Search USGS⌕ Search

Geology topics

J.V. Gardner

Publications and source records attributed to J.V. Gardner.

At least 55 records · Page 3Linked to original sources
USGS1992

Map showing sediment isopachs in the deep-sea basins of the Pacific continental margin, Point Conception to Point Loma

The U.S. Geological Survey conducted a series of cruises, EEZSCAN 84 (EEZ-SCAN 84 Scientific Staff, 1986), to collect reconnaissance data on the newly proclaimed Exclusive Economic Zone (EEZ), the area out to 200 nautical miles from the coastline of the United States. The cruises systematically surveyed the entire conterminous United States west coast EEZ using the Geological Long-Range Inclined Asdic (GLORIA) side-scan sonar, a 160-in 3 airgun seismic-reflection profiler, a 3.5-kHz high-resolution seismic-reflection profiler, a 10-kHz echo sounder, and a proton-precession magnetometer. The nominal trackline spacing throughout the survey was 30 km. Derivative maps of sediment thickness (I-2089-A, I-2090-A, I-2091-A) and depth to basement (I-2089-B, I-2090-B, I-2091-B) in the basins of the west coast EEZ were compiled from both the sonar-image dala and the deep-penetration seismic data obtained on these cruises. Only EEZ-SCAN 84 data were used for the map compilations because available data from other cruises in this region are sparsely located, have poor navigational control, or were obtained with seismic systems that were not powerful enough to resolve oceanic basement. For this map series, sediment thickness and depth to basement were determined only in the deep-ocean basin regions because the seismic system used on the EEZ-SCAN 84 cruises could not resolve oceanic basement beneath the thick sediments of the continental slope. All the data used to compile the maps are presented in the "Atlas of the Exclusive Economic Zone, Western Conterminous United States" (EEZ-SCAN 84 Scientific Staff, 1986). Basement Outcrops GLORIA imagery was used to locate areas of basement outcrop throughout the region. Where possible, sediment thickness on and immediately adjacent to basement outcrops was measured from seismic data. Where there was no bathymetric or seismic control, a seamount peak was assumed to have no sediment cover. A pattern is used on the map to indicate all basement outcrops. Data Reduction Acoustic basement in the basins, invariably oceanic Layer 2, was observed on all of the seismic records. One-way traveltime was measured from the sea floor to acoustic basement. Because the trackline spacing of about 30 km is relatively large compared to the data density along track, we chose to measure the sediment thickness every 0.5 hour or at an interval of approximately 7.5 km. Water depth was measured with a 10-kHz profiler. Depth to basement was calculated using the sea surface as the zero datum and adding the corrected water depth (Carter, 1980) to the sediment thickness. Acoustic travel times were converted to depths by first calculating a regression equation from the interval velocity versus depth data of Connard and others (1984). Their data base comprises a compilation of all available Deep Sea Drilling Project data plus wide-angle refraction data, which were collected in Cascadia Basin west of Oregon and represents the best data set available for the United States west coast EEZ. The regression equation was integrated to determine sediment thickness as a function of one-way traveltime . The resulting equation is z = 1400t + 0 .5t 2 where z is sediment thickness in meters, and t is one-way traveltime in seconds. Sediment thicknesses calculated using this equation were compared to values calculated from the general equation of Carlson and others (1986). Values for sediment thickness calculated by the two equations differed by no greater than 10 percent throughout the range of travel times. Bathymetry The bathymetry is from Chase and others (1981). The bathymetric data were compiled from a variety of sources, and data quality is inconsistent. Because of differences in navigational precision and density of coverage, the bathymetric contours of a feature may be at a different location than the corresponding isopleths derived from the EEZ-SCAN 84 data, or a feature may not be indicated on the bathymetry at all. These situations occur because either the feature is poorly located in the bathymetric data set or, especially in the outer EEZ, the bathymetric data are too sparse to have defined the existence of a feature. Acknowledgments Topographic digital data bases were corrected and verified by Christina Lief. Gerald Evenden developed the computer software system MAPGEN, used to compose this map. Reviews, suggestions, and technical contributions from Edward C. Escowitz and Florence Wong and advice about cartographic design from Will Stettner substantially improved the quality of this map. References Cited Carlson, R.L., Gangi, A.F., and Snow, K.R., 1986, Empirical reflection-traveltime/ depth and velocity/depth functions for the deep-sea sediment column: Journal of Geophysical Research, v. 91, no. B8, p. 8249-8266. Carter, D.J.T., 1980, Echo-sounding correction tables: Taunton, United Kingdom, Hydrographic Department, Ministry of Defence, 150 p. Chase, T.E., Wilde, Pat, Normark, W.R, Miller, C.P., Seekins, B.A., and Young, J.D., 1981, Offshore topography of the Western United States between 32° and 49° North latitudes: U.S. Geological Survey Open-File Report 81-443, scale 1:864,518 at 38° latitude, 2 sheets. Connard, G., Couch, R., Keeling , K., Roy, J., and Troseth, S., 1984, Abyssal plain and continental net-objective sedimentary thicknesses, in Kulm, L.D., and others, eds., Western North America continental margin and adjacent ocean floor off Oregon and Washington, Atlas 1 of Regional Atlas Series, Ocean Margin Drilling Program: Woods Hole, Mass., Marine Science International, sheet 7. EEZ-SCAN 84 Scientific Staff, 1986, Atlas of the Exclusive Economic Zone, Western Conterminous United States: U.S. Geological Survey Miscellaneous Investigations Series I-1792, scale 1:500,000, 152 p. index map for I-2089-A See Also "U.S. Pacific West Coast Field Activities" (Paskevich and others, 2011; http://pubs.usgs.gov/of/2010/1332/htmldocs/pc/pc_overview.html). Paskevich, V.F., Wong, F.L., O?Malley, J.J., Stevenson, A.J., and Gutmacher, C.E., 2011, GLORIA sidescan-sonar imagery for parts of the U.S. Exclusive Economic Zone and adjacent areas: U.S. Geological Survey Open-File Report 2010?1332, available at http://pubs.usgs.gov/of/2010/1332/.

