sediments are exposed over much of the mid- and lower slope in this area.

New Jersey↗

Bathymetric map of the continental slope and uppermost continental rise between Lindenkohl Canyon and South Toms Canyon, offshore Eastern United States

This map was prepared as part of a study of geologic hazards to resource exploration and development on the Continental Slope in the Baltimore Canyon Trough area, off southern New Jersey. Detailed bathymetric maps are required for enfineering studies of bottom stability and for geologic interpretation of the nature of the submarine topography. This map presents the morphology of the Continental Slope in greater detail than do other available bathymetic maps (Veatch and Smith, 1939; Uchupi, 1965, sheet 2; U.S. Coast and Geodetic Survey, 1967; Belding and Holland, 1970, sheet 1; National Ocean Survey, 1977).

Lindenkohl Canyon, South Toms Canyon↗

Geology and potential hazards of the continental slope between Lindenkohl and South Toms Canyons, offshore mid-Atlantic United States

Because sediment instability, or slumping, has been identified as a potential hazard to petroleum development of the east-coast Continental Slope, the U.S. Geological Survey, in cooperation with the U.S. Bureau of Land Management, began a detailed study of a segment of the Continental Slope between Lindenkohl and South Toms Canyons off New Jersey. This 40-km x 35-km area was chosen for study because it lies within the area of high interest for petroleum development (Lease sales 49 and 59), and because it includes several wells which provide stratigraphic control. This report discusses the results of geologic mapping, using seismic-reflection data acquired in 1978 and 1979. Some initial results from more recently acquired data are included. The Continental Slope in the study area has a complex surface with ridges, canyons, and valleys. Three slump or slide features were observed in the heads and on the walls of canyons and valleys, and two slides were identified on an intercanyon area. The identified slumps or slides are found in Quaternary sediments and total about 1.3 percent of the Continental Slope area mapped. The slope is generally mantled by less than 2 m of Holocene sediments. Pleistocene sediment (primarily silty clay) is about 450 m thick at the top of the slope and thins to nearly zero or is absent on much of the mid and lower slope, where sediments of Miocene to Eocene age are exposed. Ridges on the midslope (water depths of 800-1,500 m) and parts of the lowr slope (1,500-2,150 m) result primarily from Pleistocene and older deposition. The intervening valleys show evidence of erosion along the deepest parts of their courses. Mid-range sidescan-sonar data show evidence that processes of bottom-current erosion and downcanyon transport of material may be active in the present day. However, major features of the sea floor appear to be unchanged since late-Pleistocene time.

Lindenkohl and South Toms Canyons↗

Evolution of the continental margin of southern Spain and the Alboran Sea

Seismic reflection profiles and magnetic intensity measurements were collected across the southern continental margin of Spain and the Alboran basin between Spain and Africa. Correlation of the distinct seismic stratigraphy observed in the profiles to stratigraphic information obtained from cores at Deep Sea Drilling Project site 121 allows effective dating of tectonic events. The Alboran Sea basin occupies a zone of motion between the African and Iberian lithospheric plates that probably began to form by extension in late Miocene time (Tortonian). At the end of Miocene time (end of Messinian) profiles show that an angular unconformity was cut, and then the strata were block faulted before subsequent deposition. The erosion of the unconformity probably resulted from lowering of Mediterranean sea level by evaporation when the previous channel between the Mediterranean and Atlantic was closed. Continued extension probably caused the block faulting and, eventually the opening of the present channel to the Atlantic through the Strait of Gibraltar and the reflooding of the Mediterranean. Minor tectonic movements at the end of Calabrian time (early Pleistocene) apparently resulted in minor faulting, extensive transgression in southeastern Spain, and major changes in the sedimentary environment of the Alboran basin. Active faulting observed at five locations on seismic profiles seems to form a NNE zone of transcurrent movement across the Alboran Sea. This inferred fault trend is coincident with some bathymetric, magnetic and seismicity trends and colinear with active faults that have been mapped on-shore in Morocco and Spain. The faults were probably caused by stresses related to plate movements, and their direction was modified by inherited fractures in the lithosphere that floors the Alboran Sea.