IMAP↗
USGS1992

Map showing depth to basement in the deep-sea basins of the Pacific continental margin, Point Conception to Point Loma

The U.S. Geological Survey conducted a series of cruises, EEZSCAN 84 (EEZ-SCAN 84 Scientific Staff, 1986), to collect reconnaissance data on the newly proclaimed Exclusive Economic Zone (EEZ), the area out to 200 nautical miles from the coastline of the United States. The cruises systematically surveyed the entire conterminous United States west coast EEZ using the Geological Long-Range Inclined Asdic (GLORIA) side-scan sonar, a 160-in 3 airgun seismic-reflection profiler, a 3.5-kHz high-resolution seismic-reflection profiler, a 10-kHz echo sounder, and a proton-precession magnetometer. The nominal trackline spacing throughout the survey was 30 km. Derivative maps of sediment thickness (I-2089-A, I-2090-A, I-2091-A) and depth to basement (I-2089-B, I-2090-B, I-2091-B) in the basins of the west coast EEZ were compiled from both the sonar-image dala and the deep-penetration seismic data obtained on these cruises. Only EEZ-SCAN 84 data were used for the map compilations because available data from other cruises in this region are sparsely located, have poor navigational control, or were obtained with seismic systems that were not powerful enough to resolve oceanic basement. For this map series, sediment thickness and depth to basement were determined only in the deep-ocean basin regions because the seismic system used on the EEZ-SCAN 84 cruises could not resolve oceanic basement beneath the thick sediments of the continental slope. All the data used to compile the maps are presented in the "Atlas of the Exclusive Economic Zone, Western Conterminous United States" (EEZ-SCAN 84 Scientific Staff, 1986). Basement Outcrops GLORIA imagery was used to locate areas of basement outcrop throughout the region. Where possible, sediment thickness on and immediately adjacent to basement outcrops was measured from seismic data. Where there was no bathymetric or seismic control, a seamount peak was assumed to have no sediment cover. A pattern is used on the map to indicate all basement outcrops. Data Reduction Acoustic basement in the basins, invariably oceanic Layer 2, was observed on all of the seismic records. One-way traveltime was measured from the sea floor to acoustic basement. Because the trackline spacing of about 30 km is relatively large compared to the data density along track, we chose to measure the sediment thickness every 0.5 hour or at an interval of approximately 7.5 km. Water depth was measured with a 10-kHz profiler. Depth to basement was calculated using the sea surface as the zero datum and adding the corrected water depth (Carter, 1980) to the sediment thickness. Acoustic travel times were converted to depths by first calculating a regression equation from the interval velocity versus depth data of Connard and others (1984). Their data base comprises a compilation of all available Deep Sea Drilling Project data plus wide-angle refraction data, which were collected in Cascadia Basin west of Oregon and represents the best data set available for the United States west coast EEZ. The regression equation was integrated to determine sediment thickness as a function of one-way traveltime . The resulting equation is z = 1400t + 0 .5t 2 where z is sediment thickness in meters, and t is one-way traveltime in seconds. Sediment thicknesses calculated using this equation were compared to values calculated from the general equation of Carlson and others (1986). Values for sediment thickness calculated by the two equations differed by no greater than 10 percent throughout the range of travel times. Bathymetry The bathymetry is from Chase and others (1981). The bathymetric data were compiled from a variety of sources, and data quality is inconsistent. Because of differences in navigational precision and density of coverage, the bathymetric contours of a feature may be at a different location than the corresponding isopleths derived from the EEZ-SCAN 84 data, or a feature may not be indicated on the bathymetry at all. These situations occur because either the feature is poorly located in the bathymetric data set or, especially in the outer EEZ, the bathymetric data are too sparse to have defined the existence of a feature. Acknowledgments Topographic digital data bases were corrected and verified by Christina Lief. Gerald Evenden developed the computer software system MAPGEN, used to compose this map. Reviews, suggestions, and technical contributions from Edward C. Escowitz and Florence Wong and advice about cartographic design from Will Stettner substantially improved the quality of this map. References Cited Carlson, R.L., Gangi, A.F., and Snow, K.R., 1986, Empirical reflection-traveltime/ depth and velocity/depth functions for the deep-sea sediment column: Journal of Geophysical Research, v. 91, no. B8, p. 8249-8266. Carter, D.J.T., 1980, Echo-sounding correction tables: Taunton, United Kingdom, Hydrographic Department, Ministry of Defence, 150 p. Chase, T.E., Wilde, Pat, Normark, W.R, Miller, C.P., Seekins, B.A., and Young, J.D., 1981, Offshore topography of the Western United States between 32° and 49° North latitudes: U.S. Geological Survey Open-File Report 81-443, scale 1:864,518 at 38° latitude, 2 sheets. Connard, G., Couch, R., Keeling , K., Roy, J., and Troseth, S., 1984, Abyssal plain and continental net-objective sedimentary thicknesses, in Kulm, L.D., and others, eds., Western North America continental margin and adjacent ocean floor off Oregon and Washington, Atlas 1 of Regional Atlas Series, Ocean Margin Drilling Program: Woods Hole, Mass., Marine Science International, sheet 7. EEZ-SCAN 84 Scientific Staff, 1986, Atlas of the Exclusive Economic Zone, Western Conterminous United States: U.S. Geological Survey Miscellaneous Investigations Series I-1792, scale 1:500,000, 152 p. index map for I-2089-A See Also "U.S. Pacific West Coast Field Activities" (Paskevich and others, 2011; http://pubs.usgs.gov/of/2010/1332/htmldocs/pc/pc_overview.html). Paskevich, V.F., Wong, F.L., O?Malley, J.J., Stevenson, A.J., and Gutmacher, C.E., 2011, GLORIA sidescan-sonar imagery for parts of the U.S. Exclusive Economic Zone and adjacent areas: U.S. Geological Survey Open-File Report 2010?1332, available at http://pubs.usgs.gov/of/2010/1332/.

IMAP↗
USGS1991

Valencia gorge: Possible Messinian refill channel for the western Mediterranean Sea

A deeply incised gorge is buried nearly 800 m beneath the floor of the Valencia Trough in the western Mediterranean Sea. The gorge is steeply cut more than 200m into Messinian evaporite deposits and has been mapped for more than 40 km. Published and unpublished seismic profiles show the total length to be nearly 300 km. The gorge is not aligned with any known large fluvial systems, and its orientation indicates that it may have been connected near Valencia with the Betic Strait, the portal in southern Spain proposed to link the Atlantic and the western Mediterranean. The Betic Strait was probably open at least through early Messinian time. Conservative estimates show that sea water flowing through the Valencia gorge at rates of 0.5 to 2 m/s could have refilled the western Mediterranean basins below 2000 m in less than 50 yr.