Alboran Sea↗

Maps showing kinds and sources of environmental geologic and geophysical data collected by the U.S. Geological Survey in the Baltimore Canyon trough area

Exploration for petroleum on the Continental Shelf and Slope off the eastern United States has generated great interest in the quantity and quality of data available to evaluate the nature and magnitude of possible geological enveironmental hazards. This set of maps presents a compilation of publicly available geological and geophysical data acquireed by the U.S. Geological Survey (USGS) in the Baltimore Canyon Trough area of the eastern United States Outer Continental Shelf and Slope. Funding for the collection and analysis of much of the data indicated in this report was provided by the U.S. Bureau of Land Management. Locations of blocks leased for petroleum development and locations of industry wells terminated or being drilled as of February 1980, as well as several other sampling sites, are included for comparison.

Baltimore Canyon Trough↗

Seismic-reflection data on the eastern U.S. continental shelf acquired by M. V. L'OLONNOIS as part of the Atlantic Margin Coring Project (AMCOR) of the U.S. Geological Survey, July-September 1976

In 1976 the U.S. Geological Survey undertook a program to sample the eastern United States Shelf for stratigraphic information by drilling a set of core holes. Results of this Atlantic Margin Coring Program (AMCOR) have been reported by Hathaway and others. Sites were chosen from seismic-reflection data and were reviewed by a safety panel to minimize the risk of penetrating any hydrocarbon accumulation which might lead to environmental contamination. The M-V-L'OLONNOIS, the service ship for the drilling operation, was fitted with seismic-reflection profiling equipment (listed below), to run seismic-reflection profiles before drilling began on each hole. This provided additional assurance that no closed structures would be penetrated and allowed minor adjustment with the site selection. A total of 491 km of high-resolution seismic profiles was collected on 22 sites. Equipment used (specifics for each site noted on records): Bolt Air Guns 1-40 cubic inch chambers EPC Recorder Teledyne Minisparker (last two sites) Navigation used two Internav 101 Loran-C receivers.

Open-File Report↗

High-resolution seismic-reflection profiles collected by the R/V James M. Gilliss, cruise GS 7903-4, in the Baltimore Canyon outer continental shelf area, offshore New Jersey

High-resolution seismic-reflection profiles were collected by the U.S. Geological Survey (USGS) aboard R/V JAMES M. GILLIS (cruise GS 7903-4) from 27 June to 11 July 1979 over the Continental Slope of the Eastern United States between Lindenkohl and Hudson Canyons. These data were acquired as part of a study to determine potential geologic hazards to petroleum development of the Baltimore Canyon trough area. On this cruise, the Continental Slope between Carteret and South Toms Canyons was surveyed along lines spaced one-half nautical mile apart to study the size and distribution of mass-wasting features as a guide to assess the importance of mass-wasting processes on the Continental Slope. The seimsic-reflection profiles were placed to complement other data gathered previously by the USGS and to continue a survey grid begun in 1978 aboard the R/V COLUMBUS !SELIN, cruise CI 7807-1. Track-line distances totaled 1,555 km of 40-in3 air-gun (with wave shaper) profiles, 1, 750 km of 800-J sparker data, and 1,780 km of 3 .5-kHz data. All data are of high quality. A side-scan sonar system was operated briefly along the uppermost Continental Slope to acquire data over 70 km of ship's track. In addition, experimental profiling data were collected from a hydrophone towed at depth over the midslope on the end of the side-scan cable; the surface-towed sparker was used as a sound source. High-resolution profiles were collected by this method over 105 km of track. Navigation was by Loran-C (5-minute fix interval) and satellite. The original data may be inspected at the offices of the U.S. Geological Survey in Woods Hole, Massachusetts 02543. Microfilm copies of the data from this cruise are available for purchase from the National Geophysical and Solar-Terrestrial Data Center (NGSDC), Boulder, Colorado 80303.