Geology↗
USGS1990

Inorganic geochemistry of surface sediments of the Ebro shelf and slope, northwestern Mediterranean

Distributions of major, minor, and trace elements in surface sediment of the continental shelf and upper slope of the northeastern Spanish continental margin reflect the influences of discharge from the Ebro River and changes in eustatic sea levels. Multivariate factor analysis of sediment geochemistry was used to identify five groupings of samples (factors) on the shelf and slope. The first factor is an aluminosilicate factor that represents detrital clastic material. The second factor is a highly variable amount of excess SiO 2 and probably represents a quartz residuum originating from winnowing of relict detrital sediments. A carbonate factor (Factor 3) has no positive correlation with other geochemical parameters but is associated with the sand-size fraction. The carbonate in these sediments consists of a mixture of biogenic calcite and angular to subangular detrital grains. Organic carbon is associated with the aluminosilicate factor (Factor 1) but also factors out by itself (Factor 4); this suggests that there may be two sources of organic matter, terrestrial and marine. The fifth factor comprises upper slope sediments that contain high concentrations of manganese. The most likely explanation for these high manganese concentrations is precipitation of Mn oxyhydroxides at the interface between Mn-rich, oxygen-deficient, intermediate waters and oxygenated surface waters.

Marine Geology↗
USGS1990

Sedimentary evolution of the Pliocene and Pleistocene Ebro margin, northeastern Spain

The Pliocene and Pleistocene deposits of the Spanish Ebro margin overlie a regional unconformity and contain a major disconformity. These unconformities, named Reflector M and Reflector G, mark the bases of two seismic sequences. Except for close to the upper boundary where a few small channel deposits are recognized, the lower sequence lacks channels. The upper sequence contains nine channel-levee complexes as well as base-of-slope aprons that represent the proximal part of the Valencia turbidite system. Diverse geometries and variations in seismic units distinguish shelf, slope, base-of-slope and basin-floor facies. Four events characterize the late Miocene to Pleistocene evolution of the Ebro margin: (a) formation of a paleodrainage system and an extensive erosion-to-depositional surface during the latest Miocene (Messinian), (b) deposition of hemipelagic units during the early Pliocene, (c) development of canyons during the late Pliocene to early Pleistocene, and (d) deposition of slope wedges, channel-levee complexes, and base-of-slope aprons alternating with hemipelagic deposition during the Pleistocene. Sea-level fluctuations influenced the evolution of the sedimentary sequences of the Ebro margin, but the major control was the sediment supply from the Ebro River.

Marine Geology↗
USGS1990

Expression of seasonal and ENSO forcing in climatic variability at lower than ENSO frequencies: Evidence from Pleistocene marine varves off California

Upper Pleistocene marine sediments along the upper continental slope off northern and central California contain alternations of varved and bioturbated sediments and associated changes in biota and sediment composition. These alternations can be related to conditions that accompany El Niño and anti-El Niño (ENSO) circulation. Anti-El Niño conditions are characterized by increased upwelling and productivity and by low concentrations of dissolved oxygen in the oxygen minimum zone that resulted in varve preservation. El Niño conditions are characterized by little or no upwelling, low productivity, and higher concentrations of dissolved oxygen that resulted in zones of bioturbation. Alternations of varves and zones of bioturbation, that range from decades to millennia, occur through the upper Pleistocene section. The inferred long-term alternations in El Niño and anti-El Niño conditions appear to be a re-expression of ENSO's primary 3–7 year cycle. Decadal to millennial cycles of productivity associated with El Niño and anti-El Niño conditions may have served as a “carbon pump” and transferred atmospheric CO 2 to the marine reservoir. Changes in sediment composition and organisms associated with El Niño or anti-El Niño conditions can be related to both seasonal and ENSO phenomena. Expression of these changes at lower-than-ENSO frequencies may be partly explained by adding the effects of seasonal variability to effects produced by a self-oscillating ENSO system. However, deterministic mechanisms, including solar modulation of ENSO, may also contribute to long-term alternations of El Niño and anti-El Niño conditions.

Palaeogeography, Palaeoclimatology, Palaeoecology↗
USGS1989

Influence of Shimada Seamount on sediment composition in the eastern tropical North Pacific

Shimada Seamount is a large, young volcanic edifice in the east-central Pacific that is not associated with any active spreading center or known hot spot. The sediments on the abyssal plain surrounding Shimada Seamount consist of pelagic clay with ferromanganese micronodules and zeolites. The pelagic clay is mostly barren of microfossils except for a few occurrences of highly corroded specimens of Radiolaria and diatoms. Eolian terrigenous material is the dominant component of the pelagic clay to a depth of at least 8 m below sea floor, with minor contributions from volcanic debris and hydrothermal and hydrogenous sources. The average amount of basaltic debris is only 0.25%, but concentrations are as high as 10% in some samples. The average hydrothermal component (metalliferous sediment) is 8.8% with a maximum of about 13% at 7.5 m below sea floor in one core. The hydrogenous component, mostly as ferromanganese micronodules, averages 4.1% with a maximum of 5.6%. There is no calcareous biogenic debris and essentially no siliceous biogenic debris. In the past, a decrease in hydrothermal components through time may have been the result of a decrease in relative importance of hydrothermal influences, or an increase in the flux of terrigenous debris transported by the northeast trade winds. Because volcanic activity is still active on Shimada Seamount, or has been in the recent past, the observed increase in relative abundance of terrigenous components probably was the result of increased wind transport and not decreased hydrothermal activity. Shimada Seamount may be an important local source of metalliferous sediment in the eastern equatorial North Pacific, and may have been an even more important source in the past.

Geochimica et Cosmochimica Acta↗
USGS1987

Benthic foraminifers on the continental shelf and upper slope, Russian River area, northern California ( USA).

We analyzed benthic foraminifers from 71 surface samples collected from the sea floor of the continental margin. One hundred and six different taxa were identified, and Q-mode factor analysis was used to identify assemblages. Six foraminiferal assemblage factors explain 94% of the variation in the data matrix. The Inner Shelf Assemblage is characterized by Trichohyalus ornatissima, Rotalia columbiensis, Cassidulina limbata, Cibicides fletcheri, Elphidiella hannai and Elphidium sp. 1 and occupies water depths less than 50 m. The Middle Shelf Assemblage is characterized by Nonionella basispinata, Elphidium excavatum and Florilus labradoricus and occupies water depths between 50 and 90 m. A Middle Shelf to Upper Bathyal Assemblage is characterized by Uvigerina juncea, Globobulimina spp. and Nonionella basispinata and occupies depths between about 90 and 450 m. Two overlapping assemblages make up the Upper Middle Bathyal Assemblage and are most abundant between water depths of 500 and 1300 m. They are associated with low- oxygen conditions. The Mid-Bathyal Assemblage is dominated by Uvigerina proboscidea and occurs on the slope at water depths ranging from 1200 to 2500 m. -from Authors

Journal of Foraminiferal Research↗
USGS1986

Evidence for a stronger oxygen-minimum zone off central California during late Pleistocene to early Holocene

Of 31 deep-sea cores collected along the central California continental slope, 18 have distinctly laminated sediment at depth, but none have laminations in the top few centimetres. The cores with laminated facies are restricted to water depths between 508 and 1508 m, but not all cores taken from this depth interval have laminated facies. 14 C dates yield an extrapolated age of 4700 B.P. for the top of the uppermost laminated unit. Comparisons of the diatom flora in the laminated couplets with diatom floras in a 13-month sediment-trap record suggest that the laminations are varvelike couplets of seasonal sedimentation. The laminated facies represent a period from the last global deglaciation to early Holocene when the oxygen-minimum zone along the northeastern Pacific Ocean was stronger than at present. A stronger oxygen-minimum zone during this time is inferred to be the result of intensified upwelling.

Geology↗
USGS1985

Palaeotectonic implications of increased late Eocene-early Oligocene volcanism from South Pacific DSDP sites

Late Eocene-early Oligocene (42-35 Myr) sediments cored at two DSDP sites in the south-west Pacific contain evidence of a pronounced increase in local volcanic activity, particularly in close association with the Eocene-Oligocene boundary. This pulse of volcanism is coeval with that in New Zealand and resulted from the development of an Indo- Australian / Pacific Plate boundary through the region during the late Eocene. The late Eocene / earliest Oligocene was marked by widespread volcanism and tectonism throughout the Pacific and elsewhere, and by one of the most important episodes of Cenozoic climatic cooling. ?? 1985 Nature Publishing Group.

Nature↗