Open-File Report↗

High-resolution seismic-reflection profiles collected by the R/V Columbus Iselin, cruise CI 7807-1, in the Baltimore Canyon outer continental shelf area, offshore New Jersey

High-resolution seismic-reflection profiles were collected by the U.S. Geological Survey (USGS) aboard R/V COLUMBUS ISELIN, cruise 7807-1, from 18 August to 4 September 1978 over the Continental Slope of the Eastern United States between Wilmington and Hudson Canyons. These data were acquired as part of a study to determine potential geologic hazards to petroleum development of the Baltimore Canyon trough area. On this cruise, the Continental Slope between Lindenkohl and Carteret Canyons was surveyed along lines spaced one-half nautical mile apart to study the size and distribution of mass-wasting features as a guide to assess the importance of mass wasting processes on the Continental Slope. The seismic-reflection profiles were placed to complement other data gathered previously by the USGS. Track-line distances totaled 2,050 km of 40-in3 air-gun (with wave shaper) profiles, 2,100 km of 800-J sparker data, and 2,100 km of 3 .5-kHz data. The air-gun and sparker profiles are of high quality, but the 3.5-kHz system did not function well and achieved no subbottom penetration. The side-scan sonar system was operated along the uppermost Continental Slope to investigate its potential for use in this environment. Data were acquired over 22 km of ship's track. Navigation was by Loran-C (5-minute fix interval). The original records can be examined at the U.S. Geological Survey offices in Woods Hole, Massachusetts 02543. Microfilm copies of the data are available for purchase from the National Geophysical and Solar-Terrestrial Data Center (NGSDC), Boulder, Colorado 80303.

Open-File Report↗

Summary of regional geology, petroleum potential, resource assessment and environmental considerations for oil and gas lease sale area #56

This report summarizes our general knowledge of the petroleum potential, as well as problems and hazards associated with development of petroleum resources in the area proposed for nominations for lease sale number 56. This area includes the U.S. eastern continental margin from the North Carolina-Virginia border south to approximately Cape Canaveral, Florida and from three miles from shore, seaward to include the upper Continental Slope and inner Blake Plateau. The area for possible sales is shown in figure 1; major physiographic features of the region are shown in figure 2. No wells have been drilled for petroleum within this proposed lease area and no significant commercial production has been obtained onshore in the Southeast Georgia Embayment. The COST GE-1 stratigraphic test well, drilled on the Continental Shelf off Jacksonville, Fla. (fig- 1), reached basement at 3,300 m. The bottom third of the section consists of dominantly continental rocks that are typically poor sources of petroleum (Scholle, 1979) and the rocks that contain organic carbon adequate for generation of petroleum at the well are seen in seismic profiles always at shallow subbottom depths, so they probably have not reached thermal maturity. However, seismic profiles indicate that the sedimentary deposits thicken markedly in a seaward direction where more of the section was deposited under marine conditions; therefore, commercial accumulations of petroleum offshore are more likely. Several potential sources of environmental hazard exist. Among the most important are hurricanes, the Gulf Stream, and earthquakes. The potential danger from high wind, waves, storm surges, and storm-driven currents associated with hurricanes is obvious. Evidence for significant bottom scour by the Gulf Stream is abundant; such scour is a threat to the stability of bottom-mounted structures. The fast-flowing water also will hamper floating drill rigs and control of drill strings. A major earthquake of about magnitude 6.8 struck Charleston in 1886; it may have been associated with a zone of active seismicity that crosses South Carolina. The likelihood of a repetition of the 1886 event is presently not predictable but a seismic hazard must be assumed to exist.

Open-File Report↗

Summary report of the sediments, structural framework, petroleum potential, and environmental conditions of the United States Mid-Atlantic continental margin in area of proposed Oil & Gas Lease Sale No. 59

This report has been compiled to update and summarize the geological information concerning the area of the Atlantic continental margin off the U.S. Mid-Atlantic proposed for Oil and Gas Lease Sale No. 59 (fig. 1). The region of interest lies between 35° and 41° N and 70.5° and 76° W. The north-south dimension is about 660 km (356 nautical miles, 410 statute miles) and the maximum east-west dimension is approximately 250 km (135 nautical miles, 155 statute miles). The area is centered toward the outer Continental Shelf off Delaware and contains more than 154,000 km2 (38,000,000 acres) off the coasts of North Carolina, Virginia, Maryland, Delaware, New Jersey and New York. Water depths within the region range from 20 to slightly more than 4,000 m (fig. 1). This report begins with a discussion of the regional geology and geophysics, followed by a description of the oil and gas potential and potential environmental hazards.

Delaware, Maryland, New Jersey, New York, North Ca↗

Regional geologic framework off northeastern United States

Six multichannel seismic-reflection profiles taken across the Atlantic continental margin off the northeastern United States show an excess of 14 km of presumed Mesozoic and younger sedimentary rocks in the Baltimore Canyon trough and 8 km in the Georges Bank basin. Beneath the continental rise, the sedimentary prism thickness exceeds 7 km south of New Jersey and Maryland, and it is 4.5 km thick south of Georges Bank. Stratigraphically, the continental slope–outer edge of the continental shelf is a transition zone of high-velocity sedimentary rock, probably carbonate, that covers deeply subsided basement. Acoustically, the sedimentary sequence beneath the shelf is divided into three units which are correlated speculatively with the Cenozoic, the Cretaceous, and the Jurassic-Triassic sections. These units thicken offshore, and some have increased seismic velocities farther offshore. The uppermost unit thickens from a fraction of a kilometer to slightly more than a kilometer in a seaward direction, and velocity values range from 1.7 to 2.2 km/sec. The middle unit thickens from a fraction of a kilometer to as much as 5 km (northern Baltimore Canyon trough), and seismic velocity ranges from 2.2 to 5.4 km/sec. The lowest unit thickens to a maximum of 9 km (northern Baltimore Canyon), and velocities span the 3.9 to 5.9-km/sec interval. The spatial separation of magnetic and gravity anomalies on line 2 (New Jersey) suggests that in the Baltimore Canyon region the magnetic-slope anomaly is due to edge effects and that the previously reported free-air and isostatic gravity anomalies over the outer shelf may be due in part to a lateral increase in sediment density (velocity) near the shelf edge. The East Coast magnetic anomaly and the free-air gravity high both coincide over the outer shelf edge on line 1 (Georges Bank) but are offset by 20 km from the ridge on the reflection profile. Because the magnetic-slope-anomaly wavelength is nearly 50 km across, a deep source is likely. In part, the positive free-air gravity anomaly likewise may represent the significant lateral density increase within the sedimentary section toward the outer edge of the shelf.

American Association of Petroleum Geologists Bulle↗

Geophysical evidence for the intersection of the St Paul, Cape Palmas and Grand Cess fracture zones with the continental margin of Liberia, West Africa

PUBLISHED reconstructions of Gondwana continent 1 (Fig. l a ) show a gap in fit near the junction of the Americas and Africa. To study this critical area, the Unitedgeo I made geophysical measurements and collected rock samples across the continental margin of Liberia (USGS-IDOE cruise leg 5) in November 1971. Figure I b indicates the location of the 5,400 km of ship track on a generalised bathymetric map 2 . We shall discuss the data in detail elsewhere. Here we present the evidence for the existence of three fracture zones, two of which have not been reported previously, intersecting the continental margin at the north end of the South Atlantic, which remained closed probably until Cretaceous time. We suggest that Precambrian structures on the African continent controlled the location of these fracture zones. Figure Ic compares gravity and magnetic profiles and interpretations of the seismic profiles for three selected lines (27, 30 and 34) crossing the Grand Cess, Cape Palmas and St Paul fracture zones, respectively.

Nature↗